Search Documents

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining' of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally. enclosed in serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2, The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates.. The range in published figures for solubility

Jan 1, 1936

By G. Rinelli, A. M. Marabini, V. Alesse

Salicylaldehyde, a chelating agent for tin, has been found to function as a collector for the flotation of cassiterite. Infrared and nuclear magnetic resonance studies clearly show that salicylaldehyde can form a chelate compound in bulk and at the surface. Results are also given for the flotation of a tin ore with this reagent.

Jan 1, 1976

By R. W., Ludt

THE use of froth flotation for the separation of minerals has become one of the most important of ore dressing processes. Its particular adaptability to the enrichment of low grade ores has made the process an important factor in the national economy. The methods have been extended to the recovery of a great number of minerals. Among the few minerals which have resisted efforts toward industrial flotation is chrysocolla, a hydrated partly colloidal copper silicate. Chrysocolla, being a product of natural oxidation, has been found to occur in small quantities with many ores which are recovered by flotation methods. In present practice, these small quantities of copper silicate pass off with the tailings and are lost. The advantages to be gained by a satisfactory process for the recovery of chrysocolla is apparent. Any application of principles which points a way toward the satisfactory industrial flotation process for copper silicate would be of advantage. This paper presents an attack on this problem.

Jan 1, 1949

By W. J. McKenna

THE International Smelting Co. concentrator at Tooele, Utah, first operated on a custom basis for the treatment of lead-zinc-iron ores on Nov.' 1, 1924, with a capacity of 500 tons per day. On May 1, 1925, the capacity was increased to 1000 tons per day by the addition of another 500-ton section. The concentrator has since operated on the two-section basis, each treating 500 tons per day entirely by flotation. LABORATORY AND TEST MILL In connection with the concentrator, a well-equipped laboratory and small continuous testing plant are maintained. The flotation equipment in the test plant is of both the Callow and Mineral Separations Sub-"A" types, so that actual concentrator conditions may be duplicated as closely as possible. PURCHASING OF ORE A new shipper usually sends to the plant a 25 to 50-lb. sample, representative of the ore to be shipped. Batch flotation tests are made on this sample to determine its amenability to the concentrator treatment flowsheet and reagent combinations. The results of these tests, which are accurately correlated with those obtained at the concentrator, both as to grades of products and recoveries, determine the actual value of the ore as submitted in the ore purchasing department's treatment schedule. Hearty cooperation has existed at all times between the ore purchasing and operating departments in the selection of ores as concentrator feed. ORE TREATED The basic tonnages for mixtures on the two sections come from the Park City and Bingham mining districts. The Park City tonnages are received by rail and consist of crude ores and gravity mill products. Those from the Bingham district are received by rail and aerial tramway,

Jan 1, 1928

By R. G. Weavind

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry.

Jan 7, 1951

By R. W. M. Lai

INTRODUCTION Manganese nodules were first discovered by the H.M.S. CHALLENGER expedition of 1873-76 and have engaged the interest of oceanographers and natural resources engineers ever since (1-4). Manganese nodules, some of them as large as grapefruit, cover vast stretches of the ocean floor throughout many parts of the world. In some areas the ocean floor is literally paved with nodules. The Pacific Ocean alone is estimated to contain 1.5 trillion tons of nodules which are forming at the rate of about 10 million tons per year (2). An analysis of the principal metal values for Pacific Ocean nodules is shown in Table I (5). [ ] The principal ingredients of the nodules are manganese and iron, but they also contain other important associated metal values such as copper, nickel, cobalt, and molybdenum. These associated metal values,

