Search Documents

By W. C. Hellyer, R. A. Campbell

In single-stage autogenous grinding, the buildup of a critical size fraction in the media can be corrected by removing this material through pebble ports, crushing it below the critical size range, and recycling the crusher product back to the mill. The rate at which the critical sire fraction is crushed affects the size distribution of the grinding media and this in turn affects the sire distribution of the grate discharge. This provides a means for controlling the grind produced by a single-stage autogenous grinding unit. The pilot-plant investigations on a very hard copper ore were carried out at the facilities of the Institute of Mineral Research, Michigan Technological University. In an autogenous grinding circuit in which feed at approximately 9 in. top size is reduced to a size suitable for subsequent processing, the build-up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge."' The buildup of a critical size fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large-diameter steel balls to the grinding charge. This has certain disadvantages, such as 1) an increase in mill liner wear, 2) wear on the steel balls, and 3) some loss in flexibility in grinding circuit opera-tions resulting from difficulties in removing the steel balls by means other than by grinding out. A number of investigators' have suggested the use of a small crusher as an alternative to the use of large steel balls for control of a critical size fraction. With this technique the critical size fraction is removed from the mill continuously through suitable-sized pebble ports, crushed below the critical size range, and returned to the mill. An external crusher would cause no increase in mill liner wear, the wear on the crusher would be less expensive than the wear on the steel balls, and the flexibility of the grinding circuit operations would be enhanced since the crusher can be cut into and out of the circuit at will. This paper describes an autogenous grinding pilot plant investigation on a very hard copper ore, which led to the selection of an autogenous grinding flowsheet incorporating a crusher in the circuit as the preferred method for grinding this ore. Further development of the technique demonstrated that the crusher could be employed to control the product produced by an autogenous grinding unit. Description of Pilot Plant These investigations were carried out at the pilot-plant facilities of the Institute of Mineral Research, Michigan Technological University, Houghton, Mich. The autogenous grinding unit was a 6-ft-diam by 2-ft-long Hardinge Cascade mill with %-in. slotted steel grates. Pebble ports cut into the grates allowed passage of pebbles having a top size of approximately 21/2 in. The grate and pebble-port discharge material passed over a 3/16-in, trommel screen with the trommel under -size being pumped to the classification device. DSM screens were employed for classification in the early investigations, but were replaced later by a small Dorr rake classifier. The trommel oversize material returned to the mill via scissor conveyors. When the crusher was incorporated into the circuit, the trommel oversize material passed to a double-deck vibrating screen fitted with 2-in. and 3/4-in. square mesh screen cloths. The $ 2-in. and the —2 +3/4-in. size fractions were combined and crushed to a nominal 1 in. in a 4 x 6-in. jaw crusher. The crusher discharge and the —3/4-in. screen undersize returned to the mill. In the final investigation, a flap gate fitted to the top deck of the screen directed the — 21/2 +2-in. size fraction to the crusher or back to the grinding mill. The flap gate operated manually on a 15-min cycle, with this material being crushed for so many minutes out of each cycle. This was found to be a more reliable method of controlling the amount of — 21/2 +2-in. material crushed than attempting to make a split of a small weight of material on a continuous basis. Operational Techniques: Each sample was sized into three fractions and the Cascade mill feed was reconstituted from these size fractions in the proportions existing in the original sample. Sufficient feed for 15 min operation was weighed out and fed by hand over a 15-min period. The gross mill power draft was recorded every 15 min, corrected for tare power and drive efficiency, and reported as net kilowatt-hours per ton. A recording kilo-watt-hour meter provided a continuous visual record of the power drawn by the mill. Pulp densities of the trommel undersize and the classifier overflow (or DSM undersize) were taken every 15 min. The classifier overflow was sampled automatically. Timed samples of the classifier sands were taken every 15 or 30 min, weighed, and returned to the circuit. After correcting for moisture content, the weights were converted into percent circulating load. Timed samples of the +2 in., the —2 + 3/4-in., —3/4-in. screen fractions, and the crusher discharge, were

