Search Documents

By L. B. Harris

Continuous cyclic unloading during tensile work hardening of polycrystalline zinc at room temperature enables specimens to sustain greatly increased extension. Such enhanced ductility is associated with creep-type extension, during which the cyclic component appears to promote relaxation of internal strains. It is possible to trace the transitions from tension, through enhanced cyclic extension, to fatigue and relate the observed behavior to simpler types of deformation. DISTINCTIVE deformation behavior has been shown to occur when loading includes both cyclic and unidirectional components. For aluminum and copper extended by a sequence of progressively biased strain reversals, coffin1 observed greater fracture ductility and lower flow stresses than during monotonic tension. This may be compared with the reduction in hardness obtained from conventional fatigue softening. But fatigue softening is accompanied by enhanced fatigue life,' whereas Benham3 found that fatigue life was reduced when copper continuously extended during axial load cycling. The corresponding specimen elongation, for large cyclic load amplitudes, was greater than during normal tension. Under different conditions, Bendler and wood4 found that torsional fatigue initiated extension in copper under low tensile loads previously in equilibrium with the specimen; fatigue life was again reduced. Thus there is a type of cyclic softening which is associated with reduced fatigue life and which occurs when the cyclic loading is accompanied by a unidirectional strain component. Further, the fracture ductility or extension obtained from the unidirectional component can exceed that obtained in the absence of cyclic load. Specimen extension was not initiated by axial fatigue at small load amplitudes;3 hence Benham's work distinguishes between fatigue at large and small amplitudes, the former often being linked with unidirectional deformation because of similarities in strain Structure. The initiation of tensile extension during torsional fatigue,4 however, occurred with small amplitudes. Comparable changes in behavior have been ob- served during creep. kennedy' found that combined cyclic and creep stresses on lead at 32°C increased the rate of elongation over that for simple creep, the consequence being a reduction in creep life. It was also demonstrated that small cyclic stresses applied after creep deformation initially increased recovery, but that prolonged application produced only normal fatigue hardening. It is clear that physical properties can be changed by interaction between the cyclic and unidirectional deformations, but owing to the number of different ways in which the deformations can be combined and the large number of possible variables for each combination, trends of behavior become easily obscured. One definite conclusion is that enhanced ductility or increased extension can be obtained by cyclic action, and it is this process that has been investigated for the tensile test by measurements of the extra tensile strain produced by the addition of a cyclic tensile component. EXPERIMENTAL PROCEDURE Material. Specimens were 99.99 pct Zn wire of 1.6 and 2.0 mm diam. Mean grain diameter was 0.02 mm, sufficiently small to give a ductile necked-down fracture under all loading conditions. All experiments were conducted at an average temperature of 20°C. Normal Tension. Unidirectional tensile curves at different strain rates were obtained from an In-stron testing machine, on which load-time curves were recorded autographically, using gage lengths of 5 and 10 cm. Straining was at constant cross-head velocity, and quoted strain rates are with reference to initial specimen length. Measurements of total elongation under simple tension were also made on the tensile machine that had been modified to incorporate an added fluctuating load. Combined Tension and Rapid Cyclic Load. An electromagnetic vibrator was coupled to the elastic beam of a Hounsfield ensometer- and driven sinus-oidally from a power amplifier at frequencies from 20 to 360 cps, the flexible connecting links on the tensometer being replaced by rigid fixtures to eliminate lateral vibration in the specimen. One end of the specimen was pulled by the normal extension drive of the tensometer while the other end, fixed to the elastic beam and vibrator, was subjected to rapid oscillations of load. It was thus possible to apply cyclic load to a tensile test without altering the rate of extension of the specimen

