Search Documents

By Bruno Pinheiro Silva, João José dos Santos Carvalho, Flávio Túlio Busatto, Leonardo Passos Perdigão

Sinter has high participation in the blast furnaces ferrous burden in ArcelorMittal Tubarão, being therefore of paramount importance the constant control of its physical, chemical and metallurgical qualities, aiming at the fulfillment of the client required quality. With the great challenges faced by market conditions, steelmaking companies seek operational sustainability, aiming at stability and reducing costs. One of the main steps to obtain these results in the Blast Furnaces is the raw materials quality stabilization, in order to guarantee the perfect burden distribution control and a better use of the reductant gas inside the reactor, aiming a lower fuels consumption. It is known that the smaller a ferrous particle is, better its reducibility, since a larger surface area provides greater contact with the reductant agent. Based on this concept, the objective of this work is to quantify the effect of the sinter size produced in ArcelorMittal Tubarão Sinter Plant in its reducibility, and in this way enable the definition of a better sinter particle size distribution aiming at a balance between the permeability effects and gaseous yield in the Blast Furnaces. In addition, the reducibility effects on sinter size reduction were evaluated, where the 5 to 10 mm fraction was analyzed in two sinter samples, the first obtained from the conventional route and the second after crushing of the fraction over 50 mm, in order to simulate the effect of the use of a Secondary Crusher in Sintering.

Oct 1, 2019

By Denisio Miranda Custódio, Rodrigo Boyer, Josiane Lira Batista Haagensen, Raquel Teixeira Pereira, Felipe Viana Pimenta, Rossano Augusto Pilon Nunes

In the Tubarão Pelletizing Plants, anthracite is used as solid fuel, which has fixed carbon content of 72%. This paper will present the pilot scale results and industrial scale tests of an alternative fuel to anthracite, named Blast Furnace Dust. All the work was developed using samples from Arcelor Mittal Tubarão, due to it has a large source of production and is near to Vale/SA, which reduces significantly the cost for the material’s transportation. There was an impact on the variability in fixed carbon results of the slurry, mainly at the beginning of the test, reaching very high levels and put on risk the pellets physical’s quality. This variation can be explained by some operational disturbances and, mainly, by the low predictability of Blast Furnace Dust quality and lack of an adequate system for material preparation and dosage.

Oct 1, 2019

By Ismael Vemdrame Flores, Lindaura de Souza Cândido D’ Avila, Maurício Covcevich Bagatini, Arthur Felipe Lino Oliveira, Rafael Adriano Lopes Júnior

The use of pellet feed to adjust the chemical quality of the sinter is an alternative to the depletion of iron ore reserves. However, the addition of ultrafine in the sintering process can cause decrease of permeability and consequent drop in machine productivity. In this context, the present work investigated the addition of natural and ground pellet feed, evaluating its effects on cold agglomeration for sintering and quality of quasi-particles produced. Eight typical mixtures with industrial composition were produced in the laboratory, replacing Sinter Feed with different percentages of Natural Pellet Feed (NPF, 91% <150 μm) and Ground Pellet Feed (GPF, 83% <44 μm). The mixtures were subjected to cold agglomeration tests and the quasi-particles produced were evaluated by screening, shatter test, permeability test and disintegration into primary particles analysis. There was a decrease in the mean particle size of quasi-particles and reduce in permeability with addition of the ultrafines. The addition of NPF favored the layering mechanism in larger quasi-particles. The coalescence mechanism occurred for larger additions of NPF and GPF, being more expressive for GPF additions.

Oct 1, 2019

By Lilian Silva Costa, Laila Bonzi Ramos, Marcela Lessa de Freitas, Igor Quaresma Vianna

The eighth pelletizing plant, located at the Tubarão complex Industrial Unit of Vale S/A in Vitória-Espirito Santo-ES, processes a pellet feed primarily composed of compact and friable itabirite from Itabira and Brucutu concentration plants, located in the iron quadrangle in Minas Gerais-MG. The use of hydrated ores in the composition of the fine piles, such as Brucutu's common fines amphibolite itabirite (FABR), and Fábrica Nova pellet feed (PEFN), contributed to increase the energy efficiency of comminution, increasing the production of tumbling ball mills, minimizing the impacts during a mill preventive maintenance.

