Search Documents

By William P. McConnell

At the dawning of the first century of AIME, mechanical handling of bulk materials was largely confined to movement of grain and light mill products by belt and screw conveyors, but grain handling experience inevitably led to the use of the belt conveyor for coal, ore and other heavier materials. In 1891, the first major U.S. conveyor installation for heavy minerals was completed at the Edison, N.J., plant of the New Jersey & Pennsylvania Concentrating Co. Functionally, this plant revealed its grain elevator heritage. Overlooked at the time of design or, perhaps more accurately, not fully recognized, were the dramatic differences between grain and minerals in both operating conditions of the system and the physical characteristics of the material to be conveyed. This inevitably caused problems, but from the ashes of these problems rose solutions. The Edison plant became a proving ground from which came two significant developments by Thomas Robins-the first conveyor belt designed specifically for impact loading and abrasive materials and the three-roll conveyor idler. As an installation with more than 50 conveyors in widths of 20-30 in. and belt centers of up to 500 ft, the plant was a landmark, for it established the belt conveyor as a vital method of trans- porting heavy, abrasive materials.

Jan 1, 1971

Diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for ventilation.

Jan 1, 1985

By Edward C. Mack, Ronald G. Stovash

INTRODUCTION Ronald G. Stovash General Superintendent Consolidation Coal Company Shoemaker Mine Moundsville, West Virginia Consolidation Coal Company's Shoemaker Mine is located in West Virginia's Northern panhandle near Wheeling, adjacent to the Ohio River. Steam coal is mined from the Pittsburgh #8 seam which averages 65 in. in thickness. The 10 in. of draw rock directly above the coal is taken on advancement, but remains when longwalled. The top consists of up to 12 in. of lower quality coal, and immediately over that, up to 10 ft of multi layered shales, coal, and bone. The cover ranges from 300 to 800 ft of shales and limestone. Two longwalls operate in the mine. The first longwall started in April 1975 and is retreating its eighth panel. This wall was the first to use shield supports in the United States. The second longwall started in September 1979 and is currently retreating its first 7,000 ft panel.

Jan 1, 1981

By T. E. Burke-Gaffney

SHERRIT Gordon Mines transplanted a 2000- ton mining plant and concentrator along with a town and its people 165 miles into undeveloped and almost inaccessible country in shifting its base of operations to the new mine at Lynn Lake. Faced with ultimate exhaustion of its ore bodies at Sherridon, Manitoba, the company, beginning in 1938, carried out an intensive program of prospecting and exploration in search of a new property. Late in 1945, diamond drilling of a magnetic anomaly near a minor surface expression of metallic sulphides gave promise of what has developed into the Lynn Lake nickel-copper deposit.

Jan 6, 1953

By Ian M. Thomson, Robert W. Greene

To move 7 million tons annually from their new inland coal mines at Camp Breckenridge, Ky., TVA selected a transportation package proposed by American Commercial Barge Line. The land portion includes two cable-driven conveyors covering 12.7 miles; a 260,000-ton storage area on a man-made island with a stacking-reclaiming bucket wheel; and a barge-loading system of 5500-tph capacity. The 183mile river portion will utilize three unit-tows with towboats and barges specially designed to carry the maximum tonnage allowed by locks and channel depth. The system has two noteworthy features. The first is a single-flight cable belt conveyor over nine miles long. The other is a high capacity twin belt conveyor using the principal of two separate belts supported in 60° troughing idlers. This conveyor exhibits a high carrying capacity combined with accurate tracking and lack of spillage. A description is given of the mechanical problems and solutions to the design, construction, and operation of the conveyor system which provides the link between the coal mine and the barge loading dock.

Jan 1, 1974

Herbert C. Hoover, who became a member of this Institute in 1896 and who is now one of its Vice-Presidents, is the man who in 1914 extended a helping hand to Americans stranded in Europe at the outbreak of the war, and who made it possible for many such travelers to return safely to their homes. When his countrymen no longer needed his services, he turned to the Belgians, whose need of food had been presented to him. Engineers have been among his assistants from the first, and it is because we believe that members of his own profession will still be particularly interested in his work that we thus mention it in the Bulletin. A Minute adopted by the Board of Directors of the Institute, in which the Belgian Kiddies, Ltd., is recommended to the consideration of the members, immediately follows the Proceedings of the Meeting of the Board of Directors. With the thought that members of the Institute may be glad to read Mr. Hoover's own words in regard to his work, we print in full the speech