Jan 1, 1964

By Roman Šejnoha, Karel Mazanec

A pronounced tendency for delayed fracture zoas observed in the martensite structure of low-alloy steels in the as-quenched condition. Cracks of predominantly intercrystalline nature nucleated and propagated at stresses substantially lower than the short-titne tensile strength of- the steels, and were observed even in hydrogen-free speciunens. The occurrence of delayed fractures in the as-quenched condition is interpreted as a supevposition of the effect of free dislocations generated during the martensite transforlnation, and of a weakening of the prior austenite grain boundaries caused by dynamic shocks exerted on the boundaries by growing martensite plates. AN important metallurgical problem, connected with the production and use of high-strength steels, is delayed fracture in martensitic structures. Such fractures occur in quenched steels as a result of prolonged loading with external stresses far lower than the short-time tensile strength of the steel. The same effect can be produced by sufficiently high internal stresses: it is well-known that quenched structures will in some cases crack intergranularly at room temperature if not tempered quickly enough even in the absence of any externally applied stress. In Troiano's papers1,2 on delayed fractures in high-strength steels, the fundamental role of hydrogen migrating under the influence of multiaxial stress towards the nuclei of cracks was found. Fig. 1 shows the typical relationship between stress and the time to fracture found by Troiano in hydrogen-charged high-strength steels. On the other hand, Shurakov 3,4 explains the realization of delayed fractures in martensite as due to a "quasi-viscous" behavior of the austenite grain boundaries immediately after the martensitic transformation. 1) MATERIALS AND EXPERIMENTAL METHODS Two low-alloy steels of commercial purity were used for the experiments reported in this paper. Their chemical composition is shown in Table I. The heats were melted in a laboratory furnace, cast to ingots, forged to bars of 3/4 in. diameter, and annealed. Machined test pieces were heat-treated as follows: Ni-Cr-Mo steel held at 900°C for 30 min and quenched in oil; Mn-Si-Cr steel held at 900°C for 30 min and quenched in water. For the delayed-fracture tests, notched cylindrical test pieces, Fig. 2, stressed in torsion, and unnotched cylindrical tensile-test pieces, 1/4 in. diameter, were used. The specimens were normally loaded with a constant static load 45 min after quenching for the torsional tests and 10 min

Jan 1, 1965

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By Merlon C. Flemings, Theodoulos Z. Kattamis

Examination was made of the distribution of tnanganese and nickel in colutrrnar dendrites of a cast low-alloy steel; more limited work was corzducted on chromium. Corresponding "segregrction ratios" were calculnted and shown to be relntivelv insensitive to cooling rate (''segregation ratio" is defined (Is the ratio of maximum to minimum concentrations within a volume whose dimensions are the order of the dendrite-arm spacing). Isoconcentratiorl curves were determined by the electron micropvobe and by rt7etallografihic studies on specimens subjected to isothermal-transformation treatments. From construction of isoconcentration curves, morphology of columnar dendrites is descvibed as intermediate between Perfect rodlike and sheetlike morphologies. The study is extended to equiaxed dendrites and it is shown that the strcture of these dendrites is sittlilar in many respects to that of columnar dendrites. On the basis of tlze sheetlike morphology of dendrites, a simple model is pvoposed for calculation of honzogenization kinetics. Results of trzatllevlatical analysis brcsed on this utzodel are given. This analysis relates residual segregation to time at homogenization temperature; it is in agreement with experiment. Calculations are given which show that even for relatively rapidly cooled material (of 1-ine dendrite-artn spacing) treatmets at 1200°C or above are necessary to achieve slgxificant Izomogenization of elenlents other than carbon itz reasonable time (e.g., rnangclnese, nickel). Conlplete homogenization of carbon is obtnined at much lowev tenlperatures (below 870°C). IN dendritic solidification of castings and ingots, solute redistribution during freezing results in mi-crosegregation of most alloy elements. The micro-segregation is such that minimum solute concentrations occur at the center of dendrite arms and maximum concentrations occur between dendrite arms. Residual segregation after subsequent therma1 processing (homogenization) depends on maximum and minimum initial concentration, on the detailed geometry of the isoconcentration surfaces within interdendritic regions, on the diffusion coefficient of the solute, and on time of thermal processing. The objective of this work was to determine, for a low-alloy steel, maximum and minimum concentrations, and the geometry of isoconcentration surfaces, primarily in order to permit calculation of homogenization kinetics. Most of the work reported was conducted on Samples from a unidirectionally solidified, fully columnar ingot. This type of ingot is made by extracting heat during solidification from one face; techniques for accomplishing this have been discussed.' Samples were taken at several locations, up to 5.75 in. from the mold chill face; the bulk of the work was performed on samples at 5.75 in. Alloy cast was, nominally, 0.4 pct C, 1.8 pct Ni, 0.8 pct Cr, 0.7 pct Mn, 0.25 pct Mo, 0.3 pct Si, and the balance iron. Brief study was also made on samples from an ingot which solidified with equiaxed grain structure. SAMPLE PREPARATION AND ANALYSIS Samples for electron-microprobe analysis were incorporated in mounts that included pieces of electrolytic nickel, chromium, and manganese, in order to normalize the intensities of these solutes in the specimens; also, a piece of electrolytic iron was included to measure the background. All specimens were polished in the usual metallographic manner. After the microprobe traces were made, the path was revealed by etching the specimens with picral. All microprobe analyses were made by point counting, integrating for 30 sec. The distance between points was fixed from 2 to 10 p, according to the precision desired in each case, the fineness of the structure, and the concentration gradient existing in a given area. (The distance was chosen 2 to 5 p near the maximum-concentration regions and 5 to 10 p near the minimum concentration.) The "take-off" angle for the A.R.L.-Model No. 21000 microprobe employed was 52.5 deg. Samples for metallographic analysis of isoconcentration curves were prepared by austenitizing at 1540°F for 20 min, quenching to the nose of the TTT curves (1200°F), heat treating isothermally at this temperature for a given time 0, and then quenching to room temperature. Due to concentration gradients existing in a dendritic structure, no transformation will take place for a given time 0 of isothermal heat treatment in the regions where the a.lloy concentration is higher than a given limit. Thus, the dendrite appears limited by an isoconcentration curve and can be made to appear to grow by varying the time of isothermal heat treatment.

