Search Documents

By W. T. Turrall, D. Porter

The paper describes a machine developed for the purpose of concentrating clear optical grade fluorspar crystal from a feed material containing less than 1 pct impurities. The principle of concentration is based on the fact that in a liquid having an index of refraction equal to that of fluorite (n — 1.434) clear crystals are invisible, whereas crystals containing occluded impurities absorb a part of the light. As the crystals pass through a light beam, undesired crystals give themselves away by creating a shadow on a photoelectric receiver. .The shadow is converted by the photoelectric cell into an electric pulse. An electronic circuit amplifies this pulse and commands the operation of a mechanical concentrator. Hp HE crystal laboratory, Dept. of Physics, Massa--*- chusetts lnstitute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF,) for use in growing synthetic CaF, crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF, crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO,, BaSO,, CaCO,, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, —4 mesh + 10 mesh, from a feed containing over 99 pct CaF,. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1953

By G. W. P. Rengstorff, R. B. Fischer

A study was made of the effect of impurities on the bend ductility of cast molybdenum. High purity molybdenum was repared by re-melting under high vacuum. The ductility of "transverse-grain" specimens indicated that intergranular brittleness decreased with an increase in purity of the metal. THE production of as-cast molybdenum with high ductility at room temperature would make working of the metal easier and increase the usefulness of the as-cast metal. Furthermore, a .knowledge of the factors that influence the ductility of as-cast molybdenum might be applied to the problem of making fusion weldments having satisfactory room-temperature ductility. Individual grains of commercial as-cast molybdenum are slightly ductile at room temperature. However, the presence of carbides at the grain boundaries may cause the metal to fracture in a brittle manner. This behavior has been discussed.' The amount and distribution of the impurities in as-cast molybdenum would be expected, from previous research on the metal, to have considerable influence on its ductility. Some effects of oxygen and carbon on the mechanical behavior of the metal were discussed by Parke and Ham,2 Woodside,3 and Zappfe. Landgraf, and Worden.4 Parke and Ham2 found that, if a sufficient number of molybdenum oxide particles were present at the grain boundaries, the intergranular cohesion was reduced to the extent that arc-melted molybdenum would rupture intergranularly during hot forging. They also found that if the oxygen content was less than 0.003 pct, the cast molybdenum was hot forgeable. It is suspected, however, that forgeable molybdenum may contain a small amount of oxide that could reduce the ductility of the as-cast metal at room temperature. Also, there is the possibility of the unfavorable distribution of other impurities having a detrimental effect on the ductility of cast molybdenum. The results of a study of the influence of purity on the room-temperature ductility of cast molybdenum are presented here. Vacuum Arc-Melting to Produce High Purity Mo One way of determining the effect of impurities on the ductility of molybdenum is to prepare and test metal as free of all impurities as possible. Accordingly, the present investigation was undertaken with this in view. Arc melting in high vacuum (less than 0.1 micron of mercury) was chosen as the method for reducing the impurities below the concentrations occurring in commercial molybdenum. Commercial arc melting of molybdenum is carried out at about 50 microns pressure. During the arc melting, carbon and oxygen in the metal react to form carbon monoxide. By virtue of the vacuum process, the partial pressure of carbon monoxide is maintained at such a low value that the reaction greatly lowers oxygen and carbon contents. An excess of at least 0.03 pct C is used in commercial arc melting to insure that the oxygen content will be below 0.003 pct. The excess carbon remaining after the deoxidation step forms carbides on freezing. Some of the carbides precipitate at the grain boundaries and, as will be shown, have an unfavorable effect on the room-temperature ductility. In the present work, only the small amount of carbon (0.003 pct) contained in the commercial powder-metallurgy molybdenum used for melting stock was present. Partial removal of oxygen from the melt probably occurred as the result of the volatilization of molybdenum oxides, or by distillation of oxygen at the high melting tem-

