Search Documents

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

By A. E. Back

A method is described in which particulate iron, as distinguished from high purity iron powders used in powder metallurgy, is a precipitant for copper contained in dilute solutions. A new precipitation apparatus utilizes particulate iron precipitants to recover copper more efficiently than is possible in a conventional launder precipitation plant. In the search for lower cost methods of recovering copper from mine water, the use of sponge iron or particulate iron (as distinguished from iron powder used in powder metallurgy) as precipitants in place of tin cans, detinned scrap iron, or scrap iron is an intriguing possibility. The relatively faster copper precipitation rate obtained with particulate iron as compared to scrap iron promises economic and processing advantages when, and if, particulate iron becomes competitive cost-wise with available scrap iron. Kennecott has developed a precipitation cone,' see Fig. 1, utilizing various particulate iron precipitants and has demonstrated the process successfully in a prototype at a flow rate of approximately 1000 gal of solution per min. Essentially complete precipitation of copper is obtained, the cone overflow solution is clear and contains no particulate copper, and the iron factor is more favorable than in a conventional launder plant. Initially, sponge iron produced at the Ray Mines Div. Kennecott Copper Corp. for use in a Leach-Precipitation-Flotation process was used in exploratory tests to develop a suitable apparatus to take advantage of the rapid precipitation rate and efficient iron utilization for the recovery of copper from dilute solutions. Here it was demonstrated that, when sponge iron was added to a launder, the particles of iron collected in the bottom of the launder and tended to cement together. This resulted in incomplete precipitation of the copper and inefficient utilization of the iron. Next, sponge iron was suspended in glass columns to study the dynamics of the precipitation reaction. Again it was observed that the particles tended to cement together at low solution flow rates, while at higher flow rates large amounts of the precipitant overflowed the column, resulting in loss of precipitant and an inefficient process. Next, the precipitant was suspended in an inverted cone in a rising column of solution. Dynamic suspension of the solids was maintained at relatively rapid solution flow rates with instantaneous and complete precipitation of copper and with improved iron utilization. The first tests were conducted on a batch basis and it was determined that a dynamically suspended bed of precipitant was necessary for satisfactory operation. More than 99% of the metallic iron could be converted to metallic copper by careful control of the residence time in the cone and copper precipitation was essentially complete, even when the available iron precipitant was almost depleted. Several cones were built, ranging in capacity from 1 to 200 gal of feed solution per min, and finally, a prototype cone was constructed which was 20-ft high

Jan 1, 1968

By W. J. Carlson, S. M. Parmerter, I. Iwasaki

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates. It also deals with the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when an-ionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were affected most strongly by the level of starch, to a lesser degree by the pH, and virtually not at all by the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semitaconite could be readily attained with starch and calcium chloride. A previous article discussed some of the parameters that are important when various corn starches are applied to the soap flotation of activated silica from iron ores and to the flocculation of iron ore slimes.' Methods of solubilizing the starches and the molecular size after mechanical and thermal treatments, as inferred from the viscosity measurements, were shown to influence the adsorption characteristics on iron ores, and the residual concentrations of both calcium ion and starch in the pulp liquor were in direct correlation with the flotation and flocculation behavior.2-4 The present article summarizes the results of more recent tests conducted to ascertain the role of starches and starch derivatives in various phases of iron ore beneficiation. The scope of this investigation has been extended to include not only anionic and cationic flotation, but also the flocculation and filtration of iron oxide slimes, the selective flocculation and partial upgrading of semitaconites, and the flocculation and clarification of magnetite-taconite tailings —all problems that are of vital importance to the iron ore industry of Minnesota. By combining a practical approach with adsorption studies and by using single-mineral systems5 in these research efforts, it is believed that the ultimate goal of developing a suitable modification of starch structure may be realized. The topics covered in this article are limited to the empirical aspects of the research program on the depressant activity of starches and products in the cationic and anionic flotation of silica and of their role in flocculation, water clarification and filtration. ANIONIC SILICA FLOTATION In the soap flotation of activated silica from iron

