Search Documents

By A. W. Schlechten, Ernest J. Breton Jr.

Experiments on the separation of copper and zinc ions by selective action of ion exchange resins showed the carboxylic type to be more effective than the sulphonic resins. The latter demonstrated a greater capacity over a wider pH range. Data show the effectiveness of resins as a means of concentration. IN recent years the restrictions of stream pollution laws and the high price of metals have created an interest in ion exchange as a means for metal recovery. Some applications have proved successful. In Germany during World War 11, 17 tons of copper per day were recovered from rayon mill wastes by means of ion exchange resins;' and for some time in this country a large ion exchange unit has been in operation for the recovery of copper from rayon waste water. The possibilities of applying ion exchange to the recovery of metals occurring in plating rinse water is particularly promising. In most of these applications only the metal being recovered occurs in the waste. The ion exchange resins act merely as a means of concentrating the metals to a point where they can be recirculated. It would be highly desirable to use ion exchange as a means of not only concentrating but also of separating metals. With the exception of the impressive separations accomplished in connection with the atomic energy program, very little has been done on metal separations.' Therefore, an investigation was undertaken at the Missouri School of Mines and Metallurgy to determine if either of the two main types of ion exchange resins could be used to separate metal ions in solution. The selective removal of copper ions from a mixture of copper and zinc on carboxylic and sulphonic-type resins was investigated as a function of flow rate, pH, copper-zinc ratio, and concentration. It was shown that zinc can be separated from copper and that very large ratios of concentration can be obtained using ion exchange resins. Since ion exchange is relatively new to the field of metallurgy, a brief review of the subject will be included. Theory of Ion Exchange A comprehensive theory for ion exchange has not been developed as yet, but the mechanisms are analogous to metathetical reactions: R Na + Cu++ *=? K(SO3)2 Cu + 2Na+ R is the designation for the ion exchange resin. If a copper solution is passed over a resin bed in the sodium form, two ions of sodium will be released for every ion of copper removed. For the most part this reaction follows the laws of mass action and of electrical neutrality. Consequently, if an excess of sodium ions is passed over a bed containing copper, the reactions will be reversed, and the resin will be regenerated to its original form. A few empirical rules governing the exchange reaction have been set forth: 1—In general ions with a high valence will replace ions with a lower valence. 2—Ions having higher activity coefficients have a higher replacement potential. 3—In a series of mono-valent ions, those with the smallest radii of hydra-tion will tend to replace those having larger radii of hydration. 4—Where ions are similar in most respects, those with the higher atomic weight sometimes will take precedence. This last rule is not as definite as some of the others. These rules apply to rather dilute solutions at moderate temperatures and assume all ions to be present in about equal concentrations. Higher concentrations and temperatures may in some cases reverse the normal exchange reactions. Ion exchange materials are unique in that their efficiency increases as the concentration of the solution decreases. For many exchangers, most efficient operation is obtained at concentrations in the order of one thousandths of a percent. Most applications, though, are made in solutions containing considerably higher concentrations than this. Coste9 as shown that ion exchange resins will remove aluminum and iron effectively' from solutions of up to 10 pct chromic acid. Ion Exchange Resins Ion exchange resins are insoluble, porous, resinous structures to which active groups have been attached. Active groups such as (—SO,,)- and (COO)- pick up cations; hence structures saturated with groups such as these are called cation exchangers. Structures saturated with groups such as (—NH,)' which pick up anions, are referred to as anion exchangers. The resinous structure of necessity is resistant to strong acids, bases, oxidizing, and reducing agents, and most of the common organic solvents. An idea of the stability can be gaged from the fact that resins last for many years under constant use without detectable chemical or physical breakdown. The ion exchange reaction is not confined to the surface of these synthetic resins. Its porous structure permits active groups in the center of a particle as well as those on the surface to remove ions. A high capacity resin such as Amberlite IR-120 will remove up to 3.3 lb Cu per cu ft of resin. In this investigation several approaches to the problem of separating copper from zinc by ion exchange were considered. First, if a reagent could be found which would complex one of these metals and not the other, then by passing this reagent through a bed of exchanger containing copper and zinc, the

Jan 1, 1952

By A. G. Starliper, H. Kenworthy, A. Ollar

Vapor pressure determinations were made on synthesized germanium sulfides. Germanium and cadmium were removed from sphalerite concentrates by fuming. The fume was retreated to separate some of the cadmium from the germanium and, at the same time, upgrade the germanium to more than 5 pet content. MANY sphalerite concentrates contain certain impurities which have economic value as byproducts. These may include the volatile sulfides of germanium, cadmium, and lead. The objectives of the research reported in this paper were to study the fundamental volatility characteristics of germanium sulfides, to increase the recoveries of ger-

