Search Documents

By A. D. Rich

THE term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by inti-

Jan 1, 1949

By Ray W. Amstutz

The shaft was drilled on US government land m the Piceance Creek basin and was funded by the US Bureau of Mines (USBM). It was drilled to 723 m to provide access to rich deposits of oil shale, nahcolite, and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual-string, reverse-air, jet-assist circulation methods were used. Drilling required eight months. Site preparation, running, and cementing the casing required another four months. A 2.44-m ID steel welded casing, 508 mm thick was installed and 2.7 kt of cement were slurried and pumped into the annulus.

Jan 1, 1982

By Paul R. Bluekamp

The Mather Mine property is composed of a 5.2 sq km (2 sq mile) area within the Cities of Ishpeming and Negaunee which are located in the Upper Peninsula of Michigan. Production in this mine started in 1943; it ran continuously until its closing in 1979, having produced slightly over 55 million tons of iron ore. This mine was a joint venture between several steel companies and The Cleveland- Cliffs Iron Company (CCI), with CCI being the fee holder and operator. For the first 17 years of operation, the ore was shipped in its natural state directly from the mine to the steel mill. By 1960, iron ore pellets were on the market and they proved so superior to the natural soft Mather ore that the latter became difficult to sell except for the coarser portions. It was decided to develop a pelletizing process for the Mather ore, and this was accomplished by 1965 when the first Mather pellets were produced. From this date, all but the coarse fraction of the Mather ore was shipped as pellets. The geological setting is that of a large east-west trending synclinorium which plunges to the west. The lowest member of this trough-like structure is, for the most part, a quartzite-like graywacke, the upper 20 m of which grades into a softer, fine grained slate. Lying conformably on this graywacke footwall member is an iron- formation member which is over 1,300 m in thickness. This iron-formation is cow posed of thin alternate bands of iron oxides and chert and is intruded by a number of diorite sills - some up to 122 rn (400 ft) in thickness. The north limb of this synclinorium dips at approximately 45' and bottoms out at about 1,000 m from surface in the central part of the mine. There are two sets of faults, many of which are intruded by diorite dikes, which trend east-west and southeast-northwest. Displacements are varied, reaching a maximum displacement of 243 m (800 ft). The ore is found lying directly on the slatey footwall and its position is largely controlled by the faults and dikes, with the bulk of the ore being on the upper side of these structures. The ore is composed of soft earthy hematite and martite with vertical thicknesses up to 122 m (400 ft) although the average thickness would be closer to 46 m (150 ft). The ore averaged 60% iron and 7% silica on a dried analysis. The Mather Mine is located on the north limb of the syncline and was worked from two shafts, the deepest of which. was 1,09 7 m. These two shafts are about 2 km apart and serviced a total of 8 working levels between them during the life of the mine. The level spacing was about 61 m (200 ft). The main haulageways were driven parallel to the ore/footwall contact in the hard cow petent graywacke wherever possible. On the lower levels, deeper into the footwall, naked development was common. This material graded into roof bolting ground towards the upper stratigraphic portion. As drifting progressed further into the upper stratigraphic portion of the footwall, progressively stronger steel sets had to be used. From the main haulageway, cross-cuts were turned into the orebody on 61 m (200 ft) centers and extended as far as needed to recover the ore available to that particular cross-cut. The main haulageways and cross-cuts were driven 3 m (10 ft) high, 3 m (10 ft) wide at the top and 4.6 m (15 ft) wide at the bottom. This configuration would accomodate a set composed of a 2.7 m (9 ft) cap on top of two 2.7 m (9 ft) legs angled out at 18'. A sill plate was used under each leg to prevent its sinking into the ore below. The type of steel used was dependent on the expected weight to be experienced. Sets were placed on 1.63 m (5 ft 4 in.) centers; however, in extremely heavy areas, it was sometimes necessary to install sets on 0.8 m (2 ft 8 in.) centers. On the top two levels (5th and 6th), the ore was considerably hard-er and was mined by sub-level stoping and long hole drilling. Very light steel sets were used in the main haulageways and cross-cuts and timber was used in the production drifts. Some con- crete production drifts were installed on 6th level, but proved to be uneconomical. However, as mining reached greater depths, the ore became softer and more massive, reaching its maximum vertical heights on 11th and 12th levels. On levels 7 through 10, yielding steel sets were used extensively in the slusher drifts. While they were satisfactory on 7th and 8th levels, their success diminished with depth and they were

