Search Documents

By T. F. Witherbee

Success in this operation is much promoted by adhering to a definite plan. Random work is of little account. In general, anything done that will enable the blast to pass through the obstruction, providing the melted products can be got away from the tuyeres, is all that is necessary. Hence the utility of high explosives in breaking up the chilled mass in the hearth. (This, by the way, should be done with the wind on, so as to prevent the filling of the tuyeres with the usual rush of cinder following the explosion.) If from any cause it is not expedient to use explosives, the simple but very effective instrument known as the kerosene or hydro-carbon blow-pipe can be depended upon to perforate the contents of a blastfurnace hearth to any extent required. It consists, as used in the Champlain district (first by Mr. Charles H. Foote), of several pieces of gas-pipe, liberally supplied with elbows (five in number) so as to be flexible; one end being connected to a tuyere-stock and the other brought to bear upon the place to be melted out. A 1/4-inch pipe leads from the last length, or blow-pipe proper, to a reservoir of kerosene or crude oil, set high enough to overcome the blast-pressure, This 1/4-inch pipe should have a valve conveniently located to regulate the flow of oil, and also another next to the reservoir. With a good hot blast and a surprisingly small quantity of oil, this apparatus will melt, burn or mechanically dislodge anything around a blast-furnace hearth excepting firebrick and water-cooled castings or plates. It may be helped by vigorous prodding with a suitable steel bar, to detach the fused but sometimes sticky material. A very good way to operate on a chilled hearth with it, is to open up a hole from a cinder- or iron-notch to the nose of the most convenient tuyere and then make a blow-pipe of the tuyere by turning

Jan 1, 1885

By J. P. Witherow

The Clapp and Griffiths steel-process may be considered a pneumatic system, similar to the Bessemer, with the difference that the converter is fixed or non-tilting, and that the blast is introduced around the lower section of the converter instead of through its bottom. Mr. Griffiths was engineer-in-chief of the Gilchrist & Thomas basic dephosphorizing process during all the time those gentlemen were experimenting and working up their system, as Mr. G. communicated to me. After separating from these gentlemen, he began developing the present Clapp and Griffiths type of converter. Dr. Clapp, of Nantyglow, Monmouthshire, was a prominent physician in a large iron district. Previous to his association with Mr. Griffiths, he took out some patents on a process of his own for the manufacture of steel, which patents stood in Mr. Griffiths' way; hence the consolidation. Early in the summer of 1883, my attention was called to the experiments of Messrs. Clapp & Griffiths in Great Britain by a friend who had just returned from England. Later in that summer I went to Newport, on the border of Wales, where I met Messrs. Clapp and Griffiths and their friends. After visiting two small converters of their type which were in operation at different works, and spending a few days in the iron-districts of Wales, I went to London, where I met my friend Henry W. Oliver, Jr., who had already heard of the new steel-process. We decided to revisit Wales and examine more fully the process, more especially that Mr. Oliver might have the opportunity of coming practically in contact with the men and die process himself, so that his judgment might not be influenced by my sanguine feelings. On

Jan 1, 1885

By Robert W. Hunt

HAVING devoted considerable time to the investigation of the Clapp-Griffiths converter and the metal produced in it, it may perhaps be of interest to the Institute to learn the conclusions which I have formed. Of course, it is well known that the stationary converter of small size is the very oldest type of vessel used in the pneumatic process. Hence it will be only necessary to call your attention to the points which are special features of the Clapp-Griffiths. This converter has a slag tap-hole, situated at such a height in relation to the metal under treatment that, when the cinder is formed and boils up as the blow progresses, it can run off and thus be removed from contact with the iron, and will also be out of the way when the decarbonized metal is tapped into the casting ladle and the manganiferous alloy added. The manner of shutting off the blast, when the process is completed and the metal is being tapped, is another distinctive feature. The tuyeres are situated around the sides of the vessel, and enter the interior some little distance above the bottom; they are provided with plugs through the centers of which there are small openings. When the blow is completed, these plugs are forced forward into the outer orifices of the tuyeres, thus shutting off the blast, excepting the small quantity' entering through the passages named. While this is sufficient to keep the metal from running into the tuyeres, it reduces to the minimum the action of the blast while the metal is being tapped. Of course, this is of great importance, as in an ordinary stationary converter any delay in getting open the tap-hole means overblowing, and even while the first part of the charge is running out the oxidation is in frill force. Duplicate or movable bottoms are used, thus more than doubling the possible output of the plant. The pressure of' blast is quite light, never ex-

