Search Documents

By D. L. Johnson

Only general treatment of a subject of such scope can be given in a short paper, therefore, except in a few instances, statistics and descriptions of specific installations are omitted. The earlier applications of electricity to the production of petroleum in the Mid-Continent field were widely separated chonologically, each holding a special interest, and each contributing greatly to the present development. Electric Pumping One of the first installations of electric pumping was on a lease near Jenks, Okla., in the Arkansas River bed, where a difficult problem was solved by the use of motors. The Arkansas River had frequent flood periods which interfered seriously with the use of jacks and pull rods. Small piers were built with old casing used as piling, and upon these were set small jacks driven by 3-hp. squirrel-cage motors. The starting switches were located on a bank and the power was furnished by a small generator, which was driven by an oil country gas engine. This installation was made in 1913 and is, I believe, still in satisfactory operation. In 1914, the Cushing field came in and the Hill Oil & Gas Co. electrified its Shamrock property, using eight-pole Star Delta motors, rated at 10 to 30 hp. and belted through countershafts to the band wheel. Power was furnished by a small generating plant consisting of two 135-kw. machines, gas-engine driven. Considerable difficulty was experienced in the early operation of this station because of low voltage. It is characteristic of small alternating-current generators that voltage regulation will be poor with widely fluctuating loads. This field had three producing sands, and a number of wells were redrilled with the motors, and this, together with a great deal of swabbing, was responsible for the bad load conditions. However, when the wells had settled down to steady operation, the electric equipment functioned satisfactorily, and continued in use as installed until a few years ago when the present owners contracted for service from a central-station company and shut

Jan 1, 1928

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 33? per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 Per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. Mine Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three a 13,800/440-volt, single- phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp motor on the No, 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 500-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft, Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. under normal operation the one pumping 1200 gal. per min, is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started1 and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the Pumps restart. On failure of any Of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 37' substation is run to the switching station, in which are four 15-kv., 600-amp. direct-current sole-noid-operated oil circuit breakers. The current for Operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1946

By F. O., Garrabrant

ELECTRIC power requirements for Climax are similar to those of most metal mines, except that large blocks of power are used underground and there are a number of other unusual applications. Power is furnished to the Company by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are designed so that with the addition of forced cooling their capacity may be increased a third at 12,000-ft. altitude. On the secondary side of this bank is a 15-kv., 1200-amp. oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. (A more complete description of the electrical distribution system at Climax, with detailed drawings, is contained in T.P. 1734, A.I.M.E., Mining Technology, July, 1944.)

Jan 1, 1946

By Graham Bright

T HE chairman of the Mines Committee of the A. 1: E. E. for 1920-21 has had the honor of being also the chairman of a similar committee, the Mine Equipment Committee, of the A. I. M. E. It has been the endeavor during the past year to have the two committees work together since the object of these committees is very much the same. A meeting of the committees was held in Chicago in November of 1920, at which time it was decided that one of the best ways to work together would be to foster joint meetings of the local sections of the A. I. E. E. and A. I. M. E. By these meetings, it was hoped that various engineers in the local sections interested in mining subjects could be brought together and not only become better acquainted but be greatly benefited by the interchange of ideas and by the discussion of papers presented on mining subjects.

Jan 1, 1921

By F. O. Garrabrant

POWER is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt line to a bank of three 3333-kva. Transformers 100/13.8 kv. These transformers arc so designed that with the addition of forced cooling their capacity may be increased 33 1/3 per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200- amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. MINE Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three 250-kva, 13,800/440-volt, single-phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp. motor on the No. 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 100-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft. Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. Under normal operation the one pumping 1200 gal. per min. is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started, and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the pumps restart. On failure of any of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 370 substation is run to the switching station, in which are four15-kv., 600-amp. direct-current solenoid-operated oil circuit breakers. The current for operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1944

By RAY J. CORFIELD

IN a previous paper, "Electric Shovel Operation at Utah Copper Mine," which was read before the Western Division of the American Mining Congress, the problem of electrifying a fleet of steam shovels was described. This paper deals with the electrification of the haulage system which, when completed, will make the mining operation completely electric, with the exception of drilling operations which will continue to be performed by air. The general layout of the haulage system involves the use of heavy curves in addition to heavy grades of between 4 and 5 per cent. In a mining operation of this kind no trackage can be called permanent; this complicates the overhead construction somewhat and makes it necessary to design special forms of trolley construction, some of which will be described in detail below.