Jan 1, 1981

By Philip B. Bucky

[ ]

Jan 1, 1942

By Philip B. Bucky

[CONTENTS t. How Does One Determine WhetherPAGE an ore Body Will Block-cave?R. W. Hughes13 Sherman R. Burdick 13 PAGER. T. Gallagher 14 Mark A. Smith 2 C. F. B. Price, Jr.14 Harry A. Leidich2Benjamin F. Tillson 14 McHenry Mosier2C. F. Jackson14,17 R. W. Hughes2R. Taborelli15 Sherman R. Burdick3Frank A. Ayer16 R. T. Gallagher 3Philip B. Bucky16 Benjamin F. Tillson 3Rollin Farminr6 Lucien Eaton 3J. L. G. Weysser15, 0,17 C. F. Jackson 3George S. Rice17 Philip B. Bucky32. How Does One Determine the Block4. What Determines the Procedure in Dimensions and the DevelopmentRemoving Caved Ore? Work Necessary to Make an OreHarry A. Leidich17 Body Cave?McHenry Mosier17,21 Mark A. Smith 5,7,() R. W. Hughes17 Harry A. Leidich6Sherman R. Burdick 18 McHenry Mosier6,7,12 R. T. Gallagher 18 R. W. Hughes6Mark A. Smith I8 Sherman R. Burdick 7Philip B. Bucky20, 21, 23 R. T. Gallagher 7C. F. B. Price, Jr20 Benjamin F. Tillson 7,11R. H. Bennett21 L. E. Young7C. F. Jackson 21, 23 Robert D. Hoffman8, 1 2Gerald Sherman 3 . 21 Gerald Sherman8Tell Ertl21 Philip B. Bucky10, 11, 12G. K. Foster 23 R. S. McClellan 12C. H. Shoemaker23 Tell Ertl 12 3. How Do the Forces Act and What Are5. What Are the Criteria for Determining the Stresses Developed in a Blockthe Efficiency of a Block-caving That Cause It to Block-cave?Operation? Mark A. Smith 12, ISHarry A. Leidich23 Harry A. Leidich13McHenry Mosier24 McHenry Mosier13R. W. Hughes24 Sherman R. Burdick 24 R. T. Gallagher 24]

Jan 1, 1942

By C. E. Schwab

A lead-zinc orebody, in fairly strong quartzite and with a dip of 35° to 60°, is block-caved by use of scrams in a stair-step pattern up the ore footwall. Scram linings to handle coarse muck and permit the use of folding scrapers are developed by the use of end-grain wooden blocks to reduce maintenance and keep operating cost to a minimum.

