Search Documents

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

Jan 1, 1949

By Horace R. Graham

CHEMICAL nitrogen and the "nitrates" of commercial significance are derived mainly from three basic sources: (1) the natural deposits in the form of nitrate-bearing earth and clay, which, being largely water-soluble, can exist only in the most arid portions of the earth; (2) coal, which yields not only nitrogen but also the additional by-product hydrogen required for the synthesis of ammonia and its compounds; (3) the atmospheric air, which contains 75.5 pct by weight of pure nitrogen gas. NATURAL NITRATE DEPOSITS Occurrence Although natural nitrate deposits consisting principally of the salts of sodium and potassium have been reported in Egypt, South Africa, Mexico, Argentina, Colombia, Peru and the USA, the only known natural nitrate resources of commercial importance are the vast deposits found in the Atacama, Tarapaca and Antofagasta regions of northern Chile, lying in a narrow strip 10 to 50 miles wide and roughly 450 miles long, between latitudes [19O] and [26OS]. In addition to yielding nitrates of sodium and potassium, these deposits are the source of the major portion of the world's supply of iodine. The nitrate-bearing ores known in Chile as caliche are variable in composition and may contain from 5 to 30 pct each of nitrate, chloride and sulphate. While the deposits are present chiefly in the form of the sodium salt, potassium, magnesium and calcium also occur in percent- ages from 0.1 to 5; usually as double salts with sulphate, which are but slightly soluble in nitrate leach solutions. These double salts are bloedite(Na2S04.MgS04.4H,0), glauberite (Na2S04.CaS04), polyhalite (K2SO4.- MgS04.2CaS04.2H20). Some deposits contain up to30 pct of their ni-

Jan 1, 1949

By L. D. Jaffe, D. C. Buffum

The importance of temper brittleness in alloy steels has long been realized in Europe. In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. Interpretation of Previous Data For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.' One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 45w550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness. If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2J found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.'-= The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture. If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1949

By George D. Roberts

Civil engineers are primarily interested in maximum core recovery. This is even more important in foundation work than in mining investigations where sludge samples are of some value. The soft materials, such as clay, gouge, or partially decomposed seams that are most readily ground up or washed away, are the materials that usually have the greatest influence on foundation and leakage conditions. Undisturbed samples of such materials should be obtained for detailed geological examination and laboratory tests. Therefore the attainable goal of sampling in connection with foundation investigations is the recovery of 99.9 pot of undisturbed core. Factors Causing Core Losses The principal factors contributing to core losses are: (1) coring badly fractured or very soft material; (2) Use of improperly designed coring equipment, including the use of bits of too small a diameter; (3) lack of the proper training and attitude on the part of the drillers and pertinent technical information on the part of the supervising personnel. Little can be done about the character of the material being cored but the other two factors contributing to unsatisfactory performance can be corrected. Although the title of this Paper is the improvement and standardization of core barrels, it is believed that the drillers' shortcomings and the lack of pertinent technical literature are more detrimental to good core recovery than either of the other factors. Uses For Large Diameter Core Barrels It is well known that the use of larger diameter bits and core barrels generally produce better cores, particularly when sampling soft or broken material. The use of larger and larger bit diameters and the insistence on better core recovery is well demonstrated by the change in practices of the various districts of the Corps of Engineers. Today NX core is the smallest diameter commonly permitted for investi-gational work and the more active districts are using coring bits up to 6 in. in diameter, as well as 36 and 40-in. calyx rigs. The latter size has proved to be just as economical because it provides more room for ctured removal and cleanup operations. The use of large diameter cores to replace the driving and jacking methods of obtaining soil samples is also increasing. The 57/8-in. Denison sampler, developed by H. L. Johnson to obtain samples from soft formations, is one example. The principal uses for bits larger than NX are: sampling soils and semi-consolidated rock; sampling decomposed rock or rock with soft seams; sampling concrete; obtaining samples for laboratory tests; drilling drainage holes, and other miscellaneous work. Core Drilling Practices of Several Engineer Districts Little Rock District The writer was employed in the Little Rock District from 1938 until 1942. Prior