Jan 1, 1957

By M. H. Caron

THE most outstanding property of ammonia liquors, used in the ammonia leaching process is their very limited ability to dissolve all compounds present in reduced ore except nickel and cobalt. Although they do have such a high degree of purity, even the smallest amounts of impurities contaminate the precipitate of basic nickel carbonate that may be obtained from pregnant liquors by straight distillation. Figures have been given in a separate paper regarding the extent of such contamination. The product of straight distillation is likely to contain small amounts of Fe, Mn, MgO and SiO2 as well as some sulphate and sulphide. The sulphur can be readily eliminated by calcination of the product at the proper temperature and MgO and SiO2 by reduction and melting of the metal with a suitable flux. After such treatment the metal is relatively pure, and the iron and manganese content will be very small. The cobalt content, however, may vary considerably, depending upon the ore treated. The metal obtained from pure true garni-erite ores usually has only a small cobalt content of less than 1 pct. Metal obtained from medium grade iron-rich nickel ores may show cobalt values from 2 to 3 pct, and the alloy obtained from laterite is likely to contain as much as 10 pct cobalt. By proper treatment a good deal of cobalt may be recovered from lateritic nickeliferous iron ores, and cobalt will become the major constituent of the pregnant liquor if asbolan ores or similar products are treated. The pregnant liquor of "run of mine" nickel ores may have a pinkish shade, indicating the presence of cobalt. It is evident that from such liquors the metals should be recovered separately. Even if cobalt is present in only very small amounts, it would probably be economically justifiable to recover both metals as pure as possible if a suitable process could be devised. The author has made investigations along this line and has patented some processes adapted to the treatment of this type of solutions. Selective Dissolution of Nickel from Basic Nickel Carbonate Containing Some Cobalt: Basic nickel carbonate obtained from true garnierite ores by straight distillation of the pregnant liquors, always contains some cobalt as well as the normal impurities. In. order to improve the quality of the nickel product and to recover most of the cobalt, the following process has been devised. By using liquors with a low CO2 to NH3 ratio, nickel can be redis-solved preferentially to cobalt. It is not a sharp and clean separation but a selective one, for the bulk of the nickel may be redissolved with a small amount of cobalt, and a small residue may hold the bulk of the cobalt. The greatly increased cobalt content of the residue is indicated by a pronounced olive green color, in contrast with the light green color of pure basic nickel carbonate. The following example is given from Dutch patent No. 52788, Klasse 40a. 43 granted June 17, 1942: The original precipitate contained about 0.55 pct cobalt calculated on total nickel + cobalt. Eight hundred and fifty grams of the basic nickel carbonate were redissolved in leach liquor containing 7.12 pct NH3 and 2.12 pct CO2. The weight of the dry residue was about 3.5 pct of the original weight. By analysis it was found that the residue contained: Fe 1.93 pct, Co 6.01 pct, Ni 34.87 pct and also a certain amount of silica. The clear filtered blue liquor was distilled and the precipitate of basic nickel carbonate from this analyzed: Fe 0.008 pct, Co 0.0146 pct, Ni 42.37 pct. It is obvious that this product is considerably more pure, since calculation shows that about 94 pct of the original cobalt remained in the residue. Cobalt and nickel can be recovered by further

Jan 1, 1951

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By G. T. Engel, W. G. Gruzensky

Jan 1, 1960

By J. I. Budnick, W. B. Ittner III, D. P. Seraphim

A reliable technique has been developed for producing single crystals of tantalum in the form of small diameter wires. By suitably heat treating these and polycrystal samples, first in an oxygen atmosphere and finally in vacuum, it has been found possible to reduce residual resistivities to 10-3 microhm-cm. The purity of these samples is thus comparable to the purities obtained in zone-refined silver, copper, and aluminum. THE growth and purification of pure single crystals of the transition metals is, in general, difficult. The high melting and annealing temperatures of these metals make it necessary to employ rather special techniques in any crystallization process. In addition, the transition metals show a great affinity for and are easily contaminated by nitrogen, oxygen, and carbon. Recently, however. a number of investigators have been successful in growing,

