Search Documents

By G. H. Kesler, J. E. Oberele, C. E. Dryden, J. H. Oxley

Heat-transfer rates were measured in a model of a multifilament vapor-deposition bulb fo the preparation of high-purzty metals. Local transfer coefficients for heat transfer frow the filaments to the circuates process stream were determined as a functiol of gas flow rates and bulb, inlet, and filament, geowzetvies. These results a-e then convertted to n mass-t7,ansfer basis to provide a method of correlating vapor-deposition rates and to predict the performance of commercial urzits. The firm1 cor?,elating equation for mass transfer was found to be- wheve k, is the mass-transfer coefficient; D, is bze gas difficsivity : P is the system pressure; R is the gas constant; T is the gas temperature; Df, DB, and Di ave tlze diameters of the filament, bulb, and inlet, respectively; k is the gas conductivity; C, is the specific heat of the gas, M is the wzolecular zleight of the gas; Npr . N,,, NRe a7'e the Prandtl, Schmidt, and Reynolds numbem of the system, respectively; LB is the height of the bulb; and SB and Sf are the total suyiace area of the bulb and filaments, respectively. ONE of the more conventional methods of preparing very high-purity metals is the vapor deposition of the metal upon heated filaments. The reactions which can be employed in such a process generally fall into two classes: 1) Pyrolysis of a volatile metal compound. Generally because of their instabilities, metal iodides are used; however, other metal halides and hydrides have been employed. These processes are frequently carried out under vacuum conditions, and the filaments are maintained at high temperatures. 2) Hydrogen reduction of a volatile metal compound. A metal chloride is normally the preferred feed for these processes, but other halides are sometimes used under special conditions. These hydro- gen-reduction processes are usually operated at atmospheric pressure. Many of the current processes for the production of semiconductor materials are actually vapor-deposition processes. However, the vapor-deposition process itself is relatively old, and almost all metals can be prepared in a state of very high purity by the use of vapor-deposition techniques. Loonam has recently given an excellent review of the iodide process for metal deposition,' and Owen has started some detailed studies with a carbonyl system.' A more general treatment of all vapor-deposition processes has been outlined by Powell, Campbell, and Gonser.3 Despite the fact that vapor-deposition techniques have been employed since 1890, there is a surprising lack of fundamental information regarding the transport characteristics of even the simplest deposition system, the heated filament. The purpose of the investigation described in this paper was to extend some of the earlier data obtained at Battelle to predict deposition rates and the uniformity of deposition in large-diameter, multifilament deposition bulbs under forced convection conditions.4'5 A number of other investigators have already presented a simplified treatment of the deposition process under non-flow conditions, i.e., pure diffusion.6"9 To obtain information on the transport characteristics of a deposition bulb, a model of a typical plant deposition unit was constructed, and local heat-transfer coefficients from the filaments to a circulating air stream were determined under various conditions of air-flow rates and bulb, inlet, and filament geometries. These results were then converted to a mass-transfer basis, and consequently provided a method to correlate experimental vapor-deposition rates and to design commercial deposition units. EXPERIMENTAL WORK Description of Model. The apparatus which was used in this work was a scaled model of one type of deposition bulb. It was constructed of Lucite and was easily altered to give several combinations of diameter of bulb liner, inlet size and location, number of filaments, and outlet geometry. The model is shown in Figs. 1 and 2. The bulb shell was made octagonal for convenience in construction and observation, and the bulb liners were cylindrical. Air, introduced through one of several different jet inlets, was used as the test fluid in these model studies. Filaments for deposition of metal were simulated by metal rods 1/4-in. in diam. Two of the rods could be heated by passing electrical current through them ¦ while the remaining rods could not be heated. This procedure minimized the amount of heat which was

