Search Documents

By Tribhawan N. Srivastava

The Henderson Mine started production in 1976 utilizing a unique, push-pull, mine ventilation plan. As the mine expands in size, the mine ventilation requirements will increase and a more comprehensive system for maintaining ventilation will be needed. A computer simulation study was completed and has resulted in a revised, systematic, mine ventilation plan which is being implemented as mine development proceeds. Based on the computer simulation study, the new ventilation plan takes into account mining of the orebody simultaneously from both the 8100 and 7700 production levels. Present experience and empirical data indicate that volumes of air needed to adequately ventilate both production levels cannot be obtained utilizing the existing mine layout. The total volume of air needed for the mine excluding haulage tunnel will increase from 708 m3/s (1 500 000 cfm) to 1652 m3/s (3 500 000 cfm), thus a new No. 5 exhaust shaft and connecting drifts are being developed to expand the mine ventilation system to service both production levels. The original ventilation plan for the 7500 haulage level was to bring air from the No. 2 and No. 3 intake shafts and exhaust it through the 94X raise to the 8035 exhaust level and then through the No. 1 exhaust shaft to surface. Control of air volumes in loading drifts was initially planned to be achieved by air doors and air curtains. Air doors on the 7500 level require large cutouts, expensive installations and constant maintenance. The computer simulation study indicates that air- flow in the 7500-level production drifts can be con- trolled exclusively by air curtains which are less expensive to install and more effective in regulating airflows than air doors. Air from the 7500 level can be exhausted through a new raise to the new 7635 exhaust level and then through the new No. 5 exhaust shaft.

Jan 1, 1982

By Roy R. Weil, John A. Dziubek

This paper discusses the use of computer modeling, data manipulation, and mapping of three multi-seam coal properties in the Appalachian coal basin. Each case history represents a slightly different application of computer usage for estimation of reserves and planning surface mine sequencing. This practical use of computers demonstrates the suitability of data processing for normal evaluation of coal properties.

Jan 1, 1983

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

By C. Richard Tinsley

Non-ferrous econometric metal models available from consultants are reviewed for structure and computer access, using copper as an example The evolution of a computerized metals price forecasting system for a consumer of non-ferrous metals is outlined including front ends, bridge equations, and supporting databases. An empirical sensitivity analysis technique is described. A postscript discusses the subscription costs of these models.

Jan 1, 1977

By E. C. Wade, R. D. Valentine

This paper describes a computer applications engineering system and it's use to apply a thermal dryer fan motor in a coal preparation plant. The computer hardware and software systems are described to indicate the general approach taken and a specific case study is reviewed to show how computer power is brought to projects in the coal industry.

Jan 1, 1983

By G. Adel, J. Richard Lucas, C. Haycocks

This paper describes over sixteen computer programs developed at Virginia Polytechnic Institute and State University during the past twenty years to assist in the design of coal operations. Overall development concepts in the construction of the programs are outlined, commencing with those used in the exploration phase of mining and extending through economic analysis and into the design of specific engineering systems such as belt, rail and power networks, scheduling, rock mechanics problems and simulation of face systems. Summarized information is given for the use of the major programs including user restrictions, input data, typical output and industrial applications and case studies. Analysis has been made of the programs' applications by industry throughout the world. Such analysis is facilitating development of new programs as well as a refinement of existing ones. To date programs have been constructed in four categories: exploration, ground control, economic and simulation. Face production simulations are stochastic in nature and require the use of time study data obtained at sites underground. Future programming efforts currently under development are aimed at interactive programs for use with minicomputers and, where advantageous, with graphical displays.