Jan 1, 1953

By L. A. Rapoport, W. J. Leas

The original Burkley-Leverett theory has been extended and a more detailed formulation of the waterflood behavior in linear horizontal systems is presented. Particular consideration has been given to the evaluation of capillary pressure effects and differential equations permitting an explicit evaluation of these effects have been derived. On the basis of the developed theory it is recognized that the flooding behavior is dependent upon the length of the system and the rate of injection. At the same time it has been determined that systems of different lengths yield the same flooding behavior if the injection rates and or the fluid viscosities are properly adjrrsted or "scaled." It has also been found that the sensitivity of the flooding behavior with respect to rate and length decreases as any one of these {actors increases in value and that for sufficiently long systems and high rate.; of water injection the flooding behavior becomes independent of rate and length. or "stabilized." To such stabilized conditions the theory formulated by Buckley and Leverett is applicable. A number of laboratory flooding tests have been made and good agreement Iraq been found between theory and experimental observations. The experimental results are discussed and it is shown that under field conditions the flooding behavior is usually stabilized. As a result of these finding; a procedure is indicated for evaluating field performances either on the basis of tests performed with commonly available core samples or by means of calculations using relative permeability data INTRODUCTION In recent years the development of methods for evaluating oil recovery by waterflooding has been the object of considerable research. A theoretical analysis of the mechanisms involved in the displacement of immiscible fluids was originally established by Buckle!- and Leverettl and experimental investipatio~~s have been made by numerons workers." Many of the experimental results are in mutual agreement and bear out several significant features of the flooding mechanism as predicted by theory. Thus it lias been generally recognized that a flood corresponds to the movement of a steep saturation hank or "front" (primary phase), followed by additional gradual oil displacement (subordinate phase). It has also been found that for any porous medium the flooding behavior is largely dependent upon the oil-water viscosity ratio and that for increasing values of this ratio the relative importance of the primary displacement phase decreases while that of the subordinate phase becomes more pronounced. Although the studies to date have clarified certain aspects of the flooding process. they have given rise to observations of a somewhat contradictory nature that cannot he explained in terms of the original theory. These observations pertain mainly to the effect of injection rate or pressure gradient upon recovery. Some investigators report laboratory tests that indicate incresing oil recoverieq with increasing rates of water injectill, others find the flooding behavior to be independent of and other. mention lower oil recoveries with increased injection rates.3 The conflicting evidence indicated above creates considerable uncertainty with respect to laboratory testing procedures and the utilization of the resulting data for field evaluations. The principal purpose of this paper, then, is to resolve these Uncertainties by means of a comprehensive theoretical and experimental investigation of the flooding meanism. THEORETICAL DEVELOPMENT Derivation of Flooding Equations The mathematical description of transient flow phenomena is based upon the consideration of the various processes occurring during an infinitesimal time interval in an infinitesimal volume element and upon the correlation of these processes with those occurring in the adjacent elements. The volume elements are defined as being infinitesimal in comparison to the overall dimensions of the porous system, yet each sufficiently large so aS to encompass the full range of pore openings encountered throughout the system. If a porous system can arbitrarily be subdivided into an infinite number of volume elements all possessing the same distribution of pore openings and if this distribution is unformly continuous. the system may be said to be homogeneous. Such a homogeneous porous medium is considered in the present studivs. It is furthermore postulatecl that only oil and water are present in the pornu wediu. that they act a- totally incompressible and immiscible fluids. and that gravity effects are negligible. In n linear flow system of unit cross sertional area. as treated here. the infinitesimal volume element.; to he considered are cylindrical ".slices" of thickness dx. oriented perpendicularly to the direction of flow. The equations applicable to any such volume element. at my time. describe the movement. of oil and water across the element:

Jan 1, 1953

By G. F. Huff, G. R. Bailey, J. H. Richards

An improved bomb-sampling technique for obtaining samples for oxygen analysis from liquid steel is described. Analyses of samples taken from open-hearth furnaces by the improved method show sufficient agreement with laboratory data to indicate the accuracy of the method is better than that of other existing sampling methods. THE bomb-sampling method of determining the oxygen content of a liquid-steel bath was studied by obtaining and analyzing more than 200 samples from normal open-hearth heats. Of these samples, about 60 were obtained with a bomb of conventional design;' the remainder were taken with a somewhat modified bomb designed to give greater protection against slag contamination. In the new device, the contacting faces of the cast-iron mold halves are machined so that they fit closely; the opening at the top of the bomb is covered with a thin steel cap; and the top of the bomb is further covered with a wood block held in place by heavy steel wire. After the bomb has passed through the slag layer and has entered the steel bath, the wire melts and the wood block floats to the surface. Thereafter, the steel melts through the thin cap and flows into the bomb cavity where it is deoxidized with aluminum wire. An assembled bomb, ready for sampling, is shown in Fig. 1. To standardize sampling procedure, the samples were usually taken through the center door and at the bottom of the furnace; that is, the bomb was on the bottom when the metal cap melted. After each addition to the furnace, at least 20 min elapsed before a sample was taken. The oxygen contents of all the samples were determined by using the vacuum-fusion method, two or more specimens from each sample being analyzed. The specimens were cubes of metal cut from a region in the interior of the bomb sample, as shown in Fig. 2. Drillings for carbon analysis were obtained immediately above the oxygen-analysis region. Reproducibility of Results In determining the reproducibility of the results obtained with the modified bomb, the following four factors were studied: 1—variation in the oxygen concentration of duplicate specimens taken from a single sample; 2—variation in the oxygen concentration of duplicate samples taken in quick succession: 3—effect of the amount of aluminum wire