Jan 1, 1962

By W. Rostoker, R. P. Elliott, B. W. Levinger

Phase equilibria in the Ti-Mn-Mo system have been investigated in the composition range 100 to 60 pct Ti and in the temperature range 550 to 1150°C. Three out of ten isothermal sections are presented as well as seven vertical sections, projections of the beta space and the surface of incipient melting. A STUDY of the system Ti-Mn-Mo was undertaken as part of a program to aid in the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range 100 to 60 wt pct Ti (all compositions refer to weight percentages) and the temperature range 550" to 1150°C. A surface of incipient melting was constructed from measurements of a large number of alloys. In the binary system Ti-Mo,' the high temperature modification of titanium generally spoken of as the p phase is stabilized to successively lower temperatures with increasing alloy content. There are no known intermediate phases, and complete miscibility exists between body-centered cubic titanium and molybdenum. The u solid solution is limited to less than 0.8 pct Mo at temperatures between 885" and 600°C. An equilibrium diagram for the binary system Ti-Mn has been published.' Manganese behaves as a p stabilizer but undergoes a eutectoid transformation at about 20 pct Mn and 550°C to a plus an intermediate phase. The structure of this phase has been found to be isomorphous with the a phase FeCr." Accordingly, the phase is assigned the formula TiMn, although its actual location on the composition scale has not been determined and may well be not exactly at the equiatomic composition. In disagreement with ref. 2, the origin of the TiMn phase has been shown' to be a peritectoid transformation at a temperature between 900" and 1000°C. A second intermediate phase occurs at the atomic proportions TiMn,. The structure of this phase was originally established by Wallbaum" as having a hexagonal lattice (C 14 type, 12 atoms per unit cell) isomorphous with MgZn,. In this work, the structure determination was confirmed and lattice parameters determined to be: a = 4.815 kX, c - 7.901 kX. Because of the extensive range of the P phase, the ternary system was suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." During the course of the investigation, this method was found applicable only to the P/a+P boundaries but not to P/P+ compound boundaries. Metallographic methods were used alternatively for delineating these phase boundaries. Preparation and Treatment of Alloys Over 70 alloys were prepared for the study of this system. Ten gram alloy buttons were arc melted in a nonconsumable electrode furnace using inert atmosphere protection, and a water cooled copper crucible. The construction and operation of this type of melting unit has been described.' To insure complete solution of alloy additions, especially molybdenum, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" the ingots over. It was very difficult to obtain homogeneous melts in the region of less than 75 pct Ti because of the very high melting point of molybdenum and Ti-Mo master alloys and the comparatively low boiling point of manganese. Thus, the arc conditions for insuring complete solution of molybdenum were incompatible with the prevention of heavy losses of

Jan 1, 1955

By F. M., Waring

F. M. WARING,* Altoona, Pa.-The necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 12, 1918

By J. L. Christie, W. R. Webster, R. S. Pratt

Since the delivery of our paper on Some Comparative Properties of Tough-pitch and Phosphorized Copper,1 a new brand known as "oxygen-free high-conductivity copper" (brand OFHC) has become available to consumers. It was thought desirable to make a comparison between the properties of this material and those of the materials covered by our original paper and its discussion. Preliminary tests had indicated some notable differences. A billet of oxygen-free high-conductivity copper was taken from regular production. A chemical analysis of the particular billet was not made, but the producer of the material has given as typical the analysis shown in Table 1. The

Jan 1, 1933

By Richard Klimpel

In this paper various formulae are developed which can be used to estimate stream flow rates or weight ratios given information on the stream components. The type and level of experimental error present in the stream component analyses does have an important bearing on the numerical values (and reliability) of the weight ratios calculated by the various formulae. A simple but theoretically sound method is shown for selecting appropriate estimation formulae for any given engineering operation. The derived formulae are applied to sets of experimental classification data for illustration purposes.

