Search Documents

By Leland L. Mink, Roy E. Williams, C. Daniel Kealy

The passage by Congress of Public Law 92-500 (the 1972 Water Pollution Control Act amendment) has placed a new emphasis on the need for methods to minimize the escape of water from tailings ponds. Presumably tailings pond seepage will fall under the jurisdiction of the act. This paper is designed to explain some of the problems caused by leakage from tailings ponds and to present a method by which leakage can be minimized if not eliminated. Ground-water pollution in one case studied by the authors results from leaching of old jig tailings that are intermixed with the upper part of a sand and gravel aquifer. Anomalous concentrations of zinc, lead, and cadmium occur in ground water and soil samples taken from the portion of the sand and gravel aquifer containing the old jig tailings. Analysis of water samples from a tailings pond located in the area indicates that the pond water is not the source of the heavy metal concentrations found in the down-gradient ground water. However, leakage from the pond and water from the pond's decant system combine with natural ground water to compound the problem by raising the water table into old jig tailings which cover the upper portion of the aquifer. The ground water which discharges from this aquifer causes a statistically significant decrease in the quality of the receiving stream water. The shallow ground water contains oxygen; therefore, corrective measures include lowering the water table to depths below the old jig tailings which cover the aquifer at ground level. This, in turn, implies elimination of ground-water recharge by subsurface leakage from the pond. A laboratory study and a mathematical model study have revealed that seepage from such ponds can be minimized by a carefully designed and managed peripheral tailings discharge system. The process involves maintaining the slime zone and the free-water surface near the center of the pond so that the slimes retard downward and semilateral movement of pond water. The free-water surface must not be allowed to extend out over the nonslime portion of the tailings during or after pond operation. Mathematical model output reveals that this method can hold the subsurface discharge rate to as little as 110 gpd per acre of pond water area. The technique should be applicable to any tailings pond system in which the loss via seepage of poor quality water must be minimized or where recharge of ground water by losses from a tailings pond must be minimized, regardless of the reason.

Jan 1, 1974

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 5, 1950

By Marston G. Fleming

CRITICAL pH has been defined by Wark1 as that pH value below which a mineral will float and above which it will not float in solutions containing a given concentration of collector but free from other depressants or activators. - The relationship between mineral, collector concentration, and pH is expressed in the form of a critical pH curve determined by the captive bubble method and is generally regarded as being fundamental to the system involved. The mechanism of alkali depression is currently in dispute, two general theories having received authoritative support. The view expressed in Taggart's chemical theory of flotation2 is that in the presence of a critical concentration of hydroxyl ions, all the metal ions available at the surface of the mineral are present as anions of the form [M (OH)x]-y. The formation of the necessary metal xanthate is thus precluded and, furthermore, any metal xanthate coating previously formed, at a lower pH, will be dissolved. Gaudin3,4 and the Melbourne school under Ware hold that alkali depression is caused by the preferential adsorption of hydroxyl ions by the mineral surfaces. This paper describes an investigation of the mechanism of alkali depression in each of the three systems: cerussite-aqueous carbonate-xanthate, cerussite-xanthate, and galena-xanthate. Alkali Depression of Cerussite by Control of Carbonate Ion Concentration Wark and Cox6 have shown that in the presence of Na2CO3 a higher concentration of xanthate is required to effect bubble contact with a cerussite surface than in carbonate-free solutions. To examine this depression of cerussite by sodium carbonate, a series of captive bubble tests was carried out on cerussite specimens in solutions containing 100 mg per liter of potassium ethyl xanthate and varying concentrations of sodium carbonate. The pH was adjusted by the addition of dilute hydrochloric acid. For purposes of comparison a standard critical pH curve was determined for cerussite with potassium ethyl xanthate in solutions containing no added carbonate. In the latter case pH adjustment was made with sodium hydroxide. The experimental method employed in both series was broadly similar to that described by Wark and Cox;7-9 a number of refinements suggested by Sutherland10 were adopted, and the procedure was further developed and modified to suit the particular requirements of the investigation. The relationship between pH and the concentration of potassium ethyl xanthate necessary to induce bubble contact at cerussite surfaces is shown in Fig. 1. The relationship between pH and the concentra- [ ] tion of sodium carbonate necessary to prevent bubble contact at cerussite surfaces in the presence of 100 mg per liter of potassium ethyl xanthate is shown in Fig. 2. Comparison of the. two curves shows that at a collector concentration of 100 mg