Jan 1, 1953

By N. T. Burdine

Formulas for calculating relative permeability from pore size distribution data are derived from basic laws of fluid flow ill porous media. The tortuosity factors that appear in the equation5 are described in. terms of the physical properties of tile medium and the saturations of the contained fluids. Procedures for calculating and methods for measuring the tortuosity factors are discussed. Values of relative permeability calculated by the formulas art: compared with results obtained by experimental measurements I INTRODUCTION Recently, several investigators have derived relative permeability equations from Darey's and Poisenille's Laws in which some, physical factor or factors describing the porous system appear. The factor that has caused the greatest amount of comment, and which is probably least understood, is the tortuosity of the fluid {lath ill the porous sample. Values of the tortuosity factors appearing in the equations range from a constant for all condition- of the fluid flow system to an inverse function of the pore radii. It is the purpose of this paper to compare wine experi~i~cntslly determined relative permeability curves with those calculated by a method which utilized capillary pressure infortmation. The capillary pressure data were obtained prefer.. ably from pore size distribution information as determined by mercury injection but. in some cases, in the absence of suitable mercury injection information. data were taken from measurements made by the porous semi-permeable diaphragm method. The physical significance of certain tortuosity concepts is inferred and the determinations of the tortuosity factors from pore size distribution data and by electrical measurements are discussed. THEORETICAL BACKGROUND In previously reported studies on pore size distribution in petroleum reservoir rocks. by the author and co-workers ail equation was derived relating specific permeability. k, to pore entry radii, R, porosity. . tortuosity factor. .,, and incremental pore volume. V. The equation is where being the "effective" length of the flow path in the porous sample. and L the length of the porous sample., The constant. 0.126. is a units conversion factor. (This definition of tortuosity factor X, = L L does not conform to all such definitions found in the literature. Fly similarity, in a two-phase system. the effective permeability of the wetting-phase.

Jan 1, 1953

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution.

Jan 1, 1953

By Lincoln F. Elkins

The Spraberry Trend Field of West Texas was discovered in January, 1949. Drilling of 2.234 wells and production of some 45 million bbl of oil by January, 1953, indicated this to be an important field which will ultimately cover more than 400,000 acres. In addition to being the world's largest field in areal extent, the Spraberry has presented many problems in well completion and operation and has demonstrated unique reservoir performance characteristics. The pay section consists primarily of a few fine grained sandstone or siltstone members in a thousand-ft thick section of shale, limestone. and siltstone. Since porosity averages only 10 per cent and nearly all permeabilities are less than 1 md, conventional core analysis does not delineate the "pay" section. Mercury injection was used as a capillary pressure test adaptable to rapid routine use to select those intervals having low enough connate water saturation to contain commercially significant oil saturation. In the central area of the field this "pay" amounts to 16 ft of Upper Spraberry and 15 ft of Lower Spraberry sands. An interconnected system of vertical fractures, observed in cores, provides the flow channels for oil to drain into the wells hut most of the oil is stored in the matrix since the void volume of fractures is estimated to be less than 1 per cent of that in the sand. Initial potentials of wells range up to 1.000 B/D after fracture treatment which should be compared with estimated capacity of 5 to 10 B/D if oil had to flow into the wells through the sand itself. Without exception initial pressures of later drilled wells were significantly lower than initial pressures of earlier drilled nearby wells in a large area some 6 miles long. This means the earlier drilled wells had drained fluids from areas much greater than their 40-acre proration units. Since most of this performance occurred while the reservoir pressure was above the. saturation pressure it was analyzed by the compressible fluid flow theory. This analysis gave calculated initial presrilres which agreed within 30 psi of measured pressures of 60 per cent of wells in the area using 16-md permeabilitv corresponding to a fracture system substantially that indicated by cores and using combined compressibility of rock and its contained oil and water corresponding to the core analysis data. The most important feature of this analysis was the very close agreement between effective compressibility of the rock and its contained oil and water from the field performance and that from the core tests, because it meant there are no "islands" of low permeability reservoir rock left untapped in the inter-well area and thus no additional wells are necessary to insure that at least one well penetrates each "reservoir." Twenty-five of forty-four 40-acre spaced wells on three contiguous sections were wed in a four-month inteference test. Six shut-in well. were tested monthly for oil production. productivity index. gas-oil ratio and pressure buildup, and seven shut-in wells were tested for decline in reservoir pressure. Tests on 12 regularly producing wells gave comparative data for interpretation of shut-in test wells. Reduction in reservoir pressure, decline in productivity index. and increase in gas-oil ratio were found to be substantially the same in the shut-in test wells as those in the comparative regularly producing wells, meaning that the producing wells were depleting the