Jan 1, 1885

By Willard Ide Pierce

CONSIDERING the extent of the gold-fields of Nova Scotia, which occupy an area of 6000 to 7000 square miles, a few words as to the cost of extracting and reducing the ores may prove of interest. The veins are for the most part narrow, 4 to 12 inches being the usual width, while a 2-foot vein is considered a large one; but they offer many advantages, inasmuch as the ore is easily treated, wages are low, and machinery and supplies can be transported by water to within from 1 to 15 miles of the different mining districts. The Salmon River vein is a notable exception to the above rule as to width. It ranges from 4 to 20 feet in width. The Hall-Anderson of Fifteen-Mile Stream (where there are several veins) is another, which has proved to be from 3 to 4 feet in width. The ownership of all mining claims is retained by the Crown, but persons wishing to work them can lease as many unoccupied areas as they please for twenty-one years, with option of renewal, on the payment of two dollars for each area, and a royalty of 2 per cent. on all gold extracted. Each area consists of 150 Get along the lode and 250 feet across, upon which a certain amount of work must be done, which by recent law is reduced from one hundred to forty days' work for each area every year. Any person erecting in a district the first mill, having at least 8 stamps, and being at least 10 miles from any other mill, is entitled to a lease of 10 areas, free from advance-payment and from royalty, for twenty-one years. A record must be kept, and filed every quarter at the office of the Commissioner of Mines, of the total number of days' work done on the areas, and a monthly statement of the number of tons crushed, and the actual yield of gold. Gold-mining in Nova Scotia may be said to have commenced with the finding of a nugget of gold in a brook at Tangier in 1858. The following table, taken from the official report," gives the total yield

Jan 1, 1885

By Byron W. Cheever

In working up the process which I described at the Chicago Meeting, May, 1884 (p. 163 of the present volume), for the estimation of phosphorus in iron and steel, I employed samples of steel obtained from one works only, and of a given brand. Since then I have had frequent occasion to test the process on other steels, and find that it works equally well. But some steels present certain colors which may mislead the operator; and I therefore propose a slight change in the directions formerly given. On the second page of my paper, in the second paragraph, I would substitute the following modified directions: Place the flask under the hydrant, till the solution is perfectly cold ; then add, gradually, strong ammonia, with constant stirring, till the solution is changed into a pasty mass and the ammonia is in slight excess; then add cautiously HNO3 (1.40 specific gravity)

Jan 1, 1885

By R. W. Raymond

The idea of obtaining light from incandescent solids is not new; nor is it. new to make such bodies incandescent by holding them in a heating flame. But the successful combination of the right substance and form of the body to be heated with the right kind of flame and the right means of adjustment, has not, to my knowledge, been accomplished heretofore; and it seems to me that the matergas incandescent light of Mr. Otto Fahnehjelm of Sweden, in which these objects appear to have been secured, is destined to become both famous and useful. The first fact upon which this invention is based, is the intense

Jan 1, 1885

By James P. Kimball

Jan 1, 1885

By Henry C. Freeman

The writer spent the month of November last in the La Plata mountains, Colorado, and the material portion of his observations, so far as they may be of general interest, is here recorded. The La Plata mountains lie northwest of the town of Durango. The California mining district is co-extensive with the mountains. They appear on the map as an isolated group; but an examination on the ground shows that they are the continuation of the great

Jan 1, 1885

By Henry M. Howe

Preparing the Metals.—Ordinary silver wire was hard-drawn to No. 23 Brown and Sharp gauge; it was cut in two, and one piece was carefully annealed in the ordinary way. The wire was prepared by Messrs. Guild and Delano, jewelers, Boston. The Ansonia Brass and Copper Co., Ansonia, Conn., kindly furnished me with some hard-drawn copper wire No. 31, A. W. G., and some of the same wire after annealing in the ordinary way.