Jan 10, 1953

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

By Kenric C. Owen

INTRODUCTION Situated 23 miles east of Pretoria the Premier Mine started diamond production in 1903. Two years later it produced the largest diamond yet discovered, the 3 106 carat Cullinan stone. For the period to 1932 when the mine was closed down due to economic circumstances, open cast mining was practised using inclined rope haulage traction and by this time had produced 48.5 million carats of predominantly industrial quality diamonds from 148 million tons of ore. In 1945 it was decided to re-open the mine using underground mining methods. A system using long hole benching was devised (Hodgson and Sewel 1960). This system was later modified but still forms the basis for approximately fifty percent of production. Following the successful introduction of block caving on associated diamond mines in the Kimberley area (Gallagher and Loftus 1960) this mining method was introduced to the Premier Mine in the late 60's and now accounts for nearly 50% of production. This paper will discuss block caving at Premier Mine in the light of our experience and discussion will be directed to the main geological and structural features of the orebody and host rocks and the related constraints imposed on the mining methods. Reference is made to the long hole benching mining method for comparative purposes. GENERAL DESCRIPTION OF OPERATIONS The ore from the block caving and bench mining areas gravitates via ore passes to a twin haulage, 500m below surface. Electric 13 tonne locomotives, each hauling a train of 10 Granby type cars, deliver the ore to two 42" x 48" (1.06m x 1.22m) jaw crushers. The ore is reduced in size to minus 0.15m before being hoisted to the treatment plant on surface. Hoisting is done with 12.5 tonne bottom discharge skips in a five compartment rectangular shaft using two 3 240 H.P. semi automatic Ward Leonard winders. A small single drum service winder operates in the other compartment. Men and materials travel in a separate shaft in a 5,4m x 2,8m cage operated by a Koepi winder. These two shafts are also the main intake airways to the mine. The two main extraction fans capable of 250 m3/s at 3,2 kPa are situated on surface and are connected to the underground workings by an incline and a network of air passes and return airways. GEOLOGY Although there are numerous occurrences of kimberlite bodies in the district, the Premier Mine kimberlite pipe is the only economic orebody. It is roughly oval in shape with surface dimensions of 900m on the long axis and 450monthe short axis. The surface area is 320 000 m2. The kimberlite has intruded a massive body of felsite and norite which is intersected by a number of faults. The contact between the kimberlite and host rock is clear cut and dips inward at an average angle of 80°. Cutting across the pipe and the country rock is a 75 metre thick gabbro sill, the top of which intersects the pipe below the 347m level and dips at 15' to the north west. The kimberlite has been metamorphosed a distance of some 20m both above and below the sill contacts. Age measurements on biotite from the gabbro date the sill as 1 115 million years, thereby providing a minimum age of the pipe. (Pre Cambrian). All other pipes in South Africa are of Cretaceous age (60 million years). A simplified geological plan and section of the Premier Mine orebody is shown in Figure 1. It is thought that the kimberlite intruded in at least three distinct phases. The kimberlites of these different phases can be distinguished most easily by their characteristic colour. BROWN KIMBERLITE. This is the oldest kimberlite and forms a crescent shape in plan on the south eastern side of the pipe. In depth it increases in relative area. Although the brown kimberlite carries the highest diamond grade in terms of carats per ton all the various kimberlites in the Premier pipe are economic to mine.

Jan 1, 1981

BLOCK CAVING HAS BEEN DEVELOPED to a high degree of efficiency in the last two decades and more particularly since World War II. At the Jeffrey mine of Canadian Johns-Manville Co., in the Eastern Townships of Quebec, several innovations have increased production and decreased costs. Asbestos ore is produced at the rate of 10,000 tpd from an underground operation supplemented by a large open pit that has been mined since 1881. The orebody consists of asbestos veins in a fractured and serpentinized peridotite. Hardness and structural strength of rock vary from soft shear zones at one extreme to a small amount of hard granitic inclusions at the other. In general the ore is weak and deteriorates on exposure to air, so that it is difficult to maintain underground openings for any period of time. Permanent workings are lined with concrete and temporary ones are driven mini- mum size and supported with steel sets as required.

Jan 5, 1954

By David D. Rabb

Under the auspices of the Atomic Energy Commission, the Lawrence Radiation Laboratory of the University of California analyzed an experiment to provide information as to whether the chimney of broken rock produced by a deeply buried nuclear explosive could be "drawn" by conventional techniques. Since many low-grade disseminated ore-bodies occur in a granite media, the experiment took place in a granodiorite-quartz monzonite intrusive porphyry in the Nevada Test Site as a follow-up to the Department of Defense's Hardhat detonation in February 1962. For emplacement of the nuclear device, a 12 ¼ - in. pilot hole was reamed to a diameter of 44 in. and a depth of 950 ft in one pass using a Hughes multiple-cluster rotary bit. It was then cased to 36 in. ID. The center of the explosive device was located 938.85 ft below the collar. The yield of the device was predicted to be 5 kilotons, or an equivalent of 5000 tons of TNT; the yield was later confirmed by chemical means to be 5.4 kilotons.