Jan 1, 1953

By Robert Lowrie

Nine intermetallic compounds were tested in tension at various temperatures. Seven exhibited extensive plastic deformation at elevated temperatures. Correlations of tensile strength and elongation are attempted with melting (decomposition) temperature, valence electron configurations of the component elements, heat of formation, crystal structure, density, and volume decrease accompanying compound formation. A LTHOUGH intermetallic compounds have been -tX known for many years, the study of their mechanical properties, particularly in tension, is just beginning. The problem has been unattractive because of the well-known, erratic behavior of brittle materials tested in tension. The strong influence of surface or internal flaws as stress raisers in non-ductile materials and the effect of eccentricity of loading in superimposing bending stresses on the state of tension in the specimen are extremely difficult to mitigate and impossible to completely eliminate. Thus, tensile properties determined for brittle materials, such as intermetallic compounds at temperatures low in comparison to their melting points, are at best only general guides to the values to be expected in an ideal test of a perfect specimen of the material. It is, nevertheless, surprising that apparently no attempt was made to follow up the pioneer work of Tammann and Dahl1 in this field. Working with crude apparatus, these investigators succeeded in showing unequivocally that at temperatures sufficiently close to their melting points (from 75" to 400°C for the compounds tested) intermetallic compounds did exhibit plasticity. This was indicated by the appearance of slip lines on the surface of the specimen. No observations of strength were made in these tests, which were of a compressive or indentation type. Rossi2 in 1932 attempted to study the physical and mechanical properties of single crystals of a group of intermetallic compounds. However, he was able to prepare only one material, Cu2Z8,, in the form of large, defect-free, single crystals. Thus, he was able to report only the relative fragility of the compounds at room temperature. He reported one compound, Ag,Zn,, to be somewhat plastic at room temperature and Cu,Si to be friable, the latter in agreement with results reported herein. Although test results are available only in classified literature, it has also been announced that MoSi, possesses some ductility at elevated temperatures." In 1948 and 1949 Savitskii and Savitskii and Baron -ublished their work on the hot extrusion of Mg-Zn, Al-Mg, and Cu-Zn compounds. Under the favorable state of stress existing for this process MgZn, MgZn,, MgZn,, ß (Al-Mg), ? (Al-Mg) and 0 (Cu-Zn) could be reduced by amounts up to 90 pct at elevated temperatures. These authors also report that hardnesses of Mg-Zn compounds decrease from room temperature values of about 300 kg per sq mm to 30 to 50 kg per sq mm at 325°C. They found that alloys consisting solely of one Mg-Zn compound were most resistant to softening on heating, mixtures of a compound and eutectic less resistant, and mixtures of two compounds least resistant. The more rapid softening of mixtures of

Jan 1, 1953

By P. A. Beck

ACCORDING to the traditional definition,1 re-x crystallization is a process taking place upon annealing of cold worked metals, characterized by the appearance of new strain-free grains, growing at the expense of the cold worked grains until ultimately the new crystals completely replace the cold worked structure. In metals like brass this process was observed long ago to take place simultaneously with the return of the mechanical properties to those characteristic of well annealed material. The above definition implicitly assumes that the matrix in which the new grains are growing is essentially still in the cold worked condition at the time it is absorbed by the new grains, i.e., that the energy stored in the metal during cold working is not greatly decreased by recovery, prior to recrystallization. Accordingly, the bulk of this energy is assumed to serve as the driving force for the process of recrystallization. Recently, a great deal of evidence accumulated, indicating that the traditional concept may be considerably in error. Suzuki' found that by far the largest portion of the stored energy of cold work in compressed polycrystalline copper is released in the early stages of annealing, well in advance of recrystallization. Thus, the new recrystallized grains are undoubtedly growing in a matrix which is, at least energetically, no longer in the cold worked condition, but has nearly returned to the annealed state. It is true that in Suzuki's experiments the major hardness changes due to annealing were observed to take place concurrently with the formation and growth of the new grains, but this process apparently involved the release of only a minor residual fraction of the stored energy of cold work. Confirming in this respect the views of Wood," several recent investigations by various techniques lead to the conclusion that the grains of many, if not all, metals in the cold worked condition consist of small, slightly disoriented "crystallites" or "sub-grains".* (After appreciable deformation at room temperature, the subgrain size in copper appears to be about 7.104 cm and in high purity aluminum about 2.10-4 cm.) Recent investigations which demonstrated this phenomenon most convincingly are those of Heidenreich8 with hammered high purity aluminum, of P. B. Hirsch and collaborators7,8 with cold worked polycrystalline aluminum, copper, nickel, iron, gold, etc., and of Warren and Averbach9 with a rolled copper plus 2 pct Si single crystal. In addition to the existence of slightly disoriented sub-grains, the cumulative evidence from these investigations also shows that in the cold worked condition the subgrains themselves are severely strained. With regard to the early stages of annealing, Heiden-reich's results indicate that within the subarains of hammered high purity aluminum the strain gradually disappears, without discernible migration of the subboundaries. This recovery process presumably accounts for the major portion of the energy release

