Search Documents

By D. J. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent papers. 1.2.3.1 In those papers references were also given to the work of Haigh in 1917.6 Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper .2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and nonferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

Jan 1, 1928

By C. E. Reinhard

A USEFUL accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the, merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols.

Jan 1, 1929

By AIME AIME

CORROSION of tanks, pipes and other equipment in the oil fields is becoming worse as the production of high- sulfur crudes in the Texas panhandle and west Texas areas increases. It has been estimated that .in certain fields of that State one tank out of every five has to be replaced every year because of the high sulfur content of the crude. One suggested method for combating tank corrosion is the use of .materials which have a high resistance to the corrosive action of hydrogen sulfide and high-sulfur crudes; aluminum is one of these materials. As a result, the United

Jan 1, 1929

Boundary and general corrosio~z rates for higkpurity alutninum were ~rzeasured irz 16 pct HC1 at sJmllow penetrations (< 25 p). The rates for several high-angle random tilt boundaries, several [001] synzmetrical tilt boundaries, a 54-deg [010] twist, and a 15-deg randorn tw~st boundary were one-fourth to one-third higher than that of the (001) surface used as reference. Boundary attack was slower for 23 and 37-deg [001] tilt boundaries and a 16-deg [010] twist boundary. The corrosion rate for a (111) surface was roughly om-third higher than for (001) and was thus about as high as the corrosion rate of the fastest boundaries. The boundary attack did ?lot appear to parallel the variatiorz of boundavy energy. The signvicance of the anisotropy of corrosion was discussed.

Jan 1, 1966

By C. L. Mantell

ALTHOUGH SO common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium., titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be, too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well. below the melting point, say at 110° C. for a half hour or for a few minutes at 150° C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin metal in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intercrystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moiré metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, which result from the method

Jan 1, 1929

By E. P. Polushkin, Henry L. Shuldener

THIS paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. PIPES EXAMINED The pipes were made by different manufacturers and their sizes range from ¾ in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often 100 to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is 100° to 160°F. WATER SUPPLIES The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table I are characterized by relatively low hardness, low alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1944

By G. Reinberg, C. D. Clarke

Most underground mining operations are dependent on pumping installations to keep the mine unwatered. The reliability of such installations is obviously of paramount importance. The volume of water to be handled is often considerable, and the total head is relatively high. In these cases, both capital cost and operating expense of the pumping installations will become significant factors in overall mining costs. To insure reliability and to keep efficiencies, and hence operating costs, within acceptable limits it goes without saying that mechanical maintenance of a mine pumping installation must receive scrupulous attention at all times. Large mine pumping installations today almost invariably use multistage centrifugal pumps, since positive-displacement units would not be economically competitive except under very unusual conditions of small volume combined with extremely high heads. Centrifugal pump maintenance, under ideal circumstances, would be confined to parts subject to normal running water, i.e., bearing surfaces, stuffing box packing, and shaft sleeves. Under adverse conditions, however, metal may be lost from the wetted surfaces of a pump by erosive or corrosive action of the pumped fluid, and maintenance costs can easily attain enormous proportions.

Aug 1, 1956

By E. A. G. Colls

Discusses corrosion in Trail chemical plants producing ammonia, sulphuric, nitric and phosphoric acids, ammonium phosphates, sulphate and nitrate, together with miscellaneous allied material problems and their solution using erosion or corrosion proof materials. Conclusion, that for work of this nature, most costly material may well be cheapest in the long run.

Jan 4, 1950

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

THE subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for 10 years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. I). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, nonmetallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to 100 mg. per sq. cm. per day, the corrosion rate of high-purity magnesium is 0.15 ± 0.05 mg. per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in combination, in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called "tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable. In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0.001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. While the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1941

By J. E. Pollock, W. R. Hicks, E. Camp

IN the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance, a substitution first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replacement with more costly material must be justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete. TEST METHODS Either one Of two methods or a combination of both, in the absence of reliable data in similar services, may be adopted to determine to what extent replacement with other, and perhaps more expensive, materials is justified. A unit may be constructed incorporating different metals or alloys so that comparative service may be obtained under the same service conditions; this has been applied in many instances, such as condenser and tank construction, but the opportunities for inspection may be few and

Jan 1, 1935

By J. E. Pollock

IN the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance; a substitu-tion first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replace-ment with more costly material must be. justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete.

