Search Documents

LINN BRADLEY, H.' D. EGBERT and W. W. STRONG (communication to the Secretary*).--In the discussion of the paper, a request was made for a further explanation of the curves given on Chart I. In preparing the curves given on this chart, a typical blast-furnace top gas having the following composition by weight was assumed: Per Cent. C02 21.00 CO 24.00 Hz 0.25 CH4 0:25 N2 54.50 For any given top-gas temperature, Curves A, B, C, D, and E indicate in British thermal units the sensible heat lost in cooling the top gas to 60° F. by wet-cleaning methods. Top-gas temperatures are plotted as abscissae, sensible heats above 60° F. in British thermal units are plotted as ordinates, and separate curves are drawn for top gases carrying various amounts of moisture. For any given stove exit-gas temperature, curves A1,-B1, C1, D1, and E1, indicate in British thermal units the sensible heat carried out of the stoves by the moisture which is left in the top gas when it is dry-cleaned and enters the stoves hot. This moisture is removed when the gases are wet-cleaned and the sensible heat which it carries out of the stoves is therefore saved. As before, separate curves are drawn for top gases carrying various amounts of moisture. The curves in Fig. 1, therefore, indicate graphically how much more sensible heat is conserved by cleaning the top gases by the dry-hot method than is conserved by cleaning the top. gases by a cold-wet method and thus removing the greater part of the moisture carried by them. They also show of how little moment it is from a heat conservation standpoint whether or not the moisture carried by the top gases is removed before they enter the stoves. That wet cleaning secures the removal of this moisture and is thus to be recommended from a heat conservation standpoint is an argument often advanced by advocates of wet cleaning. The curves of Fig. 1 show how fallacious such an argument is.

Jan 6, 1917

By J. V. Richards

(Canal Zone Meeting, November, 1910,) THE Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present paper is to describe some of the more common Mexican dry-washing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt." This argo masa occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft.. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted pay-ground was high.

Apr 1, 1911

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrainment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pct, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented.

Jan 9, 1950

By V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pet natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pet of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 11 a in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F.

Jan 1, 1949

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine cool by entrainment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pct, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented.

Jan 1, 1950

By V. F. Parry, E. O. Wagner

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrapment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pet, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented. THIS paper presents a summary of investigations by the Coal Branch of the Bureau of Mines during 1949 on the removal of internal moisture from low-rank coals by processing them in the entrained and fluidized state. A paper on this subject, giving a summary of the early work, was presented at the 1949 AIME annual meeting1 and gave a the- oretical discussion of the time and heat required to dry various sizes of low-rank coal. The investigations on two pilot plants were presented in the foregoing paper. During 1949, three additional pilot plants were built to study phases of the drying problem and to investigate different techniques of handling fine coal in the entrained and fluidized state. The present paper gives operating data on the new units and presents detailed data on the drying of seven coals having bed moisture ranging from 62 to 24 pct. The problem of removing surface moisture from fine coal is principally one of heat exchange and dispersion of the coal particles so that heat can reach the liquid moisture to permit evaporation, and it does not involve the factors of size and time of contact to any great extent. If enough heat can reach the surface of the particles at temperatures higher than 250°F, moisture evaporates almost instantly, and the factors of time and size are of secondary importance compared with the factors of heat balance and dispersion of the coal. Therefore, it does not appear to be necessary to employ a fluidized bed when removing surface moisture, and the most efficient process would be one in which the coal particles are entrained in a hot gas stream of optimum temperature traveling at a velocity that causes the particles to disperse into a low-density phase. When low-rank coals are dried, the fluidized bed is necessary to provide control of time of contact. This is done by adjusting the superficial velocity which controls the density or dispersion of the particles. The density of beds having fluidized properties suitable for drying low-rank coals appears to range from about 5 up to about 15 lb per cu ft. When the density is below 5 lb per cu ft, which represents a low-density phase, optimum conditions for removal of surface moisture should be found, and this requires superficial velocities of about 15 fps. The problem of removing bed moisture from low-rank coals involves consideration of size of coal, temperature, mass flow, heat balance, pressure, time of contact, and method of dispersing the coal in the heating mediums. The experimental work presented here gives data on these factors. Coal sizes up to 1/2 in. x 0 were dried with hot gases having initial temperatures ranging from 1900° to 2400°F. Coal