Jan 1, 1971

By H. A. Hoffman

Competition from an all-flotation plant, with demonstrated economies and efficiencies, plus a change in smelting contract and introduction of improved cyclones lead to conversion from gravity-flotation. Detailed descriptions are given of equipment installed and procedures used at St. Joseph Lead's Federal mill. Future plans include further quality control by instrumentation in all aspects of the mill operation. Also planned are improvements in materials handling systems. Competitive conditions will continue to dictate improvements and changes in the mill flowsheet. The advent of all-flotation mills in the Lead Belt was introduced by the Indian Creek mill in late 1953. This modern and efficient plant then became a pattern for the other mills in this area to re-evaluate their circuits in an effort to develop flowsheets that would improve operating conditions and metallurgy. The Indian Creek mill demonstrated that all-flotation would require considerably less operating and maintenance labor than the combination of tabling and flotation that was common in the Lead Belt at that time. Two significant changes occurred in recent years to allow all-flotation to be seriously considered in other Lead Belt mills. One was a change in the smelting contract which did not require gravity concentrate. Another was the development of cyclones which provided classification of the flotation feed in a very small space. Since the Federal mill was the largest concentrating plant in the Lead Belt it was felt that the greatest savings could be made by investigating the all-flotation possibilities at this mill. Interest was stimulated by the milling and ore dressing Depts. to determine if this mill would be converted without undue cost, provided the metallurgy could be improved. Accordingly, laboratory tests were initiated to learn what metallurgical benefit could be derived. Numerous tests were run which indicated that grinding to all-flotation would improve the tailing by as much as 0.02 pct Pb. This was quite significant when multiplied by the tonnage of ore treated. Projecting the added cost of power for extra grinding and flotation, and the additional flotation reagents required, plus additional new equipment that would have to be purchased, it would still add up to a considerable saving. The all-flotation mill would reduce man power by some 30 pct, and make a metallurgical improvement. Operating costs could be reduced bv 2$ per ton. The metallurgical improvement would amount to 4$ per ton, for a total of 6$ per ton of ore milled. An estimate of the cost of the conversion was set at $250,000. With the savings as estimated this could be paid off in about two years. On paper it therefore seemed attractive enough to justify a mill test. MILL TESTING One section of the Federal mill was made available for use as a separate test circuit. Cyclones and density controllers were borrowed from the Viburnum and Indian Creek mills. Denver flotation cells were obtained from the Desloge mill that was then shut down. Two 10-cell groups of Fagergren flotation machines, consisting of eight roughers and two cleaners in each bank, were segregated from the remainder of the plant. The 9x12-ft rod mill was continued as a primary grinding mill. The two 6%x12-ft mills on this section were converted from rods to balls, and the speed increased to 22.0 rpm. Cyclones were installed to close the circuit of these ball mills. The ground pulp from each of the ball mills was fed separately to its own bank of flotation cells so that two completely separated test circuits could be run in parallel. This test circuit operated on a three-shift basis from Dec. 22, 1959 to Mar. 21, 1960. The first few weeks were occupied in developing conditions for proper metallurgy and trouble-free operations. Results were rather erratic but as the ore dressing laboratory and the mill operators became more familiar with conditions they were able to obtain expected results, which could be duplicated day after day. The last five weeks of testing indicated the best results and are tabulated in Table I. During the first two weeks a Denver unit cell was used on No. 1 flotation circuit. Even though it recovered almost one half of

Jan 1, 1962

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

The paper describes an improved process for the recovery, purification, and concentration of copper values from acidic dump leach liquors. The process employs a new liquid ion exchange material (LIX® 64 reagent) capable of separating copper values from iron and other impurities common to dump leach liquors in the typical pH range of 1.4-3.0. Properties and performance of the reagent are discussed. Design scale-up information for both pilot plants and commercial installations, including preliminary economics, are presented. Economic considerations include the production of electrolytic copper from the purified copper aqueous concentrate. INTRODUCTION Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that a wide selection of chemical reagents to efficiently and economically separate many metals in solution under a wide range of conditions would be commercially available. Several years ago, General Mills began a basic research and development program to determine if it were possible to develop a reagent to extract economically metallic ion from existing process streams. Progress toward reaching this objective was reported in late 1963, when development of quantities of LIX -63 reagent, a highly selective reagent for the extraction of copper, was introduced. The properties of this reagent are described in a previous paper.' The development work with this reagent indicated that perhaps the largest potential application for a copper extractant, the treatment of acidic dump leach liquors, would not be economically possible with LIX-63 because of limitations of the reagent to extract copper below a pH of 3.0. The relatively small pH adjustment required with LIX-63 would result in a significant processing cost and the undesirable precipitation of ferric hydroxide from the liquor. This pointed to the need for another copper extractant which would extract copper from dump leach liquors without pH adjustment. General Mills was successful in synthesizing a molecule which does not have the pH limitation of the LIX-63, yet possesses the selectivity-solubility properties required of a metallic extractant. The resulting LIX-64 reagent broadens the pH range from which copper can be effectively extracted and separated from other metallic impurities. Of special significance is the fact that the reagent, LIX-64 was developed by combining the technical requirements of a specific problem in hydro-metallurgy with theoretical organic and physical chemical principles.