Jan 1, 1935

By K. A. Natarajan, S. C. Riemer, I. Iwasaki

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration (nitrogen, air, and oxygen) on ball wear was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. Marked ball grinding tests and electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen toward wear (corrosive wear) is relatively small, and abrasive wear appears to be significant. Rheological properties of the slurry appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1985

Cortez Gold Mines operated a conventional 2,100 mtpd (2, 300 stpd) cyanidation plant until the 5 million ton ore body was worked out in 1973. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME 1975.) Sub-grade material was dump leached at the mine -mill location in 1971, and the resulting pregnant solutions were added to the feed in the plant&apos;s Merrill-Crowe precipitation unit for gold recovery. In early 1973, however, Cortez put into operation their Gold Acres mine which was located about 13 krn (8 miles) to the west of the &apos;Cortez mine. Economics at that time dictated the heap leaching of the lower grade portion of the ore body with the higher grade being trucked to the Cortez plant for milling. Leach ore was moved directly from the open pits to prepared leach pads located on a gently sloping terrain of 570 grade. Preliminary pad preparation at the leach site included removal of vegetation which was composed of sagebrush and grading of the base. Pads were comprised of mostly minus 74 micron (200 mesh) materials and were made of clay-silt or slime tailings spread on the pad area in thin 50 to 75 mm (2 to 3 in. ) layers, compacted with a vibrating roller compactor to a depth of about 380 mm (15 in.). This was followed with a 100 mrn (4 in.) layer of coarse rock to prevent erosion on the pad and to allow solutions to move laterally under the heaps. Leach solutions normally traveled the length of the heaps and were collected in plastic-lined ditches from which they flowed by gravity to the pregnant solution storage pond. Both pregnant and barren ponds were constructed in the same manner as the leach pads - being lined with compacted tailings or clay silts. The Gold Acres facility required pregnant solution storage of 6 million liters (1.6 million gal) and barren storage of 3.8 million liters (1.0 million gal) designed to handle two to three days of heap drainage or to retain run-off from a major rainfall. Various heap heights were tried including 3, 6, and 9 meters (10, 20, and 30 ft), with a 6 m (20 ft) height selected. Ore was dumped by trucks in a single 6 m (20 ft) lift using a D8 Caterpillar dozer for