Jan 1, 1953

By R. S. Busk

Niels Engel (University of Alabama, University, Ala.)— In this paper it was pointed out that the electron-gas and energy-band theory accounts for the fact that the lattice parameters exhibit a sudden change when the electron concentration (number of bonding electrons per atom) exceeds a certain number around two. This statement is said to support and prove the electron-gas theory. But this theory is not able to account for a series of experimental data. Also several expectations, deduced from this theory, are not found to exist. In Figs. 6 and 7 the energy bands of the second and third periods are given as they must be assumed in order to account for the electrical properties of the elements in these periods. In Figs. 6 and 7 the electron-gas and energy-band theory is compared with the electron-oscillator hypothesis in accounting for the properties of the elements in the second and third periods. Fig. 6 shows the second period, The energy-bands are overlapping and separated to be in agreement with the electrical conductivity of the elements. The oscillator hypothesis explains conductivity due to electron vacancies. In graphite there is a closed s-shell in every other atom and two vacancies in the others. Conductivity is therefore only maintained by migration of s-electrons in graphite. In boron there are no s-electrons. The diatomic molecules of nitrogen and oxygen and the paramagnetism of oxygen can be accounted for by a similar behavior as the s-electrons of the bonding electrons. But this explanation will deviate too much for the purpose of this discussion. Fig. 7 shows the third period. In the energy-band picture about two s-electrons are assumed in magnesium and aluminum, but only one s-electron is assumed in silicon. The diamond lattice is assumed to be controlled by a sp3 hybrid. However the electron distribution develops ideally according to the oscillator hypothesis. Only sodium, magnesium, and aluminum exhibit electron vacancies and conductivity. To account for the insulator properties in Si, P, and S in the third period it must be assumed that the four last added p-electrons must be taken up in bands containing only one electron per band.' (Compare the electron band picture in Hume-Rothery.' Hume-Rothery does not consider the insulator properties of the nonmetals.) In the second period already the first p-electron must have entered a single electron band. Based on the energy-band picture in Figs. 6 and 7, the following questions must be asked: 1—Is it consistent with the energy-band idea that electrons of the same kind (p-electrons) can be divided into separated bands? 2—Is it consistent with the energy band idea that single electron bands can exist? 3—Why are the first two p-electrons (in boron and diamond) separated into two single electron bands in the second period, but overlapping in the third period (aluminum)? 4—Why are s-electrons and d-electrons taken up in continuous overlapping bands, while p-electrons are divided into single electron bands? 5—Why do the peaks and valleys (y and w and further x and z) of the energy band below four electrons per atom not show up in the electrical conductivity of alloys? For example consider the Li-Mg system or the alloys between Mg and three electron metals where the mentioned discontinuity in the lattice parameter is found. 6—Why does the beginning of the p-electron band (x) not show up in the lattice constants similar to the filling up of the s-electron band (z) ? In magnesium alloys the electron-gas theory postulates the first Brillouin zone to be filled at about two electrons per atom. This is claimed to explain the sudden change in lattice spacing and c/a values of several magnesium alloys when the electron concentration exceeds a few percentage points over two electrans per atom. This was emphasized in the paper by Busk. If the electron-gas energy-band theory is correct a sudden change in electrical conductivity and possibly other properties .should be expected when the same electron-concentration or temperature is exceeded. A sudden change in lattice spacing or other properties should also be expected when the filling degree is such that p-electrons are introduced into the p-band, for example at x in Figs. 6 and 7. Such phenomena are at found by experiment. and If the number of electrons should vary with the energy level depending on the average number of bonding electrons per atom, the electrical conductivity should be expected to vary in accordance with the energy band layout (Figs. 6 and 7) caused by different numbers of conducting electrons at different filling up degrees. Nothing indicating such a behavior is observed. In addition to these discrepancies between the electron-gas and energy-band theory and measured data, the theory violates the principles developed along with the Bohr theory of atomic structure. According to these principles a filled shell is saturated and therefore unable to form bonds. Therefore two S-electrons per atom should form a closed or saturated shell, which has been pointed out as accounting for the inability of helium to form bonds. Beryllium, magnesium, or calcium atoms with two s-electrons should be expected to form inert atoms with properties almost like the helium atoms. Several other inconsistencies and disagreements with measured data of the energy-band theory can be mentioned. Some of these are discussed with reference to other papers. 8 Because the electron-gas and energy-band theory seems to fail on several points, I have developed another theory which can account for all the phenomena the electron-gas theory is able to account for. This new theory is further able to account for things which are impossible to explain by the electron-gas theory at the present state.

Jan 1, 1953

By W. P. Sykes

TUNGSTEN serves mankind in two major roles. The first of these is represented by the tungsten filament of the incandescent electric lamp, a common article of commerce. In the field of hard alloys it plays its second substantial part. A fortunate combination of physical properties in this metal ac- counts for its efficient service as a source of illumination. Tungsten melts at about 3400°C, has a relatively low vapor pressure and at the same time sufficient strength, both hot and cold, to serve satisfactorily as filaments, which may range in diameter from 0.060 to 0.0005 in. In the early days of the incandescent lamp, the pioneers realized the importance of using a substance of high melting point for the source of light. The metals osmium (mp approx. 2700°C) and tantalum (mp approx. 2850°C) were both employed to some extent. Tantalum actually attained some commercial importance in this field because it could be drawn into small wires of appreciable length. DUCTILE TUNGSTEN WIRE Before the year 1908, tungsten was considered a nonductile metal, since no one had succeeded in overcoming the brittleness so typical of the unworked metal at room temperature. The methods employed today in producing ductile tungsten wire were developed over a period of years. The process was largely determined by the exceedingly high temperature required to melt this metal. Even today the difficulties involved in producing an appreciable quantity of pure

