Search Documents

Thomas T. Read, New york, N. Y. (communication to the Secretary *):—At the meetings of English technical societies it not infrequently happens that, during the discussion of a paper, someone will arise to say that although he highly appreciated the material presented, nevertheless he believed it would have been better if some other phase of the question had been more highly emphasized. Assuming that this form of discussion is permissible in the Institute, I should like to reiterate the point made by Prof. A. J. Moses that conclusive proof of the identity of the minerals in question is an essential feature of the study of ores in this way. This is also expressed by Paul Krusch in his recent valuable paper on the sulphide ores (in which he arrives at conclusions diametrically opposed to those of Mr. Graton), as follows: "The diagnostic properties of the various ore minerals are known to but a limited circle of investigators." Many earlier investigators began the study of ores beneath the microscope by reflected light, but discontinued their work, in most cases, because they were unwilling to undertake the great amount of preliminary work necessary to securely establish a basis for their inferences. It is evident that Messrs. Graton and Murdoch realize that the promised later paper on diagnostic characters will be the more important of the two, but the point should be emphasized to forestall a flood of literature from other investigators who may gain the impression that the brief survey of polished specimens is a vade mecum to incontrovertible conclusions as to any given ore deposit.

Jan 1, 1914

Lucien Eaton, Ishpeming, Mich. (communication to the Secretary *):—I began to use water Leyner drills at the Cliffs Shaft mine at Ishpeming, Mich., over four years ago, and now have over 20 in use. The ore in this mine is hard specular hematite, and is mined by the room-and-pillar system, the rooms being driven as breast stopes. For many years only 3 1/4-in. piston drills were used in the mine, each machine ordinarily being able to drill from 15 to 25 ft. of holes in a shift. In the hardest ground, however, it was often, impossible to drill more than 2 or 3 ft. in a shift. When water Leyner drills were used the footage drilled was materially increased, especially in the hardest ground, but it was found that in very hard ground the breakage of machine parts, and especially of drill steel, was very high. At this time round steel with lugs forged on the shanks was used, and most of the breakage occurred at or near the lugs. Many experiments were made in an endeavor to overcome this breakage, and it was finally decided to do away with the lugs altogether, and use hexagonal steel. Accordingly I designed a chuck to use hexagonal steel without luge, a tappet being interposed between the hammer and the shank of the' drill steel. The design of this chuck of the proper size for the No. 18 Ingersoll-Leyner drill is shown in Fig. I. The different parts are also shown photographed in Fig. 2. A is the barrel of the chuck, which revolves inside the front head. It is made of machinery steel. B is the bushing which screws into the front end of the barrel A, and in which the drill steel fits loosely. This is turned down from a steel casting, the hexagonal hole being cast and then broached out to the proper size. It is case hardened inside. C is the tappet, which fits smoothly inside A just behind the bushing B. It is made of " N " temper Crescent tool steel and is carefully tempered. D is the tappet ring, which prevents the tappet from being pushed back too far by the

Jan 1, 1914

By H. M. Howe

§ 24. Introduction.—This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 614). The sections, tables, and illustrations are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894", but according to Meuthen it is at or below 770°, a discrepancy of 124" or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos. In Part 11. (§§ 29 to 39) I consider the chief causes of error. In Part III. (§§ 40 to 48) I apply certain corrections to some of the existing data, review those data, weight them, and calculate a prob-