Jan 1, 1967

By R. T. Hukki

This paper presents a series of equations for mechanical ball wear, relating parameters of ball size, mill speed, and mill diameter. The fundamental equation, Eq. 12, presented here is introduced to correlate these basic parameters and thus define and clarify the concept of ball wear. This equation is offered as a general rule, which may be modified to apply to individual problems of grinding. BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that 1 n = 0.7663 np----=— rpm [1] vD P = c, np D kw [2] T=c²(np)n De tph [3] In these equations n — actual mill speed, rpm np = calculated percentage critical speed D = ID of mill in feet P = power required to operate a mill, kw T = capacity of a mill, tph C¹ and c² - appropriate constants in = exponent of numerical value of 1 5 m 1.5 Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate). It is generally accepted, although not sharply defined, that ball wear in mills running at low (cascading) speeds is a function of the ball surface available. Accordingly, the wear of a single ball may be considered to be a homogeneous, linear function of its surface and of the distance traveled. Thus dw = f¹(d2) . f2(ds) [4] where dw is the wear of a single ball in time dt, d the diameter of the average ball in ball charge, and ds the distance traveled by the ball in time dt. Indicating that ds - a D n dt, the wear of the average ball in time dt becomes dw = f¹(d2) . f2(Dn dt) 1 --- f¹ (d1) f² (D c3 np-----— dt) \/D = c,d² n, D dt The rate of wear of the average ball is given by dw/dt. dw/dt = c, d² np D lb per hr [5] The weight of the ball charge per unit of mill length is a function of D The number of balls of size d in the ball charge is = f³(D2)/f4(d³). The rate of wear of the total ball charge equals the number of balls times rate of wear of the average ball. Thus rate of total ball wear = — . (dw/dt) w. c, . (l/d) . n,, D lb per hr [6] which is the equation of ball wear in low speed mills. In a mill running at a low speed, grinding is the result of rubbing action within the ball mass and between the ball mass and mill liners. When the speed of the mill is gradually increased toward the critical, the impacting effect of freely falling balls becomes increasingly prominent in comparison with the rubbing action. Reduction of ore takes place partly by rubbing, partly by impact. The share of the freely falling balls in the reduction of ore reaches its practical maximum at a speed somewhat less than the critical; at that speed grinding by rubbing has decreased to a low value. It may be reasonable to think that size reduction by freely falling balls should reach its theoretical maximum at the critical speed, if the fall of the balls were not hindered by the shell of the mill beyond the top point; grinding by rubbing would cease at the critical speed. As a first approximation, wear of freely falling balls may be considered to be a homogeneous, linear function of the force at which they strike pieces of rock and other balls at the toe of the ball charge. The force equals mass times acceleration. The mass of a ball is a function of d3 and its acceleration is a function of the peripheral speed of the mill. The wear of a single ball of size d representing the average ball in a ball charge will therefore be w¹ = f3(F) = f (d3) f7 (v). [7] Indicating that v = D n, and n = c³ np 1/vD, Eq. 7 becomes W1 = cn d3 np Do.5 lb per hr. [8] Total wear of the ball charge equals number of balls times the wear of the average ball. Number of

Jan 1, 1955

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylam-monium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x105 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values.2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x105 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle

Jan 1, 1958

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By E. J. Roberts

Hydrometallurgical operations and many processes in the chemical industry require the separation of dissolved material from solids. One of the decisions which has to be made in designing a plant for such an operation is how this separation shall be accomplished. It is the purpose of this paper to set forth the general principles involved in such separations in order that the optimum flowsheet and equipment may be selected. Countercurrent Decantation with thickeners, or C.C.D. as it is generally known, is, of course, only one way of separating dissolved material from undis-solved. Other unit operations such as Countercurrent Filtration (C.C.F.) and Countercurrent Classification (C.C.C.) are widely used. The same principles may also be applied to centrifugally assisted decantation, as with nozzle or solid bowl type centrifugals, and to separations using screens, either gravity or centrifugal type. Another form of countercurrent washing applicable to granular materials is practiced in continuous ion exchange operations. All of these operations depend on two basic principles, or combinations of these principles. In C.C.D. type operations the solids are concentrated into the smallest possible volume of liquor in each step and the resulting pulp then mixed with a more dilute liquor and recon cen trated, the liquors separated from the more dilute stages being advanced to dilute the more concentrated liquor in a previous solids concentrate, as is shown in Fig. I. This will be termed the solids concentration-solution dilution principle, or, for short, solution dilution. countercurrent decantation- type circuits. The second principle used in washing solubles from solids is that of solids concentration-solution displacement. Here the solids are restrained from movement while wash solution is forced through the interstices in a counter-current fashion, as in Fig. 2. In the simplest application of this principle, once the "cake" has been formed, it is not disturbed until the operation is completed. In continuous filters, the cake is merely moved under the successive washes and the displaced filtrates removed as in Fig. 4. Often, however, after one or two displacement washes, a repulping step is introduced, the cake reformed and washed again. This procedure brings the solution dilution principle into play as well as the solution displacement principle. Merely thickening ahead of filtration, which is often operationally advantageous, does not hybridize he circuit. It still can be a pure solution displacement operation from the washing

Jan 1, 1961

By John F. Knudsen

Following the flowsheet from the primary crushing plant of Ray mines division through the final products sample mill, there are eight exhaust systems ranging in size from 12,000 to 30,000 cfm. Where possible, hood face velocities are kept around 500 ft per min, permitting branch velocities of 2500 ft per min. Tight-fitting enclosures are provided over all ore drops, crushing operations, and vibrating screens. All enclosures are exhausted either primarily or secondarily, except those around conveyor head-pulleys where the ejector effect of the falling ore creates sufficient indraft to abate dust dissemination. IN 1947 an Industrial Hygiene Department was organized to represent and assist the four western mining divisions in industrial hygiene problems. Department headquarters are located at the Utah Copper Division, Magna Plant, Magna, Utah, with a branch office at the Chino Mines Division, Hurley, N. M. The headquarters staff includes a director, a department secretary, an industrial hygienist, a supervising ventilation engineer, and two ventilation designers. To be in closer association with work at the Southwest properties, a field engineer at the branch office conducts field studies which include ventilation problems at the New Mexico and Arizona properties;i.e., the Chino and Ray mines divisions. Functions of the department are to discover and evaluate existing hazards and to develop protective measures, either by personal protective devices or by proper ventilation, depending on the nature of the contaminant. Other than dust counting, all air samples collected at the four properties are processed at the home office. If through plant surveys or by suggestion of management some type of ventilation or air conditioning is required, the problem is usually handled by the ventilation section of the headquarters department, where general arrangement or line drawings are prepared, showing hoods, ducting, and equipment. Some hood and special parts detailing is done at headquarters; otherwise, required detailing is done by the respective plant engineering departments. Prior to the design of industrial ventilation, either new projects or the revamping of old ones, a thorough survey is made of existing conditions. In so far as possible weighted average exposures are determined and adequate ventilation provided on the basis of maximum allowable concentrations of the contaminant in question, as well as medical case histories, if these are available.