Jan 1, 1953

By D. S. Eppelsheimer, D. N. Williams

The compression texture of iodide titanium is determined and found to consist of a [0001] texture rotated 15° to 30° from the axis of compression. As the amount of reduction increases, the angle of rotation decreases. The 0001 rotation showed a slight preference for a <1010> rotation axis. RECENT investigation of the cold rolled texture of titanium&apos; has shown this metal to exhibit a new type of rolling texture. This texture can best be described as a (0001) [10i0] with the 0001 planes rotated approximately 30" to the transverse direction around a <10i0> rotation axis. Rather good results in explaining the cold rolled texture have been obtained by other workers&apos; by examination of the tension and compression textures. No information was found giving the tension texture of titanium. Generally the tension texture of a hexagonal close-packed metal is identical with its wire texture. The drawn texture of titanium has been investigatedh nd has been found to be predominately [10?0]. Since this is the common tension texture of hexagonal metals of low c/a ratio, the explanation of the difference between the rolling texture of titanium and the rolling texture of other hexagonal metals is not indicated by examination of the tension texture. Therefore, the compression texture of titanium should be particularly important in the explanation of the unusual transverse rotation of the 0001 planes found in the cold rolled texture. The compression texture of titanium was examined by Yen.",&apos; His results showed titanium to exhibit the usual [0001] texture up to 85 pct reduction. At higher reduction a double texture appeared in which the 0001 planes were rotated from 10" to 30" from the plane of compression. This change in the compression texture seemed unusual since the tendency for hexagonal close-packed metals is to approach the [0001] texture as the idea compression texture. Mechanical twinning generally occurs over a considerable range of reductions beginning at a rather low reduction. The samples used by Yen in his investigations were prepared by two methods. Compression in a testing machine was used up to a reduction of 85 pct. Compression by compression rolling was used at higher reductions. Since the change in texture occurred at the same reduction as the change in the method of compression, a connection between the two seemed likely. To check this possibility and to locate the position of the change in texture definitely, if it was found to exist, the compression texture of titanium was re-examined. An iodide titanium crystal bar (99.9 pct Ti) produced by the New Jersey Zinc Co. and donated by the Titanium Alloy Manufacturing Div. of the National Lead Co. was used in this investigation. Procedure The investigation of the compression texture was carried out in three steps; compression, specimen

Jan 1, 1953

By William H. Hartwig

A paper by Rose1 has called attention to some of the problems of wetting-liquid relative permeability measurement. The premises and conclusions set forth by Rose, namely the applicability of the Hassler scheme of measurement, will be accepted. In addition, it will be concluded that certain electrical analog circuits can be used as a pattern for consideration of possible hydraulic systems of measurements. NEW SCHEME OF MEASUREMENT The object of this note is to propose a new scheme of wetting liquid relative permeability measurement. It is significantly different from those heretofore described, nonetheless it is based on Hassler concepts. The scheme is illustrated in Fig. 1 in terms of the corresponding electric circuit analog. It may be designated descriptively as the "comparison" method of wetting-liquid relative permeability measurement. In this circuit, R, represents the resistance of the core sample which is being studied for relative permeability characteristics, R represents a "standard" resistance, R represents the combined series resistance of the barrier pads, R R2 represent the combined series resistance of barrier pads in the manometer circuit, C, C represent the capacitance of the manometers, E is a constant voltage source, S is the switch or stopcock. The following conditions are imposed upon .the network: Rb » R, and R, R,» R, R, » R., and the condensers C, and C,

Jan 1, 1953

By P. R. Sperry, P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the inside texture of highly rolled aluminum and copper strips may be approximately described by four equivalent ideal orientations near (123) [121]. If rolled in reversed passes, the surface texture of copper is also near (123) [121], that of aluminum is (100) [011]. The inside texture of highly rolled brass is (110) [112]. The surface texture is the same, if rolled in reversed passes. The surface texture of all three metals is related to the inside texture, but asymmetrical, if rolled without reversal between passes. MANY previous investigations dealing with the subject of the present work were reviewed by Wassermann.1 Barrett,2 Brick,3 and Richards.&apos; The recent introduction of quantitative methods for pole figure determination by Decker, Asp, and Harker,5 Schulz5 and others made it possible to reinvestigate some of the finer points which the earlier more qualitative photographic methods left undecided. The rolling textures of silver and of 70-30 cartridge brass have been quite consistently characterized by the ideal orientation of (110) parallel to the plane of rolling and [112] parallel to the rolling direction. On the other hand, it has been recognized by several investigators that certain other face-centered cubic metals, such as copper and aluminum, developed rolling textures rather different from that of brass. These textures have been variously described by the following ideal orientations, singly or in combinations with each other: (110 [112]: (112) [111]; (135) [335]; (135) [211], etc. The discrepancies usually have been attributed to the lack of sharpness in the textures and to the attendant difficulty of associating "ideal orientations" with pole figures showing great scatter of orientations. It seemed desirable to investigate by the new quantitative methods to what extent the apparent lack of sharpness may have been brought about by the qualitative methods used previously, rather than by the textures themselves, and to decide, if possible. between the various ideal orientations which have been proposed. Another problem, not satisfactorily settled by earlier investigations. concerns surface textures in rolled metals. For instance, in rolled aluminum the surface texture in some cases appeared to be similar to the texture inside the sheet, whereas in other cases it was reported to be entirely different.&apos; The conditions under which such differences may have arisen, and the possibility of the occurrence of different surface textures in other face-centered cubic metals do not appear to have been examined in detail. The present work was undertaken to investigate the above questions. Some of the results obtained have been described- riefly. Experimental Procedure Specimen Preparation: In the present investigation 2s aluminum, electrolytic tough-pitch copper, and commercial 70-30 brass were used. These materials were available in the form of cold-drawn rods. 1 in. diam for tough-pitch copper and commercial 70-30 brass and 11/2 in. diam for 2s aluminum. The cold-drawn bars were alternately annealed and rolled 30 pct lengthwise in several cycles until a penultimate thickness of 0.500 in. was reached. The intermediate and the penultimate anneals were carried out for 30 min at 380°C with 2s aluminum, and for 30 min at 550°C with 70-30 brass. For tough-pitch copper, the intermediate anneals were 30 min