Jan 1, 1970

By S. A. Ronlov

The importance of recognizing vibration problems during the plant design stage is emphasized in this paper. Often an experienced designer can recommend what type of support to use and how to tune the structure. However, obtaining sufficient information is a serious problem dealing with vibration. Vibration is a well known phenomena which, simply and generally, can be defined as a periodic motion. It is experienced in nature as caused by eerth- quake, wind, or ocean waves, and must be dealt with in the design of structure or ships. It must be realized that wherever there are moving or rotating elements, it is possible that unbalanced forces may induce vibration in the elements themselves, in adjacent parts, or in the supporting structure. Under certain circumstances, vibration will destroy machines or structures quickly and totally. The most widely known case is the total collapse of the Tacoma bridge when subjected to a wind of only 42 mph. Failures due to vibration of machines and/or their supports may occur in industrial plants where heavy equipment employed in the process must be supported and several machines are combined in close proximity. In the Metallurgical and Chemical Div. of The

Jan 1, 1962

By L. D. Lash, J. R. Ross

Discovery of scandium in the Vitro solvent extraction plant for uranium led to commercial recovery of the byproduct. Micro amounts of scandium were extracted with uranium by dodecyl phosphoric acid, but failed to follow ura-niuminto the hydrochloric acid strip solution and were eventually concentrated in the organic extractant. A fluoride strip system was developed to recover scandium from the solvent in concentrated form. High purity scandium oxide was then prepared in multi-pound lots by chemical separation techniques. The plant recovery operation, final product purification, and analytical procedures are described. Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per Ib which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth's crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the U. S. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold. Chemically, scandium is in group 3A of the periodic table. It is closely associated with yttrium and the rare earths which it strongly resembles in its reactions. It has a valence of three and will form an insoluble hydroxide, fluoride, or oxalate under proper conditions, similar to the rare earths. Eight years before its discovery, scandium was predicted by Mendeleef who ascribed his eka-boron with properties nearly identical to the actual properties of scandium. Its position as the element with Atomic No. 21 and Atomic Weight 44.96 places it between calcium and titanium in Period 4 of the chart. The successful commercial application of scandium must depend on unique properties to justify use of this high cost substance. Greater consumption would allow additional price reductions, but scan- dium will remain a relatively high-priced commodity because of its inherent scarcity. Research reportedly has been oriented toward use of scandium as an agent to achieve high-temperature, low-density alloys with magnesium and tantalum.' Also, the U.S. Air Force sponsored a project for production of research amounts of pure scandium metal.' The oxide has been used experimentally in electronics, ceramics, and metallurgy. The various aspects of scandium are well covered in recent publications.s-5 CONCENTRATE RECOVERY Small amounts of scandium exist in uranium ores and are dissolved during an acid leach yielding up to 0.001 gpl Sc2O9. When Vitro converted their uranium plant from phosphate precipitation to solvent extraction: scandium was found to follow the uranium into the dodecyl phosphoric acid solvent (DDPA). However, scandium did not strip with uranium from the DDPA in hydrochloric acid, but remained in the solvent. Therefore, a concentration of scandium built up in the organic phase. Residues from the solvent were spectrographed by the U.S. Bureau of Mines and found to contain scandium. As a result of this discovery, provisions were made in the plant for recovery of scandium-bearing concentrates. Solvent extraction of uranium was added to a conventional acid leach process in a typical installation? The ore was crushed and ground, and then leached with dilute sulfuric acid. Addition of an oxidant such as sodium chlorate insured conversion of uranium minerals to a soluble form. At this point, the slurry was chemically reduced by a sulfide, such as sodium hydrosulfide, to remove substances such as ferric iron and molybdenum which were partially extracted by the solvent. The solids-liquid separation was accomplished by a four-stage counter cur rent decantation (CCD) thickener circuit. The uranium was extracted from pregnant liquor with 0.1M DDPA in kerosene and stripped with ION