Jan 1, 1954

By H. Tabachnick, N. Hedley

The extraction of gold and silver from ores with alkaline cyanide solutions is well known. Cyanide solutions are also good solvents for many base metal minerals, particularly most of the copper minerals. Leaver and Woolf,1 who determined the solubilities of copper minerals in 0.10 pct sodium cyanide solution, showed that malachite, cuprite, chalcocite, and bornite are readily soluble in cyanide; least soluble are chalcopyrite and chrysocolla. The Mining Chemicals Laboratory of American Cyanamid Co. has studied the possibilities of using cyanide solutions for leaching base metals. In this article the authors present the results of their experiments with cyanide leaching to reduce the copper content of a zinc concentrate from 0.050 pct to the desired specification of less than 0.02 pct. Zinc Ore Sample: The sample of commercial zinc ore used in this investigation to produce zinc concentrates was ball mill feed ranging from 1/2 in. to fines. The ore was crushed to —10 mesh and riffled into 600-g charges for zinc flotation. Analysis revealed 4.54 pct Zn and 0.005 pct Cu. Examined microscopically, the ore consisted essentially of cream-colored sphalerite and carbonate gangue. It contained a small amount of pyrite, partly tarnished. The only copper mineral identified was chalcopyrite, mostly smaller than 20µ, some of which occurred as attachments on sphalerite. Flotation Procedure: Batches of zinc concentrates were made as required according to the following general procedure. A 600-g charge of —10 mesh ore was ground for 4 min at 60 pct solids in a laboratory steel rod mill. Screen sizing showed it to be all —35 mesh with 42 pct —200 mesh. The pulp was transferred to a Fagergren laboratory flotation machine, diluted to 25 pct solids and conditioned for 5 min with 0.6 lb per ton CuSO4, . -5H2O. It was then conditioned with 0.10 lb per ton Sodium Aerofloat promoter and floated for 5 min with pine oil as frother and creosote as froth stiff-ener. The pH during flotation was 8.5. A typical analysis of zinc concentrate subjected to leaching is 44.41 pct Zn and 0.051 pct Cu. The ratio of concentration was close to 10 to 1. Leaching Procedure: Aero Brand cyanide, technical calcium cyanide analyzing 49.5 pet NaCN equivalent, was used for all cyanide leaching tests. For each test three rougher concentrates floated as described were combined (total weight close to 180 g) and the water content adjusted to 150 ml. The percent solids in the pulp was thus 55. After a weighed amount of cyanide flakes had been added, the pulp was agitated on rolls for a given period, then filtered and washed. Filtrate and washed concentrate were assayed for copper content. The procedure for ammonia leaching was similar to the cyanide process. A series of tests was run in which the effects of ammonia as a solvent for copper in the zinc rougher concentrate were investigated. In each test 180 g of zinc rougher concentrate was leached with 150 ml of ammonia solution. Various strengths of ammonia and times of leaching were investigated. The results are shown in Table I. It is apparent that ammonia was a poor solvent for copper in the zinc concentrate; 60 min of agitation with a relatively strong NH:, solution extracted only 2 pct of the copper. CYANIDE LEACHING TESTS Effect of Solution Strength: The solvent effects of 0.125, 0.187, and 0.250 pct NaCN equivalent solutions were compared for leaching periods of 15 min. Residue and filtrate were assayed for copper content. The copper content of the filtrate plus wash was calculated back to the original volume of cyanide solution (150 ml). The effects of cyanide strength are given in Table II, It will be noted that 15 min leaching with 0.25 pct NaCN equivalent solution extracted 74.6 pct of the copper in the zinc concentrate. The leached product assayed 0.013 pct Cu, appreciably below the required specification of 0.020 pct. Effect of Leaching Time: Portions of zinc concentrate were leached with 0.25 pct NaCN equivalent

Jan 1, 1961

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By Z. E. Arlin, R. D. Lynn

A deep well injection system is used by The Anaconda Co. for the disposal of uranium mill tailing water near Grants, N. M. A 2511-ft hole was cored and tested through Triassic, Permian, and Pennsylvanian (?) sediments and bottomed in Precambrian granite gneiss. The disposal well was plugged back to 1830 ft and completed in 563 ft of sandstones in the Yeso formation. The reservoir sandstones contain water similar to the injected waste water, and are isolated from overlying fresh-water aquifers by an evaporite barrier zone. Mill tailing water is decanted, filtered, and introduced into the well by gravity at an average rate of 400 gpm. The reservoir has a life expectancy of 10 years. The Anaconda Co. began uranium milling operations near Grants, N. M. in 1953 with a small mill that processed limestone ores. A larger second mill was built in 1955 to treat sandstone ores. In 1956 it became apparent that a large tailing pond would be required to contain the increased discharge of mill waste water. Research was begun on supplementary methods of disposal by which a minimal pond size could be maintained to avert excessive seepage losses. An intensive sampling program was begun to monitor the fresh-water wells in the area. The original limestone mill ceased operation in 1959. The present mill treats sandstone ores by sulfuric acid leach and a resin-in-pulp ion exchange recovery circuit that uses chloride elution. Process waste water is discharged to a tailing pond where, after evaporation losses, an annual average of about 400 gpm are available for injection into the disposal well. The waste water is a mildly acid solution that contains large amounts of manganese, iron, and the sulfate and chloride salts of sodium, calcium, and magnesium. It is a low-level radioactive fluid that contains small amounts of Uranium-natural, Thorium-230, and Radium-226. The average chemical and radioactive analyses of the waste water injected into the disposal well are shown in Column B of Table I. Disposal of the excess mill waste water by deep well injection was investigated after extensive research had proved that alternate methods were not satisfactory. A study of the regional geology and hydrology indicated that a disposal well was feasible, and a test well to basement rock was planned. Tentative plans for the test well and the results of the geologic and hydrologic studies were submitted to the New Mexico Dept. of Public Health, the New Mexico State Engineer's Office, the U.S. Atomic