Jan 1, 1981

By Ralph L. Erickson

The discovery of a Carlin-type gold deposit at Cortez, Nevada, in 1966 can be attributed directly to the use of geochemical exploration techniques. Most mineral deposits owe their discovery to geologic concepts, geologic analysis, and luck, but at Cortez, geochemistry as an exploration tool played the clearly dominant role in discovery. Of course, the economic significance of the discovery had to be determined by exploration and development drilling. The story of the discovery began in 1959 when field work was initiated on a new project, "Geochemical Halos Utah and Nevada," by R.L. Erickson and A. P. Marranzino for the US Geological Survey. The Cortez district was selected for geochemical work because it was an area with good geologic control where we could address the problem of how to prospect in barren outcrops for concealed ore deposits in potentially favorable structures (buried thrust zones) or favorable host rocks in the subsurface. Geologic mapping of the Cortez 15-min quadrangle, just being completed by Gilluly and Masursky (1965), showed that the quadrangle contained excellent exposures of both the upper and lower plates of the Roberts Mountains thrust fault, a major structural feature of north-central Nevada. Roberts (1960) had noted that a number of mining districts were associated with windows in the thrust. In 1959, Erickson and Marranzino did some reconnaissance rock sampling and spring-water sampling in the siliceous clastic rocks of the upper plate of the thrust. Results of this reconnaissance prompted a full-scale sampling program in 1960 in the upper plate rocks on the west flank of the Cortez window. Results of the investigation showed that anomalously high concentrations of metals occur in the upper plate rocks, and further, that the distribution of metals is fault controlled and shows a pronounced zoning pattern (central copper zone; intermediate zinc, copper, and lead zone; and outer arsenic zone). The anomalies were interpreted as primary leakage halos that originated from metal occurrences in the thrust zone or in carbonate rocks below the thrust and moved upward along normal faults that cut both upper and lower plate rocks. Erickson gave a talk about these anomalies in the summer of 1961 to the local AIME Section in Reno, Nevada; two short reports were published that year-" Geochemical Anomalies in the Upper Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1961) and "Hydrogeochemical Anomalies in Four Mile Canyon Near Cortez, Nevada" (Erickson and Marranzino, 1961). These releases prompted blanket staking in the area by several small companies. In 1963, geologic and geochemical mapping were started by the USGS in the lower plate carbonate rocks of the Cortez window west of the quartz monzonite stock at Mount Tenabo and north of the old townsite of Cortez. The results of the work showed anomalously high concentrations of arsenic, antimony, and tungsten in jasperoid, fracture filling, and shear zones in Silurian and Devonian carbonate rocks. The anomalous area was about 1.6 km (I mile) long and 300 m (1000 ft) wide. A brief report, "Geochemical Anomalies in the Lower Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1964a), was published in 1964. During this same time period, 1959-1964, several exploration or mining companies were active in the general area (chiefly mapping geology and acquiring property). In 1964, American Exploration and Mining Company (Amex) concluded that the entire Cortez district was worthy of an extensive exploration effort involving drilling as well as geologic, geophysical, and geochemical studies. To carry out the program, Amex formed a joint venture group with the Bunker Hill Company, Vernon Taylor, Jr., and Webb Resources. Their early efforts were directed to the upper plate rocks and to the lower levels of the old Cortez silver mine. The group also drilled some shallow rotary assessment holes adjacent to the area of the arsenic, antimony, tungsten anomaly in lower plate carbonate rocks described in Erickson et al. (1964a). Assay results from these holes offered little or no encouragement to the joint venture group. Splits of these drill samples were made available to the USGS. In order to enhance any metal content present in these rocks and to determine the mineral residence of any metals detected, heavy-mineral concentrates of each 3-m (10-ft) sam-

Jan 1, 1985

By Roland D. Parks

CORUNDUM, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to our allies. Optical elements of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mohs&apos; scale index of o, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent of this paper to deal only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. ORE PRODUCTION AND CONSUMPTION For the past two decades, South Africa has been the world&apos;s sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world&apos;s principal consumer of corundum ore; imports for the period 1934 through 1940 averaging 3000 short tons per year. The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the United States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918. Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912,

Jan 1, 1945

By C. E. Arnold

IN attacking the problems of mining and treating large disseminated copper orebodies such as those occurring in the Miami or the Ray district of Arizona, one of the vital questions to be decided is, "What is the value of the orebody per ton in place?", The importance of this question lies in the fact that its answer helps to reach a decision concerning the method of mining to be employed. Let it be assumed for the moment that milling and smelting practice, especially the latter, is more or less standardized; and has a cost incapable of much variation, while the cost of mining has a considerable range owing to the large number of mining methods by which a mine may be exploited. For instance, a method may be adopted whereby all the available ore can be extracted perfectly clean (i.e., unmixed with barren material) at a relatively high cost; or a method may be used involving the necessary dilution of a portion of the ore with waste, in order to recover that portion, thus giving a relatively poorer extraction but nevertheless a lower working cost than the former method. Naturally, between these two extremes there lie intermediate methods. In order to arrive at a solution of a mining method problem that is of any value, it is necessary that accurate and complete estimates of mining, milling, and smelting performances and costs shall be established. By way of illustration is given a, case of mining, by the system of undercutting and caving, a large orebody with an average content of 1.50 per cent. copper supposedly all in sulphide form, to which case has been applied those results in mining operations which one may fairly assume are to be expected when viewed in the light of G. R. Lehman&apos;s ore-drawing experiments, which form the subject of a paper to be presented at this meeting. It is assumed that the total. costs will be as shown in the following table:

