Search Documents

By E. C. Pechin

At the September meeting of the Iron and Steel Institute of Great Britain, Mr. Charles Wood, of the Tees Iron-works, read an interesting paper on "Further Improvements in Blast-Furnace Hearths," which was followed by an animated and instructive discussion. If the durability of hearths and in-walls is a matter of interest in England, where furnaces stay in blast from eight to twenty years, it

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By C. W. Andrews

The various methods of by-product coke-manufacture have been quite thoroughly discussed in a number of papers recently published, and I think it would possibly be of interest and value to discuss the growth and probable future of the byproduct coke industry, rather than details of manufacture. The first by-product coke-plant in the United States, consisting of 12 ovens, was put in operation at Syracuse in January, 1893. This installation was followed by one at Johnstown, Pa., in 1895; one at Dunbar, in 1896, and one at Glassport, in 1897. The plant at Syracuse was primarily intended to supply the owners with ammonia for their alkali-works. At Glassport, for the first time, gas was sold for illuminating purposes, although it was mixed with water-gas to make it marketable. The New England Coke & Gas Co. started the plant in Boston in 1899, which was destined to change the whole trend of the establishment of by-product plants, since it manufactured for the first time illuminating-gas suitable for sale without enrichment. This was accomplished by dividing the gas on the battery into two portions. One portion, consisting of the richer part of the gas, was saved for sale, while the remaining, or leaner, portion was used in the battery. This idea was originated by Dr. Schniewind, of the United Coke & Gas Co. The coke was used for domestic, industrial, and locomotive fuel, as its sulphur-content was too high to make it suitable for use in the foundry. The successful operation of this plant led to the building of additional plants at points where the production of illuminating-gas could be sold to advantage and where there was a fair market for the coke-output. The following list of illuminating-gas plants in order of construction will give a good idea of the rapid growth of this method of combined gas- and coke-manufacture: Hamilton, Ohio; Detroit, Mich.; Camden, N. J.; Baltimore, Md.; Chester, Pa.; Milwaukee, Wis.; Duluth, Minn.; Geneva, N. Y.; Chicago, Ill.; Indianapolis, Ind. In addition to these there are now under construction plants at Muncie, Ind.; Joliet, Ill., and Waukegan, Ill., all of which will produce illuminating-gas and metallurgical coke.

Jan 1, 1913

By Godfrey T. Vivian

Very often important discoveries are made in one industry that may be used to advantage in another, but, owing to the rarity that men step out of one industry into another, these discoveries remain unknown outside of the trade or profession in which they are made. The present paper is written solely with the object of bringing to the notice of mining and metallurgical engineers a centrifugal ore-concentrator which eventually may have a great application. Ore- Grading. Fig. 1 represents the action which takes place when solids of different dimensions are stirred up in a box and allowed to settle as minerals of the same size but of different specific gravity. This principle is applied practically in grading china-clay and in enriching tin-slimes. In the latter case the slimes are stirred around in a tub with water and allowed to settle while at the same time the side of the tub is struck with a hammer. The colloidal slimes are then poured off and various slices taken off horizontally. The great drawback of this process is that the particles are deposited horizontally and all the colloids are lost. Fig. 2 represents the action in which the particles are deposited side by side. Here the drawback is the great length of the box needed in order to prevent excessive loss. The alternative to lengthening the box is to increase the force of gravity. Centrifugal force may be regarded practically as the force of gravity augmented. Fig. 3 illustrates the Gee centrifugal machine for grading ores. The drum, A, fitted with a box, B, is mounted on a shaft or spindle, C, the whole being suspended from a ball-bearing of special design at D, supported between girders, E. Rota-

