Search Documents

By Clarence Zener

[ ] THE present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 27 to 30. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1946

By W. S. Holt, E. T. Tkac, R. A. Grange

QUANTITATIVE knowledge of the time element involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 135-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Ae3 and Ae1), the temperature range of martensite formation, and the end-quench hardenability. These data are directly applicable to the heat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. MATERIAL All specimens were prepared from a 13-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: Mn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, i.57: MO, 0.36: Al, 1.26. The forged bar was normalized from 1750°F (955°C) and then tempered for one hour at 1200°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. EQUILIBRIUM TRANSFORMATION TEMPERATURES In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Ae3, and the maximum temperature at which austenite is completely unstable, Ae1, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1946

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

By Donald D. Smythe

Tars paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point 90 km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of São Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a by-product of kaolin mining. These deposits, and, a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé. The first is 190 km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriaé area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto

Jan 1, 1946

By G. L. Kothny

DEVELOPMENTS of well-surveying instruments, coring and core orientation, were in an advanced state when drilling for oil began-these developments actually originated with the mining industry.1 Surveying of oil wells was not generally used in the United States until Alexander Anderson2 disclosed that the majority of wells drilled with rotary tools were crooked, with average horizontal drifts of about 516 ft. for holes 5000 ft. deep and about 793 ft. for holes 6000 ft. deep. This disclosure brought about the development of many additional instruments for surveying oil wells during the progress of drilling and after their completion. Surveying of boreholes, during the process of drilling at regular depth intervals, became a standard practice in the petroleum industry. Some producing states even established laws making check surveys mandatory, during drilling and under certain conditions also after completion. The surveying of boreholes also brought about changes and improvements in drilling practices. It provides information for the guidance of the hole while drilling, and for plotting the course as the work progresses, enabling the driller to take corrective measures immediately and with the least expense. The reasons for drilling straight holes are too well recognized to warrant any full discussion of them here. Straight holes are less costly to drill, because [ ] they reach the object on the shortest course. Table I shows the horizontal drift and loss in vertical depth for various angles of inclination. It is not surprising, therefore that many drilling contracts for oil wells today limit the drilling contractor to a maximum inclination off the vertical of 2° or 3°. In the mining industry the reasons for drilling straight holes are still more serious. A crooked hole may miss an ore body underground or provide incorrect information regarding an ore body. TYPES OF SURVEYING INSTRUMENTS The surveying instruments used in oil-well drilling may be classed in two types: I. Inclinometers, recording inclination only.

Jan 1, 1946

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

By R. G. O’Meara, M. M. Fine

ONE of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.[t] In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.1 The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 ACKNOWLEDGMENT This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. O. E. Anderson, mill superintendent,

Jan 1, 1946

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,000. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service.

Jan 1, 1946

By R. S. Pratt

IT is proposed to discuss the materials and furnaces, as well as the melting procedures used in preparing metal for casting billets, bars or cakes for mill fabrication. As far as possible, consideration will be given to the alloys that are commonly made in most brass mills producing strip, tube, rod and wire. RAW MATERIAL The basic raw material for such mills, of course, is copper, which may be obtained in the form of ingots, ingot bars or cathodes. Refinery-cast ingots and ingot bars, which are simply double ingots, are supplied in accordance with A.S.T.M. Specifications as regular electrolytic or fire-refined tough-pitch copper. In the wrought-metal industry, the electrolytic brands have been preferred, although during the war large quantities of fire-refined coppers sufficiently pure to be suitable for all existing requirements were imported from South America. With the exception of Lake copper, most primary fire refined coppers produced in this country have not been considered satisfactory for wrought metal alloys. Cathode copper, which is now widely used instead of ingot copper for alloying, is the electrolytically deposited metal that is normally remelted in the production of electrolytic tough-pitch ingots. It is in the form of rough, flat plates not suitable for processing but quite satisfactory for melting when sheared into suitable sizes. Raw zinc is perhaps the next most important raw material and this is obtained in various grades, depending on the analytical requirements of the alloy to be made. The grades of zinc as outlined in the A.S.T.M. Specifications vary in cost with the amount of impurities-lead, iron, cadmium-and are purchased in such a way as to produce the most economical mixture consistent with the purity required in the alloy. Other virgin metals (lead, tin, aluminum and nickel) are used in varying quantities for making copper alloys. These elements can also be purchased in accordance with the appropriate A.S.T.M. Specifications where available. Also available are a number of special alloys, which are used as deoxidizers or as means of adding relatively small quantities of elements not suitable for adding directly as virgin metal. In this category are such materials as phosphor copper or phosphor tin, silicon copper, manganese copper, cadmium copper, and copper-iron or zinc-iron alloys. Some of these alloys may be purchased on a definite alloy basis or may be produced in the plant itself for its own use. For largely economic reasons, however, a great proportion of the charge to the melting furnaces consists of alloy scrap. In the production of many finished products, as much as 70 or 75 per cent of the metal originally cast may be discarded at various points along the production line. This material eventually finds its way back to the casting shop as mill scrap, overhaul or scalping chips, skeleton scrap, rod turnings, or miscellaneous fabricating scrap. One of the most serious problems in the

Jan 1, 1946

Jan 1, 1946

By E. C. Wright

THE following article is based on observation of college graduates entering the steel industry in technical work made during the past 25 years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many, colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel' plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training -in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers, it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry, physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature, and that students be taught to use theoriginal data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallography, etc., but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a, few weeks in a. plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1946

By J. R. Long, E. L. Anderson, R. S. Dean, F. S. Wartman

TITANIUM has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, 'methods required for its fabrication, and the properties that may be produced in this interesting metal. METHODS OF PREPARING METALLIC TITANIUM Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,2 van Arkel,3 and Fast,4 subsequently confirmed the facts that pure titanium is a ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent 'solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agents2 with sufficient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

[ ]

Jan 1, 1946

By Daniel S. Lyons

Jan 1, 1946

By Richard H. Zinszer

Application Of electric logs has been used in correlation of subsurface structure to determine the size and shape of the oil reservoir. Such a knowledge is hardly complete until saturation and productivity are determined for the various horizons. It is difficult to use electric logs successfully for this purpose because of the many factors that influence the curves. In this work an effort was made to establish an empirical correlation between formation resistivity for a series of electric-log curves and water saturation and oil productivity of sand. Electric logs were obtained by recording with 10 different electrode spacings through the same interval of a well. In the analysis of these curves all factors except two, a dependent and independent variable, were held constant. The interval studied had been cored and a large number of samples were analyzed in the core laboratory in order to compare the values of permeability and saturation with the measured values of formation resistivity. Results of this analysis indicate: (I) the depth to which mud filtrate enters a sand body, (2) a correlation between permeability and sand resistivity for shallow penetration depths, and (3) that the water saturation for an oil sand can be determined from the measured sand resistivity after making suitable corrections for sand thickness. The procedure in the last method depends on a correction for thickness factor and a theoretical curve. The accuracy of the theoretical curve is now being tested in the laboratory Introduction In an effort to place the analysis of electric logs on a quantitative basis, there is need for a better understanding of the many factors that influence an electric-log curve. These factors may be large differences in sand thickness, permeability of the sand, salinity of the interstitial water, mud resistivity, formation temperature, and other sources. A number of examples were presented by Archie,' which treat the effect of sand thickness on measured resistivity. He compared the true resistivity of a sand with the observed resistivity for sands 8 it., 16 ft., and 24 ft. thick, and found the observed resistivity of the 8-ft. sand to be approximately

Jan 1, 1946

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946