Jan 1, 1965

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,' and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By W. G. Lidman, H. J. Hamjian

' I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:' the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F') at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.' Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

By H. M. Davis, J. H. Keeler

Densities of SAE 1020 (I) and ingot iron (II) decreased with cold rolling to minima at 60 pct reduction, whereas high-purity iron (III) was unaffected. I recovered promptly with annealing; II, sluggishly and incompletely. Hydrogen occlusion of III or II was barely affected by 60 pct cold reduction, but that of I was increased a hundredfold. IT has been reported of iron that its density is decreased and its occlusive capacity for hydrogen is increased by cold work. One of the most interesting aspects of each of these properties is that the changes brought about by cold work are not necessarily eliminated by annealing and recrystallization. Yet recrystallization is generally accepted as restoring to their original condition the properties or characteristics altered by cold work. A number of investigators have reported a decrease in density with cold reduction. Two1, 2 have shown that annealing after cold reduction may not return the density to its original value. It has been suggested' that cracks or flaws in inclusions produced during cold drawing contribute to the lowering of the bulk density of the metal. Extremely high-purity copper has been reported as not exhibiting a density decrease with cold reduction. On the other hand, calculations' indicated that grain distortion by itself can produce expansion of the order of magnitude of the changes observable. Maier" showed that both the density of iron and that of copper passed through a minimum with increasing cold reduction. Although much information is available on the subject of hydrogen in steel0, 7 and it is well known that plastic deformation of a metal may increase its occlusive capacity,8-12 most of the reports pertain to charging the metal with hydrogen by cathodic deposition or with acid. Darken and Smith,'" who employed acid charging, emphasized the great influence of cold work on the occlusive capacity of iron for hydrogen and showed the inability of a prolonged high-temperature annealing treatment to restore the occlusive capacity of cold-worked steel to the value exhibited in the hot-rolled condition. It has been reportedm that an "endothermic" metal*