Oct 1, 2019

By Thiago Pinto Silva, Leandro Rocha Lemos, Luiz Fernando Andrade de Castro

This paper shows an evaluation about effect of dispersant sodium silicate along to limestone, in the form of pulp, on the cold agglomeration process for iron ore sintering. Before that, it was verified the effect of pH, solids content and amount of dispersant on the stability of the system (limestone, water and sodium silicate). It was found that the lower the solids content, the more alkaline pH and the amount of sodium silicate equal to 20 l for each 1t of limestone, was the level of dispersion of the system. The influence of the limestone pulp with dispersant depended on the granulometry of the ore mixture and the type of technological route. For the thinner type (42,8% <0.15mm), the limestone pulp with dispersant reduced the resistance of the adherent layer of the cold agglomerates, regardless of the technological route. However, for the coarser type (24,7% <0.15mm), the limestone pulp with dispersant increased the average size of the aggregates, preserving the resistance of the adherent layer when manufacturing with two intensive mixers in series.

Oct 1, 2019

By Walter Luiz Castro dos Santos, Leandro Resinentti Zanon

In the production of iron ore pellets, one of the factors that strongly influence the cost of ore-pellet processing is the specific consumption of natural gas that occurs during the thermal processing stage of the pellets. The filtration process is the step where the adequacy of the moisture percentage of the retained pulp occurs, so that subsequently there is the processing in the subsequent stages of the pellet formation and hardening of pellets. The water contained in the raw pellet is withdrawn at the stage of thermal processing. For this purpose, the literature indicates the demand of 600 Kcal/kg of water for the heating and vaporization of the moisture of raw pellets. The statistical analysis of the performance data of a pelletizing plant showed that for each decrement of 0.1% of water in the retained pulp is equivalent to the reduction of 0.091 Nm3 in the consumption of natural gas per tonne of pellets produced. Thus, the proper performance of the filtration stage is essential to reduce the percentage of pulp moisture retained and consequently to increase the energy efficiency of the pelletizing furnaces. The aim of this article is to present the main steps in conducting a work to increase the filtration performance to reduce the percentage of retained pulp moisture and the positive impacts on the specific natural gas consumption of a plant Pelletizing.

Oct 1, 2019

By Paula Maria Gomes Cunha Leão, Flávio de Castro Dutra, Fabrício Vilela Parreira, Silvio Maranha

In the iron ore beneficiation, tailings are inherent in the concentration processes to which the ores are subjected for the production of commercial products. The large generation of tailings has been motivating the study of technological alternatives for its reuse, with the development of processes that contemplate the concentration of fine ore particles present in the tailings, such as the reintroduction of these particles in the process of manufacture of the iron and steel itself, through the agglomeration techniques such as briquetting. The aim of this article is to study the technical feasibility of the production of iron ore tailings and coking coal briquettes for use in reduction reactors, through a systematic review of the literature on agglomeration, briquetting and self-reduction processes, covering the main variables that influence the production of high quality briquettes, such as binders use, binder behavior of coking coal, coal granulometry, iron ore and coal proportion, compacting pressure and temperature of thermal treatment and the effects of these variables on briquettes final properties.

Oct 1, 2019

By Davi Silva Braga, Alexssander Lopes Sampaio, Rodrigo Carneiro de Oliveira

Vallourec was world pioneer in the deployment, development and consolidation of technology for the use of pulverized charcoal as the main energy source on the first Grate-kiln pelletizing plant in Brazil. The objective of this work was to delve into the subject and to bring more information about this innovative practice of Vallourec that has been attracting the attention of other companies in the steel industry. Industrial tests confirmed the technical feasibility, taking Vallourec ahead in the project of adaptation and investment. With consolidated data of two years and five months from the beginning of the implementation, the main benefits are the average reduction of CO₂e emissions by 50%, cost reduction higher than expected and return on investment in just 19 months.