Jan 1, 1913

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By H. F. Dawes

In China all minerals are, theoretically at least, the property of the Emperor, and the Imperial permission must be got from him for the privilege of working them. A direct tax is levied on this privilege, and by simple command, the Emperor can close a mine at any time. Occult geomantic influences are a large factor in determining the opening or the arbitrary closing of a mine. The location with reference to points of the compass, graves and natural objects, may be really or professedly considered as indicating that those influences are favorable or unfavorable. The consequence, is, of course, that for the authorization and encouragement of any considerable enterprise, friends' at court, practical politics, and more or less bribery, are required. As a result, most Chinese mining is illicit, and is carried on in a small way only. Often along a single vein, or over a small section of mining country, a few individuals obtain rights over all the openings, most probably by loaning money to the head-men of the operators and holding the mines as security for the debt. In such cases, perhaps, for better security, all the ore is reduced in the works established by the creditors, who also handle all silver produced..As the head-men are, for the most part, improvident, and the laws and customs for the collection of' debts are stringent and peculiar, the " officemen" or creditors acquire in time what is practically an ownership of

Jan 1, 1892

By S. Whinery

I am indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of

Jan 1, 1913

By John S. Alexander

The typical block coal of the Brazil (Indiana) District differs in chemical composition but little from the coking coals of Western Pennsylvania. The physical difference, however, is quite marked; the latter has a cuboid structure made up of bituminous particles lying against each other, so that under the action of heat fusion throughout the mass readily takes place, while block coal is formed of alternate layers of rich bituminous matter and a charcoal-like substance, which is not only very slow of combustion, but so retards the transmission of heat that agglutination is prevented, and the coal burns away layer by layer, retaining its form until consumed. This property permits the use of raw block coal in the furnace but theo-

By Frank Firmstone

In 1871, two furnaces at the Glendon Iron Works, which had been blown out on account of the "coal strike," were altered from the open-top plan with side flues for collecting the gas, to closed tops with cup and cone. In one furnace the suppression of the side flues permitted a considerable alteration in the profile, but in the other (No. 5) no change in this respect was made; the side flues were simply bricked up and new ones cut through the sides close to the top. This furnace was in blast over four years, and we can, therefore, form a pretty good idea of the effect of the alterations on the furnace process. The principal dimensions are; Height 72'; greatest diameter, 18'; diameter at tuyeres, 8'; diameter of top, 10'; diameter at stock line (point at which the top of the materials is kept), 11'; cubic contents, 11,900 cubic feet. The table below shows the average results for periods of twentysix weeks each. 1st, of the open-topped furnace; 2d, of the furnace with the first charger used, which was an ordinary cup and cone (diameter of cone 5' 2") 3d, with the charger used ever since, a " double " cone 7' 5" diameter outside, having a central opening 3' in diameter. The diagram (Plate 11) shows the daily variations, in the grade of the irons for the same periods.*

By Frank Firmstone

It is proposed to consider here only comparisons made between results obtained when the materials employed are precisely the same, two furnaces at the same works for example, or the same furnace under different conditions as respects temperature of blast, method of charging, etc. With this limitation, the most important point in the comparison is the amount of fuel consumed per ton of iron. This, in fact, is the only item in the prime cost of the iron which can properly be said to vary in consequence of changes in the furnace process; for of the other principal items, the ore used per ton of iron, and also the amount of fluxing material, will depend on its richness, which, under the assumed conditions, will be practically invariable when taken over any considerable period; the labor cost also, from its nature, should be very nearly constant when estimated on the ton of iron. Moreover, as it consists principally in handling and moving material, it is greatly affected by circumstances quite independent of

By Cyril S. Taylor, Junius D. Edwards

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Junius D. Edwards, Cyril S. Taylor

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By R. C. Canby

The American water-jacket furnace is the outgrowth of lead-smelting at Eureka, Nev., subsequently developed in Utah and Colorado. Early smelting in Virginia, New England, or the Missouri-Kansas-Illinois district seems to have had no direct influence in the development of this furnace. First Decade, 1870 to 1880. In 1870, the draft-furnace was used in Nevada, coincidentally with the first crude sandstone blast furnaces, which were 2 or 3 ft. sq., with Sturtevant fans or small Roots blowers, and sheet-iron or water-cooled tuyeres. Stetefeldt, Liebenau, Albert Arents, and 0. H. Hahn mere the early metallurgical leaders. Arents's siphon-tap and the re-establishment of the furnace-bosh mere the most important improvements of the decade. Second Decade, 1880 to 1890. At first there were ,many small local plants; but by the time Eureka had reached its maximum production of lead-ore, two custom works (the Eureka and the Richmond) were treating all the ore, the miners having learned the economy of smelting at larger and well-constructed plants. In the early eighties, most of the features of modern practice were already discernible at Salt Lake, Leadville, Denver, and Pueblo. The small square sandstone furnaces had been replaced by rectangular water-jacket furnaces, mostly 36 in. wide, and from 60 to 80 in. long at the tuyeres, which entered between cast-iron water-jackets. Subsequently, Franz Casin, at the Holden works, Denver, put the tuyeres in the middle of the jackets, and many other improvements were made by him and others, so that the cast-iron jacket became the favorite, until the possibility of