Jan 1, 1914

E. W. Parker, Washington, D. C.: In connection with Mr. Blauvelt's paper, a brief sketch of the development of by-product coke-making in the United States may prove of interest. The first radical departure from the prevalent beehive oven to the by-product retort oven was inaugurated in 1891 by the Solvay Process Company, at Syracuse, N. Y. In that year was begun the construction of 12 Semet-Solvay ovens, which were completed in 1893. During 1893 these ovens produced 12,850 tons of coke, an average.of a little over 1000 tons each. In the following year the production amounted to 16,500 tons, not quite 1400 tons per oven. These 12 ovens were in reality an experiment, the success of which was attested by the addition to the same plant of 13 more ovens, begun in 1895 and completed in 1896. They were followed by the construction in 1896 of 25 ovens of the same type at Sharon, Pa., and 50 more at Dunbar, Pa. These 100 ovens represented the total number of Semet-Solvay ovens completed and in operation up to the close of 1897. The construction of 180 more, however—120 at Ensley, Ala., and 60 at Benwood, near Wheeling, W. Va.—was begun in 1897. The plant for the latter is laid out for double the number stated. The 60 ovens begun in 1897 have now been completed. An initial plant of Otto-Hoffman ovens was built at Johnstown, Pa., in 1895, and began making coke in 1896. One hundred and twenty additional ovens of this type were begun in 1896 and completed in 1897 at Glassport, near McKeesport, Pa. During the present year 100 Otto-Hoffman ovens are being added to the plant at Johnstown, and 400 of the same type are in course of construction at Everett, near Boston, Mass. The plant at the latter place is laid out for a total of 1200 ovens.

Jan 1, 1899

By Henry M. Howe

Henry M. Howe, Bedford Hills, N. Y. (communication to the Secretary.)*—Mr. Johnson's explanation, that the rounding of the graphite masses in oxygen-bearing cast iron is due to their being in part reprecipitated after re-solution in forming carbonic oxide temporarily with.that oxygen, is certainly most attractive and suggestive. It remains to be shown whether this rounding occurs also when the solidification is too rapid to permit this process to go on. J. E. Johnson might easily test this by casting a single ladleful of his oxygenated iron in masses of varying size. If this present hypothesis is true, then the rounding ought to increase progressively with the size of the casting, and with the distance from the outside, that is to say with the time available for re-solution and reprecipitation. I question whether a like benefit is to be expected even on this hypothesis, from the oxygenation of steel. The spheroidizing of graphite does good because graphite itself is so weak. But the constituent which can be spheroidized in steel is its cementite, which is a source of strength. Lamellar pearlite, in which this cementite in effect forms long den-drites, is far stronger than divorced pearlite, in which these dendrites have been broken up into spheroids. Even the surfaces of contact between ferrite and cementite are probably sources of strength because of the amorphous iron which probably fills them.

Jan 1, 1917

Discussion of the paper of K. Huessener, (Trans., vol. 53, pp. 402 to 4333, and of the papers of Linn Bradley, H. D. EGbert and W. W. Strong, pp. 303, 319. R. J. WysoR, So. Bethlehem, Pa. (communication to the Secretary*). —At our plant (Bethlehem Steel Co.), we have had several Bradshaw burners under course of construction and erection for some time, but up to the present we have not had opportunity to put them in service. I regret that I can not take part in the discussion with some actual results from these burners. Mr. Huessener properly emphasizes the importance of obtaining the highest combustion temperature practicable in boiler practice, which demands a near approach to perfect combustion conditions. The ideal burner is the one which, while meeting the various mechanical requirements, fulfills the above condition under a wide range of gas pressure. The question as to the relative value of hot raw gas and cold washed gas for boiler use is a very interesting one. I think that in the past the importance of low temperature of washed gas sometimes has been overemphasized. Mr. Huessener has pointed out that so far as temperature is concerned, no advantage accrues in washing gas below 100" F. In many plants, there is a notable operating economy in using furnace cooling water, which is appreciably warmer than the supply water. However, in a given type of washer, other conditions being constant, the lower the exit gas temperature the lower will be the dust content; this is equivalent to saying that the more washing water is used, other conditions being constant, the lower will be the dust content of the exit gas. For each type of washer there is a certain desired average temperature difference between inlet water and exit gas, concomitant with known average dust and moisture contents, and with economical operation. With the present tendency toward smaller stove checkers, it is generally agreed that gas for stove use should be cleaned to a dust content of 0.20 grain or less. The method employed and extent of gas cleaning are clearly problems for individual furnace plants. As a general proposition, wet washing is decidedly more attractive for furnaces smelting soft, fine Lake ores than for those reducing chiefly hard, lumpy ores, such as the foreign and domestic magnetites. In the former case the average moisture content of the gas is probably 35 grains per cubic foot, the dust content is relatively high and the top temperature relatively low. In our plant, the ore mixtures consist almost exclusively of hard magnetites. The average dust content of the gas leaving the dust catcher will average only about 2 grains and the moisture about 12 grains per cubic foot, corresponding to saturation at about 83" F. The temperature is fully 100" F. higher