Jan 1, 1980

By Mi Chung

T HE ore-dressing problem at Tul Mi Chung is complicated by the unusually complex nature of the ores. These come from replacement ore- bodies in limestone at the contact with a granite batholith, and contain copper, gold, silver, bismuth, molybdenum, iron, arsenic, zinc, and lead, the first two metals constituting the principal sources of profit. Iron is present as pyrite, magnetite, and hematite. Arsenic occurs both as mispickel and lollingite (FelAsa), the latter carrying a certain amount of finely divided gold. The gangue minerals are those typical of limestone con- tact-metamorphism and include a large percentage of garnet, together with diopside, serpentine, calcite, epidote, zoisite, actinolite, 'mica and other minerals. A part of the gold occurs in a free state; some is combined with chalcopyrite and lollingite, and a consider- able proportion is contained in the pyrite. Researches towards the improvement of recovery have been energetically conducted since 1915. Amalgamation, gravity concentrating tables, vanners, can- vas plants, etc., have all been tried and discarded in favor of flotation. It was very quickly established that fine grinding was essential for satisfactory recovery. This was and is still accomplished in Hardinge ball and pebble mills. A comparative test showed that when the ore was crushed to the point at which it contained 20 to 26 per cent. coarser than 100 mesh, the gold recovery was only 55.9 per cent., whereas when crushed so that only 11 to 15 per cent. was coarser than 100 mesh, the gold recovery was increased to 82.5 per cent. No particular difficulty was ever experienced in making a satisfactory recovery of copper but the losses in gold were considered serious and led to the investigation described in this paper.

Jan 1, 1924

By Herbert H. Kellogg

DEPOSITS of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (-325-mesh) sand assaying 95.5 per cent Si02, and a very fine (-3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. EXPERIMENTAL PROCEDURE The Sample.-The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.-By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fraction was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper.

Jan 1, 1945

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

By Howard R. Keil

PRIOR to World War II, approximately 500 tons per day, or one-third of the ore being shipped to the Golden Cycle Mill at Colorado Springs, Colo., from the Cripple Creek district, was being treated in the flotation plant. The remaining 1000 tons, along with the flotation concentrates, received the usual roasting and cyanide treatment. Since it was not possible to make a disposable tailing on the general run of Cripple Creek ores by flotation alone, it was necessary to treat the flotation tailings by cyanidation, along with the roasted ore. By this treatment, an overall economical tailing could be made. The gold ores from the Cripple Creek district are the highly siliceous sulphotellurides with approximately 3 pct total sulphides. In the lower grade ores most of the values are found in very finely disseminated pyrite. In some of the higher grade ores the tellurides, calaverite and sylvanite, can be recognized. After several years of floating Cripple Creek gold ores, having a very low mineral content, it was concluded that this type of ore required a Type of flotation machine that would give a rather violent aeration and agitation. This action produced a fairly deep froth column which contained not only the free mineral, principally pyrite, but also most of the middling product; this was most essential in producing a low grade tailing by flotation alone that could be discarded to waste. After investigating most of the current types of flotation machines, it was decided to convert to the Fagergren type. During World War II, the flotation plant was modified to handle lead and zinc ores. The treatment of these ores was carried on until April 1946. At this time the flotation plant was again reconverted to handle the Cripple Creek ores. SELECTING ORES FOR FLOTATION During the period of reconversion a considerable amount of experimental work was carried on in the laboratory to determine if a disposable tailing could be made by flotation alone, on certain selected ores from the Cripple Creek district. It was found that most of the dump ores and a few of the low grade mine ores could be treated by this method with very satisfactory results. After the preliminary test work in the laboratory, it was decided to carry on further work on a plant-size scale to see if similar results could be obtained. On April 15, 1946, a part of the plant was put into operation as a pilot plant. The various ores that had been found suitable for treatment by this method in the laboratory, were run through the pilot plant at the rate of 200 tons per day for a period of several months. Results were so encouraging that it was decided to put the plant in full-scale operation. Since that time plant capacity has been increased from 500 to 1000 tons per day. This has been done not by the installation of more machinery but by (I) crush-