Jan 1, 1885

By John Fulton

Johnstown is the site of the extensive iron, steel, and wire-works of the Cambria Iron Company. It is situated at the western base of the Alleghany Mountain, 275 miles from Philadelphia, and 78 miles from Pittsburgh. The valley in which the town and its ironworks are located, has an average elevation of 1160 feet above tide water. Johnstown, in its main features, is a modified duplicate of Pittsburgh. It is located at the confluence of the Little Conemaugh and Stony Creek rivers, which, by their union, form the Conemaugh River, just as Pittsburgh is situated at the junction of the Allegheny and Monongahela rivers, which together make the Ohio River. The site of Johnstown is in a cutting through the lower productive coal measures, 500 c feet deep, with steep slopes along the valleylimits, exposing, in sharp-cut terraces, the outcrops of the coal and iron-ore beds; the whole surmounted by the shales and sandstones of the barren measures.

Jan 1, 1885

By W. J. Taylor

FURNACE-MEN who have not taken advantage of the use of dynamite in certain blast-furnace troubles, as explained by Mr. Witherbee in his valuable papers read before the Institute some years since, cannot appreciate the quick relief and great advantage that may be derived at times from its judicious employment. Before giving my experience in the use of high explosives in blastfurnace troubles of certain kinds, I will record a method I have used with marked success in " blowing down." Had I not understood, however, the use of powder, I would have " salamandered " effectually the first time I tried it. Early in my straight-furnace experiments, last summer, at the Chester, N. J., Furnace, I wanted to blow down to within 3 or 4 feet of the tuyeres. To do this with a down-comer not lined, and without putting in any limestone to keep the gases cool enough to do no harm, was not an easy task. We could keep the bell and hopper cool by filling them with water, say 12 inches deep; but before we got the stock down 15 or 20 feet the pyrometer in the gas-flue on top mas up to 1300°, and the clowncomer was red-hot, with the heat still rising. In this emergency my assistant, Mr. N. M. Langdon, urged the trial of a plan lie had often advocated, viz., the introduction of water in some way under the bell in the proper quantity, in order that its evaporation might absorb and reduce the heat of the escaping gases to a point where it would not do any harm. He thought the bell

Jan 1, 1885

By William F. Blake

In September I contributed an article upon Columbite in the Black Hills of Dakota to the American Journal of Science. I had not at that time seen the paper by Professor Charles A. Schaeffer, of Cornell University, upon the occurrence of tautalite in the same region," or I would have gladly made reference to it. His analysis, proving the entire thence of columbic acid, shows that the specimen he analyzed, at least, should be called tantalite, and not columbite, if the distinction between these two closely related species is to be maintained. It is hard to say where the line is to be drawn, in such cases, between two minerals, when the specific characters and the composition are so nearly the same. If the name is to be determined by the relative amounts of tantalic and columbic acids, what shall we call the mineral when these acids are present in nearly equal quantities? Preference was given in this case to the name columbite, for the reason that the specific gravity, as ascertained by the ordinary scales at command, was nearer 6 than 7. As Professor Schaeffer had only one fragment by post, while I had an abundance from many places, it may yet be found that columbic acid predominates in some of the specimens. I therefore use the name columbite or tantalite indifferently. With this explanation I proceed to give a few observations upon the occurrence of the mineral with the tin-ore of the Black Hills. There are two localities, especially, where the mineral is found in the same dike or vein as the cassiterite: 1. at the Etta mine; 2. at the Bob Ingersoll claim. At the Etta it occurs in close association with albite and feldspar in crystals from one to four or five inches broad, and from one-quarter of an inch to three inches thick. It is not in contact with or mingled with the cassiterite, and each call be

Jan 1, 1885

By William F. Blake

The discovery of tin-ore in the Black Hills of Dakota dates from June, 1883, and short preliminary notices were published in September of that year.* The discovery-point is known as the Etta Mine, in the central portion of the Hills, about six miles east of