Jan 1, 1954

By W. J. Helfrich, R. A. Dodd

Binary aluminum solid-solution alloys containing various amounts of silver, magnesium, and zinc were prepared by careful directional solidification, and the hydrostatic and X-ray densities were compared. With the exception of the Al(Ag) alloys, the X-ray densities were consistently greater than the hydrostatic measurements, in agreement with earlier observations by Ellwood. In contrast to Ell-wood's interpretation in terms of vacant lattice sites associated with Brillouin zone effects, a tentative explanation based on the existence of solidification microshrinkage was favored. This hypothesis was confirmed by an examination of Al(Zn) alloys prepared by vapor diffusion of zinc into aluminum. The hydrostatic and X-ray densities were now in very close agreement, and it was concluded that the filling of Brillouin zones in aluminum solid-solution alloys does not necessarily result in the formation of defect structures containing an excess of vacant lattice sites. ThE existence of defect structures of the vacancy type in alloys in which the excess vacancies have an electronic rather than a thermal or mechanical, and so forth, origin is well recognized. Examples of incomplete lattices of this type are to be found in the Ni-Al,1-3 Fe-Ni-A1,4 c~-Ni-Al,5 Fe-Cu-Al,= and Co-A17 systems. These defect structures are of a special kind in that the intermediate phases possess an ordered atomic arrangement or superlattice, and in some instances the vacancy concentration may be unusually large, e.g., at 45.25 at. pet Ni in NiA1, approximately 8.8 pet of the lattice sites are unoccupied. Ellwood8-10 has reported similar defect structures in the aluminum solid solution alloys of the Al-Zn and A1-Mg systems and in alloys of the Au-Ni system." In Al(Zn) the (apparent) vacancy concentration rose, somewhat irregularly, to a maximum of about 2 pet vacant sites at 25 at. pet Zn, while in Al(Mg) the (apparent) vacancy concentration increased continuously to 1.7 pet at 15 at. pet Mg. An explanation in terms of Brillouin zone overlap was attempted, although Pearson12 has pointed out the difficulty of reconciling the observations with zone theory. However, the possibility of the effect being caused by the Fermi surface just touching a plane of energy discontinuity inside a prominent Brillouin zone has, in general, been accepted. In fact, Massal-ski13 has interpreted Ellwood's8 observations as confirmation of Leigh's14 theoretically predicted zone overlap occurring at approximately 2.67 electrons per atom. Unfortunately, Massalski was apparently unaware that Ellwood9 had revised his earlier results considerably, and the revised data did not confirm Leigh's analysis. Ellwood's clata were reexamined by the present authors who noted a possible correlation between the percentage defects as a function of alloy composition and the temperature interval of solidification measured from the respective equilibrium diagrams. This suggested an explanation in terms of shrinkage porosity rather than vacant lattice sites, and pointed to the desirability of reexamining appropriate alloy systems using: both Ellwood's method of specimen preparation (casting followed by wrought fabrication) and alternativ'e methods, i.e., diffusion, which might be expected to minimize, or even completely obviate, microporosity. ALLOY PREPARATION 1) Cast Allolys and Aluminum Single Crystals. Al(Ag), Al(Mg;l, and Al(Zn) alloys of various compositions up to 20 at. pet silver, 13.5 at. pet mg, and 30 at. pet Zn were prepared by melting under helium and casting into graphite molds. In the first two systems, the maximum alloying addition was quite close to the limit of solid solubility, but the possibility of transformation to a' during quenching somewhat restricted the suitable Al(Zn) composition range. The alloys were prepared from high-purity aluminum, a lot analysis showing 0.002 wt pet Cu, 0.002 wt pet Fe, and 99.996 wt pet A1 by difference. The silver, magnesium, and zinc were of 99.99+, 99.98+, and 99.998 wt pet respectively. Each composition was analyzed chemically. The as-cast ingots measured 7/16 in. diam and 5 in. length. One in. was removed from the top of the ingot, and the bottom 3 in. was machined to 0.275 in. diam; a point was also machined on the smaller diameter end. The remainder of the original ingot served as a top riser during subsequent remelting and controlled solidification. The machined ingots were now remelted using a Bridgman soft-mold technique to ensure directional solidification and, therefore, a minimum of micro-shrinkage. Alumina powder was used as mold material contained in an alundum thimble, and this crucible was placed in a helium-filled Vycor tube. The assembly was lowered through a suitable temperature gradient at approximately 0.5 in. min-l, and the risered portion of the casting was subsequently removed by sawing.

Jan 1, 1962

By L. R. Testardi, J. R. Wiese

OBSERVATIONS have been made that the substitution of antimony for bismuth in Bi2Te3 leads to anomalies in some of the electrical and magnetic properties of the Bi2Te3-5S2TeS alloy system at the composition ratios 2 Bi2Te3 : 1 Sb2Tes and 1 Bi2Te3 : 2 Sb2Te3. Airapetiants and Efimova1 have reported the peaking of the nondegenerate hole mobilities, at these compositions for sintered materials and ascribe the peaking to the formation of ordered alloys. From a study of these materials produced by the Bridgeman

Jan 1, 1962

By Harry W. Antes

The density changes that occurred on annealing cold-worked poly crystalline molybdenum, over the temperature range of 870" to 1630 SC, were determined. Increases in density were observed for recovery and the beginning of recrystallization. An initial decrease in density was observed during re-crystallization. A second decrease in density was observed after recrystallization was completed, as the microstructure changed from columnar grains to equiaxed gvains Both decreases in density were associated with an increase in gain boundary area to volume ratio. The second decrease in density was observed in the annealing range that immediately precedes secondary recrystallization as reported in the literature VARIOUS techniques have been used to identify the recovery, recrystallization, and grain growth processes that occur when cold-worked metals are annealed. As early as 1928 work was conducted that indicated measurable density changes occur when cold-worked single crystals of brass are annealed.' More recently, work by Murphy exhibited a corre- lation of density with microstructural changes observed on annealing cold-worked polycrystalline a brass.2 Other investigators have performed similar work on a brass and copper.324 In reviewing the literature, it was apparent that density work had been limited to fcc materials. Therefore, it was the purpose of this investigation to determine the density changes that accompany annealing the cold-worked bcc material, molybdenum. Two degrees of cold work, 30 and 90 pct reduction of cross-sectional area by rolling, were selected for this study. EXPERIMENTAL PROCEDURE High-purity vacuum arc-cast molybdenum was used in this study, the principal impurity being carbon in the amount of 80 ppm. The final rolling reductions were made at 1200°C in grooved rolls to provide 5/8-in.-diam rod. Density specimens 0.500 in. diam by 1.5 in. long were machined from the bar stock. The specimens were ground to the final dimensions to provide a smooth surface. Density measurements were made using a hydrostatic technique similar to that used by ~urphy.' This type of equipment permitted weighing in liquid immediately after the air weighing. During each weighing the temperature of the air and liquid was controlled to within 0.0l°C. This was accomplished by sealing the analytical balance in an air-tight brass chamber and surrounding it by an insulated wooden case. Preheated air was circulated in the air space between the brass chamber and wooden case by means of a blower. The temperature of the

