Search Documents

By Harry R. Cedergren

Properly designed drainage systems can be of great benefit to many kinds of Civil Engineering works, including embankments, and often are the most economical way to protect such works from the damaging effects of water. To function properly, drains must be able to remove water without also removing soil or becoming clogged with soil or erodible rocks. The first criterion to be used in designing drainage systems, called the filter criterion, can prevent all such problems (erosion and clogging) when properly fulfilled in design and construction. The second requirement of drains is that they must be capable of removing all of the incoming water without the build-up of large amounts of head that can damage the protected works. To insure this kind of perfomance, the discharge capabilities of drains should always be verified by appropriate hydraulic and seepage calculations. This paper describes these two basic drain design criteria and also gives examples of application of seepage principles to the evaluation of the potential benefits of drains and to the design of drains for mine waste embankments.

Jan 1, 1985

INTRODUCTION Much discussion has been generated over the years among geologists and engineers as to the ideal drill-hole configuration and spacing for evaluating various types of mineral deposits. Little can be found in the literature about the outcome of the programs, probably because of their subjective nature and the then lack of suitable means of scientific testing. In years past the drilling patterns and sequence were almost entirely determined by the experience and personal bias of the senior engineer, geologist, or project manager on the job. However, planning a drilling program- spacing, pattern, sequencing, etc.-is simply a specific case of sample design, or the design of a sampling program. Having been exposed in the preceding chapter to the theory of regionalized variables, and having learned something about the tools for measuring correlation, or lack of correlation, among samples within a given mineralogical population, we are now prepared to apply these concepts and new-found parameters to a scientifically designed mineral sampling program, be it by drilling or other means. FACTORS IN SAMPLING DESIGN It was shown in Chapter 8 that three major factors should be considered in any mineral

Jan 1, 1980

By George C. Toland, Ronald E. Versaw

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control of the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. The types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent are discussed, together with the technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1977

By J. B. Scuffham, G. I. Warwick, J. B. Lott

The development of solvent extraction processes over recent years has led to their application on an increasing scale in metal extraction plants. The author's company has recently been awarded a contract for the design of the world's largest solvent extraction plant based on pump-mix mixer-settlers. The plant is designed to extract copper from a leach liquor and has an aqueous throughput of 12,000 imperial gpm. The design is based largely upon data obtained from the company's own research laboratories, where work has been undertaken on mixer impeller design, baffle design. settler area, organic entrainment recovery, etc. Investigations have been conducted into the effects of mixer impeller speed, recirculation rates, phase continuity, phase ratio, etc., on extraction efficiency, settler area, and organic entrainment losses. The implications of the results of this work on the design of a large plant using pump-mix mixer-settlers are discussed and the techniques used in overcoming certain scaling problem are outlined.

Jan 1, 1973

By D. S. Choi, H. von Schonfeldt, H. D. Dahl

The design of pillars around a longwall panel in which the effect of the adjacent and worked-out panel is taken into consideration is discussed. A mathematical model is used to duplicate field observations such as opening closure and pillar rib movement. The model is then used to predict the effect of changes in mining geometry on the opening stability.

Jan 1, 1976

By D. S. Choi, D. L. McCain

A method of estimating the chain pillar size required to support the wide working faces of longwall or shortwall coal mining is presented. The pillar size is determined through the use of coal strength, entry geometry, panel width, and overburden pressure. Design analysis is focused on a three-entry development system in the Pittsburgh Seam but can be used for other development plans and other seams by substitution of the proper geometric and strength data.

Jan 1, 1981

By J. C. Bowling

Factors governing the choice of building types, materials, and the details of construction for mineral processing plants in remote locations with cold climates are discussed. Alternative types of building insulation in common use are described and a comparison is made of their suitability under various conditions.

Jan 1, 1973

By Gary E. Butts, Paul R. Smith

Introduction The design of a mineral processing flowsheet involves many factors. The importance of the sample can not be overemphasized. Competent and thorough mineralogical examinations are important as an aid in designing the test program. Designing and conducting the laboratory test program is basic to the design of the flowsheets. In the project under consideration a flotation pilot plant was conducted to prove the process and to provide a realistic prediction of metallurgical results. Moreover, the pilot plant operation provides important pilot plant design data. Finally, accurate and clear reporting is essential so that the information developed can be utilized advantageously by the client and the engineering firm. The design of a minerals processing flowsheet is a team effort. Engineers from the mining company, the research organization, and the engineering firm all contribute to the effort.

Jan 1, 1978

By B. Mueller

Altered concepts regarding the raw material used in conventional blast furnace plants as well as new technologies for the reduction of iron ores make it necessary to reconsider the design of pelletizing plants. The incorporation of a pelletizing plant within a conventional integrated steel mill involves considerations of the problems of using in-plant fines. A modern pelletizing plant in Mexico serves as an example of the technical solution. In recent times, pelletizing plants are also being integrated within steel mills based upon direct reduction processes. The design of such pelletizing plants must take into account special product quality requirements.