Jan 1, 1952

By B. B. Bucky

THIS investigation was carried on by means of models and the applica-tion of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimensions. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in- bed B, a 3/8-in, bed C and two 1/8 -in. beds D and E. The model was rotated at ±2350 r.p.m. equivalent to a model ratio of 1268. It was worked back 1/4 in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious ,reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft, and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel 1/8 in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1939

By John W. Stevenson

In gassy coal mines, abandoned worked-out areas are natural reservoirs that may contain air- methane mixtures. The quantity of such mixtures is continuously increasing or decreasing as atmospheric pressure falls or rises. This is in accordance with Boyle's Gas Law, which states that the volume of a perfect gas varies inversely with the absolute pressure. In large, open gob areas without a bleeder ventilation system, atmospheric pressure is a static force acting in all directions. Changes in atmospheric pressure may occur rapidly or slowly, but any change will result in a change in the quantity of gob air-methane mixtures.

Jan 6, 1968

By Nick Barton, Stavros Bandis

The descriptive term "rock mass" encompasses individual block dimensions ranging from centimeters to many tens of meters. Strength and deformability vary both qualitatively and quantitatively as a result of this size range. A key issue is therefore the appropriate size of the test sample. A large body of test data was reviewed to determine the influence of block size on the displacement required to mobilize peak strength. It is shown that the shear strength and shear stiffness reduce with increased block size due to reduced effective joint roughness, and due to reduced asperity strength. Both are a function of the delayed mobilization of roughness with increasing block size. A method of scaling shear strength and shear displacement from laboratory to in situ block sizes is suggested. It is based on the assumption that size effects disappear when the natural block size is exceeded. This simplification appears to be justified over a significant range of block sizes, but is invalidated when shearing along individual joints is replaced by rotational or kink-band deformation, as seen in more heavily jointed rock masses. Recent laboratory tests on model block assemblies illustrate some important effects of block size on deformability and Poisson's ratio.

Jan 1, 1982

By D. A. Sangrey, D. Marcus, S. A. Miller

A methodology was developed wherein the increase in compressive strength, mineralogical changes, and pore water composition were studied simultaneously as a function of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. The specific data are applicable only to the material studied. But the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1986

By K. N. Clark, N. B. Carter, C. G. Thomas, V 7. 0 / 300 dpi

A statistically designed, experimental study showed how gangue minerals, flux additions, fineness of grind, firing temperature, and time affect the properties of acid pellets made from a Western Australian hematite ore. Alumina has less effect than silica and lime, but interactions between the six variables occur, which influence abrasion index, reducibility, and cold compression strength. Finer grinding has little influence on reducibility but improves the other two properties. The major variable is firing temperature, which interacts with all other variables to affect pellet properties. Calculations based on the data show the implications for straight-grate pellet plants and optimum hood temperature ranges.