Jan 3, 1917

By John Fritz

TROUGH it is not a condition of the Award, the fact is that the John Fritz Medal never has been given to an engineer who had not already received one or more similar awards. This "medal for medalists," on the evening of April 20, was presented to Daniel C. Jackling at a special dinner held at the Union League Club in New York. The citation read "For notable industrial achievement in initiating mass production of copper from low-grade ores through the application of engineering principles." The present award recognizes the same accomplishment-the launching and guiding to the port of marvelous success of the Utah Copper Co., first of the so-called "Porphyries"-as did the award of the William Lawrence Saunders Gold Medal by the A.I.M.E. in 1930, and before that the Award of the Gold Medal of the Mining and Metallurgical Society of America in 1926. Following the custom a biography of the Medalist had been published in a small pamphlet as a supplement to the John Fritz Medal Book. T. A. Rickard was the au¬thor of the sketch of Mr. Jackling, an innovation being the placing of a copy of the booklet at the place of each of the diners. The committee in charge of the dinner consisted of two past-presidents: R. E. Tally, of the A.I.M.E., who was chairman; Bancroft Gherardi, of the A.I.E.E.; and Thaddeus Merriman, director of the A. S. C. E., the John Fritz Medal being a joint award of the four societies. Frederick M. Becket, President of the A.I.M.E., as chairman for the occasion, briefly stated the purpose of the dinner. He stressed his satisfaction that the award was symbolic of the cooperative professional activities of the four great national organizations of engineers. He introduced Francis Lee Stuart, past-president of the A.S.C.E. and now chairman of the John Fritz Medal Board of Award. Mr. Stuart outlined the history and purpose of the Medal established in 1902 in memory of John Fritz, of Bethlehem, Pa., one of the great pioneers of America's iron and steel industry, metallurgist, and president of the A.I.M.E. in 1894. Mr. Stuart called the roll of former John Fritz Medalists, three of whom, Ralph Modjeski, J. Waldo Smith, and Ambrose Swasey, were present to do honor to Mr. Jackling. He then introduced George Otis Smith, whose privilege it was to present the Medalist for 1933. Dr. Smith was the senior of the four A.I.M.E. representatives on the Board that last year selected Mr. Jackling for the honor. His speech follows in full.

Jan 1, 1933

By Alex G. Sciulli

This paper discusses the primary computer programs used by the Mine Safety and Health Administration's Bruceton Safety Technology Center to evaluate coal refuse disposal plans. These programs are currently being used by private consultants, government, and the coal industry for today's coal refuse disposal problems. This paper outlines five programs, their special features, and their importance in the design and construction of coal refuse disposal facilities. The purpose of the paper is to present the general steps necessary in the computer-modeling of each program. The programs that are discussed include BISHOP, STABL, RWE, DAMS2, and HEC-2, which cover the subject areas of slope stability, hydrographs, flood routing, and water surface profiles.

Jan 1, 1983

By L. L. French

Jan 1, 1977

By Larry A. Shiprnan

DEMANDS upon power plants by the war program in 1941 intensified problems of coal utilization. It was an outstanding year in that field. The domestic heating stove witnessed outstanding development; the research folks progressing so rapidly that the design of the "perfect" stove is just around the corner. Use of colored motion pictures in analyzing fuel-bed performances has reached a new high with the colored pictures taken at minute intervals and projected at sixteen frames a second as shown by the Koppers Coal Co. and the Anthracite Institute (on domestic stokers) and the Consolidated Edison Co. (industrial stokers). Continued efforts of this kind will be beneficial in analyzing further some of the "Code for Testing Coal" problems confronting Subcommittee No. 2 of the Joint A. I. M. E. - A. S. M. E. Committees.

Jan 1, 1942

By M. W. Strong

THE technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in forma-tion, the type of problems met with, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differen-tial pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all mate-rials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improve-ment of material and its most efficient use has to be carried out. In this paper we propose to discuss the main mud problems with which we have to deal in Iran, some of which are peculiar to our local conditions while others are of the general type common to all workers in this subject.

Jan 1, 1938

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

By John V. Beall

Many Americans will judge the energy crisis by the picture shrink on their TV screen. And they are right to make this assessment considering the large areas of the country with marginal generating capacity, (See Fig, 1). The Federal Power Commission (FPC) recommends 20-25% reserve generating capacity above peak summer loads and 15-20% as minimal. The New York metropolitan area is the most concentrated power service area in the United States, and a spot check with Consolidated Edison, serving this area, revealed that on Friday, August 18, the company was operating at 5% reserve.

Jan 10, 1972

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

By J. M. Karpinski, F. P. White, R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball, the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corp.'s Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about 50% without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1972

By James F. McConnell, Charles W. Statler

Pennsylvania's existing large coal-fired units are limited to 2.0, 1.8, or 0.6 lb of sulfur per million Btu fired, depending on site location. Multi-stream coal preparation can be employed on system basis to extract the highest quality fraction of coal for use in units requiring the lowest sulfur. The middling fraction can be directed to units permitted higher sulfur. General Public Utilities Corp. has concluded that it is feasible to advance the state-of-the-art of heavy media coal preparation to produce an intensively cleaned primary product of 1.3 sp gr of less than 0.6 lb of sulfur per million Btu for the new unit and a middling product of 2.0 lb of sulfur per million Btu for existing units.