Jan 1, 1961

By D. R. Walker, M. C. Shaw

Dimitri Kececioglu (Allis-Chalmers Manufacturing Co., Milwaukee)—The idea of applying metal cutting theory to comminution and vice versa is very impressive. Among others, the demarcation of wheel-grinding data into two regions, namely Kick's and Rittinger's, draws attention here. A study of Figs. 6 to 9 shows the following: In Fig. 6, 1 point out of 8; in Fig. 7, 4 points out of 26; in Fig. 8 only 1 point out of 13; and in Fig. 9 practically none out of 13 points fall out of curve No. 2. Also when grinding particles smaller than 5x10." in. it is difficult to measure very accurately the grinding forces, chip geometry, and particle size. In view of the above it would be difficult to make a positive and distinct demarcation of the Wheel-grinding data into two regions, namely, Kick's and Rittinger's. The idea of using machine grinding to determine the comminution properties of materials is indeed unique. The following cautions come to mind, however, regarding applicability of machine grinding data to comminution: 1—Grinding gives uniform particle size, whereas comminution gives a variety of particle sizes in the same process. The fact that grinding gives uniform particle size is not necessarily an advantage because in comminution the overall energy under actual comminution is desired and comminution invariably results in the production of a variety of particle sizes. 2—In grinding, a small particle is ground off a comparatively large surface. In comminution small bodies are broken down to smaller bodies. This makes it difficult to establish a concept of reduction ratio in machine grinding. 3—The mechanics of machine grinding involve direct shearing action under very high strain and comparatively high compression at the shear zone, whereas: comminution involves direct dynamic compression and surface friction with comparatively little strain and shear. Consequently the mechanics of machine grinding appear to be different from those involved in comminution. Hence one might arrive at erroneous con- clusions when comminution characteristics are eval-uated from machine grinding results. It is noticed also that functions other 'than Eq. 16 which do not involve the concept of direct proportionality of useful energy input to new surface area created (Eq. 2 and particularly Eq. 12) may be derived to fit the, data of curve No. 2. One such relationship may be u = ct-", where c is a positive constant and n is a positive constant less than unity. This, of course, is made possible because data of a very small range. of particle size are being fitted by the curves of No. 2 and the hereby suggested relationship. A sound comminution theory should be applicable to a relatively large range of particle size. George B. Clark (Department of Mining Engineering, University of Illinois)—While the experimental work of Walker and Shawin this article is of intrinsic value in revealing certain fundamental aspects of machine grinding, milling, and related processes and in adding to the store of information concerning the comminution of solid materials by this particular process, it appears doubtful that the results of their research can be employed to verify either Kick's or Rittinger's theories. Both these laws were originally developed and proposed on the basis of very simple, idealized hypotheses. The creation of parallel idealized physical laboratory conditions which would be required for either their proof or disproof appear to be well beyond the scope of human ingenuity, at least at present. One great weakness of the imputed verification is that the spread of the points plotted on the graphs is not sufficient to permit accurate 'curve fitting. The range of particle sizes included in the belt and wheel grinding is not extensive enough to show any general trends, particularly for the horizontal portion of the curves, said to represent Kick's laws. That the milling; grinding, and turning data obtained by Walker and Shaw for both metals and minerals happen to comply with. certain interpretations of these two theories under certain specialized conditions