Jan 3, 1964

By Peter I. Brooker

Elementary estimation methods in which blocks are assigned values according to a geometrical area of influence concept are investigated for a tabular deposit. This quantitative assessment of the estimation technique is made using Matheron's geostatistics which allows the variance of the error between actual block values and estimated values to be found once the semi-variogram is known. For the deposit in question it is shown that the elementary technique makes poor use of the available information. There is a 20% relative error associated with it, whereas by using the optimal technique of kriging this can be reduced to 9%. An infill drilling program, which might have been suggested on area of influence results, would reduce the estimation variance only marginally over that of the current campaign; the relative error being lowered to 6%. Thus the geostatistical analysis shows this would be an unnecessary expense. The accuracy of an earlier drilling stage is also studied and it is shown that with the information available at the earlier stage block values could have been known with a relative error of 13%. Drilling could have stopped then if this were reckoned a tolerable error level. These results are all obtained for blocks whose size is dictated by the mining engineer and is set at the current grid size. In the area of influence approach smaller blocks are considered as the grid becomes finer and a study of the accuracy of area of influence estimates and kriged estimates for differing block sizes is presented. Between drilling stages more information from which the semi- variogram is calculated becomes available. The sensitivity of the estimation to changes in the semi-variogram parameters between earlier and current drilling programs is investigated.

Jan 1, 1977

By George Rupp

THE Sunrise iron mine of The Colorado Fuel and Iron Corporation is in Platte County, Wyoming, about 110 miles north of Cheyenne. It is served by the company-owned Colorado and Wyoming Railway, which connects with the Chicago, Burlington and Quincy and the Colorado and Southern railways at Guernsey, Wyoming, a distance of 6 miles from the mine. The original Sunrise claims were staked mainly by United States Army officers and soldiers stationed at old Fort Laramie, because of small showings of copper in the Carboniferous limestones that form a horizontal capping overlying the Huronian iron ore. A small copper smelter was operated for about three years at Fairbanks, now an aban-doned town on the North Platte River. As many of the copper shafts and test pits near the present Sunrise mine were deepened, they pene-trated the capping and encountered iron. ore or gray sericitic schist, and were abandoned. Evidence of an early interest in iron ore was found when the Chicago claim was stripped for mining. A narrow, winding crevice was dis-covered, which led downward 20 ft. through the capping to the underlying soft red hematite, in which a room 10 by 14 by 7 ft. had been excavated. Stone hammers and wedges and a few rusted pieces of iron were found on the floor, and the evidence is conclusive that the excavation was used up to rather recent times by Sioux Indian medicine men, to provide war paint.

Jan 1, 1939

By George H. Rupp

THE Sunrise iron mine of The Colorado Fuel and Iron Corporation is in Platte County, Wyoming, about 110 miles north of Cheyenne. It is served by the company-owned Colorado and Wyoming Railway, which connects with the Chicago, Burlington and Quincy and the Colorado and Southern railways at Guernsey, Wyoming, a distance of 6 miles from the mine. The original Sunrise claims were staked mainly by United States Army officers and soldiers stationed at old Fort Laramie, because of small showings of copper in the Carboniferous limestones that form a horizontal capping overlying the Huronian iron ore. A small copper smelter was operated for about three years at Fairbanks, now an abandoned town on the North Platte River. As many of the copper shafts and test pits near the present Sunrise mine were deepened, they penetrated the capping and encountered iron ore or gray sericitic schist, and were abandoned. Evidence of an early interest in iron ore was found when the Chicago claim was stripped for mining. A narrow, winding crevice was discovered, which led downward 20 ft. through the capping to the underlying soft red hematite, in which a room 10 by 14 by 7 ft. had been excavated. Stone hammers and wedges and a few rusted pieces of iron were found on the floor, and the evidence is conclusive that the excavation was used up to rather recent times by Sioux Indian medicine men, to provide war paint. GEOLOGY AND ORE The Sunrise district is in the Hartville uplift, an anticlinal area in which pre-Cambrian rocks similar to those of the Black Hills and the Laramie Mountains are brought to the surface. The lowest part of the pre-Cambrian series exposed is a great thickness of pink, crystalline, Huronian dolomites with thin unstratified beds of schist and quartzite. The upper part of the series consists mostly of gray or green schists but includes a few lenticular beds of jasper and a banded iron formation con-