Jan 1, 1953

By E. E. Donath

Application of the coal hydrogenation process for the production of chemicals is described. It has been estimated that a plant to produce 31,090 bbl per day of chemicals and fuels would cost $326,- 000,000. These products would consist of 6.1 pct by weight tar acids, 50.8 pct aroma tics, 16.4 pct LPG, and 26.7 pct gasoline. THE coal hydrogenation process is well known as a means for the production of liquid fuels from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aro-matics and of tar acids and tar bases. The relative amounts of heavy and middle oil—boiling above and below, e.g., 325°C—can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.&apos; Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catchpot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1953

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the syn-clines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no re-handling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor&apos;s bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1953

By M. Cohen, D. Caplan

The scaling characteristics of three Fe-Cr alloys have been investigated by determining their weight gain vs. time curves at 1600° to 2000° F. The scales formed thereby have been examined using the techniques of X-ray diffraction and spectrographic and metal-lographic analyses in an attempt to explain the discontinuities in the curves and to elucidate the mechanism of scaling. DESPITE the considerable number of investigations that have been carried out on heat resistant alloys, the characteristics of the scales formed at high temperatures are not fully known. The research reported here was undertaken in an attempt to ascertain the mechanism of scaling of the stainless steels. Scaling experiments were carried out first, the weight increase of the specimens being followed continuously with time. It was observed that, as well as showing the expected decrease in oxidation rate with time, the oxidation curves showed breaks corresponding to intermediate periods of accelerated oxidation, after which protectiveness again increased. This phenomenon was observed with austenitic stainless steels (types 302, 309, and 330) and with Fe-Cr alloys (types 410, 430, and 446), but only the latter are treated in this report. An examination of the scales was made using the techniques of X-ray diffraction and spectrographic and metallographic analyses in an attempt to obtain a correlation between the nature of the scales and the oxidation curves. A search through the literature revealed only a very few previous reports of such periods of accelerated oxidation. Dunn&apos; found breaks in the oxidation-time curves of some Cu-Si alloys but saw no rational explanation of the phenomenon. Heindlhofer and Larsen2 attributed a discontinuity in the weight gain-time curve of iron at 1290°F to the formation of blisters, the subsequent cracking of which exposed an unprotected surface and permitted rapid oxidation until a new protective scale had been reestablished. They advanced no explanation, however, for what they termed the peculiar behavior of a 27 pct Fe-Cr alloy at 2000°F which gained weight very rapidly in between two periods of very slow weight gain. Portevin, Pretet, and Jolivet3 in describing breaks in the weight gain-time curves of Fe-A1 alloys suggested that they might be associated with the occurrence of localized and deeply oxidized areas on the specimens. Bandel4 in a general discussion of oxidation curves of heat resistant alloys considered that the discontinuities were due to a local disruption of the protective layer by the growth of iron-rich oxides. Day and Smith" in their report on the scaling of a large number of iron alloys noted but did not explain occasional relatively rapid changes in oxidation rate at higher temperatures. Chevenard and Wache6 found breaks, often two per specimen, in the oxidation curves of an 18-8 type alloy. They suggested that the cause might be a depletion in chromium of the surface layer of metal due to its selective oxidation, the resultant high concentration of iron and nickel in the scale leading to a poorly protective scale. McCullough, Fontana, and Beck&apos; explained the breaks in the oxidation curves of types 304, 430, and 410 alloys as due to mechanical ruptures. Experimental Work Table I lists the chemical compositions of the materials used. Cylindrical specimens 1/4 in. in diam and 11/2 in. long were machined from cold rolled % in. rod. After a fine finish cut with a sharp tool, the specimens were abraded while still mounted on the lathe with Nos. 2, 1, 0, and 00 metallographic grade emery papers. A 3/64 in. hole was drilled at a distance of 1/8 in. from one end to permit suspension in the furnace. Specimen Nos. 1, 2, and 3 were tested with this surface preparation. All others, after being similarly prepared, were electropolished in a perchloric-acetic electrolyte, electrical contact being made by pressing a tapered platinum hook into the drilled hole. The specimens were then washed in hot water, rinsed with distilled water, rinsed with methanol, dried at 120°F, and weighed. Thereafter,

Jan 1, 1953

By R. E. Bish

IN an effort to distinguish experimentally between the radically different limits of two-liquid im-miscibility reported for the Cu-Pb system by Borne-inann and Wagenmann and by Briesemeister (see Fig. I), it was found that the high temperature homogeneous liquid containing between 41 and 93 pct Pb could not be frozen without separation into two liquids with the fastest cooling technique that could be devised. Thus, the two-phase state could not be distinguished with certainty from the one-phase state by the examination of quenched samples. To overcome this obstacle the following method for detecting the presence of an interface between two immiscible conducting liquids at temperature was developed. Measurements made by the new method substantiate the Briesemeister diagram in its general form. The method consists essentially in the measure-