Jan 1, 1885

Rooms With Bath Rooms Without Bath Name Location Double Single Double Single Astor Times Square, 43d St. and $5.00 up $4.00 up $4.00 $2.50 up Broadway Belmont 42d St. and Park Ave. 6.00 up 5.00 tip 5.00 3.00 up Breslin 29th St. and Broadway 5.00 up 2.50 up 4.00 up 2.00 up Hermitage 42c1 Street and Broadway 4.50 up 2.50 up 3.50 up 2.00 up Imperial 32d St. and Broadway 4.50 up 3.00 up 3.50 up . 2.50 McAlpin 34th St. and Broadway 4.00 up 3.00 up 3.50 up 2.50 up Manhattan 42d St. and, Madison Ave. 6.00 tip 4.00 up 4.50 up 3.00 up Martinique 32d St. and Broadway 4.00 up 3.00 up 3.00 up 2.00 up Monticello 35 West 64th St. 2.50 up 2.00 up Navarre 38th St. and Seventh Ave 3.00 up 1.50 up 2.50 tip 1.50 up Plaza 58th St. and Fifth Ave. 6.00 up 4.00 up, Prince George.... 28th St. anti Fifth Ave. 3.00 up 2.00 up York 36th St. and Seventh Ave. 3.50 2.50 up 2.50 1.50

Jan 1, 1919

Executive Committee. GEORGE F. KUNZ, Chairman. E. GIBBON SPILSBURY, Vice-Chairman. THOMAS ROBINS, H. J. SEAMAN. Louis D. HUNTOON, Secretary-Treasurer. Meeting, Apr. 4, 1913. A joint meeting of the New York Section of the American Institute of Mining Engineers, the American Society of Mechanical Engineers, and the American Institute of Electrical Engineers was held in the large auditorium of the Engineering Societies Building, 29 West 39th Street, on Friday evening, Apr. 4, 1913, and an exhibition of the Edison Talking Moving Pictures was presented before the Societies, together with exhibitions of the work which is being done by the Edison Co. in making moving pictures to illustrate lectures on natural science and the useful arts for school and college work. Introductory remarks were made by Mr. J. W. Lieb, Jr., and followed by an exhibition of moving pictures illustrating the formation of crystals, the operation of different types of pumps, magnetic forces, electro-magnetic separation of iron ore, the evolution of the fly, and many other most interesting studies. One of the films, entitled The Formation of Crystals, showed a moving picture of a boy, whose laboratory was the kitchen, dissolving salt in a test tube filled with hot water. The boy then poured the solution of hot salt into a watch glass and placed it under the microscope to watch the crystals form. This film was immediately followed by another showing what the boy saw through the microscope. The solution at first was free from crystals. Gradually the crystals commenced to form and increased very rapidly after once starting, shooting across the screen with lightning speed. The film illustrating the separation of iron ores by the Edison electro-magnet showed an ore bin with an electro-magnet set at one side and below the bin. As the ore was dropped from the bin the magnetite was drawn into the. electric field and deposited in a separate rile from the sand.

Jan 5, 1913

The 112th Meeting of the Institute, and the Annual Business Meeting, will be held at the Headquarters of the Institute in New York City, Feb. 14 to 17, 1916. The Chairmen of several of the technical committees report that papers on subjects of timely interest in their respective branches have been promised. David H. Browne, who was appointed Chairman of the Committee on Arrangements, has organized his committee for active work. Members are urged to make their plans now to be present at this meeting to avail themselves of the pleasant opportunity for greeting old friends and making new ones among those engaged in the same profession.