Jan 1, 1929

By Dorsey Lyon

I. INTRODUCTION THE utilization of hydro-electric power in electro-metallurgical indus¬tries, aside from purely mechanical operations, may he of two kinds. The electric energy may be used to supply the heat necessary for the per¬formance of the chemical reactions of a metallurgical process, or the elec¬trolytic action of a direct current may be employed for extraction of metals, either in a reduction process or a refining process. In discussing this subject, it is well to distinguish between established industries, which are producing metals and alloys at a profit by use of the electric current, and the many processes which are either still in the experimental stage or have not even passed the paper stage of development of a patent. That is, we consider electro-metallurgical industries as commercial operations which are now consuming large blocks of electric energy, while processes which are not in commercial operation are only prospective consumers. Also, owing to the difficulty and risk of any attempt to foresee the effect of the European war upon electro-metallurgical industries, we have felt obliged to disregard the war entirely, and state our opinions regardless of its existence.

Jan 8, 1915

By Orson Shepard

THE term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 19341. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner:. . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1936

By I. Iwasaki, P. L. De Bruyn

Electrical double-layer properties of the silver sulfide-solution interface in different electrolytes and the influence the properties exert on the adsorption of dodecylammonium acetate (DAA) were studied using an electrochemical titration technique. The flotation behavior of silver sulfide was observed using DAA as collector and the results were correlated with adsorption measurements. Silver and sulfide ions were identified as the potential determining ions and their adsorption densities were measured as functions of the pAg and of the ionic strength at two different pH values. The point-of-zero-charge (PZC) was observed to be at pAg 10.2, the value being independent of pH and of the nature and concentration of the electrolyte used. The surface charge of silver sulfide in these electrolytes was positive for pAg values less than 10.2 and was negative for pAg values greater than 10.2. The adsorption of amine on silver sulfide surfaces at pH 4.7 was found to be strongly dependent on the pAg. A shift in the PZC towards a lower pAg due to the adsorption of amine indicated a specific affinity of dodecylammonium ion towards silver sulfide surfaces. At pH 9.2 a strong adsorption of the undissociated amine molecule was indicated. The PZC shift towards a higher pAg and the adsorption of the amine was virtually independent of the interfacial electrical conditions.

Jan 1, 1972

By J. J. Pavlica, I. Iwasaki

Grinding in steel milk adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and galmic current measurements were made on electrode combinations of pyrrhotite-mild steel and pvhotite- stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles cawed slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1983

By K. A. Natarajan, I. Iwasaki

Electrochemical measurements were made wing chalcopyrite and pyrrhotite electrodes in aqueous solution containing a xanthute collector and ground ore mineral particles. The purpose was to investigate the electrochemical reactivity of ozone with respect to dissolved xanthute, surface adsorbed xanthute, and the sulfide mineral itself. Electro-chemical evidence for the removal of xanthate coatings from chulcopyrite, pyrrhotite, and platinum surfaces by ozone is presented. The oxidizing power of ozone is compared with that of oxygen and other common oxidizing agents to portray the superiority of ozone as an oxidant.

Jan 1, 1986

By Harold Markus, Gerhard Derge, Arthur Grobe

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from ½ to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.1°. Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Harold Markus, Arthur H. Grobe, Gerhard Derge

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study. has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from 1/2 to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.? After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been damped. The pH of the electrolyte was controlled? by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.10. Potentials were measured against a saturated calomel electrode connected. to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Y. M. Chang, C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 Rc was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique. Weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure erosion, it was found that there was a synergistic effect between corrosion and erosive wear. Corrosion rate, erosion rate, and total erosion/corrosion rate are given as a function of pH and mineral type.