Jan 1, 1964

By R. W. Heckel

A method is described whereby the relationship of both the "at-pressure" powder compact density and the "zero-pressure" compact density to the applied pressure may be obtained from continuous measurements of punch movement during a single compaction operation. The rate of density increase with applied pressure for the metal powders is found to be proportional to the volume fraction of pores for pressures exceeding a lower limit which varies from 15,000 to 30,000 psi, depending on the powder. 1 HE compaction of powdered materials is carried out primarily to increase the density of the material. If the ultimate goal of the over-all process is the attainment of minimum porosity, compaction is responsible for most of the densification. For example, loose powdered metals have porosities of about 65 to 75 pct. Axial loading in a die or hydrostatic pressure may effectively reduce the porosity of most powders to 20 pct or lower with pressures of 50,000 psi and greater. The relationship between the density of a powder compact and the pressure needed to achieve that density is most commonly obtained by pressing several compacts, each at a different pressure. Measurement of the densities of the individual compacts when they are removed from the die then provides the density-pressure relationship. However, this method suffers from several disadvantages. Because a large number of compacts and pressing operations are required, it is inherently slow. Furthermore, since density measurements are made after the specimens are removed from the die, data obtained refer only to pressures greater than those necessary to form a coherent compact. The third disadvantage is the inability of this method to provide information about the compact density at the applied pressure in the die. Because the determination of density-pressure relationships has been a slow, tedious process, investigators have sought to express the compaction behavior of powders by other means. The general terms "comparability" and L'compressibility" have been used to rank powders qualitatively according to their compaction characteristics. To restore a quantitative nature to the subject and to prevent confusion, Schwarzkopf1 has proposed that compac-tibility be defined as the minimum pressure needed to produce a given green strength, while compressibility should be used to indicate the extent to which the density of a powder is increased by a given pressure. Probably the most widely used of the compaction parameters is the "compression ratio,'' which is generally defined as the ratio of the compact density obtained by pressing at a given pressure to the apparent density of the loose powder.2 However, the description of the compaction behavior of a powder by these parameters provides only limited information about the process because of their applicability to just one specific condition such as a given green strength or a given pressure. The method of obtaining density-pressure relationships which will be described in the present paper was designed to eliminate the shortcomings of the previous techniques while maintaining equivalent accuracy and precision. EXPERIMENTAL TECHNIQUES The general principle employed makes use of the fact that the linear movement of the punch during a

Jan 1, 1962

By R. A. Vandermeer

It is usually assumed that the rate-determining step in the migration of a grain boundary involves the thermally activated transfer of single atoms across the interface. Chemical reaction rate theory then gives a migration rate which is proportional to the driving force when this is small compared to kT.1 In their recrystallization studies on aluminum, Gordon and vandermeer2 obtained data which was capable of providing the first experimental test of this proportionality. They correlated stored energy (driving force) release measurements determined calorimetrically with fraction recrystal-lized kinetic (growth rate) data acquired metallo-graphically at a temperature where a significant amount of recovery takes place concurrently with recrystallization. Within experimental error, the results of Gordon and Vandermeer confirmed experimentally, at least over a limited range, the linear dependence of boundary migration (growth) rate on driving force in accordance with theory. In obtaining these results, however, an incorrect, implicit assumption was made in relating the average instantaneous growth rate of the recrystallized grains to the measured fraction recrystallized kinetic data. The purpose of this present note is to point out and correct this assumption. An alternate approach, whereby a more proper average growth rate can be calculated from the recrystallization kinetic data, is presented. The earlier data, reevaluated in terms of this new approach, show the same general trend as before so that the original conclusion of Gordon and vandermeer2 is still valid. As was shown in a detailed study3 of the geometrical features of recrystallization in aluminum, the colonies of recrystallized grains can be regarded as uniform cylinders embedded in a three-dimensional matrix, the number of such colonies being constant. Thus during the early stages of recrystallization the volume fraction recrystallized, Xv, can be written as Xv=ynvlr2 [l] where y is a shape factor and i and r are defined as the average length and radius of a recrystallized colony and are spatial averages over the specimen. -nv, is the number of such colonies in a unit of volume. The erroneous assumption made in the earlier paper2 was that r in Eq. [I] could be replaced by