Jan 1, 1917

By Lawrence Veiller, D. Eppelsheimer

D. Eppelsheimer, * Middletown, Ohio.—The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them than one dissatisfied with his home and surroundings, which feeling

Jan 1, 1919

By J. D. A. Morrow

This discussion relates to the distribution of coal under the di , of the U. S. Fuel Administration beginning Apr. 1, 1918. At t' L a definite method of controlling and directing distribution was put int effect. Prior thereto, although some of the machinery utilized was in operation, especially in the few weeks immediately preceding' Apr. 1, distribution had not been effectively and comprehensively organized. The writer was called to the Fuel Administration by Dr. Garfield about the first of February, 1918, to assume general direction of the distribution of coal for the Fuel Administration, to develop the general plans, and to obtain practical men to assist in this work and in carrying through the program finally devised. A study of the situation and conferences with the Fuel Administrator and leading men in the business made it plain that it would be necessary to begin at the bottom, measure the undertaking, develop plans to meet the need thus shown, and build an organization to effect the distribution required. This work had to be done under war pressure in the midst of a bad coal shortage. The successful performance of such a task is always primarily a matter of putting competent men in the right places and giving them the power and opportunity to function properly together. In the Distribution Division of the U. S. Fuel Administration, the men who were chiefly responsible for whipping plans into practical form and then for carrying out these plans were A. W. Calloway, of Baltimore, President of the Davis Coal & Coke Co., who served as the Director of Bituminous Coal Distribution; S. Lovell Yerkes, of Birmingham, Alabama, Secretary of the Grider Coal Sales Agency, who assumed general charge of distribution while the new plans and organization were being perfected and then became the Assistant Director of Bituminous Coal Distribution; Warren S. Blauvelt, of Detroit, who was Director of Coke Distri. bution; A. S. Learoyd of New York, Director of Anthracite Distribution, in connection with the Anthracite Committee, consisting of Joseph P. Dickson, President of Dickson & Eddy, Chairman; S. D. Warriner, President of the Lehigh Coal & Navigation Co., and W. H. Richards,

Jan 1, 1920

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By H. E. Doerr

The writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to be that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities. Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and sir-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250" F. (1235" C). Approximately 1 min. was required to forge under the steam hammer to 1 1/4 in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders 1/2 in. (17.7 mm.) in diameter and 1/2 in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. NO information was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by the letters A, B, and C. While there is considerable difference in the individual determinations for a number of the specimens, the averages

Jan 1, 1920

By Arthur Knapp

NO oil territory in the world has been so rich in large producing wells, in a comparatively small area, as the Baku field. Particularly is this true of the Bibi Eibat field, which formerly produced millions of "poods " of " gusher," or as it is called in Russia, "fountain" oil. The Bibi Eibat and Balachany fields have been exhausted of gas and ruined by water, but ' the Surachany and Benegadi fields are still fountain territories and: many outlying districts that have only been prospected produce rich fountains. The method of controlling fountains, or gushers, is the result of growth, along with the Russian system of drilling, where large diameters and riveted casing have been in vogue. The screw casing is seldom used except to exclude water. Formerly the method of finishing wells and the condition of the casing at the top of the well would not permit the use of gates, manifolds, and connections as is standard elsewhere. The life of the flowing wells is very short, particularly those 10 in. (25 cm.) or more in diameter, which produce large quantities of sand and often flow for but a few days and are then a complete loss. More than 1,000,000 poods in 24 hr. have been claimed in several instances, but in no case was the flow for more than a few days. The oil sands of this district are free uncemented sands and vary in thickness from paper thin to a maximum of 10 ft. (3 m.). The sands are interlaid with strata of soft clay. In spite of this, the practice has been to drill into such sands and produce from the open hole without screen or liners. Sometimes the casing is set below the oil sand but in this case holes from 21/2 to 3 in. in diameter are drilled opposite the oil sand, which would not have the effect of a screen. Fig. 1 is an outline of the fountain shield ready for the control of a fountain. It is composed of an inner and an outer covering made from rough boards. The framework is made of rough round poles. When a light flow is expected, only the inner lining is built; and when the fountain comes in unexpectedly, it is often possible to build only the outer cover. The bridge is for the purpose of renewing the blocks as they become worn by the flow. The lower block, as here shown, is made of hardwood and is bolted to the crossbeams with brass bolts. The grain end is toward the flow. The upper block, as shown here, is made of cast steel and is also bolted to the crossbeam with brass bolts.