Jan 1, 1980

By N. D. Policow, J. S. Orphanos

Dewatering fine clean coal fractions, -595µm (-28 mesh), represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the screen bowl centrifuge has offered an economical alternative to filtration/thermal dyer combinations. The performance of screen bowl centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Test comparisons with alternative methods show the screen bowl centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1984

By R. W. Gurry

When a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, yet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. Experimental Procedure Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;' it suffices to state here that the carburization lasted about I40 hr. at 760°C. (1760°F.) and 44 hr. at iiio°C. (2030°F.), these periods being long enough-—on the basis of the calculations presented later—to ensure that the specimen was about 99.9 per cent saturated at each temperature. The specimen was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully carburized specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 6, 1950

By Frederick Prime

In this supplementary list no titles to which an * is prefixed have been seen by the compiler; and he will be most thankfu1 to have any omissions or inaccuracies in the list sent to him to be published as a second supplement in the next volume of the Transactions. The author is indebted to Messrs. Robert Clarke, of Cincinnati; Thomas Macfarland, of Towanda; Professor F. W. Simonds, of Chapel Hill; and Professor J. J. Stevenson, of New York, for valuable assistance. Cedar Point IRON Company, Baltimore, July 31st, 1880. Alabama. Geological Survey of Alabama. Report of Progress for 1877 and 1878; by Eugene A. Smith, State Geologist. Montgomery, 1879. 8vo., 139 pp., and 4 maps.

Jan 1, 1880

By Richard R. Parizek, E. Scott Blair

Numerical modeling of ground water flow systems can be used to help analyze many practical problems encountered in the mining industry. Numerical models can be used to predict ground-water seepage rates into surface mines, shafts, and other large excavations; to predict water-level changes under adjacent properties; and to predict the effectiveness of various deep-well dewatering schemes. As with any model, the results from a numerical model are limited by the quality and quantity of data, and by the restrictions of any simplifying assumptions. A case study is presented that shows how a numerical model was used for engineering purposes to help analyze the hydrologic impact of a proposed open-pit mine by Predicting changes in the dewatering rate caused by the lateral growth and deepening of the mine and by predicting the effectiveness of various deep-well dewatering schemes.

Jan 1, 1982

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1937 and the reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Library, Student .Relations, Speakers for Local. Sections and Student Societies, and Mining and Metallurgy. To these reports members are referred for further details. Finances.-Income for the year was the largest since 1930, the figure being $189,394, an increase of $18,803 compared with income for 1936, exclusive of a special Rocky Mountain Fund appropriation of $2500 in that year for visits to western schools and Local Sections. Major items of increase were: $8,000 from current dues and arrears; $7,700 from advertising in MINING AND METALLURGY and the two periodical "Technologies"; and $4,800 from sales of TECHNICAL PUBLICATIONS (pamphlets) and TRANSACTIONS volumes for both current and former years. Initiation fees and clues from new members declined $2,300, principally because of the larger 'proportion of Junior Members to Members among the new enrollments. Junior Members pay no initiation fee and dues are $10 compared with $15 for Members.

Jan 1, 1938

By Dave H. Barnett, Brij M. Moudgil

The flotation technique as employed by Florida phosphate producing companies for the beneficiation of fine phosphate particles has been standardized over the years. Lower recoveries of coarse Phosphate rock by froth flotation technique, however, led to the development of new methods based on skin flotation of phosphate agglomerates. Recent developments of floating coarse rock in large flotation machines have not yet convinced the rock Producers of their higher separation efficiency. It is interesting to note that the selection of a particular machine is still bared on equipment preference by an individual company as well as proven performance of a particular machine for upgrading a specific material. Various techniques which have been developed to beneficiate the coarse phosphate rock have been discussed. Performance of the individual techniques is presented.

Jan 3, 1979

By R. W. Raymond

At the Liége meeting of the Iron and Steel Institute of Great Britain, in August, 1873, and also at the Vienna Convention of Mining and Metallurgical Engineers, at the end of August, and at the convention of German geologists, at Wiesbaden, in the first part