Jan 9, 1916

By C. E. Arnold

THE CHAIRMAN (PERCY G. BECKETT, Globe, Ariz.).-When you are at Miami tomorrow, you will see a very interesting comparison on the surface of the two mining methods that are being employed there largely. In the case of the surface over the Inspiration mining method, you won&apos;t see very much left of the surface. Everything has gone down. In the case right at the line of the Inspiration ground and the Miami, you will see that the surface over the top slicing which the Miami company has been doing in that country has been riding down evenly and uniformly; and it gives a very marked comparison of the two types of mining, and, to a certain extent, of the different degrees of waste dilution. I would ilke to hear from Mr. Maclennan on this subject. F. W. MACLENNAN, Miami, Ariz.-A paper based on percentage extraction by shrinkage stoping is a difficult one to discuss for the reason that it is hard to arrive at extraction figures until a section has been completely mined out. In the Miami mine we are using a method of shrinkage stoping with narrow stopes and pillars. This ore has been completely broken up and we have started in at the far end to draw off the ore mass maintaining the top of the broken ore dipping at an angle of 60° away from the direction in which we are retreating. A very important point I think about drawing a large. mass of ore down at an angle rather than trying to maintain the top of the ore more or less horizontal is that drawing at a steep angle has a tendency to create a horizontal movement in the ore mass as well as the vertical movement of the ore traveling down to the drawing off chutes. We know that this takes place, on account of the horizontal movement of marked

Jan 12, 1916

By Louis A. Riley

I DESIRE to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomer¬ates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideration in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

Jan 1, 1877

By William Grady

FACTORS entering into the market value of coal are its grade, and the cost of labor, material, and capital. Reduction in these costs cannot be expected in the future, and it therefore follows that greater economy in their use must be accomplished if it is desired to hold the present markets; more tons of product per unit must be obtained in a given time from both men and material, and means devised for increasing the percentage of lump and domestic sizes. This paper is presented for the purpose of inviting discussion and stimulating thought in regard to the influence of methods of procedure and plans of mining, upon the quality of coal, the economical use of labor, material, and capital, and the cost of production. Even the better methods of the. present day leave much to be desired, and a review of the reasons and necessities for their use may be of value in pointing the way to more economical mining. The writer does not attempt to discuss untried methods of mining, but rather to state clearly and concisely a summary of the results obtained under the several methods of procedure that have been adopted. In some instances a high degree of concentration has been effected, and comparisons of the results obtained with the results of lesser degrees of concentration form an interesting study. It is believed that much may be accomplished in improving the quality, and in the more economical use of labor, material, and capital, by concentration, and it is to concentration in particular that your study is invited. The writer, who .has occasion to visit many mines, most of which ire under different management, has been inclined to the opinion that improvement has been retarded in many ways and that mining has not as yet been entirely freed from the early-day practices which were forced upon it.

Jan 5, 1915

By Arthur F. Johnson

THE principal costs of making a pound of aluminum are for 9 kw-hr of electricity and for 1.9 Ib of the oxide (A1203) called alumina. A pound of alumina is made by digesting 2 or 3 lb of bauxite in hot caustic solutions, settling and filtering out the oxides of silicon, iron, and titanium and precipitating and calcining the A1203 as a pure, white powder. The cost of foreign bauxite delivered at an alumina plant in the U.S. may equal or exceed the cost of its chemical treatment to make alumina. Some of the principal factors affecting costs in the utilization of foreign bauxites are: transportation from mine to market, mineralogical and physical composition of the bauxite, thickness of the bauxite beds and their clay and forest overburden, amen- ability of the bauxite to beneficiation and to caustic extraction of the alumina, and lastly size of bauxite deposits and rate of mining employed.

Jan 6, 1954