Jan 1, 1961

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

PRIMARY products of the Josephtown smelter are zinc metal of various grades, lead-free zinc oxide pigments, cadmium metal, and sulphuric acid. Zinc concentrates of domestic and foreign origin are blended and desulphurized at the roaster plant. The equipment includes five, 12-hearth Herreshoff roasters and two modified Trail-type suspension roasters. The sulphur dioxide containing gases from the roasting operation are diverted to a four-unit contact acid plant for the manufacture of sulphuric acid. The roasted calcines are agglomerated by sintering on Dwight-Lloyd-type sintering machines; the sinter is crushed and sized within required limits; and the sized sinter is smelted in vertical shaft-type electro-thermic furnaces. Of the 13 electrothermic furnaces of various sizes now in operation, four are designed to produce American process zinc oxidc of various specifications; and the remaining nine furnaces are equipped with vacuum-type condensers and produce zinc metal. Papers describing the general smelting practice at Josephtown have been published by AIME. Since both High Grade zinc metal and lead-free zinc oxide pigments are produced direct from the electrothermic furnaces without need for subsequent refining, the elimination of impurities such as lead and cadmium has to be accomplished during roasting and sintering operations. To effect the producing of both High Grade and Prime Western zinc products, the roasting and sintering operations are on two separate circuits. A High Grade circuit produces finished sized sinter low in lead, cadmium, etc., for the High Grade furnaces; and the Prime Western circuit produces finished sinter destined for the furnaces producing Prime Western metal. Sintering at the Josephtown smelter differs in many important respects from the sintering practice in smelters operating horizontal retort zinc furnaces. Requirements of the electrothermic smelting furnaces define the physical characteristics of the sinter, while the chemical composition of the sinter is controlled according to the grade of metal and oxide to be made as final products. Three principal objectives in the sintering process at Josephtown smelter are: 1. To transform the zinc calcine from the roasting operations into a hard, yet porous agglomerate that will not crumble in the smelting furnace. 2. Crushing and sizing of the sinter to obtain a proper screen analysis which is normally —% in. down to +1/4 in. particle size. 3. To eliminate, particularly in the High Grade circuit, as much of the impurities such as sulphur, lead, and cadmium as possible. The sintering plant as originally built in 1930 was equipped with three standard 42 in. x 44 ft Dwight-Lloyd sintering machines. Each machine was equipped with a 15x60 in. sintering corporation fan driven by 150 hp, 900 rpm synchronous motor through a magnetic clutch and capable of delivering 30,000 cfm of air at 15 in. of water and 150°F. Each sintering machine was driven by 7½ hp dc motor with controllers for varying the speed of the machine from 8 to 32 in. per min. The pallets were cast iron and the grates of the herringbone type. The charge was mixed in a 4 ft diam x 8 ft Stehli pugmill and transported by belt conveyor, elevator and tripper conveyor to a small bin over each machine. Shortly after the start of operations the following changes were found necessary: 1. The herringbone grates which plugged very quickly and were difficult to keep clean were replaced by straight, narrow cast-iron grate bars running at right angles to the travel of the pallets. These grate bars are held in place by a center bar extending across the pallet on the 24 in. dimension and by removable retaining plates which form the sides of the pallets. 2. Mechanical grate knockers were developed in conjunction with new grate bars for continuously and automatically cleaning the grates. 3. As the cast-iron pallets cracked, they were replaced with cast-steel pallets. In 1938, the capacity of the sinter plant was increased with the installation of two 42 in. x 22 ft machines which were brought from the company's Herculaneum lead smelter. With a circulating load of some 250 to 300 pct, production of finished sinter on the 42 in. x 44 ft machines at this time amounted to about three tons of sized sinter per machine hour. In 1945, one of the 42 in. x 22 ft machines was replaced by a 60 in. x 44 ft machine of our own design. In 1948, as part of the plant-wide expansion program, the sinter plant not only was expanded but also divided into two separate plants; namely, Prime Western and High Grade circuits. The sinter destined for furnaces producing Prime Western zinc metal is made in a new plant comprising two 60 in. x 44 ft Dwight-Lloyd-type sintering machines, each having a 45,000 cfm Sturtevant fan at 18 in. water static pressure and served by an 8 ft diam x 12 ft long rotary charge pclletizer and auxiliary crushing and sizing equipment. The sinter destined for furnaces producing High Grade zinc metal and zinc oxide pigments is produced in the old sinter plant which was expanded to accommodate four of the 60 in. x 44 ft sintering machines, replacing the old sintering units. In the High Grade sinter circuit, two units of the 60 in. x 44 ft machines are used as preliminary soft sinter machines; and the remaining two units of the 60 in. x 44 ft machines are used to make finished hard sinter. Purification Theory Partial elimination of lead and cadmium in the sintering of zinc ores is common knowledge. However, by some manipulation and by taking advantage of the double circuit, it is possible to make zinc sinter which is nearly free of contaminators. Lead

Jan 1, 1952

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

R. E. Powers (Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,' which had been used since the early 1930's by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell's plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell's practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By J. D. Edwards, C. S. Taylor, A. S. Russell

Solubilities and densities are reported for alumina hydrates in NaOH solutions under the conditions of the Bayer process employed to purify alumina for aluminum production. The equilibrium constants for reactions to form A102- accurately correlate the effects of NaOH concentration on the solubilities; the temperature coefficients of the equilibria lead to heats of solution of 7.34, 4.76, and 5.24 kcal for the a trihydrate, a monohydrate, and ß trihydrate, respectively. Moderate calcination does not change the solubility of the a trihydrate but increases that of the a monohydrate. At solution temperatures above 100°C, the trihydrates transform rapidly to a monohydrate. Hydro-thermally produced a monohydrate is the stable phase above 20°C. CORNERSTONE of the aluminum industry, the Bayer process for alumina production is based on the difference in solubility of hydrated alumina in NaOH solutions between 170" and 40°C. Solubilities and densities in this system were determined thirty years ago by M. Tosterudl under the direction of J. D. Edwards and C. S. Taylor. The solubility data, which still appear more concordant than those in the literature, are employed to sort out the complex equilibria in this system. The nomenclature for the alumina hydrates is that presented in The Aluminum Industry' and more recently summarized in Alumina Properties.3 a trihydrate is the purified phase analogous to gibbsite, a monohydrate is similarly akin to boehmite, and ß trihydrate is sometimes known as bayerite. Literature Goudriaan4 reviewed the early literature on alumina in NaOH solutions and presented data on the solubility at 30°C of several forms. The gel precipitated from aluminum sulphate or chloride with ammonia and dried at 130" to 140°C had the highest solubility but was unstable, its solubility being cut to one-tenth on standing in NaOH. The solubility of the gel was decreased one-third on calcination at 300" to 400°C, while that of the gel transformed in NaOH at room temperature to a crystalline trihydrate was unchanged on calcination. The preparation produced by slow hydrolysis of sodium aluminate solution with CO, in the air gave solubilities in rough agreement with later values for a trihydrate. The solubility of this form was increased slightly by the calcination. Fricke and Jucaitis5 extended the work to 30" and 60°C with a trihydrate. They also gave solubilities for ß trihydrate (bayerite b), although the residue belonging to the left branch of the solubility curve corresponded to a trihydrate. The residues at high NaOH concentrations were mono and trisodium aluminates, the latter being 3Na2O . AL2O3 • 6H2O. Solubilities of a trihydrate at 95°C and of a monohydrate at 150" and 200 °C come from the work of Magarchak.6 a trihydrate transformed to a monohydrate above 95°C. A few measurements on the solubility at 25°C of an alumina trihydrate prepared by slow hydrolysis of NaAIO, solutions were presented by Sprauer and pearce.? Their analyses showed the monosodium aluminate to have the composition Na2O.Al2O3-2.5H2O.