Jan 1, 1939

By Alfonso W. Ovalle, Héctor R. Albornoz

INTRODUCTION The El Teniente Mine of Codelco-Chi le has extracted 588 mil lion tons of ore in its 77 year history for a total copper output of 8.800.000 tons. The mine production has been obtained mainly by traditional block-caving where grizzlemen using a hand held lever send ore through long-raises to load trains. At present the mine is about to introduce mechanized block-caving using LHD equipment to extract the primary rock. This paper describes this method which will be tested starting next month by caving an 11.000 square meter block. THE PRIMARY ROCK PROBLEM The secondary enrichment sulfides of the El Teniente ore body have characteristics which makes a standard unmechanized block-caving practice very successful. In the 60's parts of blocks encountered primary ow in the Teniente 1 and Sub-13 levels which proved to be extremely hard to extract. These foretold the obstacles that arised in the central part of the Teniente 4 level. Preparation of a completely primary 8.100 square meter block started in 1970. Its undercutting was completed by the end of 1972 and by 1973 the problem of mining the primary rock was clearly visualized. The numbers below describe the difficulties in mining this block: -Long-hole drilling rate is 90 m (270 ft) per shift in secondary rock and 37 m (110 ft) in primary. - Undercutting which is completed in 9 shifts in secondary took 180 shifts in the primary block. - Average grizzlymen productivity in secondary is 250 tons per shift while in primary it is only 25-30 tons, both at 343 mm (13 1/2 in. ) grizzly opening. - Powder consumption for secondary blasting increased from 8 grams per ton in secondary to 84 in primary. - The protection pillar between the under- cutting and the production levels was 60% broken in primary while 20% is usual for secondary. - Extraction advanced 5 cm per day in primary while a 50 cm per day rate is the aver- age in secondary. This is the main reason that after 8 years this primary block has a 20% extraction. Secondary blocks take 1.5 to 3 years to complete their extraction. - 80% of the boulders in primary rock are larger than 343 m (13 1/2 in.) with 10-20 % of them larger than 3 meters. -Direct cost of production (preparation, undercutting, extraction and haulage), using the traditional block-caving design for secondary rock, increased 3.5 to 4 times when used in primary rock. The following indicators of Table 1 show the rock characteristics differences.

Jan 1, 1981

By R. T. Murrill

BLOCK-SIGNAL and dispatching systems have been in use on surface railways for years, but only recently have they been applied to underground mining conditions. Formerly, all ore was moved underground by hand tramming; the surface openings were numerous and fairly close to the ore being mined. As the tramming distances increased, animals were brought into service. Then came the locomotive, and since its introduction, haulage lines have gradually been reduced to fewer levels and to fewer surface openings until more than 20,000 tons are being handled daily on one level in some of the larger mines. Under the, se conditions many trains must use the same-tracks, and signal systems have become necessary. In some cases it has been found more advantageous to use train dispatchers than to install signal devices. The dispatcher may be simply a flagman at a busy point or he may have mechanical signals to operate at more distant points. At the inspiration mine, Inspira-tion, Ariz., the station is equipped with a switch-con-trol board, whereby the dispatcher throws electrically all track switches in a certain block, which gives him complete control over all trains passing through that block. In a few cases, dispatcher stations are established in connection with a signal system.