Oct 1, 2019

By Artur Frederico Fonseca da Cruz, Jael Moutinho dos Santos

The problem of iron ore sticking and premature wear on screening rolls on balling systems is recurrent. The importance of the "screening" function of the roller classifier is fundamental, since in perfect conservation state and operation it is possible to ensure the performance improvement of the most expensive phase in the pelletizing production chain, the thermal processing. The present works target is the identification of possible causes of iron ore adhesion in classifier rollers and develop a methodology to evaluate and quantify the iron ore sticking mechanism on the classifier surface. For this purpose, iron ore and additives were collected at four different pelletizing plants in terms of iron ore origins and process flows, three different rollers were chosen for testing around the adhesive energy at the iron ore mixture/rolls surface interface. As results, it was possible to construct methodologies to evaluate the aggregability, it was observed the importance of "specific moisture" definition and knowledge on the adhesive energy increase, besides presenting the better performance of rolls with tungsten carbide coating than other evaluated.

Oct 1, 2019

By Luís Marcelo Marques Tavares, Gilvandro Bueno, Túlio MoreiraCampos

The HPGR development and application in the minerals industry resulted in an important increase in its application in iron ore pellet feed processing in the last decades. Vale SA was one of the pioneers in application of the HPGR in integrated plants, currently operating with six HPGRs in the pelletizing plants of Complexo de Tubarão (Vitória, ES). The work uses the mathematical model of the HPGR, proposed by Torres & Casali and modified by the present authors, to predict the performance of two industrial pellet feed HPGR units of the Complexo de Tubarão. Besides model validation, results of process simulations are shown in order to optimize the pellet feed pressing according to industrial demands, presenting different scenarios that are more attractive to HPGR operation. Simulations showed that it is feasible to reduce the specific surface area of the HPGR feed from 1770 cm²/g to 1570 cm²/g, allowing to produce a pellet feed of the same quality in its product (1911 cm²/g) and therefore reduce the work done by upstream ball milling.

Oct 1, 2019

By Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Beatriz Fausta Gandra

A composição química do gás redutor afeta, de forma marcante, sua difusividade através do leito e a capacidade de redução da carga metálica. Associado a isto, o cenário econômico e ambiental indica a necessidade de se buscar cada vez mais elevada produtividade dos altos-fornos, com baixo consumo de combustível e menor emissão de CO2. Para tanto, as empresas têm buscado operar com elevada taxa de injeção de carvão e, em casos de política favorável, intensificar o uso de gás natural em altos-fornos. Nestes casos, a quantidade de material reduzida via H2, em comparação ao CO, é aumentada. No presente trabalho, são apresentados os resultados de ensaios em amolecimento e fusão (A&F) de dois tipos de granulados, de um tipo de pelota e de um sínter industrial, utilizando-se como redutor um gás com diferentes teores de H2 (0% a 12%). Verificou-se que, para o granulado, não há uma tendência definida. Embora um maior teor de hidrogênio possa favorecer a redução, isto não refletiu em melhor permeabilidade do leito. No caso da pelota estudada, houve leve tendência de melhora nos parâmetros avaliados quando se tem o gás mais rico em hidrogênio. No entanto, seu desempenho em A&F foi muito aquém daquele esperado para este tipo de carga, uma vez que apresentou elevada resistência à permeabilidade associada à baixa redutibilidade até o início do amolecimento. Para o sínter, foi identificada evidente melhora nos aspectos de redução e de permeabilidade do leito.

Oct 1, 2019

By José Geraldo da Silveira, Luiz José Gonçalves, André Mendes Carneiro Lyrio, Raylander Rocha Pessoa, Péricles Guimarães Oliveira Aguiar, Guilherme Ribeiro do Espírito Santo, Filipe Soares Pontes

Este trabalho tem como objetivo apresentar a origem do projeto inovador do cadinho do Alto-forno 2 além do planejamento, a implantação e os resultados obtidos no Alto-forno 2 da Aperam South America após a reforma. O trabalho de pesquisa e desenvolvimento teve início em 2012 após a primeira marcha fria com conseqüente redução das temperaturas da soleira. Foram realizadas diversas reuniões, discussões e seminário sobre alto-forno com especialistas de diversas empresas. A mudança de redutor carvão vegetal para coque por seis meses serviu para comprovar parte da teoria construída pelo time da redução. Para, por fim, culminar no conceito por trás do problema do AF2 e então o novo design do cadinho que foi proposto e implantado na reforma iniciada em dezembro de 2017. Após sua implantação, conforme teorizado pelo time, uma nova gama de resultados e patamar de operação foram atingidos, comprovando diversas das teorias formuladas.