Jan 1, 1951

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrapment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pet, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented. THIS paper presents a summary of investigations by the Coal Branch of the Bureau of Mines during 1949 on the removal of internal moisture from low-rank coals by processing them in the entrained and fluidized state. A paper on this subject, giving a summary of the early work, was presented at the 1949 AIME annual meeting1 and gave a the- oretical discussion of the time and heat required to dry various sizes of low-rank coal. The investigations on two pilot plants were presented in the foregoing paper. During 1949, three additional pilot plants were built to study phases of the drying problem and to investigate different techniques of handling fine coal in the entrained and fluidized state. The present paper gives operating data on the new units and presents detailed data on the drying of seven coals having bed moisture ranging from 62 to 24 pct. The problem of removing surface moisture from fine coal is principally one of heat exchange and dispersion of the coal particles so that heat can reach the liquid moisture to permit evaporation, and it does not involve the factors of size and time of contact to any great extent. If enough heat can reach the surface of the particles at temperatures higher than 250°F, moisture evaporates almost instantly, and the factors of time and size are of secondary importance compared with the factors of heat balance and dispersion of the coal. Therefore, it does not appear to be necessary to employ a fluidized bed when removing surface moisture, and the most efficient process would be one in which the coal particles are entrained in a hot gas stream of optimum temperature traveling at a velocity that causes the particles to disperse into a low-density phase. When low-rank coals are dried, the fluidized bed is necessary to provide control of time of contact. This is done by adjusting the superficial velocity which controls the density or dispersion of the particles. The density of beds having fluidized properties suitable for drying low-rank coals appears to range from about 5 up to about 15 lb per cu ft. When the density is below 5 lb per cu ft, which represents a low-density phase, optimum conditions for removal of surface moisture should be found, and this requires superficial velocities of about 15 fps. The problem of removing bed moisture from low-rank coals involves consideration of size of coal, temperature, mass flow, heat balance, pressure, time of contact, and method of dispersing the coal in the heating mediums. The experimental work presented here gives data on these factors. Coal sizes up to 1/2 in. x 0 were dried with hot gases having initial temperatures ranging from 1900° to 2400°F. Coal

Jan 1, 1951

By Leon Keller, William R. Van Slyke, James Stukel

Two 4-ft wide DSM screens were installed during 1957 in one unit of the two-unit heavy media cy- clone section of the Holman-Cliffs concentrator at Taconite, Minn., following successful laboratory test work on a 1-ft screen. The two screens materially reduced the amount of media sent to the magnetic separator cleaning circuit. Wear life was good and fine size capacity was high. Briefly, the Holman-Cliffs heavy media cyclone plant uses -65 mesh magnetite as media and 10-in. diam., 30º Ni-Hard cyclones as separatory vessels. Feed to the plant averages 130 long tons per hr of -1/8 in. +65 mesh material. The conventional heavy media circuit uses drum or spiral type separatory units and treats +l/8 or 3/16-in. material. The medium is generally -65 mesh ferrosilicon. Ore and media are readily separated by screening at about 6 mesh. At this size, capacity is high and wear and maintenance are not excessive. The heavy media cyclone plant requires an efficient separation between +65 mesh ore and -65 mesh media. To reduce costs, however, the separation was made at a coarser size with the result that the media was un- duly contaminated and it was necessary to clean large tonnages of media and ore in magnetic separators. Due to the high capital cost of these units, their number was kept to a minimum and, consequently, they were overloaded. As a result, the separation between magnetic media and nonmagnetics was not sharp and the magnetite losses were high.

Jan 10, 1958

By Thomas E. Bruner

With drilling costs playing a pivotal role in the economics of most mineral exploration programs, there has been a significant effort over the past decade to trim expenditures in this area. One result of these cost-cutting measures has been the substantial shift to use of rotary drills. By the mid-1970's, rotary drilling accounted for six times as much footage as core drilling in exploration work. Among the various rotary drilling techniques, the use of dual-tube drilling for continuous sampling is attracting growing interest. Factors such as drilling speed and cost advantages, coupled with favorable comparisons between chip samples and solid core samples, have helped to spark this interest.

Jan 4, 1979

By Wilbur Nelson

ALL of our accounts of the discovery of copper ore at Ducktown, Tenn., state that the discovery was made in August, 1843, yet it would appear that samples of copper from this district were found by the Spanish explorer, DeSoto, when he wandered into Southern Tennessee, in 1539, in his four years of exploration through the Southern States. The following quotation is taken from his diary: "Towards the north there was a province named Chisca; and that there was a melting of copper, and of another metall of the same colour, save that it was finer, and of a farre more perfect colour, and farre better to the sight, and that they used it not so much, because it was softer. And the selfe same thing was told the governor in Cutifa-Chiqui, where we saw some little hatchets of copper, which were said to have a mixture of gold. But in that part of the country it was not well peopled; and they said there were mountains, which the horses could not passe; and for that cause, the governor would not goe from Cutifa-Chiqui directly quicker." DeSoto sent two of his company to try to find these mines, but after five days' wandering through the mountains they returned, stating that their guides had become lost. Although the Ducktown area may have been known to the ancient Indians, it was not until August, 1843, when a Mr. Lemmons, who was panning for gold on Potato Creek, in the Ducktown basin, found some reddish-brown decomposed rock, which he supposed to be gold, that the copper deposits were actually discovered. His disgust on finding that this yellow metal. was not gold was so great that he did not. try to develop his find. In March, 1847, B. C. Dugger erected an iron forge at this same place, but was unable to work the iron as it contained so much copper that on cooling it would break to pieces. The finding of copper in the iron ore by Mr. Dugger led to further explorations; and in April, of the same year, A. J. Weaver, who was passing through that country, told the people that the black rocks they had dug out were rich copper ore. Mr. Weaver began the first mining in this district.