Jan 1, 1956

By E. T. Turkdogan, P. Grieveson

Molten silver is equilibrated with silicon nitride at 1400°C in nitrogen + hydrogen gas mixtures, and from the solubility data the activity coefficient of silicon is found to be 1.76 at silicon concentrations below 1 pct. Using this value, and that available from the silicon cmbide solubility measurements, together with those derived from the phase equilibrium diagvam, the activities of silver and silicon are estimated for the entire composition range. The main feature of the activity data is that there is a pronounced positive deviation from ideality. The activity of silver in molten silver containing up to 5 pct Si was determined by Schadel, Derge, and Birchenall1 by measuring the vapor pressure of pure silver and of the alloy over a temperature range of 850º to 1050°C. They deduced from their results that there is a positive deviation from Raoult's law and that the activity coefficient of silver increases with decreasing temperature. However, as pointed out by Kubaschewski and Catterall,2 their activity coefficients are much too high, giving silver activities greater than unity. At a later date McCabe and Birchenal13 showed that the previous vapor pressure data on silver4 were high by a factor of about 1.3; presumably a similar error must have occurred with the vapor pressure measurements on the Ag-Si alloys. The activities of silicon and silver calculated by tager' from the phase diagram and by Gibbs-Duhem integration, respectively, show a positive deviation from Raoult's law for silicon activity and positive and negative deviations for the silver activity. According to these computations, at infinite dilution of silicon ygi = 1.12 at 1420°C. d'Entremont and chipman6 measured the solubility of silicon carbide in molten silver at unit carbon activity; the equilibrium silicon content is found to be Nsi = 0.017 ± 0.002 atom fraction for 1420°C. Using the data of Grieveson and Alcock7 for the free energy of formation of silicon carbide from pure silicon and graphite, the activity of silicon for unit activity of carbon and of silicon carbide is asi = 0.0308 at 1420°c; therefore for the above solubility data on silver, YSi = 1.81, which is somewhat higher than that given by Hager. Use is often made of silver alloys in the measurements of activities of solutes in metals where silver has a very low solubility; in fact, Ag-Si and Ag-A1 alloys have been used in the past for such purposes. In an attempt to gain more thermodynamic data on molten Ag-Si alloys, measurements have been made in the present study on the solubility of silicon nitride in molten silver; the results on these solubilities are given in this paper together with a detailed discussion of activities of silver and silicon. SOLUBILITY OF SILICON NITRIDE The standard free energy of formation of silicon nitride is known with a reasonably high degree of accuracy. According to the measurements made by Hincke and Brantle8 and by Pehlke and Elliott,' the following are the free energy data for the standard states of solid Si3N4, liquid silicon, and Nz at 1 atm pressure:

Jan 1, 1963

By John Wulff, David A. Stevenson

The rates of solution of copper, nickel, and three copper-nickel alloys in liquid lead were studied at 527° and 727°C under dynamic conditions. The relative velocity at the solid-liquid interface was varied from 8.65 to 125 cm per sec. Analysis of the data for the pure metals indicates that the solution rate is transport corztrolled at lower velocities, but a transition to mixed control occurs at higher velocities, higher temperatures, and higher percent saturation. 1 HE present work concerns the effect of relative velocity at a solid-liquid interface on the dissolution kinetics of pure solid materials in liquid metals. This general problem is of interest in electrode kinetics, in electrolytic processes, and more recently in the field of liquid metal corrosion. Considerable work has been done on dissolution kinetics in aqueous environments because of the obvious importance to electrolytic processes.1,2 In purely metallic systems investigation has been more limited. There are, of course, extensive data from loop tests which are used in an engineering evaluation of liq- uid metal corrosion. Here, however, the dissolution process is complicated by several interdependent processes. In general, one of two factors is considered to be rate limiting in the dissolution process: the transport of material from the solid-liquid interface into the bulk liquid, or an activation process directly at the interface. A number of studies of the dissolution rates of solid metals in liquid metals under static conditions have been published.3- Since the attendant hydrodynamic conditions imposed by thermal gradient convection and concentration gradient convection are difficult to analyze, it is doubtful if a clear interpretation of the experimental findings of these papers in terms of the mechanism involved in the dissolution process can be made. A clearer picture of the dissolution process is provided by