Oct 1, 2019

By Cameron Soltys, Hamid Ghorbani, Maher Al-Dojayli

Cooling staves in blast furnaces are used to minimize the process heat loads on steel shell and refractory system. Copper staves are exposed to significant fluctuating thermal loads which may lead to premature stave failures due to cracks, water leakage, bending, abrasion and resultant wear. In this paper, an assessment methodology is presented to evaluate the effect of thermal cycling on copper staves including bending, fatigue and thermal ratcheting. This approach incorporates temperature-dependent copper properties including creep and plasticity to more accurately capture inelastic deformations, damage and fatigue in staves under transient and cyclic thermal loading conditions. Root cause failure assessment and improvements to copper stave design can be assessed using the presented methodology.

Oct 1, 2019

By Flaviani Marculano Marchesi, Silas Gambarine Soares, Elton Volkers do Espírito Santo, Felipe Fardin Grillo, Heitor Cristo Clem de Oliveira

O objetivo deste trabalho é utilizar a termodinâmica computacional para estudar as propriedades de escórias iniciais dessulfurantes utilizando misturas com diferentes fluxantes: fluorita, sodalita, borra de alumínio, B2O3 e ilmenita. A princípio, as misturas foram definidas e em seguida foram realizadas simulações para o aquecimento dessas misturas a 1350 ºC por meio do software FactSage 7.2. Assim, foi calculado o fator de dessulfuração (FDeS) para cada mistura com base nas condições de equilíbrio. As misturas contendo 5 e 10% de fluorita e 5% de sodalita foram as que apresentaram maior FDeS. Em contrapartida, as misturas com 10,15 e 20% de B2O3 tiveram os piores resultados nessa análise. Misturas da literatura também foram simuladas a fim de se obter o FDeS e relacioná-lo com a eficiência.

Oct 1, 2019

By Christian Overhagen

In bar and wire rod mills, rolling procedures featuring three- and four-roll technologies are state-of-the-art to produce high-quality long products. While a rolling model for the three-roll process including an equivalent pass method was already presented by the author, pass design methods are dealt with in the current work. The geometry of the rolled product and roll grooves are described mathematically using functional contours, allowing geometric-numerical methods to be used for manipulation and deformation simulation of the rolled product. For a given pass, the output section is constructed using these methods. Roll force, torque and rolling power are calculated using the mathematical rolling model presented before. Interstand tensions are discussed as influencing parameters on the force, torque and power demands, as well as on the section shape. A mathematical model for the influence of interstand tensions on lateral spread is incorporated in the model. To complete the pass design model, elastic mill stand feedback is considered in terms of a fixed elastic modulus for each rolling stand, the elastic feedback and therefore cross-sectional variation due to elastic mill spring being calculated iteratively from the roll force by application of the Gagemeter equation. The interaction of section height and width faults due to elastic mill spring and spread variations is analyzed in detail and the consequences for the roll pass design are shown.

Oct 1, 2019

By Johne Jesus Mol Peixoto, João Victor Gomes Guimarães Ananias, Itavahn Alves da Silva, Thiago Araújo Santos de Oliveira, Weslei Viana Gabriel, Carlos Antônio da Silva, Salvatore Giuliano PeixotoTropia

O arraste de escória para o distribuidor, durante a drenagem de panelas de aço, tem grande impacto no rendimento metálico, limpidez e produtividade no processo de lingotamento contínuo. Modelamento físico e matemático foram utilizados para o estudo da formação do escoamento tipo vórtice e funil no esgotamento de panelas de aço. Em um modelo em escala 1:6,5 foi avaliada a influência da vazão de drenagem, altura inicial de líquido, temperatura do banho e estratificação da temperatura sobre a altura crítica (Hcr) de formação de vórtice. Para todas as condições experimentais, o valor de Hcr se mostrou crescente com o aumento da vazão, respeitando uma relação linear. Através da técnica de Particle Image Velocimetry – PIV observou-se o desenvolvimento do campo de velocidades sub-superficiais da água durante a drenagem em modelo de acrílico em escala 1:6,5. Os resultados das simulações fluidodinâmicas obtiveram bom acordo com os experimentos físicos, e foram capazes de representar a influência da vazão e da temperatura sobre o valor de Hcr.