Jan 1, 1921

By W. L. Saunders

When work was begun in September, 1910, on the rock excavation for the foundation of the gigantic dam at Valhalla, N. Y., which is to convert Kensico lake into an important storage reservoir of the Catskill Aqueduct system, one of the first steps taken by the contractor, H. S. Kerbaugh, Inc., was the development of a quarry to supply the stone needed in the

Jan 1, 1915

By Ray W. Arms

DRY cleaning, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc. Air Stratification In all of the above groups of air separating devices, the same phenomena are found as exist in water concentrators; that is, free settling will be found in some and hindered settling in others, with a complex action on the reciprocating tables similar to the wet tables. The experimental value of the settling ratios of particles in air has never been determined but, following the formulas given in Richards'

Jan 1, 1924

By Linn Bradley, W. W. Strong, H. D. Egbert

Marked differences of opinion have been expressed by engineers interested in cleaning iron blast-furnace gases for use in hot-blast stoves and under boilers, in reference to the advantages of a hot-dry method over a cold-wet method. One point at issue involves the sensible heat energy in the moisture contained in the gas. Some advocates of the cold-wet methods claim that the condensation and resultant removal of the greater portion of this contained moisture by wet scrubbing, spraying or similar methods, results in a saving of some of this sensible heat energy, by reason of the fact that water vapor has a high capacity for sensible heat energy and may carry from the exit of a hot-blast stove, for example, more heat units than are sacrificed or lost when the gas is cleaned by this cold-wet method. Other advantages claimed for the latter method are: That gas burns more readily when it is free from moisture in any form; that because gas is made denser by cooling and removing the moisture it has a higher calorific value than hot gas carrying moisture; and that higher flame temperatures are obtained when the gas is cleaned by the cold-wet method. A search through the available literature fails to disclose any extensive calculations or records of conditions obtained in practice, bearing upon these phases of gas cleaning. This paper deals with these problems from the standpoint of the economy of using a gas of higher flame temperatures, of improved stove design, and of economy in the gas-cleaning department. Calculations have been made which show that by cleaning the gases by a cold-wet method the sensible heat energy of the blast-furnace gases is greatly reduced; and, in general, this loss of heat energy is far greater than that lost from the stoves or boilers due to the sensible heat capacity of the water vapor if carried away by the exit gases. By making use of the

Jan 1, 1917

By D. Harrington

One of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo.; their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies were made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to coöperate. While the coöperation of the mining companies is necessary, the companies are put to practically no expense other than supplying a guide to accompany the investigators underground, the length of time spent

Jan 1, 1922

By H. G. Moulton

The increasing scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth pressures, formulas are used in which the assumption is made that earth banks fail by sliding along the slope determined by the frictional resistance of the material. The line of failure and the resulting pressure is held to be dependent on the angle of repose, which is different for varying

Jan 1, 1920

By S. C. Herold

Considerable interest has been shown, during recent years, in the possibilities of developing oil fields in the South American Republics, now that the exhaustion of our present fields can be seen in the not very distant future. The demand for fuel 011 and its products has been increasing far more rapidly than our increment of production during the last few years. Increase of consumption has been largely curtailed by the lack of sufficient supply. The main factors that have contributed to our previous neglect of the southern fields have been as follows: (a) Lack of sufficient demand for the product. (b) Competition with producing fields, having large production, low cost, and better geographical position, such as Tampico, Mexico. (c) Greater interest in home fields with ready market at hand. (d) Our ignorance of southern economic and geologic conditions, due to the distance between those areas and our financial centers. (e) Economic conditions in the southern countries, necessitating high costs of exploration and exploitation of the fields. (f) Our lack of understanding of the business methods of the Latin-American. It must be borne in mind that the oil-development work done to the present time in South America has, with one exception,' been undertaken upon lands which possessed direct evidence of oil in seepages or asphaltic deposits, occurring either immediately upon the lands or in their close vicinity. The development of oil fields in South America is therefore in the pioneer stage. It is not at all improbable that "hidden fields" will be uncovered in future work, as has occurred notably in the mid-continental field of this country within recent years. Location The areas grouped as a unit under the title of North Argentine-Bolivian oil field extend in a narrow belt from the north-central part of