Jan 1, 1949

By John H. Melvin

The Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. Geology Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its unce-mented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1949

By P. R. Sperry, M. L. Holzworth, P. A. Beck

The basic work of Z. Jeffries 1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria had been added, Jeffries found that grain growth was inhibited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. such a a temperature" was later found by Gross-mann~3,14 in certain types of steel, while ~~i~ showed15 that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently, 20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases with the titanium content. That coarsening may occur, as a result of, certain heat treatments, even in low carboil rimmed sheet steel, was shown by Samuels. He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material. In this instance the identity of the inhibiting phase has not been determined. However, Tangerding found23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction. The carbide particles Can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air is followed between in hydrogen for 75 hr at the Same temperature, grain growth is more hibition usually the whole specimen is transformed into a single crystal (approx. 1.5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth hibition from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced rtain the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pet Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1949

By F. J. Williams

BARITE, naturally occurring barium sulphate, is the chief barium mineral that is produced commercially. Barite is also called "barytes," "heavy spar," sometimes "baryta" and, locally in Missouri, "tiff." Pure barite is white, opaque to transparent. It crystallizes in the orthorhombic system, frequently with twinning. Impurities cause a wide variation in color, commonly buff, gray and white with irregular reddish iron stains. Less frequently found are shades of yellow, green, blue, brown, and black. The rock is brittle and breaks with an uneven fracture, although specimens from some of the residual deposits, particularly in Missouri, appear to have a cleavage due to the separation of the different layers of deposition. The hardness varies from 2.5 to 3.5 on Mohs' scale and different localities are said to produce either "hard" or "soft" barite. This generally refers to the ease of grinding of the product. The specific gravity of pure barite is 4.5 and this will vary downward, depending on the impurities present. The mineral has a white streak and a pearly to vitreous or sometimes stony luster. Pure barite contains 65.7 pct BaO and 34.3 pct SO3. Witherite, native barium carbonate, is not mined in the United States at the present time although a number of occurrences have been reported. A small quantity of witherite has been removed from a mine at El Portal, California, but the area high in witherite was small and soon depleted. The bulk of the deposit is predominantly barite. Great Britain is the world source of witherite and small quantities are imported into the United States. DISTRIBUTION OF DEPOSITS Occurrence of barite is widespread; it has been reported on all the continents and in all the major countries of the world. Deposits vary from those containing millions of tons down to scattered rock fragments

Jan 1, 1949

EVERY English-speaking mining, engineer or geologist knows that some terms used by his profession are not rigid but vary regionally; for example: what is called a vein by some, is called a lode by others and is known as a reef to their Australian colleagues. There are parallels in, the German language. Since, in addition, the meaning of some words may change considerably in 450 years-and other words may disappear completely-and not only the terminology but the concepts of a science are subject to drastic changes over such a long period of time, translating the Bergbüchlein posed some interesting problems. Old German texts and glossaries such as C. T. Delius' Anleitung zu der Bergbaukunst (1773), Minerophilus' Neues and Curieuses Bergwercks-Lexicon (1730), and H. Veith's Deutsches Bergwörterbuch (1871) proved useful sources of information when defini¬tions of obscure terms were needed. The task of translating was made even more challenging by the author's personality. As Ulrich Rülein von Kalbe was primarily a physician, his information must have been mostly secondhand. Since the nomenclature of the miners of Saxony, where he gathered his material on silver ores, undoubtedly varied from that of the German miners in Hungary, for instance, who probably supplied him with data on gold ores, it is not astonishing that he is not consistent in his use of some expressions. To give an example: there is every indication that Flöz and schwebender Gang (see footnote p. 21) are used interchangeably in spite of his occasional disapproval of such usage. It is obvious that he was an educated man with a questing and active mind and, although he apologizes-not wholly sincerely, one might suspect-for the simple