Jan 1, 1962

By C. B. Sclar and

A graphical solution is presented for the equation v =v &-cU where vb is the volume of liquid b of density 6 that must be added to liquid a of volume va and density d, in order to obtain a heavy-liquid solution of preferred density dm for mineral fractionation. The equation is valid only for pairs of liquids whose volumes are additive, but empirical density-composi-tion data show that this condition is met over wide compositional ranges by all of the heavy solutions that are commonly used for mineralogical analysis. The chart is a nomograph which consists of two horizontal volume scales ad a vertical density scale arranged so that one volume scale occurs on each side of the density scale. All the scales are linear. For two liquids of density d, and &, respectively, each volume scale has an independent level on the density scale, ad the graphical solution for vb on the nomograph is obtained by construction of one straight line. The chart can be prepared easily to cover any density range with any desired accuracy by proper selection of the scales. Heavy-liquid separation of particulate samples is an indispensable analytical procedure in the mineralogical and mineral-process ing laboratory. Heavy liquids may be used 1) to isolate specific minerals in the form of high purity products or to fractionate samples into several products with density limits for petrographic, chemical, spectrographic, and X-ray diffraction analysis,'-' 2) to determine the density of minerals,'-l4 3) to facilitate the recognition and identification of optically similar associated minerals,15 and 4) to determine quantitatively the degree of liberation of ore minerals in ores and mill products at various limiting sizes." The preparation and recovery of heavy liquids suitable for mineralogical analysis are discussed fully in the literature and operational procedures and special equipment for heavy-liquid separation are described in numerous references.'747837' 13,18,25-42 Useful tabulations of heavy liquids for mineralogical analysis are given by Tickell, Mil-ner,' Twenhofel and Tyler,' and Lange and a very complete up-to-date list of minerals arranged according to increasing density is given by Mursky and Thompson. USEFULNESS OF THE DENSITY CHART For any particulate sample, the limiting densities selected for its fractionation by means of heavy- liquid separation depend on the respective densities of the constituent minerals and the specific objectives of the separation. In many instances, the densities of readily available and practicable heavy liquids do not coincide with those that are required, and suitable liquids of the proper density are obtained by dilution with miscible liquids. In the general case, one may wish to mix either a pure liquid (A) or a solution of two miscible liquids (AP,,) of known density with either a pure liquid (B) or a different solution of the two miscible liquids (A,B,) of higher or lower density in order to obtain a final liquid of the preferred density. In conventional practice, the latter is reached empirically by trial-and-error addition of increments of one liquid to the other. The density of the final solution may be determined either by accurately weighing a known volume of the final liquid,'' 532;4;40, or by means of I)a Westphal balance, 2)a hydrometer, a refractometer in the case of binary liquid systems for which density-refractive index data are available,15 4) natural or synthetic .indicators of known density, a pycno-meter. Like all trial-and-error methods, these procedures are time consuming and many require special equipment which may not be available, The purpose of this paper is to show that the volume of a liquid of known density which is to be added to another liquid of known volume and density in order to obtain a solution with an intermediate preferred density may be determined rapidly and accurately by a graphical method provided that the two liquids form ideal or quasi-ideal solutions whose volumes are additive. Empirical data47'8~'8~4B'49 show that solutions prepared from pairs of miscible