Jan 12, 1915

THE Institute assembled in the rooms of the Geographical Society, Cooper Union, at 8 o'clock P.M., February 24th, 1874. President Barnard, of Columbia College, delivered an address of welcome, to which President Raymond responded. The Council then presented the following names, duly indorsed for election as members and associates. The gentlemen named were unanimously elected. *Bullock, M. C., - New York. †Burke, M. D., - Cincinnati, Ohio. *Burt, M. W., -Wheeling, W. Va. †Cameron, J. G. M., - New York. *Canfleld, Frederick A., - Dover, N. J. *Chandler, Prof. C. F., - New York. *Clayton, J. E., - Salt Lake City. †Colton, C. A., - New York. *Cooke, Prof. George H., - New Brunswick, N. J. *Cooper, Edward, - New York. *Dahlgren, C. B., - Mazatlan, Mexico. †Dutton, Capt. C. E., - Washington, D. C. *Eurich, E. F., - New York. †Fuller, H. L., - Woodside, Luzerne County, Pa. †Hamilton, S. Jr., - New York †Harnickell, A., - New York. *Hearne, F. J., - Wheeling, W. Va. *Hill, Samuel W., - Marshall, Mich. *Hulbert, Edward J., - Houghton, Mich. *Hunt, R. W., - Troy, N. Y. †lhlseng, M., - New York. *Iselin, Henri, - New York. *Janney, Morris P., - Pottstown, Pa. *Jenney, Frank B., - Brooklyn, N. Y. *Jenney, Walter P., - Brooklyn, N. Y. †Joy, D. A., - New York. *King, Clarence, - New York. *Kittoe, E. F., - Charleston, S. C. †Lawrence, Robert,. - New York. *Locke, J. M., - Cincinnati, Ohio. *McCormick, Henry, - Harrisburg, Pa. * Members. † Associates.

Jan 1, 1874

One Hundred and Twelfth Meeting of the Institute, Monday, February 14, to Thursday, February 17, inclusive, 1916 COMMITTEE ON ARRANGEMENTS DAVID H. BROWNE, Chairman. BRADLEY STOUGHTON, Vice-Chairman. LAWRENCE ADDICKS, BURR A. ROBINSON, P. E. BARBOUR, E. M. SHIPP, G. D. BARRON, JOSEPH STRUTHERS, J. V. N. DORR, E. B. STURGIS, J. R. FINLAY 'R. H. VAIL. L. D. HUNTOON, Hotel Accommodations.-The Committee on Arrangements is canvassing a number of hotels in New York City, securing .wherever possible special rates to members and guests for the clays of the meeting. It is possible to secure good accommodations on very reasonable terms in New York City if one knows where to look for them. A list of hotels and rates will be published in the final announcement of the meeting, which will go to the members about the middle of January, in order that those who desire to secure good hotel accommodations at a reasonable mice may have the information.

Jan 1, 1916

Full details of the program for the New York meeting .were given in the January Bulletin and the announcement mailed to members. The following brief synopsis is offered simply as a reminder of the principal events of this meeting which Chairman Browne says is going to be "different." Time.-Monday, Feb. 14, to Thursday, Feb. 17, 1916, inclusive. Place.-Engineering-Societies' Building, 29 West 39th St., New York. Events.-Monday, Tuesday and Wednesday (Morning and Afternoon) Technical Sessions. Tuesday, 10 a. m.: Annual Business Meeting, Luncheon served in the-Engineering Societies Building between sessions each day.

Jan 2, 1916

One Hundred Sixteenth Meeting of the Institute, Monday, Feb. 18, to Thursday, Feb. 21, inclusive, 1918 A preliminary program, for the New York Meeting was printed in the January Bulletin, and a more detailed program was mailed to all members early in January. The following schedule is the outcome, of sundry committee meetings up to the middle of January. Committee on Arrangements J.` E. JOHNSON, JR., Chairman BRADLEY STOUGHTON, Vice-Chairman RALPH W. DEACON MRS. S. J. JENNINGS E. M. SHIPP J. V. N. DOER A. R. LEDOUX G. D. VAN ARSDALE L. `V. FRANCIS . . F. T. RUBIDGE ARTHUR L. WALKER Summarized Program MONDAY, FEBRUARY 18 9 a. m. to 5. p. m. Registration at Institute Headquarters. 10 a. m. Sessions on Coal and Non-Ferrous Metallurgy. 12.30 p. m. Luncheon at Engineering Societies'. Building. 2 p. m. Visit to Subway Workings.

Jan 2, 1918