Jan 1, 1955

By B. K. Asdell

Crude kaolin exhibits a wide particle size range in which kaolinite is the predominant mineral. Bene-ficiation by wet processing produces high-brightness white pigments. The wet processing techniques peculiar to kaolin beneficiation are emphasized in this article in some detail. Included are discussions of long-distance pipeline transportation, centrifuga-tion, flotation, spray drying and shipment as 70% solids slurry. Georgia, a state seldom considered to be an important mineral producer, has one surprising feature — it is the nation's largest producer of kaolin. Kaolin is a highly important raw material in the paper, rubber, ceramic whiteware, paint and chemical industries. In 1965, more than 2.7 million tons of kaolin were produced in this state, a 150,000-ton increase over the preceding year, and production continues to climb. Strictly defined, the term "kaolin" applies to a group of hydrous aluminum silicates in which kaolinite is the predominant mineral. Kaolinite is inherently white, non-abrasive, chemically inert, and of a very fine particle size, ranging from sub-micron to 40-microns equivalent spherical diameter. An electron-micrograph of kaolinite is shown in Fig. 1. The particles finer than about 2 microns are thin, elongated plates, hexagonal in outline. The larger particles, coarser than 2 microns, are predominantly vermicular in outline with a foliated structure. Table I shows a typical chemical analysis of commercial, wet-processed kaolin compared to pure kaolinite. The sedimentary Cretaceous deposits of the Coastal Plain are the source of most of the kaolin produced in the Southeast. These deposits are of relatively high purity, and it is not uncommon to find the clays running greater than 90% kaolinite. Beneficiating plants using wet processing techniques are most numerous in an area within about 50 miles east of Macon, Ga., in a band approximately 15 miles wide. Kaolin may vary widely in quality from one deposit to another, or within the same deposit. The qualities critically examined are brightness index as measured by reflectance, viscosity of water suspensions, bleachability and particle size distribution. Crude kaolin always contains sand and mica in varying amounts, along with small amounts of many other minerals. These are classed collectively as "grit" because; they are generally coarser than 325

Jan 1, 1968

By W. V. Long, D. H. Reynolds, R. B. Bhappu

Equilibrium distribution coefficients were determined for some monovalent and polyvalent ions for several absorbing and exchanging media as functions of pH and initial ion concentration. Among ions studied were NH4 (I), K(I), Ni(II), Ce(III), Th(IV), and Mo(VI). Absorbents used were: ion exchange resins; a tertiary, and a quaternary amine in an inert solvent; and some activated carbons. The ions studied were in aqueous HCI, HNO3, H2SO4, or HC104 solutions. The classical mass action expression proved of little value in describing the variations observed. The data indicate that the determining factors in absorption and ion exchange may be the ionic species in the aqueous solution, which in turn depend upon pH, dilution, and perhaps other conditions. Three sorption processes have become prominent in recovering values from leach solutions. These are: 1) ion exchange, 2) solvent extraction (liquid ion exchange), and 3) physical adsorption by materials of high specific surface. In the first two of these processes the exchange reaction is considered chemical in nature, and is discussed in terms of the mass action principle. The third is considered a surface phenomenon and is discussed in terms of surface areas and various forms (Gouy, Stern, Grahame, etc.) of the Helmholtz double-layer theory. Generally speaking, we have found in chemical analysis and hydrometallurgical studies that there are close similarities between the three sorption processes, and also differences which are difficult to reconcile with any of the usual theoretical treatments. That others have experienced the same troubles is shown by the fact that usable processes, in chemical analysis as well as in hydrometallurgy, generally are discovered by empirical procedures. EXPERIMENTAL CONSlDERATlONS The gaps between theory and practice have allowed many conflicting statements to appear in the litera- ture. To learn, in particular, the behavior of some metallic ions on a cation exchange resin at a constant pH, equilibration studies were made over a wide range of concentrations.' Results are shown in Fig. 1 for four metals in hydrochloric acid solution on a strongly acidic cation exchange resin, AG 50W-X8 (Bio-Rad). The distribution coefficient, defined as D = amount of metal extracted per g of resin/amount of metal unextracted per ml of solution is seen to vary in a way to support all manner of reports about its behavior with changes in solution concentration. The metals used were chosen from those least likely to form stable chloro-complexes. The changes of slope in the various isotherms may reflect formation of unsuspected chloro-complexes of low stability (ion-pairing for example) whose concen-