By K. J. Gill, P. Chiotti, J. T. Mason

Thermal, metallographic, and vapor pressure data were obtained to establish the pkase boundaries and the standard free energy, enthalpy, and entropy of formation for the compounds in the Y-Zn system. Three coinpounds with stoichiometric formulas of YZn, YZn2, and Y2Zn17 melt congruently at 1105", 1080°, and 890°C, respectively. Four compounds with stoiclziometric formulas of YZn3, YZn4, YZn5, and YZn,, undergo perztectic reactions at 905", 895", 870º, and 685ºC, respectively. Three eutec-tics exisl in this system with the .following eutectic temperatures and zinc contents in wtpct: 875ºC, 23.2 Zn; 1015ºC, 51 Zn; 865ºC, 82 Zn. The YZn, pkase undergoes an allotropic transformation. In the two phase YZn2 -YZn alloys the trans.formation gives a weak thermal arrest at 750°C, whereas in the two phase YZn2-YZn3 alloys no thermal arrest is observed and the transformation occurs over a temperature range below 750°C. At 500°C the free mzergies of formation per lnole vavy from —18,090 for YZn to —53,430 fov YZr11 and corresponding enthalpies vary from -24,050 to -92,080. The free energies and enthalpies per g atom as a function of composition show a maximum for the YZn2 phase; the 500°C values are -9580 and -13,180, vespectively. 1 HE only information found in the literature on Y-Zn alloys was the observation reported by Carlson, Schmidt. and speddingl that Y-20 wt pct Zn forms a low melting alloy. The alloy was produced by the bomb-reduction of YF3 and ZnF2 with calcium in an investigation of methods for producing yttrium metal. The solubility of yttrium in zinc has been determined by P. F. woerner2 and reported by Chiotti, Woerner, and Parry.3 In the temperature range 495" to 685°C the solubility may be represented by the relation In these equations N represents atom fraction of yttrium and T is the temperature in degrees Kelvin. The purpose of the present investigation was to establish the phase diagram for the Y-Zn system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure, and Ames Laboratory yttrium sponge. Arc-melted yttrium buttons contained the following impurities in parts per million: C-129, N-12, 0-307, Fe-209, Ni-126, Mg-13, Ca < 10, F-105, and Ti < 50. Some of the alloys containing 70 wt pct or more of Zn were prepared from yttrium containing 5000 ppm Ti as a major impurity. Tantalum containers were found to be suitable for all alloys studied and were used throughout the investigation. The pure metals, total weight about 30 g, were sealed in 1 in. diam tantalum crucibles by welding on preformed tantalum covers. A 1/8 in. diam tantalum tube was welded in the base of each crucible for use as a thermocouple well. Welding was done with a heli-arc in a glove box which was initially evacuated and filled with argon. The sealed crucibles were enclosed in stainless steel jackets and heated in an oscillating furnace at temperatures up to 1150°C. Homogeneous liquid alloys were obtained within a half hr at these temperatures except for alloys containing less than 20 pct zinc. The latter alloys were held at 1000º to 1100°C for 2 to 3 days in order to obtain equilibrium. After the initial equilibrations the tantalum crucibles containing the alloys were removed from the steel containers and used directly for differential thermal analyses. Further annealing heat treatments for alloys in which peritectic reactions were involved were carried out in the thermal analyses furnace. After thermal analyses the tantalum crucibles were opened and the alloys sectioned and polished for metallographic examination. In the following discussion alloys referred to as "quenched" were obtained by quenching the sealed stainless steel jacket containing the tantalum crucible and alloy in water. The differential thermal analyses apparatus used was a modified version of the one described in an earlier paper., The graphite crucible was replaced by an inconel crucible, the nickel standard and sampie container were separated by a 1/8 in. MgO plate, no getter was used, and provisions were made to

Jan 1, 1963

Discussion of the paper of COURTENAY DEKALB, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 331 to 337. HORACE V. WINCHELL, Minneapolis, Minn.-Mr. Dehalb summarizes the reasons which he believes are important for the revision of the mining laws, as follows: "1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous." We all appreciate the force of that suggestion. The idea of the old prospector who made rules and regulations in the early days, which were attempted to he incorporated, so far as possible, in the Mining Act of 1872, was that all of the veins in a certain district outcropped upon the surface, or approximately parallel to each other upon the surface, and maintained that parallelism beneath the surface. Therefore, it seemed perfectly proper and natural for each man to stake his claim upon an outcropping, and have the right to follow that vein in working downward, with the general expectation that his workings would always remain just as far away from those of his neighbor as the outcroppings upon the surface. This does not happen to be the case. Dr. Raymond has very ingeniously referred to the subject in one case, in words which read as follows: "If all mining properties presented this beautiful simplicity of structure (ideal location of ideal vein), and all mining locators exhibited a corresponding simplicity of purpose, the application of the law would be easy, but the naiveté of the statute fares badly between the freaks of nature and the tricks of man."