Jan 1, 1962

By D. Cubicciotti

IT has long been known that some metals are capable of being dispersed or dissolved in certain of their fused salts.' Davy' and Bunsen³ were among the first to observe that in some fused salt electrolyses, a highly colored, strongly reducing salt phase appeared in the neighborhood of the cathode. Later workers found that the current efficiency of the electrolysis was markedly reduced when such a phase appeared. It was also found that the strongly reducing salt could be made by melting the metal and normal salt together. Chemical analysis showed that in such salts the metal ion to anion ratio was always larger than in the normal salt. From such observations arose two different explanations of the nature of metal in salt solutions. When a solution of this type is quenched, it is possible to find small globules of metal in the salt. From this and other observations, Lorenz' and co-workers assumed the metal in salt solution to be a colloidal dispersion of metal in the fused salt and called it "metallnebel" or metal fog formation. They made a number of experiments to substantiate this point of view. Another school felt that when the metal dissolved it reduced the salt partially to a mixture or solution of normal salt and subsalt. Both of these ideas could explain the strong reducing character of the salt formed and the low current efficiency of the electrolysis. If either a metal colloid or a subsalt were formed at the cathode and diffused to the anode, it would be oxidized to the normal salt. Thus a cyclic process of oxidation and reduction could be set up conducting the current without giving rise to a net change in the system. These facts led the author to investigate some of the properties of metal in salt solutions with the hope of elucidating their nature further. Among the metal-salt systems that form metal in salt solutions most markedly are the alkaline earth metal-halide systems and cerium, bismuth, and cadmium halides. Other systems of halides, oxides and sulphides form such solutions to a lesser degree. The first work undertaken was a study of the temperature-composition diagrams of some of the systems." From such diagrams it would be possible to distinguish between a subhalide formation or a colloid. A subhalide should give rise to characteristic changes in the phase diagram, while a colloidal dispersion of metal in salt would not alter the freezing point of the salt. The results obtained on a number of alkaline earth metal-halide systems were all quite similar. Fig. 1 shows the barium-barium chloride system. The other

Jan 1, 1954

By Renato G. Bautista, Robert A. Hard

A comparative study has been made of the ex-tractability of several of the transitim metals from thiocyanate sohtions using methyl isobutyl ketone as the organic solvent. Extractions were made of scandium (III), chromium (III), manganese (II), iron (III), and cobalt (II), of which only the scandium , iron, and cobalt were readily extracted. All extractions were made at pH 2 and at 25.5 °C. A series of extraction experiments was made on scandium, iron, and cobalt to determine the effect of thiocyanate cmcentration added as the ammonium and also as the calcium salt. Also determined was the effect of metal ion concentratim and ionic strength on the distribution ratio. Analyses of the organic extracts indicated the scandium and iron were extracted principally in the uncharged trithiocyanate form, while the extractable form of the cobalt contained the cobaltotetrathiocyanate anion. THE chemical separation of metal complexes in solution by solvent extraction has in recent years been developed for large scale separation as well as bench scale work in the laboratory. It has also found increased application in analytical chemistry. Its extension to extractive metallurgy as a unit operation is best illustrated in the recovery of uranium and vanadium from their leached liquor.5-8 The extractability of some thiocyanate systems have been extensively investigated. The rate earths have been separated from one another using butanol as a olvent. Scandium was effectively extracted in ethyl ether using ammonium thiocyanate as the com-plexing agent.'' Similarly, the separation of hafnium from zirconium has been reported using ether""' or hexone13 as the organic solvent. The extractability of various metal thiocyanates in ethyl ether is given by 0ck.l Sharp and Wilkinson15 prepared nickel-free cobalt slats by thiocyanate extraction. The mechanism of extraction of titanium (IV) thiocyanate with methyl isobutyl ketone was determined by elafosse.''" The characterization of cobalt (TI) thiocyanate complex using methyl isobutyl ketone as the solvent at near neutral aqueous solution and the spectrometric studies of the ex-tractable cobalt complex has been made by Hard." It is noteworthy to mention at this point that the fundamental characteristic of ketone (oxonium) solvent extraction is that the extractable species are uncharged ion pairs solvated by the ketone molecules, but probably still partially hydrated.