Jan 1, 1967

By Fred C. Bond

SIX years have passed since the last grindability table was published.' In that time the list has been increased with many new tests, and the development of the new Third Theory of Comminution2 has made possible the reduction of all results to a consistent work index value. In this tabulation all grindability and crushability test results are given in terms of the work index, with formulas for reversion to the older units if desired. The average values for 57 different classes of materials are listed in Table I. The total number of work index values listed is 1211, and the overall average work index is 14.42. The complete tabulation, with each test listed alphabetically both under material type and under company name, can be obtained by writing to the Allis-Chalmers Manufacturing Co., Processing Machinery Department, Milwaukee 1, Wisconsin. The work index Wi is the calculated total work input in kilowatt-hours per short ton required to re- duce from theoretically infinite particle size to 80 pct passing 100 microns, or to approximately 67 pct passing 200 mesh. The work inputs required per ton for the same size reduction of different materials are directly proportional to their work indexes, and according to the Third Theory the work input per ton is inversely proportional to the square root of the diameter of the product particles. Where W represents the work input in kilowatt hours per ton, where F is the feed size, or diameter in microns of the square hole which 80 pct of the feed passes, P the product size, or microns which 80 pct of the product passes, and Rr the reduction ratio F/P, the work index Wi is found from Rr-l 100 When the work index Wi is known, the work input W required to reduce from any feed size F to any product size P is found from W = Wi ( Rr- 1 100

Jan 1, 1954

By J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and ferric iron concentration. The results have been discussed in terms of the adsorption of ferric cations and ferric hydroxide to the quartz surface. Possible relationships between the experimental results and the flotation of quartz have been examined. The adsorption of multivalent cations at the surface of quartz has been studied by many investigators who have used a variety of experimental techniques ranging from streaming potential 1 to radiometric2 measurements. Two possible mechanisms of cation activation of quartz have emerged from the results of these investigations viz: the adsorption of the cation to the negatively charged quartz surface, followed by adsorption of the collector anion to the adsorbed cation site, or: formation of a cation-collector complex which is then adsorbed to the quartz surface. In many natural and industrial systems one of the most prevalent activating species for quartz is ferric iron, this is especially so in the acid-circuit, anionic flotation of iron ore. The adsorption of ferric iron to the quartz surface is complicated by the ability of ferric iron to form complexes with anions, a phenomena which is of minor importance in one of the most widely studied quartz activation processes, ca ++ activation.* *The pK value for [ca(oH)+]/ [ca2+] [oh-] is 1.46 indicating that the influence of Ca (OH)+ ions will be minor in all but strongly alkaline solutions. In order to obtain a better understanding of quartz activation by ferric iron the zeta potential of quartz in the presence of ferric iron has been measured over a range of pH and ferric iron concentration. EXPERIMENTAL METHODS Materials: Selected samples of "rock clystal" quartz from New England, N.S.W., were ground in a pebble mill, washed for three hours in boiling concentrated hydrochloric acid, washed in hot chromic acid and then washed repeatedly with distilled water until the washing water gave no trace of chloride ion.