Jan 1, 1953

By Orville R. Lyons

DISCUSSION Judson S. Hubbard (The Humphreys Investment Co., Denver)—In this very interesting paper several brief references are made to the Humphreys spiral, a device used for cleaning fine coal. In Table I, Plants 76 and 77, data are given on spiral performance treating Raton and Trinidad coal. The fine coal, as fed to the spiral in these instances, is actually a table middling, hence the more easily treated material was previously removed and a large number of particles were present which were difficult to clean. Mr. W. M. Bertholf of the Colorado Fuel and Iron Co. presented a paper in February, 1946, Cleaning Table Middlings from a Coal Washery with the Humphreys Spiral Concentrator, from which I quote: "In considering the results of our tests it should be noted that the feed was our table middling, and that any real separation is a &apos;moral victory&apos; as there is little material that could properly be called coal and practically no heavy rock, the consequences being that previous attempts to clean the middling have not at all been successful." Referring again to Table I, Plants 72, 73, 74, and 75, these data were obtained by Yancey and Geer and others and presented at the February 1950 Meeting, AIME, in a paper entitled Laboratory Performance Tests of the Humphreys Spiral as a Cleaner of Fine Coal. Results shown for those tests involve all particles from 8 mesh through the colloids, which admittedly is not an ideal situation for spiral feed if much refuse is contained in the —80 mesh or —100 mesh size range. As an illustration of the effect of treating too broad a size range, let us consider Plant No. 75, Kentucky No. 9 seam. Spiral feed was 8 mesh x 0. Now had this been 8x100 mesh the percentage of misplaced material would have been 8.0 pct instead of the reported 15.26 pct. Similar comparisons can be made on the other data presented with respect to the spiral. Other types of equipment show a similar trend in that whenever too fine a size is treated in a given unit process the percentage of misplaced material increases. Since the spiral is working near the finer end of the size range, it will sometimes be advantageous to treat the entire range of —8 mesh material rather than to deslime and make a fair showing on, say, the +80 or + I00 mesh. Desliming is subsequently done in any case in the dewatering or thickening operation. Results obtained by spiraling any given coal depend on factors too numerous and complex to discuss here, but there are strong indications that proper preparation of feed to the spiral can improve results obtained on some of the raw coals tested. This is clearly pointed out at the end of the aforementioned paper by Yancey and Geer. "The spiral is an extremely simple device which involves no moving parts and is constructed almost entirely of unmachined castings. Since it is such an uncomplicated mechanism, operation is simple and virtually foolproof. These characteristics, which go far toward insuring low cost operation, are attractive attributes in any coal cleaning unit." Certain equipment used in conjunction with the spiral has resulted in a decrease in the percentage of misplaced material, notably in actual practice the launder screen which is used to remove objectionable high ash fines from a spiral-washed coal product. Private correspondence with the U. S. Bureau of Mines has intimated that an additional yield of coal is possible by flotation of the spiral middling. Possible future improvements and developments may result from other methods now under consideration. Finally, some compromise must be made between the best metallurgical performance and the best practical or economical results. Mr. Lyons emphasizes in his summary this objective of overall economy in selection of equipment. G. B. Walker (American Cyanamid Co., Stamford, Conn.)—I had the pleasure of reviewing the draft of this paper and my curiosity was aroused by the data given for Tromp plants, in that all of the examples shown appeared to be 2-product separations, whereas all the Tromp plants with which I am familiar have been 3-product units. The data given for plants No. 101 and 102 appear to be taken from Tromp&apos;s brochure on his process and represent the results obtained at the Dominale plant in Holland which was operated for many years by Mr. Tromp. The plant, which was designed to treat 58 tons per hr, was sampled while treating 35 tons per hr of 3Y4x-in. coal. Example 101 appears to conform to what would result if the middling product were calculated into the refuse product, while Example 102 represents the calculation of the middling into the coal product. It is believed that Examples 103 and 104 represent the operation of the Willem-Sophie Mine in Holland recalculated on the same basis. In checking the English examples given by numbers 14, 15, 16, and 17, the same procedure seems to have been followed. These results have, apparently, been taken from an article in Colliery Engineering in August 1941, describing the initial operation of the Williamthorpe Colliery of the Hardwick Colliery Co. Two vessels are employed in this plant, one to treat soft coal and one to treat hard coal. Example No. 14 presents the results that could be obtained from the soft coal bath if the middling were calculated into the refuse, and Example 15 the results when the middling is calculated into the coal. Examples 16 and 17 represent the same expedient in the case of the hard coal bath. Of interest to this discussion is the fact that during the past year the Simon-Carves Engineering Co. in England has installed in the Williamthorpe plant their new "Sim-Car" medium cleaning system which is based on magnetic extraction and control and which is licensed under the Heavy-Media Separation Processes patents by the American Zinc, Lead and Smelting Co. This system has been described in the December 1951, issue of Colliery Engineering. It is reported that since the Williamthorpe Colliery was changed from the Tromp system of medium cleaning to the Magneto-Motive method of medium control the opera-

Jan 1, 1953

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota&apos;s production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953