Jan 1, 1961

By M. F. Williams, L. G. Hendrickson

IN classification of pulps bearing magnetized ferromagnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in floes. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used. At the Research Laboratory of Oliver Iron Mining Div. in Duluth a method was developed for measuring depolarization of the pulp of ferromagnetic material. Experiments were made with Mesabi taconite,' a natural magnetite of low coercive force. Ferromagnetic materials of higher coercive force, such as lodestone or the artificial magnetite produced by reduction roasting of hematite, present a more difficult problem, which was not within the scope of this investigation. It is possible, however, that some of the techniques evolved for measuring and calculating electrical characteristics of alternating current coils would be of use in depolarizing high coercive force material, particularly in conjunction with high-frequency alternating current, as proposed by Hartig and others.'," Properties of Ferromagnetic Materials:'7 Experimental work, described below, has shown that if a sample in the magnetized state is heated above the Curie point and cooled, much of the preferred orientation is destroyed and the sample is substantially depolarized. It has been thought that when the sample cools below the Curie point the domains cancel each other, leaving a zero net moment. However, such particles still exhibit a tendency to cohere, and undoubtedly this is caused by the forces of residual magnetism. -AS measured by the percent depolarization, this tendency is reproducible for any sample upon repeated heating above the Curie point and subsequent cooling and is independent of the initial state of magnetization. It is postulated, therefore, that as the material is cooled below the Curie point the domains in any particle do not completely cancel each other, but rather are preferentially oriented to some extent. Mechanism of Depolarizing with Alternating Current Magnetic Fields: It is believed that when ferromagnetic material is passed through an alternating magnetic field, depolarizing occurs in the decaying portion of the field. As the particles pass through the portion of highest intensity they become magne- tized. If the particles are not free to move, the polarities of the particles will be reversed (by a mechanism similar to that described above for magnetism) at a frequency equal to that of the applied field. As the material moves through the decaying field, intensity levels become such that a domain does not completely reverse, but stops on an axis of easy magnetization. By the time the material reaches the point of zero field intensity, a state of fairly random orientation of domains is achieved. If conditions are such as to give a completely random orientation, the particle will have little or no external magnetic field, and a pulp of such particles will be depolarized. Previous Work In 1918 E. W. Davis was granted a patent for demagnetization of magnetite pulps.' His method consisted of passing the pulp through a tapered coil, activated by alternating current of normal frequency (60 cycle). This method, with minor modifications, has been used almost universally in all pilot plants and commercial installations in which depolarization of low coercive force materials has been required. Hartig, Onstad and Foot2,3 avd made a detailed study of the factors involved in depolarizing both low (below 100 oersteds) and high (above 100 oersteds) coercive force material. They developed a method for evaluating the relative degree of depolarization of any pulp based on the settling characteristics of the pulp. Their standard of comparison was a sample heated to above the Curie point and cooled in a zero field, all in a neutral atmosphere.* For low coercive force material they found treatment.Thisprocedure is subsequently called, in this report,theCurie that results equivalent to Curie treatment could be

Jan 1, 1957

By P. J. Carroll, H. Colijn

Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. Feeder load, material properties, feed rate, physical layout, and environment as well as first cost determine the selection of feeder type. This paper provides a new method of calculating feeder loads with some experimental data as verification. General design criteria for belt and apron feeder, rotary table and plow feeders are discussed and a special section is devoted to vibratory feeders. Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. During the past few years various papers have been written and presented on feeders and their application.1-9 This paper will be confined to some specific bin-feeder design criteria such as feeder load and power requirements. Special attention is given to the basic design criteria for vibratory feeders. HOPPER AND BIN DESIGN Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. A lot of effort has been devoted in the past decade to the development of functional design criteria for hoppers and bins.1,10 The integrated concept of bin and feeder design requires quantitative analysis of the bulk material characteristics before the design and the selection of components can be attempted. The design of a feeder system must begin with the proper dimensioning of the hopper outlet to prevent arching or ratholing. The hopper opening should be large enough to allow passage of the bulk solid at the required maximum discharge rate." A feeder can only throttle the flow. FEEDER LOAD DETERMINATION Over the past ten years, there have been various attempts to determine the exact load or pressure on feeders mounted directly under hopper openings. Many designers, however, still consider this pressure equal to the hydrostatic head of material above the opening, and because such pressure would be very

Jan 1, 1969

By H. M. Zoerb

Based on the belief that operating details are a definite contributing factor to major economies, this paper traces the development of crushing cavity design in Symons cone crushers to attain maximum liner utilization. Wear rates are analyzed and compared in this presentation and drawings illustrate succeeding design changes. IN these times of rising labor and material costs, it has become more and more necessary that attention be paid to some operating details which, in their obscurity, may he the key to major economies. Liner wear in crushing cavities of secondary and tertiary crushers can become an appreciable cost item when the material to be crushed is hard and abrasive. This item of cost not only includes the value of the crushing members, but also more intangible costs such as labor and lost production due to more frequent replacement. The variables which are encountered in ores and minerals to be reduced; the design of plant and machine application; the sizes, shape, and fineness, characteristics of the crushed product; the moisture; hardness; friability; and abrasiveness of the material to be crushed are all influencing factors which must be taken into consideration in the selection of a crusher, and particularly in the design of crushing cavity and liners to be used in a crusher. Through a research program undertaken in cooperation with many operators of Symons cone crushers a new approach to crusher cavity design was made, resulting in the development of liners for specific operations which showed: 1—maximum utilization, as high as 70 to 80 pct of original weight of metal, and 2— maximum capacity of unit during the greater portion of its life. It has been found that liners so designed for a given operation will show added economies in power consumption, maintenance, and general wear and tear on the crushing unit. Initial work in the so-called tailoring of crushing cavitles was begun on the tertiary or fine crushing units where as a rule reduction ratios were low, varying from 3 to 6. Parallel or sizing zones in the lower portion of the crushing cavity were too long, resulting in a tendency to pack. It was found that very little additional crushing was done in the parallel zone after the initial impact in that zone and that a relatively small amount of' additional crushing was done by attrition, which required very careful feed control. A small amount of over-feeding would result in packing which not only consumed power but caused unnecessary liner wear as well. The illustrations which follow in this discussion will show only contours of crushing cavities, and for purposes of simplification the cavities will be considered only in their closed position. The first step, therefore. was to reduce the sizing zone to a minimum. This was done by removing the lower portion of the liner as shown in Fig. 1. The result of the change was a saving of 15 to 20 pct in liner cost, less power consumption, with no change in capacity. This change in design, while an improvement, did not go far enough. As wear took place, the change in the liner was not uniform throughout its entire length, resulting in a restriction of the feed opening and thereby loss of capacity. Furthermore, progressive wear of the liner had the effect of lengthening the parallel zone until finally the entire crushing cavity was all parallel zone, see Fig. 2. It is obvious from the reduced feed opening of the worn liner that the ability of the machine to receive material is lessened considerably. Furthermore, the long parallel zone with its worn, irregular profile did not operate at its highest efficiency. The first attempt to overcome this difficulty was carried out on a 5 1/2-ft crusher installed in a plant producing roofing granules. The material being crushed was a very hard graywacke and the crusher was closed-circuited with a screen having .232-in. slotted openings. A radical change in contour was developed, as illustrated in Fig. 3. Equal wear lines on both concave and mantle are designated 1, 2, 3, etc. The method of development of this contour is as follows: Since adjustment for wear is vertical, corresponding intersections of wear lines and vertical lines developed concave and mantle contours which maintained equal but lengthening wear surfaces in the parallel zone. The ideal contour, of course, is one in which the length of the parallel zone remains constant, but because of present foundry practice and heat treating characteristics this is impossible.