Jan 1, 1967

By R. T. O’Brien, J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and Ni (11) and Co (Ilj concentrations. Results have been discussed in terms of adsorption of Ni (11) and Co (11) cations and hydroxide precipitates. Possible relationships between the experimental results and the formation of lateritic nickel deposits have been discussed. The adsorption of metallic cations to the surface of silicate minerals is of significance in many industrial and natural processes. In an earlier publication,' the adsorption of Fe (111) to the quartz surface, a phenomenon of importance in flotation, was studied qualitatively using microelectrophoresis techniques. This paper reports the extension of this work to an investigation of the adsorption from aqueous solution of Co (11) and Ni (11) to the quartz surface. The adsorption of these metals was of interest for two reasons; firstly, the importance of such an adsorption process in the formation of nickel deposits by the lateritization of nickeliferous rocks, and secondly, the comparison of electrophoresis data for these metals, whose hydroxides precipitate in the pH range 7-8, with similar data for Fe (111) where the hydroxide first precipitates at pH 2.8. The development of laterites is essentially a near-surface geological process involving vertical and, in part, horizontal redistribution of elements derived from rock-forming minerals. This redistribution of elements leads to the formation of layers within the lateritic profile which are enriched in one or more of these elements and, depending on the nature of the original rocks, continued lateritization may give rise to iron ores, bauxites or nickeliferous laterites. The mechanisms discussed in this paper deal with the last mentioned type of deposit although the considered factors are applicable to laterites in general. Nickeliferous laterites are derived from basic and ultrabasic rocks containing ferro-magnesian silicates. These rocks may be partly or wholly converted to serpentinites. Besides their high Mg, Si and Fe contents, they also contain small amounts of Mn, Al, Cr, Ni, Co, Cu and Zn. The nickel content is usually near to 0.2-0.3%, but for economic use this must be increased during lateritization to over 1% and preferably over 2%. The zone of nickel enrichment is usually at some depth within the lateritic profile. Unpublished work by Mr. O'Brien on nickel-bearing laterites in eastern Australia indicated four visually different types of material which were separated from crushed samples under a stereo-microscope. Although chemical analyses indicated that all four types of fragments contained 2-4% nickel and smaller amounts of cobalt, X-ray diffraction and optical studies revealed only quartz, hematite and chromite as well as, in one of the types, a serpentine mineral. No distinct, nickeliferous minerals were detected. Furthermore, it was possible to extract some 60% of the nickel content of the laterites with cold 0.5N hydrochloric acid. It was therefore postulated that much of the contained nickel was present as amorphous, adsorbed material. In considering this fact, as well as the problem of the actual method of transfer and fixation of elements within the lateritic profile, it was further postulated that the transfer of these elements probably took place partly as solutions and partly as colloids and that the fixation of these was caused by adsorption and flocculation. The existence of nickel in solution in water draining from serpentinites has been confirmed by Smurov.2 Although we have no evidence for the transportation of nickel in the colloidal state, it is well accepted that colloids are important in the formation of laterites. Previous work by Mr. Mackenzie' has already indicated that iron may be adsorbed on quartz under conditions which could be expected in a lateritic profile, but no information was available for nickel or cobalt. Although adsorption possibly also takes place on minerals other than quartz, the latter is significant because silica is an important constituent of the silicate parent rocks. During lateritization, it is released to form free quartz and it is likely that it is initially extremely fine-grained. This would provide abundant opportunities for adsorption and it was de-

Jan 1, 1970

Jan 1, 1949

MINERALS BENEFICIATION DIVISION Established as a Division February 16, 1948 E. H. Crabtree, Jr, Chairman Donald W. Scott, Associate Chairman S D. Michaelson, Regional Vice-Chairman Will Mitchell, Jr., Regional Vice-Chairman William B Stephenson, Secretary-Treasurer Allen-Sherman-Hoff Pump Co 259 Lancaster Avenue Wynnewood, Pa. Raymond E. Byler, Past Chairman

Jan 1, 1952

Official Program

Jan 8, 1950

Established as a Division February 16, 1948 H Rush Spedden, Chairman Neil Plummer, Associate Chairman Stephen E Erickson, First Regional Vice-Chairman D A Dahlstrom, Second Regional Vice-Chairman Win T Marston, Secretary-Treasurer Dorr-Oliver, Inc 77 Havermeyer Lane Stamford, Connecticut

Jan 1, 1960

By F. F. Aplan

The past year has been another year of vigorous fundamental research in mineral processing as evidenced by the active publication of results, particularly in Germany, Japan, United Kingdom, United States and USSR. It was also noteworthy for several significant meetings and conferences. The Basic Science sessions at the AIME Annual Meeting continued to attract an increasing audience and the sessions were especially notable for the active discussion of papers. The third Engineering Foundation Conference on Particulate Matter Systems,1 chaired by F. F. Aplan, was held in Milwaukee in August and attracted over 100 experts from five continents. Sessions at this week-long conference covered comminution, particle characterization, separation of fine particles, fluid-solid separations as applied to pollution control, flotation kinetics, particle-particle interactions and particle agglomeration. This popular conference will be continued under John Karpinski of Bethlehem Steel Corp. as 1968 chairman.