Jan 1, 1947

By A. M. Gaudin

The flotation process has been applied extensively in the mineral and chemical fields. This paper reveals results obtained by an exploration of an application to the biological field. In many ways this study was indeed an exploration since so many factors are different. In the mineral field, the particles, both those floated and those not floated, cover a wide range of sizes and shapes; in the biological field, the particles of one population are primarily of one or two sizes and one or two shapes. This identity in size and in shape gives biological systems the advantage of homogeneity. In the mineral field the particles may be as coarse as a millimeter; in the biological field the size may be a micron, or less. In the mineral field the particles may have a gravity several times that of water so that their apparent gravity is quite substantial. Microorganisms, on the other hand, may have a gravity so near that of the liquor that their settling velocity in the liquor is vanishingly small. These two facts conspire to make bubble-particle encounter in the pulp-body less likely. Finally, microorganisms are living, reproducing, and dying-all of which does not help the experimenter get a balance of materials. The analytical problems, too, are extraordinarily difficult, for the organisms can contain only elements that occur in their environment, although at a different level of concentration. The chemical composition of the surface of microorganisms is readily altered. In spite of these areas of difficulty, microorganisms can be floated to leave practically water-clear tailing, they can be floated from each other and, in fact, the same organism can be fractionated into a float that differs from the sink. SIZES AND SHAPES OF ORGANISMS Most ore pulps are described with reference to the percentage of the pulp that is fine enough to pass a 200-mesh sieve. Thus a copper-ore pulp may be 80% -200 mesh. Since 200 mesh equals 74 µ, a 2000-mesh particle would be 7.4 µ in diameter, and a 20,000-mesh particle would be 0.74 µ. The microorganisms with which this work is concerned are of the order of magnitude of 20,000 mesh. We have worked with Escherichia coli, the colon bacillus, Bacillus cereus, Bacillus subtilis, Bacillus megaterium, and Serratia marcescens. In some pioneer work, Dognonl,2 reported the use

Jan 1, 1962

By K. V. S. Sastry

INTRODUCTION Flotation is by far the most important unit operation of mineral processing. Most of the common base metals are produced from flotation concentrates of metal sulfides. Flotation is proving to be a valuable process for producing non-metallic minerals such as ceramic oxides, silicates, clays and phosphate fertilizers. All these fltation separations are carried out on materials which are predominantly in the 10 to 100 micronssize range. The present practice of flotation circuits for the production of large tonnages of metallic and non-metallic mineral concentrates is fairly well understood, developed, and standardized. Two kinds of problems are encountered (1, 2) with fine particles smaller than 10 microns. First is the interference of the fine particles with the flotation of the coarser particles and the second is the poor flotation behavior of fine particles. In general, these problems are handled either by eliminating, minimizing, or ignoring the fines in the flotation circuit feed. In recent years, however, a considerable number of experimental and theoretical studies have been carried out to understand the flotation behavior of fine particulates. This literature is summarized in four review papers (2-5). Application of the conventional flotation techniques for the separation of mineral fines is known to be uneconomical, and to present several scientific and technological problems (1-5). The objective of this presentation is to examine the flotation behavior of fine particles in terms of their physical-chemical properties and to review the potential techniques of fine particle flotation. Specific reference to the problem areas and research needs will also be included in the discussion.

Jan 1, 1979

By E. S. Leaver

THE amount of gold that occurs in a ton of milling ore from most of the large-scale copper mines is so small that unusual care and special attention are necessary to recover it. In some cases the gold is not considered important enough to warrant daily assays of the various products. Considering the large tonnage of copper ores that are now concentrated by flotation, as computed in a recent review, the gross gold content is surprisingly large, probably amounting to over 10 million dollars per year in the United States. The indications are that in many of the copper-milling operations with gold content under $1 per ton, only 50 per cent. of the gold is recovered in the flotation concentrates. Lime is generally used as a depressant for pyrite in the flotation circuit. The authors have shown that high lime or a solution high in calcium ions is also a depressant for gold. Their experiments on several well-known ores show that by careful regulation of the alkalinity of the mill solutions, a higher flotation recovery of the gold can be obtained, together with equally good copper recovery in a good grade of copper concentrates. In cyanidation for the recovery of gold, the best accepted practice demands that the mill solutions be tested and regulated by simple chemical reactions at definite periods during treatment or with each change in the treatment. It is similarly important for the recovery of gold that the solution in the flotation circuit be analyzed for calcium ions at regular periods and at each step in the flotation practice. The lime should be added when and where needed and not in excessive amounts at the head of the mill.

Jan 1, 1931

By J. E. Papin

Morenci ores contain as an average about 0.015 pct molybdenite, MoS2. Incidental to the concentrating operations applied for the recovery of copper minerals, approximately two-thirds of the molybdenite is floated and appears in the final copper concentrate. The economic importance of molybdenum and the success achieved in its recovery in milling operations elsewhere encouraged research directed toward its recovery in marketable form. Several procedures are utilized to effect separation of molybdenite from copper and iron sulphides, but only two have wide application. In the better known of these two methods the molybdenite in the copper concentrate is depressed in a flotation operation using soluble starch as the depressant. The tailing from this treatment thus becomes a low-grade molybdenite concentrate which after thickening, filtering, and low temperature roasting is repulped with water and subjected to additional flotation steps for recovery of the molybdenite. A thio-phosphate collecting agent is employed in flotation of the copper minerals. Presumably the stability and lasting effects of that collector type necessitated the practice of depressing molybdenite followed by subsequent roasting to insure elimination of copper and iron sulphides from final molybdenite concentrate.