Jan 1, 1982

By William E. Galloway, Gary E. Smith, Christopher D. Henry

INTRODUCTION Studies relating to the Oakville aquifer as presented in this report and by Henry et al. (this volume), are part of a larger , comprehensive examination of regional and local stratigraphic, hydro- geologic, and geochemical parameters within the Oakville Formation recently completed by the Bureau of Economic Geology. The Oakville serves both as a major Gulf Coast aquifer and an important uranium host (Fig. 1). Regional and local controls on hydrodynamics and hydrochemistry have important implications for hydrochemical exploration, the establishment of premining baseline parameters, and the design of post mining restoration procedures. Investigations of the Oakville Formation were de- signed for the purpose of determining the response of the aquifer to uranium extraction and were funded by the U.S. Environmental Protection Agency under grant numbers R-805357-01 and R-805357-02. Physical Stratigraphy Physical stratigraphic analysis shows that the Oakville Sandstone, a lithostratigraphic unit deposited by a major coastal-plain f luvial system, consists of five mappable, component depositional elements (Figs. 2 and 3). Each major component element is the product of one or more rivers traversing the Miocene coastal plain. In turn, each river possessed a unique sediment load, discharge characteristics, and source terrane. Consequently, each element exhibits distinguishing geometric and compositional parameters that potentially influence the flux and hydrochemical evolution of contained ground waters (Galloway, Henry, and Smith, in preparation). The Oakvil le Sandstone, as mapped and interpreted as a lithostratigraphic unit in the study area, corresponds closely to the Jasper aquifer system, an equally well-defined Gulf Coastal Plain hydrogeologic unit (Baker, 1978). Principal surrounding hydrogeologic units include the underlying Catahoula confining system, the Jasper aquifer system itself, and the overlying Burkeville confining system (lower Fleming mudstones). The Evangeline aquifer system includes much of the Fleming Formation. The Jasper aquifer system is bounded above and below by relatively less transmissive, finer grained confining systems, although absolute transmissivity varies greatly within both the Jasper and confining units. Lithostratigraphic and hydrogeologic boundaries coincide almost exactly within the Hebbronville flu- vial axis (Fig. 3). Correspondence of geologic and hydrostratigraphic boundaries is good within the George West axis; farther to the northeast the correlation of the Jasper aquifer with units mapped as Oakville Formation diverges to varying degrees. A complete analysis of these trends and a study of the depositional facies comprising the Oakvillle are included in Galloway, Henry, and Smith (in preparation). REGIONAL HYDROGEOLOGY The stratigraphic, compositional, and structural framework of the Oakville Formation and the mosaic of interrelated depositional facies that are combined in this framework play a key role in defining the hydrogeology of the Oakville. Furthermore, a combination of climate and hydrogeology, as well as past and present socioeconomic conditions, has determined water and land use patterns within the region of Oakville outcrop. Utilization of Oakville Ground Water Stratigraphic control for determining which wells produce ground water from the Oakville aquifer was established by preparing structural and isopach maps of the Oakville Formation using regional electric log cross sections. Surface elevation and screened interval data (or total well depth, if open-hole completion techniques were used) from each water well, combined with the stratigraphic data, allowed accurate assessment of the producing aquifer for individual wells. Information on well and screen depths, water levels, and usage of water from

Jan 1, 1980

By R. L. Templin

IN TREATING a cast metal by any working process such as rolling, drawing or forging, variations in the conditions present in the remelting, casting, chilling and preheating of the initial ingot will certainly have some effect on the physical properties of the final product. In considering the effects of cold working on the physical properties of metals, however, it will be assumed that these factors, being controlled according to best practice, will remain constant and therefore may be neglected. Starting with such a uniform metal ingot, the next operation in the production of wrought metal involves hot working by rolling, forging or extrusion so as to produce a slab, billet or bloom. This working must be sufficient to produce substantial grain refinement and minimize any defects occurring in the initial ingot. Even such a hot-worked product is not suitable as a starting material for determining the effects of cold working because it contains internal strains analogous to those resulting from cold working. It is necessary, therefore, to supplement the hot working with a considerable amount of cold working, followed by a proper annealing in order to obtain a material suitable for use in defining the effects of cold working on the physical properties of a metal. That is, if the effects of cold working are to be evaluated accurately it is necessary to have other effects at least constant if not absent. Such material, unfortunately, cannot always be obtained in commercial practice but the requirements just indicated certainly represent the desired goal; this goal has been attained in the treatment of some metals, one being aluminum.

Jan 1, 1929

By F. J. Mehringer, C. W. MacGregor

VARIOUS investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-12 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 [ ] where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. PRELIMINARY INVESTIGATIONS The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 019 per cent; S, 0. 118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Elect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By Frederic Becket

IN a recent article,1 which described the softening effect of columbium in plain high-chromium steels, the authors stated that their investi-gations had shown columbium to be also a particularly valuable inhibitor of intergranular corrosion in steels of the 18 per cent chromium, 8 per cent nickel type. It is the purpose of the present paper to record some of the results obtained through the introduction of columbium to the austenitic chromium-nickel steels. The damaging effects of this type of corrosion have become so widely known as to restrict considerably the applications of the steels under consideration, and therefore there is little question of the importance of the goal to be attained. Numerous contributions concerning the susceptibility of the aus-tenitic chromium-nickel steels to intergranular corrosion have appeared during the past few years, and among others who have dealt construc-tively with the subject are such well-known authors as Strauss and Houdremont of Germany, Hatfield of England, and Bain in the United States. Different theories have been propounded as to the cause of intergranular corrosion, and various remedial measures have been proposed, the majority of which involve the use of addition agents. Titanium is the addition agent at present most generally employed, as suggested by Houdremont and modified as described by Bain, Aborn and Rutherford.2 Little has been published on the effects of holding these steels for long periods at the relatively lower temperatures in the presence of