Jan 1, 1986

By Shun-ichi Satoh

A NEW method of treating steel by ammonia has recently been intro¬duced into the metallurgical industry, by means of which piston cylinders of internal combustion engines, shafts and other similar steel products can be made more resistant to wear than formerly. In 1929 the writer' published the historical notes and some experiments upon nitrification. He believes that the corrosion of nitrified steel is a matter of importance and worth studying; and as there have been few studies thereof, he has conducted experiments in this respect. L. Guillet,2 in 1927, reported corrosion tests made on nitrified and cemented steels with acid and salt solutions. In 1928, 0. Hengstenberg3 reported the high resistance of nitrified steel to water vapor and air. V. 0. Homerberg4 stated that nitrified steel has high resistance to water, air and salt solution; and G. Hagg5 studied nitrified layers of iron by means of the X-ray. Though F. Hanaman6 in 1913, measured the single potential difference of steel treated with ammonia at above 650° C., no one, it seems, has ever measured the single potential difference of the so-called nitrified steels having extraordinary hardness. The writer measured the single potential differences of nitrified special steels in various solutions with the object of studying the corrosion problem and, if possible, of knowing whether any new physical property would be caused by nitrification.

Jan 1, 1932

By Milton E. Wadsworth, J. Brent Hiskey

INTRODUCTION Fifteen years ago a distinguished electrochemist referred to electrochemistry as an "underdeveloped science " In the article in question, Professor Bockris (1) stated that many areas of.natura1 phenomena and applied technology are not perceived as being electrochemically based At that time, this was especially true for much of non-ferrous extractive metallurgy and was a particularly accurate description of hydrometallurgy During the last decade, there has been considerable advancement in applying the theory of electrochemistry to our know1 edge of hydrometallurgical processes and in understanding the mechanisms of underlying electrode reactions. Impressive as these advances are, there is still a growing need for electrochemical research of mineral systems and electrochemical engineering to apply this work in practical situations In a broad sense electrochemistry is defined as the physical chemistry of ions in solution and of phenomena which occur at the electrified interface. Bockris and Reddy (2) refer to electrochemistry as being divided into two fundamental domains, ionics and electrodics ionics is restricted to the behavior of ions in solutions, examples being many familiar redox processes Electrodics represents the main part of electrochemistry, and is the study of charged interfaces and the conditions governing charge transfer reactions across them. Considering hydrometallurgical applications, electrodics suggests the following relationship for a conducting solid (bulk or surface)

Jan 1, 1981

By S. Chander, D. W. Fuerstenau

The inherently sluggish nature of the reactions involving sulfide minerals, particularly molybdenite, in aqueous solutions under ambient flotation conditions make their investigation complicated and difficult. Since the physicochemical nature of sulfides is known to be controlled by electrochemical reactions, a number of attempts have been made in the past to study sulfide mineral-collector interactions through rest potential and electrode polarization measurements. The purpose of the present investigation was to study the interaction of potassium diethyldithiophosphate (KDTP) with molybdenite. In the present investigation of the interaction of KDTP at the molydenite surface, molybdenite electrode rest potential measurements and electrode polarization behavior were experimentally determined under various solution conditions. The standard reduction potential for the equilibrium between dithiophosphate ions (DTP-) and bis(diethoxythiophosphoryl)disulfide (DTP) [(DTP). + 2e :i7-± 2DTP- (1)] can be evaluated from the electrode rest potential measurements on a platinum electrode in deoxygenated KDTP solutions saturated with freshly prepared (DTP)2. Experimental A platinum wire was used as the electrode for potential measurements. Prior to each measurement the elec-

Jan 1, 1975

US 4,183,794 - Electrowinning zinc from a zinc sulfate solution produced by leaching zinc ore with sulfuric acid. The leach liquor is subjected to electrolysis in a first cell having an insoluble anode to deposit primary zinc on the common electrode. The coated electrode is transferred to a second cell having an alkaline electrolyte, and electrolysis is effected in the second cell to transfer zinc from the common electrode to the second cell cathode in a spongelike form which is readily stripped. R.H.C.L. Ross. Jan 15, 1980. 10 pp. (204-119). Filed: 12-22-77 (863,190). Same: Canadian 1,051,820, dated Apr. 3, 1979.