Jan 1, 1954

By Nathaniel Arbiter, Norman L. Weiss

Factors now accelerating the trend to larger concentrators and larger equipment units are reviewed. After almost 40 years of stability with unit sizes less than 100 cu ft, 200 and 300-cu-ft flotation-cell units are now operating and a 500-cu-ft machine is being built. The design of these cells is considered, as is the design and operation of flotation circuits against the background of the need to achieve greater process efficiency while holding down operating and investment costs. Particular attention is paid to the scale-up problem. With the newer cells having five to ten times higher unit capacities, the advantages resulting from this in sampling, mill operation nnd control, testing and plant layout are indicated, as well as the broad direction for changes in the overall design of 50,000 to 100,000-tpd concentrators. A comparison is given of the available larger cells of U.S. manufacture with analysis of differences and similarities. After almost 60 years of application in this country, froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups, the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign, the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency. and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum—to mention only the most important metals occurring in the U.S. as sulfides- must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000-tpd milling rate on copper ores. Table 1' shows the trend in copper ore grades in U.S. in recent years. Table 2' shows the projected annual growth rate of consumption 1966-1985. A study by one of the authors 25 years ago showed that of 32 copper mills in North America with more than 100-tpd capacity, only eight had capacities exceeding 10,000 tpd. The average for these eight was 25,000 tpd. These included the three giants of that day, Magna, Arthur, and Morenci; the other five averaged a little over 10,000 tpd. Today instead of the eight mills with capacities exceeding 10,000-tpd capacity we have 25, and the mill with less than 1000-tpd capacity is fast becoming extinct. Much less range is found in lead and zinc mills, which are still generally small except for the few with over 1000-tpd capacity in Missouri, Utah, and Idaho, and a few zinc ore mills in the same size category. Molybdenum and potash operations are the fastest growers in North America today, but when one considers the projected increase in consumption of copper together with the projected decrease in grade of ore (3% annually), he can foresee that copper ore milling will soon lead the list. Technological improvements to meet the challenge of lower-grade ores have taken the wholly predictable path toward bigger equipment. In mining, shovels, draglines, scrapers, and trucks have led the way; in ore processing, we have seen a rapid increase in size of grinding mills, flotation cells, and pumps. Twenty-five years ago, for example, the 10-ft-diam ball mills treating 2000 tpd at Morenci were considered the giants, but today some grinding mills in similar service have five times that capacity. The specific matters to be dealt with in this paper are 1) the underlying principles that affect flotation-machine design, and the conditions required to produce

Jan 1, 1971

By Rollin A. Slater

This paper presents a composite of ideas on materials handling systems by describing the design of an over-all system for a hypothetical steel pellet plant located on the Great Lakes. The bulk materials handling industry has served for years as the skeleton and the central system of nerves and nourishment for the body of basic industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. Materials handling technology has likewise improved its techniques and currently has a new, stronger generation of equipment to perform its necessary supporting function. Drawing upon excerpts from several recent plant designs, this paper describes a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details are not available for publication, and therefore the plant described herein is a composite of ideas. This imaginary plant will be located on the United States side of the Great Lakes and its owner will be called the Hypothetical Steel Corp. for purposes of discussion. TYPES OF EQUIPMENT The basic bulk materials handling systems and components required in a plant so situated are: lake boat unloaders; railroad train unloading systems; storage pile stackers and reclaimers; large bins and regulating feeders; and the conveyor systems — with their attendant controls— which connect the foregoing. PROGRAM OF DEVELOPMENT The initial work on the plant must be that of the process engineers who develop and refine the basic data, i.e., the logistics of all raw materials, waste materials and products within the plant. During this phase of study, the materials handling engineer may advance his planning only in basic areas such as movements at the dock and movements at the railroad. This initial planning work is concerned only with defining logical plant locations in the light of channels, currents, existing traffic, governmental regulations, locations of existing railroads and available rights-of-way. These systems alone have their own individual criteria which must be respected and accommodated in the final layout. All other elements, such as the arrangement of the blast furnaces, power house, coke plant, by-product plant, scrap preparation plant, BOF shop, and facilities for continuous casting, degassing, calcining, etc., are dictated by their own specific needs and their relation to each other. In the arrangement of these latter facilities, the materials handling system is secondary and must be designed to accommodate. BASIC LOGISTICS The result of the process engineer's work can be expressed in terms similar to those shown in Table I. Plants are customarily rated in terms of annual tons of ingots. Therefore, the basic size of this plant can be determined by referring to the BOF Shop wherein it is sized at 5 million tpy. From the base, the required hot metal can be traced to the blast furnace, which in turn indicates the amount of required flux, iron bearing materials and coke —which in turn establishes the demand for coal. Likewise, the total demand for flux can be determined by the combined demand of the lime plant and blast furnace. The generation of fines and waste products, which have significant value but are not usable as such, create the need for a sintering plant. From projections such as the foregoing, the complete flow of materials can be established and accommodated. The basic premise upon which this typical materials balance is predicted is that the plant will be a producer of high tonnages of non-SpecialtV- products. All basic raw materials (flux bearing, iron bearing, coal) will be prime quality. For example, the basic iron charge will be pellets, and the iron ore fraction will be sized lump, all of which