Jan 1, 1977

By A. H. Jones, J Leasia, S. J. Green, R. D. Perkins

Previously, two groups have conducted studies in order to define the influences of the intermediate principal stress. Mogi studied biaxial compression on prisms of Dunham dolomite and concluded that the intermediate principal stress should be taken into account. His study showed that failure strength increases with increasing [02], but less than the strength increase with increasing confining pressure. Handin, Heard, and Mogouirk's study on cylinders of Solenhofen limestone in torsion also found that the strength depends on the magnitude of [02]. More recent investigations by Mogi varying all three principal stresses independently and by Wawersik varying two of the principal stresses independently provide more detailed data confirming the effect of [02] on failure. All these tests were at low strain rates, and only the work of Wawersik reports measurement of all strains. The investigation here measures axial and transverse strains and included uniaxial and triaxial stress compression tests and biaxial stress tests using tubular samples (axial load and internal or external fluid pressure) at strain rates to 103/sec to provide the stress-strain response and to define the maximum stress or yield locus of Solenhofen limestone and Westerly granite.

Jan 1, 1971

Estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1986

By Rodolfo V. de la Cruz

The accurate assessment of the in situ deformability of rock masses is very important in the de and construction of underground openings for mining and geotechnical engineering applications. This paper presents a method and device for determining the in situ deformability of rock masses by relating the borehole jack load to the diametral displacements at a number of orientations around the borehole wall. The method called mu1tiple measurement method include the steps in which: a) diametral displacement sensors are installed at different orientations around the borehole to measure the changes in length of various diameters of the borehole; b) a uniaxial load is applied on two opposed octants of the borehole wall, and; c) using elastic theory and assuming a reasonable value for the Poisson's Ratio of the rock mass, the in situ deformability of the surrounding rock materials is determined from the measured diametral displacements and applied unidirectional load. The multiple measurement method has a significant advantage over existing methods since it provides several independent data in a single test from which to calculate the in situ deformability of the rock mass. The multiple data provide a check and counter check on the reliability and accuracy of the various measurements. The multiple data would also provide a means of quantifying the degree of fissuring on the borehole wall. Information on the degree of fissuring is very important in numerical modeling of rock masses.

Jan 1, 1984

By B. Ehgartner, M. Karmis, C. Haycocks

INTRODUCTION Interaction effects between mining operations developed on different levels of contiguously placed bedded deposits are a major problem in many parts of the United States. Efficient design criteria, derived from careful analysis of field studies as well as theoretical and model analysis, have shown that many problems that may result from seam interaction can be avoided, minimized, or on occasion used with beneficial results. Selection of seam mining sequence is rarely based only on ground control considerations, but rather on factors such as seam ownership, characteristics and accessibility. Therefore all possible mining sequences and methods must be considered in the development of multi-seam design criteria. Increased utilization of the longwall method of mining creates special problems in multi-seam mining due to the inevitability of caving and, therefore, subsidence. Considerable valuable experience has been gained in this direction from British mining operations where interaction problems are extremely common and the longwall method is the primary method used. However, limitations persist in the application of much of this information to U.S. conditions due to variation in layouts between advancing and retreating longwall systems and the inherent difference in the geologic environment. Considerable field data is available for U.S. room and pillar operations, and where successful pillaring operations have been carried out close parallels may be drawn with ground control mechanisms in longwall operations. VARIABLES AFFECTING INTERACTION Analysis of ground control multi-seam problems shows that factors contributing to interaction may be classified into variables that are fixed by the geo- logic environment and those that depend on engineering design. These may be described as follows (Haycocks et al, 1982): Fixed: (i) Depth*, (ii) Innerburden thickness*, (iii) Innerburden physical characteristics*, (iv) Stress field, (v) Seam thickness, (vi) Coal characteristics, (vii) Completed mining operations either above or below the seam to ve mined, and (viii) Age of workings. Mining: (i) Height, (ii) Dimensions and geometry*, (iii) Method*, and (iv) Spatial location of entries* *These variables are regarded as being critical effects. Few attempts have been made to quantify the variables controlling interaction. Dunham's (1978) linear regression analysis, combined with the National Coal Board's MRDE Roadway Monogram, is probably the most noteworthy. This study involved eighteen multi- seam longwall mines in the United Kingdom. The following variables were taken into account: seam depth, pillar width, opening shape, floor and roof conditions, rate of face advance, vertical seam interval, and age and geometry of overlying workings. A multi-linear regression analysis of these variables fitted by appropriate field values developed a prediction equation for lower seam stability. Although the study included many variables, it neglected the nature or geology of the innerburden. The prediction equation was found unreliable, but it did show the significance of geometry as a factor controlling lower seam stability. MINING SEQUENCES Irrespective of the type of mining method selected only four possible mining sequences are possible for two seams. Finlay and Winstanley wrote in 1934. .. "Experience has shown that whether the upper or lower seam was worked first, the subsequent working of the other seam in the same area seriously affected the roads in the seam first worked." Those effects depended upon the four basic mining sequences: 1) The upper seam is mined out prior to mining the underlying seam; i.e., the seams are mined sequentially downward and mining of the underlying seam is not commenced until operations above are completed and have ceased.

Jan 1, 1982