Jan 1, 1982

By P More

US 4,132,621-In the electrowinning of aluminum, the cells are aligned in a lengthwise direction so as to lessen the harmful influence of the induced magnetic fields Each cell is supplied with current from the preceding cell both via the head arid at least one side riser The output of the cathode bars is divided into two separate groups, the upstream group supplying the head of the subsequent cell arid the downstream group supplying the side risers of the subsequent cell This produces a substantial improvement in cell efficiency arid a greater regularity P Morel, J P Dugois, arid B Langon, assigned to Aluminium Pechiney. Jan 2, 1979 12 pp. (204¬243M) Filed 1-12-78 (868,861) Priority: France, 1-19-77 (77/2,213) US 4,134,806-Cells, anodes, arid methods for use in the electrowinning of nickel, cobalt, copper, zinc, or other metals from an acid ore leach solution or the like The cell is provided with vertically immersed stationary cathodes and stationary rod anodes which are noncorrodible by the electrolyte arid are electrocatalytic to the anode reaction. The spaced parallel anode rods are connected to electric current supply bars The anode rods have an electroconductive core made of a metal alloy arid a surface coating of an oxide of platinum or a platinum group metal The ratio of active cathode surface area to active anode surface area is preferably at least 3 0. De Nora arid C Traini, assigned to Diamond Shamrock Tech¬nologies, SA Jan 16, 1979 13 pp. (204-105R) Filed 9-15-77 (833,661) Priority Italy, 1-29-73 (19738 A/73). Same British 1,434,334-5, dated May 5, 1976 US 4,135,994-In the electrowinning of aluminum at a high current efficiency, the electrolytic bath is a mixed molten salt consisting of 2-15% by weight of aluminum trichloride, 15-83% of sodium chloride, 15-70% of combined calcium chloride arid magnesium chloride but riot more than 40% of calcium chloride, arid optionally up to 10% of barium chloride Preferably, plate-shaped graphite electrodes used for both cathodes and anodes are arranged in parallel inclined relation so that the axis in the lengthwise direction makes an angle of from 10° to 45° to the horizontal. T Ishikawa arid H Ichikawa, assigned to Nippon Light Metal Co Ltd Jan 23, 1979 4 pp (204-67) Filed 11-15-77(851,632) Same British 1,550,502, dated Aug 15, 1979

Jan 1, 1980

By J. D. Miller, P. J. McDonough, H. Q. Portillo

Previous investigations have demonstrated the catalytic effect of silver additions in the ferric sulfate leaching of chalcopyrite [ ] The enhanced rate of leaching was found to be due to the formation of an intermediate Ag S film which forms on the Cures2 surface by an exchange reaction Under these conditions, unlike the uncatalysed ferric sulfate leach, the elemental sulfur forms a nonprotective reaction product on the Ag S crystallites As a result, the rate appears to become limited by an intermediate electrochemical reaction in {he Ag2S film rather than by transport through the elemental sulfur reaction product [ ] The reaction rate was found to have a complex dependence on the Ag+, Fe++ and Fe+3 concentrations, but independent of the Cu concentration Electrochemical measurements with a Ag,S-coated chalcopyrite electrode provide further information regarding the nature of the reaction mechanism The kinetics of the rate limiting, intermediate electrochemical reaction are analyzed in terms of the Butler-Volmer equation

Jan 1, 1981