Jan 1, 1963

By G. V. Jere, C. C. Patel

Chlorination of the various constituents of ilmenite by different chlorinating agents in presence of various reducing agents, have been considered on the basis of the standard free energy and standard enthalpy changes as a function of temperature. The standard free energy change considerations show that it is beneficial to chlorinate ilmenite by chlorine in the presence of carbon and also that iron constituent of ilmenite can be preferentially chlorinated by clzlorine, titanium tetrachloride or their mixture. These findilzgs have been corroborated from the published work. METALLURGICAL processes involving the use of titanium tetrachloride have gained in importance because of the use of the latter in the manufacture of titanium metal. Since ilmenite is more abundant in nature than any other titanium mineral, the future of the metallurgical processes depends on the utilization of ilmenite for the production of titanium tetrachloride. In these laboratories, investigations have been carried out on the chlorination of ilmenite under a variety of conditions.1'2 During these studies, it was noticed that 1) preferential chlorination of iron was effected at low temperatures (400° to 600°C) and at low carbon content (6 to 7 pct), 2) carbonyl chloride retarded the chlorination of iron oxides and titania perceptibly, while 3) carbon-tetrachloride, compounds of sulphur and some other catalysts favored the chlorination. Moles3 has found that oxides of iron are chlorinated in preference to titania at high temperatures, while wilcox4 has claimed the preferential chlorination of titania between 1200" and 1500°C. It has been shown in this paper that preferential chlorination of titania claimed by Wilcox is not likely to occur. Daubenspeck and coworkers5,6 have claimed the preferential chlorination of iron by chlorine or by a mixture of titanium tetrachloride and chlorine between 700° and 1050°C in the absence of carbon. Even when plain titanium tetrachloride is employed as the chlorinating agent, pascaud7 noticed the preferential chlorination of iron and other oxides. The purpose of this paper is to explain from thermodynamical considerations, the various chlorination reactions studied so far. ILMENITE CONSTITUENTS AND THEIR CHLORINATION PRODUCTS Although the general composition of the ilmenite mineral is represented as FeTiO,, most of the ilmenites found in nature have variable quantities of TiO2 (44.6 to 64 pct), FeO (4.7 to 36 pct) and Fe2O3 (6.9 to 28 pct).8 The higher content of ferric iron in ilmenites was attributed by Millerg to the presence of arizonite (Fe2O3.3TiO2). But the X-ray studies by Overholt, Vaw, and odd" have shown that arizonite is a mixture of haematite, ilmenite, anatase, and rutile. Except for the anatase, similar views have been advanced by Lynd, Sigurdson, North, and Anderson8 from magnetic, X-ray, and optical and electron microscope studies. The ilmenite ores can, therefore, be assumed to consist of mineral aggregates of ilmenite, rutile and haematite. From the free energy of formation of ilmenite (FeTiO3), it has been shown by Kelley, Todd, and King11 that ilmenite is stable even up to its melting point (1367°C) and would not undergo decomposition into its constituent oxides. Schomate, Naylor, and Boericke12 have found that in the presence of a reducing agent the iron constituent of ilmenite is selectively reduced. The reaction of chlorine with ilmenite in presence of a reducing agent can, therefore, be synonymous with that of the reaction of chlorine with the constituents of ilmenite, viz., TiO2, FeO, and Fe2O3. Most of the reaction products of chlorination of ilmenite in the presence of reducing agents will be in equilibrium with their dissociation products, depending on the temperature. The titanium tetrachloride is, however, quite stable up to 1500°C due to its covalent nature. The equilibrium for the ferric chloride system has been investigated by Kangro and Bernstorff, 13, schafer14 and Kangro and petersen,15 and the results are summarized in Fig. 1, curves a, b, and c respectively. From these results, it is clear that the ferric chloride disociates as follows: 324° to 700°C FeaCl6(g) ?2FeCl2(c) + Cl2(g) [1] 324°to 900°C Fe2Cl6(g) =2 Fe Cl2 Reaction [I] (curve a) occurs in the forward direction to about 6 pct at 400°C but falls off very rapidly with increase in temperature and beyond 600°C, it is practically negligible, perhaps due to the formation of the stable monomer, FeC13(g). As the temperature is further increased, the amount of FeCl,(g) in-

Jan 1, 1961

By I. Nilsson, G. Sundkvist, A. Danielsson

A spectrochemical method of slag analysis is descibed which utilizes fusion of the sample with a flux, then cooling and crushing to put all samples into a common form. The powder, is then fed onto adhesive tape and passed through a spark by means of a special device to provide very reproducible discharge conditions. Combined with a direct-reading optical emission instrument, this system provides speed and accuracy of antilysis heretofore unobtainable for. slag samples by any other method. THERE are many suggested methods for spectro-chemical analysis of slags. The most important are fusion-pellet methods and solution methods. In our company the fusion-pellet method has been used earlier, and is described by Lounamaa. W. H. Tingle and C. K. Matocha have made refinements of the pellet method.' A Committee of the British Iron and Steel Research Association has investigated different methods of spectrochemical analysis of slags. Its purpose was to formulate a method which would give the complete analysis in 30 min with an accuracy of ±3 pct. The committee recommends a solution technique, which was thought to correspond best to their requirements. The method to be described is a fusion-tape method. The sample is isoformed by fusion and grinding. The powder is analyzed with the tape technique. The tape machine and some of its applications are described earlier.4'5 The powder to be analyzed is continuously fed onto a moving adhesive tape, which passes through the spark gap. The sparks break through the tape and vaporize and excite the material to be analyzed. The most outstanding feature of the tape machine is its very high reproducibility. The concept of isoformation has been introduced earlier.= It means a pretreatment of the samples to make them uniform from the spectralanalytical point of view, i.e., cancelling systematic differences between the samples. The purpose of the isoformation is to reduce the influence of particle size, as well as chemical and mineral composition. Before describing the isoformation by fusion plus grinding, which is the purpose of this paper, a few words will be said about two other types of isoformations, i.e., grinding with buffer and ion exchange plus grinding as they have been considered during the application of the tape technique for slag analysis. Grinding with buffer might be a sufficient isoformation in some special cases, where the mineral composition is defined. The time of grinding must, however, be rather long, at least 5 to 10 min, even when using such an efficient mill as the Swing Mill from Messrs. Siebtechnik, Mühlheim, Germany. This type of isoformation is not recommended due to its limitations and due to the fact that the gain in time compared with the fusion technique is almost negligible. The principle of ion exchange plus grinding and some of its applications have been described.5 The following elements of interest in slag analysis can be determined in this way: Na, K, Cu, Mg, Ca, Ba, Zn, Pb, Al, Cr, Mn, Fe, Co, Ni. The very important element Si, however, cannot be analyzed with this method. Although the ion exchange isoformation for slag analysis cannot be looked upon as a routine method, it can be used for