Jan 1, 1913

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Albert E. Greene

Processes for the removal of phosphorus from iron or steel are steadily assuming greater importance in view of the abundance of high-phosphorus iron-ore and the diminishing supply of pure ore. In the present methods of removing phosphorus by the basic open-hearth or basic Bessemer process, or even by electric processes, complete control over the metallurgical conditions is either impossible or has not yet been realized. The removal of phosphorus has so long been accomplished along certain well-defined lines, that when the electric furnace made its appearance metallurgists adhered to the same old reactions used in the older processes and failed to appreciate and take advantage of the new forces at their disposal. One object of the present paper is to set forth more clearly the metallurgical reactions by which phosphorus can be removed from iron, and to show the necessity of controlling the conditions, and particularly the temperature, by means other than combustion in the furnace-chamber. Invariably, the commercial removal of phosphorus has been accomplished by oxidation. The reactions involved in oxidation of phosphorus in general consist, first, of the formation of P2O5 and second, the combination of this oxide with lime, forming calcium phosphate, which latter is held in a slag high in iron oxide. In the present-used processes, the phosphorus is never removed without the assistance or presence of considerable quantities of iron oxide. The oxygen for removal of phosphorus in the basic open-hearth process comes largely through the medium of iron oxide and furnace-gases, but not

Jan 1, 1913

By A. B. Wood

In welding and metal working by electricity, two systems are in use,—the so-called. incandescent system, in which the material operated upon is traversed by currents of large volume and low electro-motive force, the current having a continuous metallic circuit during the welding operation, and the arc system, in which the electric arc is utilized. It is the purpose of the present paper to call attention to this last

Jan 1, 1892

By J. B. Nau

A short time ago some interesting experiments concerning a new steel-making process in the open-hearth furnace were made by the writer at the Croton magnetic mine, N. Y.

Jan 1, 1892

By George Ross Green

[In discussion of the paper of Mr. J. C. Bayles, read at the New York meeting of September, 1890, Trans., xix., p. 18.1 It is often so difficult to locate the causes of failures of machinery and apparatus which can be examined and studied at leisure, that it is not surprising that the causes of explosions should escape detection. Usually the explosion is the first evidence that anything is amiss, and the time for observing the conditions is necessarily brief. An incident in a welding-works near Essen, Germany, might be cited as exemplifying what trifling causes may lead to disaster, and how difficult, under the most favorable conditions, it may be to discover them. A blowing-engine was arranged with two suction-pipes at each end of the blowing-cylinder—one leading to the air, and the other to the gas-holder. Each pipe was provided with a valve, and all were so adjusted that the cylinder drew in gas and air in the proportions found most advantageous. The gases from the cylinder were carried directly to the furnace through suitable pipes, and while the cylinder was provided with relief-valves, every effort was made to prevent explosions, principally by compressing the gases to a point where the rate of efflux of the mixture was greater than the velocity of combustion, if the expression is here allowable. It was found that the apparatus would work satisfactorily for some time, and then the relative proportions of the mixture would change, and an explosion might have been the result. Experiments consuming days were made to discover a method of averting this danger, but they were unsuccessful, until it was observed that the change in the composition of the mixture of gas and air took place when the gasometer began to rise or fall—the back-pressure due to friction when the holder was rising or its absence when falling being sufficient to change the conditions. As soon as this was discovered,

Jan 1, 1892