Jan 1, 1983

By Keith G. Kirk, Lawrence E. Welborn, Patrick A. Ley

Over the past two years the Office of Surface Mining in conjunction with Energy & Minerals Technology Assessment, ENCORE Systems Inc., and Boeing Computer Services has developed the Economic Coal and Ore Reserve Estimation (ENCORE) Coal Seam Modeling System. This system is being used by OSM, certain states, and industry for mine planning and mine plan permit review. The ENCORE system enables the mining engineer to start at the reserve estimation stage of surface mine planning and continue through the entire mine planning process and into the permit preparation process. The ENCORE system enables the state and federal regulatory authorities to assess a given mining and reclamation plan permit application in a rapid and efficient manner and greatly speeds up the mine plan review and permitting process. The ENCORE system is user friendly and menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Data are input both through digitized map files and bore hole information files and stored in a data base that is an integral part of the ENCORE system. The system performs reserve estimation through standard polygon methods, least square methods, and geostatistical (kriging) techniques. Geostatistical routines permit rapid evaluation of coal and overburden quality and quantity. System outputs include drill hole sumnary and resource summary reports, cross sections, isopach maps, structure contour maps, premining topography maps, postmining topography maps, and three-dimensional perspective views. The maps can be displayed on a high-resolution, color graphics terminal or generated by a high quality plotter and are suitable for direct inclusion in the mining and reclamation pl an permit application. This paper gives detailed examples of ENCORE'S use together with example outputs.

Jan 1, 1983

By Thomas J. Menner

Jan 1, 1983

By Suzanne T. Mathis, J. C. Ferm, J. T. Berger, W. Horger

A system of core logging and computerized entry and retrieval is described which permits accurate and rapid logging of core, cuttings and geophysical records derived from exploration and development bore holes. The system is so constructed that older drilling records can also be utilized. Output consists of conventional computer print out and graphic logs with a variety of scales, symbols and formats. Such logs can be used in constructing rock profiles which are necessary in property assessment and mine development.

Jan 1, 1983

By K. B. McQuillin

The volume of data resulting from an intensive search for new coalfields necessitated the establishment of a computer based processing system for coalfield data. The development of this system over the past seven years is described, with particular reference to the problems encountered in both the design and operation of the data base.

Jan 1, 1977

By J. T. Cherry

A fundamental goal of the Plowshare Program is to predict crater dimensions when an explosive of known yield is buried at a given depth in a given medium. In this paper a technique is presented that seems to calculate adequately, from first principles, the mound and cavity growth that occur during nuclear and high-explosive cratering events. The technique features a standard, numerical approach to high- intensity stress-wave propagation coupled with a unique model of material behavior in brittle failure. A schematic of stress-wave propagation is presented in Fig. 1. The equation of motion provides a functional relation between the applied stress field and the resulting acceleration of each point in the medium. Accelerations, when allowed to act over a small time increment [A]t, produce new velocities, velocities produce displacements, displacements produce strains, and strains produce a new stress field. Time is incremented by [A]t, and the cycle is repeated. The time increment [A]t is determined by an independent stability condition which requires the increment to be smaller than the time necessary far a compressional wave to travel across the smallest zone. We assume that failure occurs in a brittle material when either the tensile strength or the maximum allowable strain energy of distortion is exceeded. When either of these two conditions is violated, the code uses the cracked equation of state to determine the stress. A preshot testing program is used to determine the consolidated and cracked equations of state. In situ properties to be determined by field logging are density and elastic velocity (compressional and shear ve-

Jan 1, 1967

By Bobby P. Faulkner

The Tennessee Copper Co.'s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By H. W. Smith

This paper presents a review of developments to date in computer control practice, based in large part on Canadian experience. The basic problem examined is that of stabilizing control; matters considered are control strategies, hardware and software aspects of system implementation, reliability, human factors, and economic results.

Jan 1, 1976

By A. J. Lynch, E. V. Manlapig, J. H. Fewings, D. J. McKee

Progress in the development of an automatic control system for the chalcopyrite flotation circuit at Mount Isa Mines Limited is discussed. Preliminary studies have shown that the operating grade/ recovery curve for a sulphide flotation circuit is established by rougher-scavenger behaviour and the operating point on that curve by cleaner-retreatment behaviour. The control strategy of the rougher-scavenger banks involved regulation of xanthate to maintain recovery and control of air to seek the optimum grade/recovery curve. Control of the cleaner circuit to maintain the correct operating point of the plant relative to the ore entering it will be by air. Pulp levels will be used as an additional controllable variable in due course. Sensing instruments include a “Courier” on-stream analyser and several mass flow metering systems each of which contains a magnetic flow meter and a gama gauge. Measurements of concentrate grades and recoveries are made as early as possible in the rougher bank so that a change in the ore entering the plant can be detected as soon as possible. Over a period of six months from initial control systems application, computer control of xanthate resulted in an overall reduction in consumption of 10%. Experimental work has indicated that improved metallurgical performance will result from the introduction of additional air and level control loops.