Jan 2, 1922

By E. von Maltitz

IN his highly interesting paper on "Piping and Segregation in Steel Ingots,"1 Prof. Howe emphasizes the effect of successive phases of internal pressure in the ingot in the evolution of gas, and the consequent formation of blow-holes. From his statements in other places, it may be inferred that he does not here intend to ignore the other variable factor, temperature, but rather to discuss this one more particularly. At all events, it is my purpose not to engage in controversy with Prof. Howe, but rather to contribute, towards the complete elucidation of this important subject which we all desire, my own views and experience. If, in doing so, I specially emphasize other factors than pressure, I need not be understood as denying what I do not think it necessary to discuss fully. Nor, in presenting my own original conclusions, need I be understood as claiming to be the first who ever reached or announced them. Many things are asserted or suggested upon inconclusive evidence; and to confirm such tentative propositions may be as valuable a service as to overthrow them. In the following passage, Prof. Howe adduces analogies, based upon the behavior of charcoal and of water, respectively, which seem to me questionable "In general, the. solvent power falls as the pressure falls ; and in general it rises as the temperature falls. Thus, to heat a solid, for instance charcoal, may expel part of its dissolved gas ; and a tumbler of water drawn cold from the faucet gradually evolves gas, as it stands and warms up on the sideboard." (p. 238.) Charcoal is a solid body, which has the property not only of absorbing gases in large quantities, but also of expelling the thus absorbed gases upon heating. A comparison between charcoal and iron as to the absorption of gases is scientifically not possible ; the gas-content of charcoal is partly due to the

Sep 1, 1907

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

By W. R. Ingalls

SOME months ago, I had occasion to make an investigation that introduced the subject of blue powder that is produced as a byproduct in zinc dis-tillation. Although every zinc smelter is aware that more or less blue powder production is inevitable and there is a common practice as regards the treatment of it, the specific and quantitative data respecting the subject were more imperfect than would have been expected. I had reports from eight important works. Some of the data were especially determined for my investigation. Speaking generally, there is a good deal of uniformity in the figures, all of which show that the blue powder product, bears a large proportion to the ore originally charged into the retorts; that a large proportion of the retort capacity is devoted to the redistillation of blue powder; and that of the spelter product of a furnace about 30 per cent. is derived from blue powder, i.e., it is zinc that has been distilled twice. The figures from the works are given in the following table:

Jan 4, 1922

Meeting, Mar. 28, 1913.-The following Committees were appointed : Library ; Membership; Precious and Base Metals ; Papers and Publications ; Economic Geology ; Iron and Steel ; Increase of Membership; Stocking Pamphlets and Publications; and the following representatives: Joint Conference Committee of the four National Engineering Societies; General Committee in Charge of the International Engineering Congress, 1915. Delegates were appointed to attend the International Geological Congress and the Fifth Conservation Congress. These appointments are listed on pp. xxxvii. to xxxix.

Jan 4, 1913

Meeting of May 22, 1914.-President Thayer. announced the appointment of the following Committee on Arrangements for the San Francisco meeting of 1915: Charles W. Merrill, Chairman; F. W. Bradley, Abbot A. Hanks, S. B. Christy, and H. C. Hoover. President Thayer announced the appointment of the following Committee on Organization for the Utah-Nevada Local Section: R. C. Gemmell, Chairman; C. D. Blood, Lafayette Hanchett, Ernest Gayford; Duncan MacVichie, and George W. Riter. The President of the Institute offered $100, to be known as the "President's Prize," to be used as prizes for the best papers submitted by members of the Affiliated Student Societies, to be divided as follows: First Prize, $50; Second Prize, $30; Third Prize, $20. A committee, consisting of J. F. Kemp, Chairman; W. L. Saunders, and T. T. Read, was appointed to report on the conditions to govern the award. The President announced the appointment of the Committee on Mining and Milling Methods, the personnel of which is shown on a subsequent page of this Bulletin. The following were appointed on the Advisory Committee to the U. S. Bureau of Standards, to represent the manufacture of the various non-ferrous metals as indicated: Copper, F. L. Antisell; Nickel, David H. Browne; Lead, H. O. Hofman; Aluminum, J. W. Richards; Zinc, G. C. Stone. It was voted to hold a meeting of the Institute under the auspices of, the Iron and Steel Committee, the Committee on Petroleum and Gas, and the Committee on Coal and Coke, in Pittsburg, Pa., Oct. 8, 9, and. 10, 1914.

Jan 7, 1914