Jan 2, 1968

By F. F. Aplan

Mineral processing engineers have recorded an- other year of active research and development work. Most gratifying was the broadly based attendance at the Mineral Processing Fundamental (formerly Basic Science) Committee sessions at the 1968 Annual Meeting of the AIME. Because of the availability of good papers, the active discussion and the growing attendance, sessions have grown from one to three at the annual meeting. Prof. M. C. Fuerstenau of the University of Utah will chair the Mineral Processing Fundamentals Committee for the next two years and we may thus be assured of continued active leadership. The name change from "Basic Science Committee" to the more descriptive "Mineral Processing Fundamentals Committee" approved by the MBD executive council is a welcome improvement. Our profession continues to attract the interest and cooperation of those in other professional groups. The 1968 Engineering Foundation Particulate Matter Conference, under the chairmanship of John Karpinski of Bethlehem Steel, was devoted exclusively to comminution this year. It attracted conferees from five continents and served as a particularly stimulating source of interchange of knowledge from many technical fields. Next year's conference will be under the chairmanship of Professor L,. G. Austin of The Pennsylvania State University. This conference plus the Symposium on Wettability and Flotation to be held at the annual American Chemical Society meeting in Minneapolis in April indicates the success achieved in the inter-disciplinary approach to problems. Other evidence of this spirit of professional cooperation is the forth- coming book on Size Reduction edited by D. W. Fuerstenau. This is the outgrowth of an AIChE symposium on size reduction held in 1965.

Jan 2, 1969

By S. J. Swainson

"It appears to me that the chief progress in milling operations in America have been made in the steady improvement of existing practice through both higher extractions and increased efficiencies of operations rather than by the development of new processes. The recent rapid development of sink-float, or heavy-medium separation, however, is an exception, and is becoming increasingly used to permit the economic treatment of certain low-grade ores that otherwise could not profitably be mined. The use of spirals and of small cyclones, both of which employ the principle of centrifugal force, show promise of increasing adoption through their application and efficiency in special cases." So did our distinguished colleague, O. A. E. Jackson, consulting metallurgist for the Union Corporation and president of the Chemical, Metallurgical and Mining Society of South Africa, summarize his impressions of a recent tour which he made of various metallurgical and milling plants in North America. I believe that all mineral dressers will agree with Dr. Jackson's concise conclusions.

Jan 1, 1950

By Donald A. Dahlstrom

In 1961 it became increasingly more evident that significant technological changes must be made in minerals beneficiation. The status quo in technology in today's competitive markets will not be tolerated. Higher productivity, greater recoveries and newer and better products must be sought and incorporated with lower operating costs. In other words, "when you build a new mill, don't build an old mill." Recommended reading for proof of the vital necessity of new methods and techniques is in the September 1961 issue of MINING ENGINEERING. The article by one of MBD's cherished and true veterans, E. H. Rose, is entitled "Iron Ore: The BIG Picture". Because of new beneficiation methods for iron ores, nearly 47 million tons of plus 60% iron concentrates will be produced and another 40.1 million tons of capacity will be under construction or committed. Thus in a relatively short period, 87 million tons of this high-grade iron concentrate with record low silica will be available. As Mr. Rose also points out, "in gross tons, without allowance for better grade, this is the equivalent of almost exactly two-thirds of all iron ore used for all purposes in the U.S. and Canada in the peak years of 1953 or 1957." Needless to say, improved mineral beneficiation methods have had far more reaching effects than just the production of higher grade iron concentrate.

Jan 2, 1962

In 1962, minerals beneficiation showed definite signs of coming out of the doldrums into which it has drifted after the uranium boom. Demand by steelmakers for high-grade iron pellets has created the need for concentrating plants to upgrade specular hematite by spiral concentration or flotation and magnetites by magnetic means and flotation. According to a paper given at the AMC annual meeting by C. S. Arms of Pickands Mather, "the shipment of pellets, started in the mid-1950's, has increased to 17.6 million tons in 1961 from North American operations. Many plants already underway will raise this production to about 42 million tons by 1965. This will be a very sizeable percentage of the total iron ore production contemplated by that date." Iron ore concentration methods are gradually raising the assay of pellets into the 65 to 69% Fe range and lowering silica to the 4 to 7% range. Quebec Cartier's Lac Jeannine concentrator went into operation in late 1961 and all grinding units were running by 1962. The Iron Ore Co. of Canada's new Carol Lake plant was started in mid-1962.

Jan 2, 1963