Jan 5, 1915

By E. T. Clymer

It has been the custom, from the earliest time, to grade pig-iron by the appearance of the fracture; and although, since the pneumatic and open-hearth methods of steel-making have come into existence, chemistry has been called to the assistance of the steelmaker in selecting material for his use, the consumers of forge- and more especially of foundry-iron, still rely almost entirely, as they did a hundred years ago, on the appearance of the fracture of the pig to guide them in the choice of iron. To this rule, however, each year sees more exceptions; and there are now many foundry-men

Jan 1, 1893

By C. W. Merrill

Minerals research by the U.S. Bureau of Mines embraces the mining and metallurgical problems of some 80 metals and nonmetals excluding the mineral fuels. It requires the energies and talents of about 1400 persons, almost half of whom are professionally trained in the physical sciences or engineering. Of approximately $13 million appropriated to the Bureau for minerals programs in Fiscal Year 1962, 76% has been allotted to technologic research and 24% to resources examination and appraisal. In addition, almost $2 million will be made available to the Bureau for minerals research from other Government sources and from private organizations that wish to utilize Bureau experience and capabilities in cooperative studies.

Jan 11, 1961

By G. C. Gester

With the exception of exploration geological work that is being prosecuted in various parts of the mainland of Arabia, the only new developments in Arabia during 1934 were on Bahrein Island, which is in the southwestern portion of the Persian Gulf, approximately 25 miles from the mainland of Arabia. Here the Standard Oil Co. of California, through its wholly owned subsidiary, The Bahrein Petroleum Co., Limited, has continued to carry on a systematic drilling campaign and has constructed camps, pipe line and marine loading facilities. During 1934 eight wells have been completed at depths ranging from 2058 to 2253 ft. These wells have shown average initial productions ranging from 1500 to 5000 bbl., with one, No. 15, estimated as being capable of flowing as much as 11,000 bbl. per day. The oil is asphaltic in character and has a gravity range of from 32&apos; to 34&apos; A.P.I. The locating of all new wells has followed a plan of orderly development, with the ultimate object of obtaining efficiency of operation and maximum production. The wells are taking a penetration of 200 to 250 ft. of the lower or so-called Main productive zone. The upper oil zone, which is cased off, includes 300 to 400 ft. of alternating limestones, clays and shales and carries a heavier oil under lower pressures. The Main zone is similar lithologically to the upper zone. Micro-fauna collected from cores have shown that the oil occurs in formations of lower Eocene and Cretaceous age. Development to date has not progressed sufficiently so that either the maximum thickness of the oil-bearing horizons or the limits of the field can be determined. Something over 10,000 acres has been proven to date. Among other developments leading toward the marketing of oil from Bahrein during 1934 was the construction of a marine loading terminal. This included the laying of over 3 miles of 12-in. submarine pipe line from the small island of Sitra out into the harbor, terminating in 50 ft. of water; also the laying of more than 10 miles of gathering lines from the producing area to the terminal. Three crude oil working tanks with floating roofs were erected on Sitra Island, having a capacity of 250,000 bbl. A pumping plant was provided having a capacity of 5700 bbl. of oil per hour. This is housed in a dustproof building, as rather severe

Jan 1, 1935

By Emmanuel Detournay, Charles Fairhurst

A method is proposed for computing (a possible solution of) the ground reaction curve, for use in tunnel support analysis, in cases where the initial stress field is not hydrostatic. Rock around a circular tunnel is assumed to behave as an elasto-plastic material with a Mohr-Coulomb yield envelope.

Jan 1, 1982