Jan 1, 1934

By Ove Rehnberg

Catalytic purifiers are widely used as exhaust treatment devices on diesel equipment in confined spaces. The paper summarizes some studies carried out at the University of Lulea on diesel exhaust purifiers. The main purpose has been to elucidate important chemical activities of catalysts useful for the improvement of their effect. The effects of platinum catalysts on exhaust constituents such as carbon monoxide, nitrogen oxides, unburned gaseous hydrocarbons, and polynuclear aromatic hydrocarbons are discussed. Also pointed out are the great differences in catalyst activity and advantages/disadvantages associated with the catalysts.

Jan 1, 1982

By George F. Comstock

IT has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- [ ] loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferro-alloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. METHOD OF USING DEOXIDIZERS The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel [ ] shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to ¾ -in. lumps,

Jan 1, 1942

By Philip Bucky

THE term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater mecha-nization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar model built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimensions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein.

Jan 1, 1938

By F. R. Hensel

THE demand for clean steel is increasing daily. New processes of refining steel are being developed in order to remove all nonmetallic inclusions as completely as possible, as it is the general opinion that. inclusions affect the dynamic properties of steel and iron to such an extent as to justify great expense for their removal. It is surprising to note at the same time the commercial development of a new process for making artificial wrought iron. By this process slag and steel are thoroughly mixed, the amount of nonmetallic inclusions usually exceeding 2 per cent in weight. The contradiction in these two efforts is obvious and is responsible for the investigation reported in this paper. H. W. Gillett also has recently emphasized the need for further research on wrought iron.1

Jan 1, 1932

By Russell Franks

IN recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic properties. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 the cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he presented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield? pro-posed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400° to 600°C. to precipitate carbides in order to obtain better mechani-cal properties. Discussions by Sutton,4,5 de Ganahl,6,7 8 Krivobok and Lincoln,9 Knerr,10 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in light-weight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb, per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 x 10[9] cu yd (1.4 X 10[9] m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 X 10[6] cu yd (19 X 10[6] m3) annually.

Jan 11, 1979

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 X 109 cu yd (1.4 x 109 m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 x 106 cu yd (19 x 106 m3) annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators can expect improved rope life by periodic review of their practices and by adopting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by a factor of five among the sites studied, considerable improved average performance is possible. As little as 10% overall improvement would increase national productivity by 2 million cu yd (1.5 X 106 m3) of solid overburden removal. Associated savings in rope costs would be some $2 million annually, plus a large reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. During the field survey, no company was found which had tried cost reductions by using presocketed dump ropes, or dump rope sheaves that opened like a snatch block, so these are suggested as possible improvements requiring modest capital input. Data Acquisition During the field visits, mine operators provided rope life information about their machines. Some of the rope life data consisted of gross averages; other data was in the form of detailed records, including rope construction and manufacturer, cutoff and resocketing periods, end-for-end switching, and downtime for rope change-out. Trends of average hoist rope life and average drag rope life determined from the field study are shown in [Fig. 1] as a function of bucket size. The three lines on the graph have slopes of 1, M, and 1/4. A comparison of the data shows that hoist ropes moved about twice as much material as drag ropes prior to retirement, although more than a two-to-one scatter within each category is evident. As expected, the larger machines with the larger buckets moved more total volume of material. The four pairs of solid symbols represent those data for which detailed rope life histories are presented in subsequent figures.

Jan 1, 1980

By Y. P. Chugh, R. A. Missavage

Moisture has been known to influence strata failures in coal mines for a long the. A concise review of what is known about effects of moisture on strata control with emphasis on the Illinois basin coal mines is presented in this paper. Some approaches to mitigate the effects of moisture-leaving coal in the roof, guniting, shotcreting, application of sealants-are then briefly discussed.

Jan 1, 1982