Jan 1, 1949

Jan 1, 1949

By M. R. Geer, H. F. Yancey

Although the use of dense suspensions for coal cleaning was pioneered in the United States with the Chance sand flotation process, and during the past year a pilot plant using a magnetite suspension has started operation in this country, the more recent developments in this field of coal cleaning have occurred principally in the Netherlands. During the thirties the Dutch developed the Barvoys process, in which a medium of barite and clay is employed, the Tromp process, which utilizes a magnetite suspension, and the Loess process, in which is used the air-borne earth or soil known as loess.1-3 All these processes are finding increasing use in European coal-cleaning practice. Now a fourth process, the cyclone cleaner, is under development by the Netherlands State Mines. A cyclone thickener for reclaiming and thickening the dense suspension is a novel feature of the Loess process. Through accident, the discovery was made that the cyclone could be utilized as a cleaning device for fine coal. When the cyclone thickener at the Maurits mine plugged, the overflow was found filled with clean coal free of refuse, and from this observation developed the concept of the cyclone as a coal cleaner. In June 1945 the cyclone cleaner was observed by one of the authors,' and in September 1945 it was described by Dries-sen6 in a paper presented in London before the Institute of Fuel. As the cyclone seemed to offer unusual promise as a means of extending heavy-medium cleaning to the finer sizes of coal that cannot readily be treated in existing heavy-medium processes, the Bureau of Mines, following Driessen's, presentation, launched an investigation of the cyclone as a coal cleaner. Added impetus was given to this study by the present increased interest in heavy-medium cleaning in this country. Object and Scope of Investigation Driessen's report, although comprehensive in many respects, did not include a detailed description of the cyclone cleaner, and contained almost no information on the influence of the various operating variables of the cyclone. It was necessary, therefore, to investigate the influence of the cyclone adjustments on its performance before studying the application of the cyclone to various coal-washing problems. The present report is confined entirely to these preliminary tests, designed to demonstrate the operating characteristics of the cyclone. The investigation has been in progress

Jan 1, 1949

By Oliver C. Ralston

THE two chemical compounds, natural sodium carbonate and sodium sulphate, in their anhydrous condition are dealt in as "soda ash and "salt cake”-names from an earlier day that are not as precise as the present accepted terminology. Once a large part of the sodium carbonate recovered was in the ash of seaweed, so it was logically called soda ash, and the corresponding potassium carbonate, once mainly recovered from wood ashes, was called potash. The term "salt cake" was applied to the sodium sulphate resulting from interaction of sodium chloride with sulphuric acid or sodium bisulphate, to form hydrogen chloride gas and an anhydrous cake of sodium sulphate. It was called "salt cake" and also "glassmaker's salt cake" because much of it was used in the production of glass. The two salts occur in nature in a variety of forms, but whereas an- hydrous sodium sulphate (thenardite) is fairly common, the anhydrous normal sodium carbonate, Na2CO3, is almost never found in nature. The monohydrate (thermonatrite), Na2CO3.2H2O, is seen occasionally, but it is never a major constituent in natural "soda" deposits. The high solubility of normal sodium carbonate is one reason for this. While both compounds occur widely in brines, the solid salts found in nature are usually trona (Na2CO3.NaHC03.2H2O) and thenardite (Na2SO4). The natural brines containing workable quantities of the two sodium salts are largely found in the arid and semiarid portions of the western United States and other countries. The classical discussion of the resources of these brines are those of Clarke,5 Chatard.4 Packard,19 Gale,11 and Wells.28 From North Dakota to California and from Arizona to the Canadian provinces of Alberta and Manitoba, saline lakes, dried-up lakes, playas, and similar land-locked depressions contain accumulations of saline matter. Sodium chloride is the predominant salt but some of the lakes contain predominantly either sodium carbonate or sodium sulphate. Often sodium carbonate