Jan 1, 1920

By John Carter Anderson

The theory of a zonal deposition of ores from ascending solutions which were differentiation products of a cooling magma, first propounded by Spurr,l in a measure explained by Lindgren,2 and recently re-emphasized by kemp,3 while perhaps accepted in principle by many mining geologists, so far has not been accepted as capable of practical application in the study and development of ore deposits. From his observations, the writer is convinced that there are laws governing the primary deposition of ores which, when properly worked out, will be of greatest economic value; and that the application of this knowledge to the development of new mines will mark an advance in the mining industry similar to that following the working out and application of the theory of secondary enriehiment. That there has been a tendency to a zonal distribution in the formation of ore deposits, by which the ores of one metal have been precipitated from tile mincralizing solutiolis at a greater distance from the source than those of another, cannot be disputed; and the nature of this zoning in a given deposit or district has been frequently described.4 But that a selection precipitation of the ores of two or more metals, other than lead and zinc, in successive zones may have taken place in a single deposit within limits economically possible of exploration is not generally recognized or admitted.

Jan 1, 1923

By John Carter Anderson

The theory of a zonal deposition of ores from ascending solutions which were differentiation products of a cooling magma, first propounded by Spurr,l in a measure explained by Lindgren,2 and recently re-emphasized by kemp,3 while perhaps accepted in principle by many mining geologists, so far has not been accepted as capable of practical application in the study and development of ore deposits. From his observations, the writer is convinced that there are laws governing the primary deposition of ores which, when properly worked out, will be of greatest economic value; and that the application of this knowledge to the development of new mines will mark an advance in the mining industry similar to that following the working out and application of the theory of secondary enriehiment. That there has been a tendency to a zonal distribution in the formation of ore deposits, by which the ores of one metal have been precipitated from tile mincralizing solutiolis at a greater distance from the source than those of another, cannot be disputed; and the nature of this zoning in a given deposit or district has been frequently described.4 But that a selection precipitation of the ores of two or more metals, other than lead and zinc, in successive zones may have taken place in a single deposit within limits economically possible of exploration is not generally recognized or admitted.

Jan 1, 1923

By C. L. Kinney

The rapid increase in the amount of steel produced by the basic open-hearth process is an index of its ability to produce high-grade steel from raw materials of the most, varied physical character and chemical analysis. This inherent adaptability of the process has resulted in a lack of care in the selection of raw materials, so that in far too many cases charges are used of a chemical and physical character not justified by local economic conditions. A practice, or series of practices, should be used that will result in the greatest economy for the plant as a whole; therefore, the operations of blast furnace and open hearth must be considered together. In this paper, an effort has been made to show those variations in both open-hearth practice and cost that follow changes in the analysis of the pig iron arid it may be said that the theoretical costs shown are worthy of careful study and consideration. Carbon, manganese, silicon, phosphorus, and sulfur constitute the principal metalloids in basic pig iron and play the leading role in the production of steel by the basic open-hearth process. The percentages of each of these metalloids, with the exception of carbon, is a variable that has its genesis in the economic relation of the blast-furnace plant to its ore and fuel supplies. As the amount of carbon in the iron is a saturation function of the temperature at which it is produced, the variation in the amount carried is, for any given locality and grade of iron, practically negligible and is so considered in the eight heats discussed in this paper. The melting and refining reactions in an open-hearth furnace, either acid or basic, are essentially oxidizing and vary greatly with the type and age of the furnace, as well as the character of the fuel employed. The outstanding characteristic of the basic process, and the one that explains its predominance over the acid, is its ability to form out of the lime charged and the phosphorus oxidized from the charge a stable

Jan 1, 1924