Jan 2, 1955

By R. A. Pallanch

IN his recent paper, "The Controversial Art of Flotation," (Mining Technology, March, 1944) E. H. Rose states that "flotation is a science in so many variables that only art can blend them." This statement is apt. It contains meat. In other words, a valid scientific reason is behind every flotative effect. Some of these reasons we understand, but much the greater number of them still escape us. This does not prevent us from "going places," as familiarity and experience with the problems result in an increasingly intelligent and artful handling of these effects. Hypotheses are built up by the individuals concerned to explain certain happenings. Many of these hypotheses have to be abandoned when placed under the glaring scrutiny of actual trial. A few survive the severest of tests, come through unscathed, and are elevated to the rank of theories, something susceptible of certain chemical and physical explanation, under the conditions of the particular plant concerned. If these theories continue to hold water under all the variations existing in most milling plants, they gradually become accepted as facts in the minds of the plant operators. But-and here is a big BUT-these so-called facts may fall down completely in another plant working under an entirely different set of conditions. In other words, each plant tends gradually to build up its own facts, which may or may not be facts at another operation.

Jan 1, 1945

By A. W. Hahn

ALTHOUGH enormous tonnages of sulfide lead and lead-silver ores are treated by flotation, the products of flotation mills treating oxidized ores of lead and silver are almost negligible. However, each year there is a slight tonnage increase, and it is possible, should a sizeable oxidized lead ore tonnage be developed, the field will become an important one. In 1918, the Shattuck-Arizona Copper Co. erected a plant at Warren, Ariz., for the treatment of oxidized gold-silver-lead ores. Glenn L. Allen worked out the metallurgy for this plant, employing tabling, followed by flotation concentration. The Shattuck-Denn Mining Co., successors to the Shattuck-Arizona Co., now employs straight flotation in the same mill, treating about 200 tons daily. In 1922, the San Diego mill of the American Smelting & Refining Co., in the Parral district, Chihuahua, Mexico, started operating a 600-ton mill on a mixed sulfide-oxide gold-silver-lead ore. Tables and flotation are used here, and about 200 tons of oxidized slime treated by flotation. In 1923, the Eureka Holly Mining Co. started operating a 90-ton mill at Eureka, Nev., using tables and flotation, on an oxidized lead-silver ore. In 1924, the American Smelting & Refining Co. started a 250-ton mill in northern Peru, to treat a high-grade oxidized gold-silver ore with very low lead values. In 1924, the Grand Central Mining Co. started a 200-ton flotation mill on old oxidized gold-silver-lead tailings at Fairbank, Ariz. In 1926, the Compania Internacional Minera, a subsidiary of the Union Corporation of London, started a 250-ton flotation mill on oxidized lead-silver ores, and during April of this year, the Phelps-Dodge Corpn. will probably start a 250-ton mill at Warren, Ariz., on oxidized lead-silver ores, similar to those being treated in the Shattuck-Denn mill. METHODS All of these mills use sodium sulfide for filming the oxide minerals, with the possible exception of the North Peru mill, and all use oily reagents. The total tonnage of strictly oxidized lead-silver ores concentrated by flotation is probably less than 2500 tons daily. The following figures give the various types of ores being treated:

Jan 1, 1928

By A. W. Hahn

ALTHOUGH enormous tonnages of sulfide lead and lead-silver ores are treated by flotation, the products of flotation mills treating oxidized ores of lead and silver are almost negligible. However, each year there is a slight tonnage increase, and it is possible, should a sizeable oxidized lead ore tonnage be developed, the field will become an important one. In 1918, the Shattuck-Arizona Copper Co. erected a plant at Warren, Ariz., for the treatment of oxidized gold-silver-lead ores. Glenn L. Allen worked out the metallurgy for this plant, employing tabling, followed by flotation concentration. The Shattuck-Denn Mining Co., successors to the Shattuck-Arizona Co., now employs straight flotation in the same mill, treating about 200 tons daily. In 1922, the San Diego mill of the American Smelting & Refining Co., in the Parral district, Chihuahua, Mexico, started operating a 600-ton mill on a mixed sulfide-oxide gold-silver-lead ore. Tables and flotation are used here, and about 200 tons of oxidized slime treated by flotation. In 1923, the Eureka Holly Mining Co. started operating a 90-ton mill at Eureka, Nev., using tables and flotation, on an oxidized lead-silver ore. In 1924, the American Smelting & Refining Co. started a 250-ton mill in northern Peru, to treat a high grade oxidized gold-silver ore with very low lead values. In 1924, the Grand Central Mining Co. started a 200-ton flotation mill on old oxidized gold-silver-lead tailings at Fairbank, Ariz. In 1926, the Compania International Minera, a subsidiary of the Union Corporation of London, started a 250-ton flotation mill on oxidized lead-silver ores, and during April of this year, the Phelps-Dodge Corp. will probably start a 250-ton mill at Warren, Ariz., on oxidized lead-silver ores, similar to those being treated in the Shattuck-Denn mill.

Jan 1, 1927

By Albert Hahn

ABOUT three years ago John Hays Hammond took over the control of the Eureka Metallurgical Co., at Salt Lake City, Utah. Funds were advanced for investigating the process invented by R. V. Smith, for concentrating oxidized lead ores. A great deal of laboratory work was done and a reagent was developed by C. M. Nokes of Salt Lake, which was found to be particularly suitable for oxidized copper ores, refractory manganese silver ores, and oxidized gold ores. After sufficient laboratory work had been performed to demonstrate the fundamental principles of these inventions, a test mill, having a capacity, of 20 tons of ore daily, was erected at Murray, Utah. In this test mill approximately 1200 tons of various types of ores have been concentrated by means of the above-mentioned process and reagents, and this large-scale work as well as laboratory work is being continued at present. Details of these mill tests are given in Table 1, and a representative group of laboratory tests are shown in Table 2. The process requires no special machinery or appara-tus. Its success depends entirely, on the method of preparing the pulp and its subsequent flotation in clean water, as outlined in the Smith patent. The reasons for the success of the Nokes special reagent are not definitely known. The outstanding feature, which seems to be of extreme importance, is that when the concentrates are examined under the microscope, each particle of mineral appears to have a particle of paraffin, attached to it. This paraffin-mineral combination seems to be particularly suitable for flotation and it follows that any coating oils readily attach themselves to the paraffin-mineral combination.

Jan 9, 1923

By P. Raffinot, M. Rey, V. Formanek, G. Sitia

CONCENTRATION of oxidized copper and lead ores by flotation has been practiced for 30 years, but flotation of oxidized zinc ores has remained unsolved until a few years ago. This problem is, however, of great importance in mining districts where large tonnages of oxidized zinc ores exist in underground mines or in dumps. Some sulphide ores also possess a degree of oxidation high enough to justify recovery of oxide zinc minerals. Various attempts have been made to float the zinc carbonate, smithsonite.

Jan 4, 1954

By Walter Morley

This paper is a record of the first of a series of tests on sulfide minerals to be made by the metallurgical department f the University of California. The purpose of the tests here recorded is to determine the action of standard oils, oil mixtures, and addition agents on the flotation of pyrites. The question of the commercial value of pyrite was not considered. Of the many factors affecting flotation, only two-the oil and the other agent used-were made variable. The flotation agents used are given in the accompanying table. PENSACOLA TAR AND TURPENTINE CO. (PENTARCO) NON-POL., SP. Dis. REF. PER No. KIND GR. POINTS INDEX ?VISC. CENT. 200 Refined wood creosote oil 0.965 105-275 1.5096 1.7 7-8 350 Crude pine wood oil 1.019 70-345 1.525 2.9 4 75 Crude wood turpentine 0.887 65-217 1.456 0.9 10-12 80 Crude pine oil 0.911 70-232 1.4894 1.1 8 750 Heavy pine tar oil 1.063 165-350 1.557 41.0 400 Wood creosote oil 1.025 190-360 1.4977 2.9

Jan 7, 1921