Jan 1, 1962

By I. Cadoff, E. Miller, K. Komarek

Jan 1, 1960

By B. Russell, J. R. Tuffley

The stability regions of the normal sulfate and the various basic sulfates of lead in 02-SO2 and PhS-SO2 gas atmospheres were calculated from available thermodynamic data over the temperature range 600o to 1200oC. Roasting experiments were carried out on samples of synthetic lead sulfide at various temperatures and for various roasting times. Compounds in the oxidized surface layers were identified by X-my techniques. The order in which the various reactions occurred was determined by considering the experimental results in conjunction with the thermodynamic calculations. The results of these investigations were applied to the sintering of lead sulfide concentrates, and the extent to which each of the various reactions occurred in a sinter bed was determined. PRODUCTS which may be formed during the roasting of PbS are PbS04, PbSO4. PbO, PbSO4 . 2PbO, PbSO4 . 4PbO, PbO, and Pb.1, 2 The formation of some sulfates has been studied by a number of investigators3-' whose experiments have mostly been confined to the temperature range between 500" and 850°C. Culver, Gray, and spooner3 were able to isolate the reactions which formed PbSO4 and PbSO4. PbO by carefully controlling the compositions of the roasting gases. The kinetics of these reactions were studied within the temperature range 673" to 807°C. Gardner4 and Merrick5 also studied the kinetics of oxidation of PbS. Gardner disregarded the existence of basic sulfates and, as a result, misinterpreted some of his experimental data. Merrick recognized that most of the products of oxidation were mixtures of basic sulfates, but was unable to identify the individual components. Hoschek6 oxidized PbS in air at temperatures up to 800°C. The products were analyzed after roasting had proceeded for some minutes, but no attempt was made to follow the reactions in the initial stages. Consequently, no roasting mechanism was derived. He also showed that PbSO4 and PbSO4 - 4PbO decomposed slowly in air at temperatures in the region of 800°C. The stability regions of sulfates in the temperature range 500" to 850°C have been only partially determined, while practically no information is available for higher temperatures. In the lead sintering process, PbS concentrates are roasted at temperatures within the range 1000o to 1200°C. In order to investigate sulfate formation, it is necessary to determine the effects of temperature and gas composition upon the various oxidation reactions and upon the regions of stability of the various lead sulfates. Kellogg and Basu2 introduced an equilibrium diagram similar to those in Figs. 1 to 3 which provides a convenient medium for represent-

Jan 1, 1964

By W. H. Porter, M. E. Wadsworth, J. R. Lewis, K. L. Leiter

The oxidation of Cu2S in oxygen and the sulfating of Cu2O in oxygen-sulfur dioxide atmospheres was carried out under a variety of conditions. The oxidation of Cu2S was found to be retarded by entrapment of SO, and O2, which stabilized internal sulfates for long periods of time. The course of the reaction was followed by measuring weight changes and also by SO, evolution. Sulfating of Cu2O was a maximum at ratios of SO, to O2 approximating maximum SO, production. At elevated temperatures SO, was found to increase the rate of oxidation of Cu2 O to CuO even though sulfates did not form. All sulfating reactions followed the parabolic rate law indicating diffusion. MANY studies of the roasting of copper sulfides have been reported in recent years. Diev et al.1 investigated the roasting of chalcocite (Cu2S) in air, and oxygen enriched air. Lewis et al.2 also studied the oxidation of natural and synthetic chalcocite in air and oxygen atmospheres and their studies indicated that the maximum formation of water soluble sulfates occurred at approximately 450oC. Ashcroft3 reported that oxide production during the roasting of chalcocite resulted only from secondary decomposition of sulfates which were formed as primary products. peretti4 refuted this claim by showing that a layer of Cu2O appeared directly adjacent to the Cu2S during roasting of cylindrical briquettes of cupric sulfide, CuS. The linear advance of the Cu2S-Cu2O interface was used as a measure of the kinetics of the roasting reaction. The reactions proposed were: 2 CuS—Cu2S + 1/2 S2 [4-1] 1/2 S2 + O24 SO2 [4-2] cuzs +3/2 O2 4 Cu2O + SO2 [4-3] cu2o + 1/2 O2—2 cuo [4-4] At temperatures above 663oC, CuO was the only final solid phase reported. Below 663" C increasing amounts of sulfate were found mixed with the CuO. McCabe and Morgan5 investigated the roasting of discs of synthetic chalcocite and reported the following sequence of products beginning at the sulfide surface: Cu2O, a mixture of Cu2O and CuSO4, Cum,, CuO . CuSO4, and CuO. The principal reactions were reported to be: Cu2S + 3/2 O2-Cu2O + SO2 [5-1] CU2O + 2 SO2 + 3/2 O2—2 CUSO4 [5-21 2 CUSO4— CUO . cum, + SO3 [ 5-31 cuo . cuso4—-2 cuo + SO, [ 5-41 Eq.15-11 supports the claim of Peretti, Eq. [4-31, that CuzO is formed directly from Cu2S rather than as a secondary product from a sulfate as suggested by Ashcroft. On the other hand CuO was found to form as a secondary product from the decomposition of copper sulfate and basic copper sulfate, Eqs. [5-31 and [5-41. The formation of sulfates was explained by McCabe and morgan5 to be a direct reaction of Cu2O with 0, and SO, or SO, at distinct regions in which the partial pressures of each were such as to form the sulfate. Thornhill and pidgeon6 roasted both natural and synthetic chalcocite grains in air at temperatures between 420" and 550° C. They found a dense primary oxidation layer in contact with the sulfide. A secondary layer of porous oxidation products was found to expand with roasting time. The oxide products were leached away and the remaining core was studied by X-ray diffraction. The X-ray patterns showed an increased conversion of chalcocite to digenite with time. Digenite,7 a defect structure of cuprous sulfide, occurs naturally as Cu,-,S where x = 0.12 to 0.45, with an average analysis of Cu, ,S. The mechanism of digenite formation was proposed as: Cu2S + oxygen—Cu1-8S + 0.1 Cu2O [6-1] Cuj.eS + oxygen—0.9 Cu2S + SO2 [6-2] It is apparent from the above studies that the oxidation of Cu2S, ultimately ending in CuO, may be divided into ihree general stages (all of which may occur simultaneously): 1) primary oxidation to Cu2O; 2) secondary sulfate formation; and 3) sulfate decomposition. Consequently reactions of O2 and SO, with Cu20 constitute important aspects of the roasting of chalcocite. Virtually no studies have been made regarding sulfating reactions involving Cu,O. Mills and Evans8 noted the effect of sulfur dioxide on the oxidation of copper at low temperatures and low SO, partial pressures. They reported a measurable increase in the oxidation rate of copper when SO2, was present. Interest in the Cu2O-CuO-0, system has been limited predominantly to misciblllty studies and determinations of heats of formation by