Jan 1, 1965

By H. P. Stuwe

It is investigated whether a model of sphere packing permits the computation of the lattice parameters and their variation with concentration in various a phases; it does, except in phases containing silicon. Several observations indicate that a particular role is played by the "E-atoms" in the lattice. THE phase is formed by many alloys of the transition elements.'-' Its structure has been described by Bergman and Shoemaker,5,8 Dickins, Douglas, and Taylor,7 and Kasper, Decker, and elanger.' There are five kinds of crystallographically equivalent positions for the 30 atoms in the unit cell which have been designated by these authors I, 11, 111, IV, and V or, in the same sequence, A, B, C,D, and E, as shown in Fig, 1. For the purposes of the present paper two elements of the lattice will be discussed separately: The lattice planes perpendicular to the c-axis which are made up by the atoms A, B, C, and D and which determine the a-parameter; and the close-packed "vertical rows" of E-atoms which determine the c-parameter. asper,9 and Frank and kasper10 described the a phase and other complex structures as sphere packings. In these papers particular attention is paid to the coordination polyhedra. Lattice positions with an equal number of nearest neighbors are considered equivalent regardless of their crystallo-graphic description. This seems to work very well for the explanation of ordering phenomena in the a phase as far as information on this is available." If the description of the phase as a sphere packing is valid it should be possible to draw two further conclusions: 1) It should be possible to calculate the lattice parameters from the atomic radii of the components, and 2) It should be possible to predict the variation of the lattice parameters with concentration within one phase field. Both points are discussed in this paper. PROCEDURE Measurements of lattice constants were done with a symmetrical back-reflection X-ray camera. With Cr-radiation, about a dozen a1 lines could be observed with most samples. From the (550/710)- and 720-lines the a-value was computed. With this value the c-parameter was calculated from the (333)- and (413)-lines. Finally, the position of all the other lines was computed from the lattice parameters thus obtained. In this way the validity of the indexing could be checked and, at the same time, this proce- dure gave an estimate of the accuracy of the lattice parameters. A correction was made for film shrinkage. The atomic radii used in the computations are the Goldschmidt radii for coordination number 12. Actually, some of the atoms have a coordination number of 14 or 15, but the error thereby introduced is small. * For the computation of lattice constants from the atomic radii an "average atomic radius" of all components was used, i.e., complete disorder was assumed. Although this seems to be true for some systems like OS-Cr,4 it is not true in others.11,13,14 The ordering model, however, which has been suggested by Kasper on the basis of extensive research lets both kinds of atoms contribute to both the ''vertical rows" and the lattice planes perpendicular to them, so that even with ordering of this kind the assumption of complete disorder cannot introduce a very serious error in calculating lattice parameters. RESULTS Bergman and shoemaker6 gave a table of the interatomic distances in the Fe-Cr phase. If we disre-

Jan 1, 1960

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

PRACTICAL designs for good "home made" molybdenum furnaces are hard to find in the literature. The one described briefly below left something to be desired but was good enough to operate as a rather long (30 in.) two-zone furnace for periods of over 2 months at temperature (1400° to 1600°C) without shutdown. The principal problem in our application was to establish a temperature profile with two distinct constant-temperature zones and no dip between the zones. This and other problems mentioned below would not arise, however, if both zones were operated at the same temperature and if a shorter furnace were acceptable. Since molybdenum windings oxidize very rapidly when heated in air, impervious refractory tubes were used for both the furnace core and the outer jacket tube shown in the accompanying figures. A protective atmosphere of forming gas (10 pct H2, 90 pct N2) was continuously passed through the gas-tight annular volume between the core and outer jacket. The water-cooled copper ends shown in Figs. 1 to 3 sealed the ends of the tubes. Annealed molybdenum wire (40 mil) was wound on the recrys-tallized alumina core (35.5 mm OD by 28.5 mm ID by 30 in.) at a spacing of 0.36 in. The spacing was reduced to 0.29 in. close to the ends to partially compensate for end heat losses. Fig. 2 shows two molybdenum-ground lead taps off the center of the winding to produce the two independect temperature zones. The ground lead was insulated with 1/4-in. alumina tubing and connected to the grounded copper end by passing the wires through the gas port tube and crimping each wire into notches cut at the mouth. To prevent sagging of the core at high temperatures, refractory "troughs" were cut from alumina and mullite tubing to cradle the core. The support "troughs" which were 6 in. long and located about 5 in. from each end of the annular volume also served as radiation shields. In view of the different expansion coefficients and operating temperatures of the core and outer jacket (3.5 in. OD by 3 in. ID by 30 in.), the ends of the tubes were smoothed and squared to produce good sealing surfaces, and the core was ground 1/32 in. shorter than the outer tube. The power terminals were passed through their respective conductor ports which were internally lined with alumina tubing and sealed with Armstrong adhesive A-6 leaving about 1 in. of protruding lead wire for external connections. (Adhesive A-6 is a two-component system consisting of an epoxy-type resin with a mineral fibrous filler and an amine catalyst.) Figs. 1 and 3 show the entire assembly of concentric refractory tubes, copper ends, and sealing o rings, held together with two brass flanges and 3/8-in. bolts with heavy springs for dimensional flexibility. The furnace shell (19 by 19 by 30 in.) consisted of a steel frame with sheets of transite forming a box. The copper ends protruded through two 3.75-in. circular holes cut at the center of each transite square end. Thermal insulation next to the transite exterior was effected by K-23 B&W bricks alld in a central volume of approximately 9 by 9 by 30 in. a row of K-30 bricks was lined up to support the hot assembly. The rest of the volume around the outer