Jan 1, 1970

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By M. C. Fuerstenau, A. M. Gaudin

A homogeneous suspension is viewed by X-rays. The radiation density seen, affords a measure of the extra absorption due to the solids contained. This radiation density, at a predetermined depth, varies with time. The chart of this relationship gives the desired determination. s it is frequently necessary to know the distribu-rt tion of particle sizes in various products used in industrial applications, a number of means have been devised for these determinations. Some of them include direct microscopic measurement, screening of product, extraction of samples from a settling slurry, air and liquid elutriation, adsorption of gases and liquids, and light absorption. The absorption of light as a means for particle size analysis has been known and employed for some time. X-ray absorption has not received the attention that light has enjoyed primarily because of the complex and costly instrumentation involved with X-rays. In 1954, Brown and Skrebowskil suggested the use of X-rays for this type of determination but did not supplement their suggestion with experiment. In 1958, the authors conducted size analysis experiments on suspensions of quartz with the Trans-viewer: an X-ray unit specifically adapted for sedimentation research, and Rossa conducted experiments in a similar manner in 1959 with a stable gamma emitter, AmZ4l, on suspensions of uranium oxide. To illustrate the applicability of X-ray absorption for analyzing particle size distributions, an essentially mono-energetic and well collimated X-ray beam was used as a source. The beam was made mono-energetic by placing a zirconium filter before the counting window together with feeding the pulses from the proportional counter into a reverter, a device capable of discriminating against pulses of various heights. The sketch in Fig. 1 shows the collimation arrangement in more detail. As shown, the X-ray beam was collimated by inserting a 3/8-in. ID pipe into one of the ports of the X-ray tube and further by two small steel plates with slits 3/32-in. wide and 1/2-in. long placed in front of the window of the Geiger-Mueller (G-M) tube. One of the plates was located 1/2 in. and the other 2 1/2 in. from the window of the counter; both plates were contained in an aluminum holder mounted on the box containing the G-M tube. This type and degree of collimation should eliminate any intensity due to scattered radiation; the transmitted intensity would then be solely a functior. of the absorption by the suspension at that level. Experimentally, homogeneous suspensions of finely ground quartz were prepared, Daxad (a sulfo-nated compound made from wood) was added as dis-persant, and the transmitted X-ray intensity measured as a function of time at a fixed depth in the suspension. In more detail, the experimental procedure involved the following: 1) measuring the transmitted X-ray intensity through the Daxad solution at a predetermined position or settling depth in the absence of solids, 2) placing a known amount of dry solids into the vessel and agitating thoroughly, 3) measuring the transmitted X-ray intensity at time zero (i.e., immediately upon cessation of stirring), and 4) measuring the transmitted X-ray intensity as a function of time (a 10-sec counting interval being chosen and counting being started 5 sec before the desired time). Since a linear relationship exists between percentage solid in a slurry and the logarithm of transmitted intensity for a homogeneous material, the cumu-

Jan 1, 1961

By William Lodding

Muscovite was the crystalline material used in the experiments discussed in this paper. It was both wet and dry ground for various periods of time. The effects (physical and chemical changes) produced in grinding are analyzed by use of thermal analysis. That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Mackenziel and Bartha2 reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding and, on the other hand, existing strain may be released by the same process, as shown by Holt, et a1.3 All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze, by the use of thermal analysis, some effects produced in grinding. In differential thermal analysis (DTA) one measures the sum of all thermal changes occurring in a substance during heating or cooling; e.g., chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and thermal conductivity, strain release, etc. By thermogravimetric analysis (TGA), on the other hand, only chemical changes involving weight loss or gain are recorded. Similarly, gas evolution analysis (GEA) will register only reactions involving gas evolution. By performing two or all three of these methods of thermal analysis simultaneously and on the same specimen, one can separate the different effects registered and, by difference, evaluate their magnitude. The results of TGA are usually plotted as percent weight against furnace temp. When one differentiates weight against furnace temp, a rate of weight-change curve is obtained, and the resulting differential thermogravimetric (DTG) plots are similar in appearance to DTA thermograms for the same reaction. While the integrated area under a DTA peak represents enthalpy and can be expressed in calories per gram the area under the corresponding DTG peak represents the weight change which took place during a reaction. The similarity of DTA and DTG thermograms obtained from one material can be seen in Figs. 1 and 2. EXPERIMENTAL A Fisher mortar grinder and a porcelain mill with burundum balls were used for both dry and wet grinding. Muscovite was first carefully hand-filed and screened on 20 and 100 mesh. The middle fraction was considered essentially unaltered muscovite.

Jan 1, 1968