Jan 1, 1961

By C. B. Alcock, R. G. Hudson

Sulfur pressure measurements above FeS in equilibrium with iron have been carried out by the Knudsen orifice method. A comparison is made of the weight loss of the cell per unit time obtained in the above experiments, that calculated from Richardson and Alcock's measurements of the S2 pressure above FeS in equilibrium with iron, and the dissociation constant for diatomic sulfur from spectroscopic and thermal data. EXTENSIVE equilibrium measurements have been made to determine the sulfur potentials of a great many systems of metallurgical interest.' In order to confirm their reliability, to supply data which may be of use in further thermodynamic calculations, and to establish the reliability of the Knudsen orifice in obtaining accurate thermodynamic values at high temperatures, the present investigation on the pressure of the gaseous species above FeS in equilibrium with iron has been carried out. The Knudsen orifice method has been used for these pressure measurements. Experimental The apparatus and general technique for this investigation are the same as that reported for the determination of the vapor pressure of silver.' To reduce the residual gas pressure in the evacuated chamber, a titanium getter, maintained at run temperature, was introducbed. Several types of Knudsen cells were used—platinum, zircon, and fused silica. The orifice in the zircon cell was fashioned with a small diamond wheel. The same precautions were used in this investigation as were employed in the work on Mo2S2.3 The FeS-Fe mixture was prepared by heating a sample of pure FeS,, supplied by K. K. Kelley of the Bureau of Mines, with excess iron powder, cp grade, obtained from the Fisher Scientific Co. These two substances were heated in a closed Armco iron crucible at 960°C, held in a vacuum of less than 10" mm Hg for 24 hr. The mass was then removed from the cell and ground in an agate mortar. In this form it was charged to the various Knudsen cells. Heating the Knudsen cell for an additional two days was sufficient to obtain constant rates of weight loss of the cell. The data obtained in this investigation are recorded in Table I. To establish whether or not a sulfide of iron is volatile at these temperatures, 0.7646 g of the FeS-Fe mixture, described above and containing 69.2 pet Fe, was placed in the zircon Knudsen cell. Run Nos. 103 to 109 were performed on it. After the completion of these runs, the total amount of iron left in the cell was obtained by chemical analysis. It contained 0.537 g Fe, compared to 0.529 g in the original charge. Thus, there was an apparent gain in iron of 1.5 pet. This is attributed to unknown experimental error, and the conclusion is that no sulfide of iron is volatile. The vapor pressure of pure iron4 is about one thousandth that of the sulfur pressure' at these temperatures. The vapor pressure of iron inside the Knudsen cell will be almost exactly that of pure iron, since in the iron-rich phase the percentage of sulfur is of the order of 0.025 pet.At this low percentage of sulfur Henry's law is probably obeyed by the sulfur. Thus, the iron will obey Raoult's law. In any event, the vapor pressure of iron will be lower than that of pure iron and, since the vapor pressure of pure iron is negligible compared to the pressure of sulfur, the weight loss of the cell due to the vaporization of iron should be negligible. Since neither iron nor FeS is volatile to an appreciable extent, the total weight loss of the cell must be due to the vaporization of sulfur. Discussion and Calculations On the assumption that S, is the only gaseous species present in appreciable quantity, its pressure

Jan 1, 1957