Oct 1, 2019

By Leonardo Barboza Trindade, José Ernesto de Azevedo Nadalon, Eduardo Netto de Souza, Bruno Pessoa Ramos

O agitador eletromagnético no processo de lingotamento contínuo tem se mostrado útil na melhoria de qualidade das estruturas de solidificação, inibindo a formação de estruturas colunares, aumentando desta forma, a fração de estruturas equiaxiais, promovendo redistribuição de soluto e atenuações de defeitos através de movimentos induzidos no líquido pelo campo magnético. Baseado nas características do agitador eletromagnético do molde (M-EMS) de uma máquina de lingotamento de tarugos, foram realizadas simulações fluidodinâmicas (CFD) sob influência do campo eletromagnético, visando analisar o comportamento do escoamento e da temperatura. Um segundo objetivo foi avaliar o efeito do agitador sobre a trajetória das inclusões e como poderia promover a melhoria da qualidade subsuperficial das estruturas de solidificação. Foram testadas diferentes frequências e correntes de operação do M-EMS, bem como o posicionamento das válvulas submersas com diferentes configurações de furos de saída. Os resultados mostraram a percentagem de partículas sólidas removidas do domínio e a influência do agitador na extração de calor do molde, de forma a tornar mais homogênea a distribuição de temperatura durante o processo de solidificação.

Oct 1, 2019

By Matheus Porto Trindade, Marcos Menino de Macedo Filho, Isau de Souza Alves Junior, Sandro Griza, Brenno Lima Nascimento, Gustavo Dória Lima

O tratamento de oxidação térmica da liga Ti-6Al-4V foi realizado ao ar a 600 °C durante 2h, 5h e 10 h. O comportamento à fadiga foi analisado e comparado com aquele da liga não tratada. Foi feita caracterização através de análise por microscopia ótica e eletrônica, difração de raios-x e medição da rugosidade. Os resultados do DRX demonstraram crescimento dos picos de rutilo. Verificou-se um aumento na espessura média da camada formada de 0,12 μm para 1,09 μm ao elevar a duração do tratamento de 2 para 10 h. Os resultados apontaram redução de resistência a fadiga de 35 % para amostras oxidadas durante 2 h, 27 % para amostras oxidadas por 5 h e 29 % para as amostras tratadas durante 10 h, em relação ao ensaio com corpos de prova não submetidos ao tratamento. O efeito prejudicial causado pela camada formada após oxidação de 2 h foi tão danoso quanto o causado pela camada formada após 10 h, apesar da diferença entre as espessuras das camadas. A morfologia encontrada nas amostras fraturadas indicou fragilização na superfície das amostras oxidadas, contribuindo para a nucleação de trincas iniciais nos primeiros ciclos de fadiga na camada que favoreceram a propagação de fadiga, independendo da espessura de camada.

Oct 19, 2019

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019

By André Oliveira Galon, Caio Vaccari Silva, Victor Bridi Telles, Raphael Mariano de Souza, Felipe Fardin Grillo, José Roberto de Oliveira

Neste trabalho foi estudada a influência da granulometria de CaO adicionada ao processo de desfosforação, temperatura e teor de FeO da mistura desfosforante na aglomeração de partículas sólidas na escória. Para isto, foram realizados testes laboratoriais em sete condições experimentais distintas, bem como a análise de imagens via software Quantikov, para medir a aglomeração, além de análise termodinâmica computacional. A granulometria, temperatura e porcentagem de FeO se mostraram parâmetros relevantes na aglomeração da escória de desfosforação e a análise de imagens mostrou-se uma ferramenta útil para a obtenção destes resultados.

Oct 1, 2019