Jan 1, 1965

By L. J. Buteau, R. E. Reed-Hill, W. A. Slippy

In a zirconium {1121} twins tend to have coherelzt boundaries and thus do not usually taper to a point when they intersect a grain boundary. Under the proper conditions, a (1121) twin may deform a boundary in such a manner as to clearly rcveal the twinning shear. Measurements of these grain-bounrlary rotatzons yield a value of 0.63 for the (1151) twinning shear. The magnitude of the observed shear and its shear sense are in excellent agreement with the assumption that the second undis-torted plme (K2) for this form of twinning is the basal plane (0002). The present value of the tzvinninz shear, which is approximately three limes larger than Rapperport&apos;s value? is in excellent agreement with reported results of Sokuskii and Prolsenko.5 RECENTLY westlake&apos; reported a study of the twinning modes of zirconium based on ~ap~er~ort&apos;s2 values for the twinning elements. He observed that two of the modes, (1012) and {1122), can be explained by relatively simple dislocation models. A workable model for (1121) twinning, however, proved to be very complex and questionable. Because Rapperport&apos;s second undistorted plane, (K2), for (1121) twinning has large indices, {ll2l6), it is possible that the difficulty in defining a model for (1121) twinning lies in an incorrect value for K2. A measurement of this twinning element has therefore been made, using a method based on observations of the shear displacement of grain boundaries at positions where they are intersected by (1121) twins. EXPERIMENTAL PROCEDURES The zirconium specimens were deformed in tension on an Instron machine either at the temperature of liquid nitrogen (77ºK), or prestrained at liquid nitrogen temperature and then further deformed at room temperature. Straining at 77°K was employed in order to nucleate (1 121) twins in large numbers, since simple ropm-temperature tensile deformation favors (1012) twinning. Specimens were machined from 1/2-in.-thick plate. The material was arc-melted sponge zirconium annealed to an ASTM grain size 4 and containing, in parts per million, 380 Fe, 880 0, <40 Hf, 32 N, and < 5 H. The specimen gage length and diameter were 1.25 and 0.130 in., respectively. To insure a gage section initially free of twins, the last 60 thousandths of the specimen diameter was removed by acid machining.