Jan 1, 1977

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947

By Howard I. Epstein, John R. Buzek

Thickeners are simply large tanks, usually circular in shape, which are designed to allow settling of solids and to operate with continuous overflow of clear water and underflow of thick pulp. The dimensions of the thickener are usually such that dewatering of very fine pulps may be accomplished while still overflowing clear water. Some thickeners such as the Center, Hardinge and Hydrotator types combine thickening with filtering2 while others such as the Dorr type are pure thickeners. l .2 , 3 A schematic diagram of the traction type Dorr thickener is shown in [Fig 1]. This type is appropriate for tanks over 15 m (50 ft) in diameter. This tank employs a rotating raking mechanism which moves the settled material toward the central discharge. For this and other thickeners, it is common to have a shallow conical tank bottom in order to conform to the geometry of the raking mechanism, and it is often desirable to elevate the tank for ease of access to the product. When the tank does not rest on the ground, the forces resisted by the cone are large, and thick plates must be employed. The fabrication of these tanks requires temporary supports in order to erect the cone. A flat-bottomed tank could also be used because the settled material would soon form a hardened conical surface. However, because of the presence of large bending forces, even larger plate thicknesses are required than for the conical bottom. Significant cost savings often can be realized by the use of a scalloped-bottomed tank such as the one partially shown in [Fig. 2]. The particular scalloped bottom discussed in this paper employs radial beams forming the outline of the cone-shaped bottom. These beams are supported directly by columns. Cone segments are hung between adjacent beams. The exact geometry of these segments depends upon the cone angle and radius, the number of radial beams, and their inclination. The geometry is chosen to satisfy certain clearance restraints and to utilize the material as efficiently as possible. The resulting thickness of these segments is significantly less than that of the equivalent plate for the tank with a conical bottom. This result, along with the simpler fabrication procedures required, accounts for the cost savings associated with this design. The raking mechanism employed may be the same as for the conventional conical bottom since the settled material soon forms a conical surface. Determination of the internal force mechanism for the scalloped bottom leads to designs that utilized material efficiently and thus maximize the cost savings. The complicated geometry of these bottoms along with the difficulty in analyzing the structure are factors which may have limited the use of scalloped-bottomed tanks to date. When such tanks have been built, the uncertainties associated with the internal forces have led to designs that are somewhat inefficient. In this paper, equations relating the geometric parameters are presented along with simplified closed-form solutions for the internal forces in the cone segments, from which the loads applied to the beams and the loads carried to the cylindrical tank shell can be deduced. An example is presented to show the magnitude of the savings which may be realized with this configuration.

Jan 1, 1979

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By M. S. Enders, L. M. Rogers

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining these oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1) mineralization; 2) oxidation; 3) structural setting; 4) lithology; 5) alteration; and ultimately, 6) the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1984

By Donald E. Crowell

Due to falling metal prices and depletion of ore reserves, lead- zinc mining in the Leadville, Colo., area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Co. and Asarco, with Asarco being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Co. of Salt Lake City in conjunction with the central engineering department of Asarco. The plant was constructed by Stearns-Roger Corp. Construction began in the spring of 1970 and the plant went onstream in April 1971.

Jan 11, 1972

By Donald E. Crowell

In the fall of 1969, ASARCO and Newmont Mining Co. began the design of the 700tpd concentrator at their Black Cloud shaft located near Leadville, Colo. The concentractor would treat by flotation a Pb-Zn-Ag ore containing minor gold values. Flowsheet design was based on laboratory test work performed at the Minerals Research Testing Laboratory of ASARCO. Since the concentrator is located at an elevation of 11,000 ft, cold weather was a major factor in design considerations. The original capacity was designed as 700 tpd but for various reasons an ultimate capacity of 1,000 tpd was desired. This necessitated special consideration in the design of several areas, particularly the grinding circuit. The grinding circuit chosen was a single 9 X 12 ball mill operating in closed circuit with one 20-in. cyclone. The ball mill will operate at low speed and as an overflow type originally. The mill can be speeded up and converted to grate type for handling the larger tonnage when required. Thickeners and filters were oversized and space was left for additional flotation cells in order to handle the increased tonnage in these areas. Pumps were sized so that they could handle the increased tonnage by increasing their speed. Construction began in May 1970; the Black Cloud concentrator went on-stream in April 1791.

Jan 1, 1974

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

By E. V. Given

Designing a tailing dam is a major step toward fully integrated mill operation. In the case of large concentrators considerable planning is necessary, and the site of the tailing disposal area may very well dictate the location of the concentrator itself. Before a suitable location can be selected several pertinent factors should be investigated: estimated life expectancy of the mine and, if possible, approximate total tonnage; knowledge of daily mill capacity; and the possibility of future mill expansion. In addition, the area should be able to store tailing for many years and, from a cost and maintenance stand- point, gravity flow will probably be desired.

Jan 7, 1959

By Frank M. Stephens, Robert D. Macdonald

As processes for handling low-grade or complex ores become more complicated and as new methods are found, the need arises for more complete and detailed pilot-plant studies to protect the capital investment required for a full-scale plant. Occasionally a process is firm technically, but there is a need for a demonstration plant that will convince nontechnical men of the wisdom of investing in a full-scale operation.

Jan 5, 1959