Jan 1, 1949

Jan 1, 1949

By Richard P. Schoemaker

Introduction In underground mining operations the effects of economic and mechanical factors on costs and profits can readily be appreciated and can perhaps be expressed in exact figures and percentages. Less apparent, but frequently more important, is the influence of physical stress. Stress causes failure of supports, collapse of openings, rockbursts, and other damage which directly affects the costs of maintenance, and also to a certain extent the accident rate. Stress can, however, if properly directed, be an aid to mining operations. The caving methods in metal mining and the long-wall method in coal mining are well-known examples. In large-scale mining operations it is almost impossible to neglect stress-control. A better understanding of the mechanism of rock pressure and the application of its principles to practical mining will inevitably lead to a reduction in operating costs. Many theories have been advanced to give the mining engineer a practical outline for stress-control but, although today most experts agree upon the principles of stress distribution around underground openings, there is still no generally accepted theory that explains all phenomena. The main reasons for this incomplete understanding of the problem are the lack of accurate knowledge of the physical properties of rocks under field conditions, and the great complexity of these conditions due to in-homogeneity of the rock, stratification, tectonic disturbances, and many other unknown factors. The research on the rock pressure problems has, however, yielded some valuable facts which, expressed in practical terms, and adapted to local conditions, may become a valuable aid for mining operations. The purpose of this paper is to give a review of the most important accomplishments of this research with respect to the stress phenomena around small underground openings, such as tunnels and shafts, so as to arrive at an outline of the problem as it stands today. Special emphasis is placed on a new theory by the German mining engineer, Rudolf Fenner, which has never before been published or discussed in English. The Pressure Dome Theory The formation of a dome-shaped space around underground openings is well known from field observations. When openings are made in rock under stress, the rock in the top of the openings will often fail, and caving will continue until the openings have assumed a dome-shaped form, after which equilibrium apparently is re-established. The oldest theory which attempted to explain the phenomenon is the "beam" theory, which postulates that the hanging wall consists of stratified measures that behave as independent beams with fixed ends and a uniformly distributed load. When failure of the beam occurs, inward shearing at the ends will cause the formation of a dome-shaped space. The pressure dome theory, which more or less evolved from the beam theory, merely

Jan 1, 1949

By G. L. Kothny

Developments of well-surveying instruments, coring .and core orientation, were in an advanced state when drilling for oil began—these developments actually originated with the mining industry.' Surveying of oil wells was not generally used in the United States until Alexander Anderson2 disclosed that the majority of wells drilled with rotary tools were crooked, with average horizontal drifts of about 516 ft. for holes 5000 ft. deep and about 793 ft. for holes 6000 ft. deep. This disclosure brought about the development of many additional instruments for surveying oil wells during the progress of drilling and after their completion. Surveying of boreholes, during the process of drilling at regular depth intervals, became a standard practice in the petroleum industry. Some producing states even established laws making check surveys mandatory, during drilling and under certain conditions also after completion. The surveying of boreholes also brought about changes and improvements in drilling practices. It provides information for the guidance of the hole while drilling, and for plotting the course as the work progresses, enabling the driller to take corrective measures immediately and with the least expense. The reasons for drilling straight holes are too well recognized to warrant any full discussion of them here. Straight holes are less costly to drill, because they reach the object on the shortest course. Table I shows the horizontal drift and loss in vertical depth for various angles of inclination. It is not surprising, therefore that many drilling contracts for oil wells today limit the drilling contractor to a maximum inclination off the vertical of 2° or 3O. In the mining industry the reasons for drilling straight holes are still more serious. A crooked hole may miss an ore body underground or provide incorrect information regarding an ore body. Types of Surveying Instruments The surveying instruments used in oil-well drilling may be classed in two types: I. Inclinometers, recording inclination only.

Jan 1, 1949

By J. J. Lander, L. H. Germer

Molybdenum and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved onlv limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150°C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1949