Jan 1, 1976

By K. C. Carriere

INTRODUCTION The purpose of this section is to introduce the reader to the concepts of computer control of grinding circuits, and to flag some of the opportunities to be encountered, but without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with computer hardware and software, and in particular with the grinding process. The paper is organized into four parts: a general commentary of the need for computer control of grinding, a discussion of the process considerations involved, a more detailed elaboration on the current state of applicable computer technology, and a case study indicating one approach towards such a project. A brief installation survey and references for further reading are also given. This section will primarily deal with supervisory computer applications. Direct Digital Control and microprocessor systems are generally used as replacements for analog controls and thus are not considered in depth. Many configurations of grinding circuits exist, necessitating certain assumptions. Since many new concentrators use an open circuited SAG mill feeding a closed circuit ball mill, this configuration is used as a model although the principles stated can be extrapolated to any circuit. Motivation The use of computers for industrial control has been one of the dreams of control engineers and operators alike for many years. The concept of a plant running at optimal conditions with minimal operator involvement is very attractive from economic and technical standpoints. Accomplishment of this goal has been a long struggle, but today likelihood of success of such a project is very high, considering the reliability of modern hardware and the sophistication of available software. The primary motivation of any control system must be economic, i.e. it must pay for itself and make money for the owner, directly or indirectly. In grinding control the benefits which can be expected include: a) Higher through-put b) More uniform product in particle size, density and volumetric flog: c) Reduced operating costs including media consumption, power consumption and liner wear

Jan 1, 1982

By Stephen R. Holsinger

During 1972, Asarco's Silver Bell Unit embarked upon a project to test a digital computer-controlled grinding circuit against the performance of its other five grinding lines. The planning, implementation, and subsequent outcome of that project has been previously reported in a paper by Pitts 1, et al. This paper will describe the solutions to major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines. Changes made in operating philosophy and methods during the expansion will also be discussed.

Jan 12, 1978

By Stephen R. Holsinger

During 1972, Asarco's Silver Bell Unit embarked upon a project to test a digital computer-controlled grinding circuit against the performance of its other five grinding lines. The planning, implementation, and subsequent outcome of that project has been previously reported in a paper by Pittsl, et al. This paper will describe the solutions to major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines. Changes made in operating philosophy and methods during the expansion will also be discussed.

Jan 1, 1979

By D. Hodouin, T. Gelpe

A digital simulator of classification and grinding circuits is used to evaluate the performance of various flowsheets. For a given flows he et configuration, unit process dimensions, and operating conditions, the simulator calculates the steady-state values of the process variables and determines the conditions that meet the required operation criteria for tonnage and product quality. Calculation examples are proposed for the design of wet and dry grinding circuits. The performance of different configurations of cement clinker and sulfide ore grinding flowsheets is evaluated and discussed.

Jan 1, 1986

By C. A. Sobotowski, J. Eagan

Computer programs applicable to coal mining have been available for some time, especially in the academic sector. However, the computer has not routinely been applied to actual mining operations. This paper discusses how a computer system was set up as an important tool in mining design and decision making. The project was completed within the allotted timeframe of two months by taking advantage of existing technology. Key points include the selection of programs to meet the specified needs of the project, conversion of the programs to be compatible with a computer of a different manufacture, simplification of the data entry process, development of procedures for using these programs, and an explanation of how the reports generated from the programs were used for mine planning and decision making.

Jan 1, 1983

By Frank T. Wheby

The cost of tunneling is highly sensitive to the rock characteristics through which the tunnel is to be driven. These characteristics affect in a major way the rates at which tunnels and shafts can be driven and the degree to which the openings must be supported to maintain them in a permanent stable condition. Tunnel and shaft design and cost criteria have been computerized, permitting estimates of tunnel-shaft systems to be made directly from inputs of rock mechanics characteristics and other data. Curves of quantities of steel, rock bolts, and other rock support items as related to tunnel size and rock quality designation are presented. An illustrative example of the use of the program in calculating the cost of a hypothetical tunnel system is included.

Jan 1, 1971