Jan 10, 1924

By Clarence W. Balke

SMALL buttons of fused tantalum have been produced by arc fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By Clarence Balke

SMALL buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreci-able size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numer-ous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the- entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects clue to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

THE production of titanium in 15-1b. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,1 has provided adequate material for a study of the : physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the properties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. [ ] CONSOLIDATION OF THE POWDER The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at so tons per

Jan 1, 1946

By Frank Rieber

EVERYONE is familiar with the story of the poor Indian and his leaking tepee. He couldn't repair the leak while it was raining, naturally. And when it wasn't raining, where was the incentive? Even if this traditional Indian was apochryphal, his counterparts are certainly alive today, and operating on a world-wide scale. - A recent issue of the Wall Street Journal, for example, carried an impassioned letter from an old cocoa planter, who wants the world to know why the price of cocoa has gone skyrocketing. For years, he says, British and American interests have bought cocoa at the cheapest possible price and, incidentally, from growers willing to sell at that price. Between them, they didn't put enough money back into the business, either to fight disease in the cocoa groves or to plant new cocoa trees. Until new trees are planted and come into bearing, we will be paying exorbitant prices for our cocoa, and getting less of it.

Jan 1, 1948

The Duluth Engineers' Club was formally organized on the evening of Aug. 5, 1918, at a meeting .attended by over l00 members of the several engineering professions. W. G. Swart, a member of our Institute, was elected the first President of the Club. At the organization meeting, an opportunity was given, to Alfred D. Flinn, Secretary of the United Engineering Society, to outline the assistance that is being rendered to the Federal Government in the present contingency by members of the engineering profession. Membership in the Duluth Club is to be open to mining engineers on the iron ranges as well as to the residents of the city of Duluth.

Jan 10, 1918

By J. B. Mackintosh

Some months ago I received a sample of a highly crystalline product occurring in the hearth of the shaft-furnace used in smelting the roasted niccoliferous pyrrhotite at Mr. Joseph Wharton's works near the Gap Mine, Lancaster County, Pa. Mr. Wharton first observed this product in cavities in the concretions in these furnaces about the year 1870, and published a description of it in that year.* Thinking that it might show some analogy to meteoric iron, he sent the present sample to Mr. George a F. Kunz, who turned it over to me, with the request that I should analyze it at my convenience. The results do not show the expected analogy, because the sulphur in meteoric iron is combined as FeS., while in this product there is only one-sixth the necessary amount of sulphur, which, however, seems to be combined with all the metallic elements present, forming a sub-sulphide of definite composition. I am informed by Mr. Wharton that he has had for a long time the sample which I have analyzed, and that it probably is about the same age as that which he first described. It is worthy of note that the material does not show any signs of oxidation, but that the crystals preserve a brilliant metallic lustre. The first two analyses, made by Mr. J. Voigt, are those given by

Jan 1, 1888

By Alfred F. Brainerd

A few months since, Prof. Lawrence C. Johnson, of the U. 8. Survey, discovered in Mississippi large deposits of carbonate iron-ore, geologically located in the Claiborne formation of the Tertiary Epoch. These deposits are not pockets, but continuous layers or beds extending for miles, and can be located with certainty where they have not been removed by erosion. Upon examination, recently made by G. W. West, Birmingham, Ala., the largest deposits and highest grades of ore were found near Enterprise, Lauderdale county, and in Clark county, Miss. These beds measure from 10 to 18 feet in thickness, are superimposed upon a " burr rock," associated with green sand, and dip 30 feet to the mile southeast, at an altitude of 350 feet above sea-level, can be

Jan 1, 1888

By Edward Nichols

As far as known to the writer, no discovery has heretofore been made in the United States of deposits of beauxite, or the hydrated oxide of alumina. The deposit which forms the subject of this note was discovered in Floyd County, Georgia. Numerous "float" specimens, covering an area of about half an acre, indicate the location of the main deposit, which has thus far been opened to an inconsiderable extent only. The excavations show the beauxite to exist apparently as large masses in clay. The formation is Lower Silurian, as determined by the Geological Survey of Georgia. The surface in the immediate vicinity is covered with numerous angular fragments of chert, which is a characteristic rock throughout this formation in Georgia. An examination of the mineral shows it to have the oolitic structure common to several beauxites. It. varies in color from a light salmon to dark red, depending upon its contents of iron oxide. The light-colored specimens are comparatively soft, while the dark mineral is much harder, spots in the latter being

Jan 1, 1888