Jan 1, 1963

By M. E. Shank, J. Wulff

At the present time, the designer of dies for metal powder pressing is handicapped by relative ignorance of stress distribution and frictional effects at the interior surface of the die. Unckell was the first to develop a method for the study of wall friction. He used three Brinell balls on which the die rested during pressing. The total frictional wall force was determined by the size of impression these balls left on a soft metal plate. Since the method does not give radial pressures, or distribution of such pressures, coefficients of friction could not be determined. Although Unckel measured density distribution, he was not able to determine radial or shear stresses. Shaler2 has proposed theoretical expressions for the stress and density distribution within cylindrical compacts during pressing, in accordance with the experimental results of Kamm, Steinberg, and Wulff.3 By application of Siebel&apos;s method,4 Kamm et a13 plotted stress trajectories for two compacts. From the stress trajectories they calculated coefficients of friction from point to point along the die wall. As pointed out by Shaler in the discussion of Ref. 3, these values are based on progressive point-to-point calculations on finite size grid squares across the compact. In the region of the die wall such calculated values may therefore have considerable cumulative error. The purpose of the present paper is to develop an experimental method by which the nonhydrostatic pressures and shears acting on the interior wall of a cylindrical die can be measured. Such measurements can then he correlated with existing data to aid in the explanation of the pressing process. The method used is based on the elastic: properties of the thick-walled tube used as the die. The principle of super-position of force systems on an elastic body is assumed to hold. Electric strain gauges were mounted in adjacent positions on the exterior die wall in order to get an exact measurement of the variation of tangential strain over the length of the die during pressing. While in this paper, measurements in terms of only tangential strains are considered, it is well to note that similar calculations may be set up for axial strains. The latter are not preferred, since they tend to be smaller than the tangential strains and therefore permit less sensitive measurements. Discussion in this work is restricted to compacts pressed from both ends, since the elastic deformation of the die is then more amenable to analysis. Before choosing the electric strain gauge method, a more direct line of attack was considered and discarded. The discarded idea was the insertion of a pressure gauge through a hole in the die wall.* The gauge would have been in the form of a small piston. If pressure were exerted against such a gauge, it would move outward along a radius of the die. One disadvantage of the scheme is its inability to measure shears along the die wall. Another more serious disadvantage is the disturbance caused by the device itself. It would serve to change the forces it was designed to measure. No matter how small the movement of the gauge, when pressure is applied a discontinuity would exist in the wall surface at that point. Due to the stress concentration caused by the hole, abnormal deflections of the die wall would occur around the gauge. During pressing, powder would be forced into the resulting depression. The depression would then become larger with increasing compacting pressure. Powder, not being a fluid, is capable of supporting shear. The ease with which it would flow into the die wall depression to further move the piston is an indication, not of the radial pressure at that point, but of the state of shear retarding the movement. Thus the "pressure" gauge is really a criterion of flowability, and of the capability of the powder to support shear. For these reasons, it was decided that the electric strain method, herein employed, was more reliable, if more indirect. The gauges and lead wires, mounted on the external die wall do not in any way affect the behavior of the metal powder or the die during pressing. Theory of the Method THE EFFECT OF RADIAL PRESSURE ON THE DIE WALL Effect of a Single Small Band of Hydrostatic Pressure Consider a die which is a thick-walled cylinder of outer radius R. and inner radius Ri. If over a small finite length L there is a normal pressure P, a tangential strain distribution at the outer wall results. This is shown schematically in Fig 1. The exact shape of the curve may he predicted by an extension of the theory of a semi-infinite beam on an elastic foundation.6 This

Jan 1, 1950

By M. E. Shank, J. Wulff

In view of the current interest in magnetic materials having rectangular hysteresis loops, as for example those obtained with the grain oriented 50 nickel 50 iron alloys,t we wish to call attention again to the results obtainable with the perminvar (Co-Ni-Fe) alloys heat treated in a magnetic field. Data taken from direct current measurements made prior to and during World War II give the typical values shown below for two of the perrninvar alloys. Fig 1 and 2 show- the hysteresis loops for these samples. The first sample above consisted of small rings punched from 0.014 in. sheet stock. These rings were heat treated at 1000°C for one hour in a hydrogen atmosphere and then cooled with the furnace to 750°C at which point they were subjected to a magnetic field of 15 oersteds maintained during cooling to room telmperature. The molybdenum perminvar sample consisted of a spirally wound core of 0.001 in. tape. The heat treatment was the same except that box annealing methods were used and no hydrogen atmosphere was employed. Even better properties might be expected using hydrogen. The heat treating temperatures and cooling rates are not critical. Rectangular hysteresis loops produced in other perminvar alloys by heat treatment in a magnetic field were described earlier.&apos;,? Properties similar to those described above are realized in perminvars manufactured by conventional methods. Drastic cold working which in practice limits the final thickness and is gen- erally expensive may thus be avoided. This information may be of interest to those concerned with magnetic alloys and the development of contact rectifiers, magnetic amplifiers and so on.

Jan 1, 1950

By R. Steinitz, L. Seigle, R. Resnick

THE rates of growth of the carbide phases MC and M2C in the Ta-C and Cb-C systems have been measured at various temperatures and the results used to estimate the rate of carbon diffusion within the inter metallic phases. Sheets of high-purity tantalum (50 ppm Cb, <25 ppm Ti, 10 ppm Fe, 5 ppm Cr, <50 ppm Mo, W, and all other metals, 15-75 ppm O2, 10-30 ppm N2, and 10-30 ppm C) approximately 1/4 by 1/2 by 0.020 in. were heated to temperatures between 1800" and 2700°C in a carbon resistor furnace under an atmosphere of argon plus sufficient methane to maintain an excess of carbon at the sample surface. The thicknesses of the carbide layers, illustrated in Fig. 1, were measured with a filar micrometer and plotted logarithmically as a function of time. Fig. 2 is a typical plot for the TaC phase. The points may be represented within experimental error by lines with slope equal to 1/2; therefore the growth of the layers may be described by the usual expression X = kt1/2, where X is the layer thickness, t is the time, and k is a temperature-dependent constant. From these data and compositions at the phase boundaries, it is possible to estimate values for the diffusion coefficients of carbon in each phase, assuming that layer growth occurs by carbon diffusion alone, and that the dif-fusivity is not a function of composition within each

Jan 1, 1965

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,&apos; however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500&apos; with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962