By M. B. Willey

The Louisiana Continental Shelf is a submarine area extending offshore as much as one hundred miles. The Gulf bottom in this region varies considerably in extent, profile and composition and consists largely of sedimentary deposits, predominantly those of the Mississippi River. It is very young in a geological sense. Up to the present time few major structures have been erected offshore in the Gulf and no comprehensive preliminary tests have been carried out. Results of pile driving tests are of little value as actual bearing capacities far exceed the dynamic resistance to driving as measured by conventional formulas. Soils encountered are, with few exceptions, cohesive and piling consequently develop their supporting power through surface friction. Because of the time required and relatively high costs, no complete load tests have been made. The results of those tests which have been made, and information obtained from pulling piling in one structure, indicate that design loadings could be considerably increased, and it is contended that comprehensive preliminary investigations including an actual load test, combined with borings and examination of materials encountered by competent soil experts, would effect economies in design far in excess of their cost. The Louisiana Continental Shelf—General The Louisiana . . . continental shelf is a submarine area which extends seaward for as great a distance as one hundred miles off the present shoreline. The Gulf bottom in this region is characterized by low slopes and its outer margin is outlined by the fifty fathom (300 ft.) contour. South of the margin of the shelf the slopes steepen abruptly in the continental slope zone and plunge into the deeps of the Gulf of Mexico.l The engineer who is called upon to design a structure on this shelf is concerned only with the uppermost portion to a depth generally not to exceed Ioo to 150 ft. This layer is very young in a geological sense, and it has the characteristics usually associated with infancy. A few of these are lack of strength, lack of uniformity, and high water content. It consists of the sedimentary deposits of the various rivers and streams entering the Gulf. These streams are all heavily burdened in quantities sufficient to fill the areas at their mouths, were it not for the fact that continual subsidence, equal or greater in amount and acting directly opposite, prevail over the sedimentary workings of the streams. This subsidence has been estimated by geologists to be at the rate of at least one foot per century. Influence of Mississippi River The Mississippi River, which has been the predominant factor in the formation of practically all the Louisiana continental shelf, is one of two rivers flowing into the Gulf that have been able to build protruding deltas. The Mississippi has done so because of its enormous size and load. It deposits sediments in amounts sufficient to replace and actually gain on the amount of subsidence.

Jan 1, 1949

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By C. P. Besse, G. W. Osborne

Drilling operations on the Gulf of Mexico continental shelf are following two general plans. The first plan placed all buildings. equipment, and materials on a large platform while the second copies Lake Maracaibo drilling methods by placing a minimum of equipment on the platform and using a floating drilling tender or drill barge anchored adjacent to the platform in an attempt to take maximum advantage of flotation in an effort to reduce costs. A complete power rig, mud pits, pipe racks, and small auxiliaries have been placed on the platform as shown in Figure 1, to assure proper handling of drilling operations under the most adverse weather. This has the economic advantages of eliminating the fabrication of a large structure, a material reduction of rigging up time on each structure. and elimination of delay time on equipment while quarters and equipment placed on the tender are being rigged up. These factors have certainly proved their economic value in drill barge operations in the Louisiana and Texas coastal area. Naturally the heart of such an operation is the anchorage. This anchorage, to permit taking advantage of maximum economies. must hold the ship in a relatively fixed position under the following weather conditions: (1) Winter northwesters (2) Southeasterly gales (3) Severe rain squalls In hurricane weather all operations must be suspended regardless of method of operation and the floating tender will, if possible, be moved to a protected location. However, in case of an emergency the floating tender should be prepared to swing with the wind and seas on a single anchor as there is considerable doubt that either ship or anchorage could withstand the severe strains imposed by fixed anchorage in hurricane weather. Northwesters are reported to have developed wind gust velocities as high as sixty miles per hour and steady winds of approximately forty-five miles per hour. Fortunately these winds do not travel a great distance over water before arriving at our location, and, while they can possibly develop seas approximately eight feet high, the waves are short, and if taken on the bow or stern of a ship 250 feet or more in length they should not present a difficult problem. On the other hand southeast gales having a long fetch and maximum steady wind velocities of approximately thirty miles per hour can possibly develop long swells approximately twelve feet in height. These should develop the most severe anchorage problem. To combat these waves any workable anchorage plan should permit maneuvering the ship in such a manner as to head the bow or the stern into the seas and still maintain contact with the structure. Rain squalls develop wind gust velocities as great as sixty miles per hour. However, they are local and the seas have not been a source of great trouble. To permit continuous operation the anchorage must be able to withstand these winds broadside to the ship as the wind direction often changes radically in a very sliort time. All of these weather conditions are dangerous to small craft, deck cargoes,

Jan 1, 1949