Search Documents

The Library of .the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days; except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may he what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 6, 1913

By A. G. Loomis

IT is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analysis1 of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acids1,2-for example, sodium tannate or gallate-and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shut-downs. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells.

Jan 1, 1940

For the first time, the attendance at the meetings of the Institute passed the thousand mark; as is shown by the following table: REGIS- AT BANQUET DID TOTAL TERED NOT REGISTER Men :..:... 703 76 806 Women 195 61 256 1062 The names of the members and guests who registered or attended the banquet but did not register are: A A. D. Beers C. A. Adams Hans Behr Thos. J. Adams Edgar G. Bell Lawrence Addicks Donald A. S. Bell H. T. Abrams W. de LeBenedict G. Aertsen G. B. Bertelli M. M. Albertson Charles P. Berkey James Aldrich Clinton Bernard D. C. Alexander, Jr. W. N. Best W. H. Alexander Robert M. Betts A. W. Allen Christopher H. Bierbaum F. D. Aller Paul Billingsley R. H. Allport R. A. Bingham F. C. Alsdorf R. M. Bird Capt. M. Altmayer John L. W. Birkinbine A.' W. Ambrose G. S. Bisey Henry M. Ami Charles W. Boise F. L. Antisell J. J. Blackmore R. S. Archer A. E. Blackwood Paul' Armitage Capt. C. K. Blatchly Andrew B. Armstrong E. L. Blossom Clifton T. Armstrong C. A. Bohn Ralph Arnold James M. Bonsall R. M. Atwater, Jr. E. E. Boon Joseph E. Aue Gail Borden A. M. Austin R. S. Botsford W. S. Ayres John M. Boutwell

Jan 4, 1919

By Edward H. Robie

THOUGH the final figures are not available as this is written, it seems certain that the Institute accounts will show $7000 to $8000 surplus for the year 1951. This is the first time this has happened since 1941. No money had to be taken from any of the Funds to bring about this happy condition. Furthermore, the amounts allowed for depreciation, bad debts, and inventory adjustment were more liberal than in the past. Income increased some $29,000 over 1950. Dues received from old members increased moderately, but dues from new members dropped off $2000 and from initiation fees quite severely-from $17,000 to $11,000. The number of new members did not come up to expectations and a change in procedure caused a delay in getting some of them on the rolls. A large number of the new members paid an installment of $5 on their initiation instead of the full $20. Junior Members, of course, pay no initiation fee. Brightest spot in the income picture was the increase in advertising income-from $103,000 in 1950 to $143,000 in 1951. All three of the journals shared in this, Mining being up $18,000; Metals, $9000; and Petroleum $13,000. Nonmember sales of the journals dropped off slightly, and sales of Transactions volumes more so from $35,000 in 1950 to $27,000 in 1951, with a further drop of $5000 accounted for by a change in accounting procedure. On the other hand, sales of other publications increased by $10,000.

Jan 1, 1952

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10 to May 10, 1914: Members ADAMS, HENRY H., JR., Merchant, Henry H. Adams & Co., and Colonial Iron Co., 149 Broadway, New York, N.Y. ADAMS, LELAND D., Mine Mgr., Supt., East Canada Smelting Co.,Weedon, Quebec, Canada. AGUILERA, EUGENIO, Chief Engr. Mining & Foresting Dept. of Santiago, Santiago de Cuba, Cuba. ALFORD, NEWELL GILDER; Min. Engr., Asst. Chief Engr., St. Bernard Mining Co,. Earlington, KY.

Jan 6, 1914

By B. B. A. Luzzat

ALUMINUM is today the most widely used of the nonferrous metals. The technical literature on the aluminum smelting process is, nevertheless, very meager, so that anyone interested in the subject cannot rely on more than a couple of dozen publications.' The patent literature is equally scarce; most patents refer to the production of alumina from aluminum-bearing ores, while not more than a few score significant patents deal with the electrolytic reduction of alumina, which is the real core of the aluminum smelting industry. The "reduction phase" is, from a technical and a scientific point of view, much more interesting than the "alumina phase", which, in effect, is only a combination of such well-known chemical operations as dissolving, precipitating, filtering, drying, and calcining. The electrolytic reduction of alumina, on the other hand, has features which do not appear in any other metal smelting operation. Some of them are of great technical and scientific interest even for those not directly engaged in the production of aluminum. The purpose of this paper is to describe in some detail the basic facts and developments of the reduction phase of aluminum smelting. Two Aspects of the Electrolytic Process The raw material for the reduction process is alumina (Al2O3) . Its purity in general runs as high as 99.50 pct or more. Small differences in the chemical composition generally do not affect the reduction process.* Of more importance are the physical prop- erties of the alumina, since they affect not only its rate of solution in the molten bath but also its heat insulating power.† In the following pages, un- less otherwise stated, it is assumed that a standard "Bayer" alumina is used. The reduction process, by which alumina is broken down into its components, may be roughly defined as its electrolysis in molten cryolite. The oxygen separates at the anode, and the aluminum at the cathode, which forms the bottom of the electrolytic cell. The electrolytic cell (or pot) where the process is carried out is a strongly reinforced steel box. The

Jan 1, 1951

By Theodore Swann

DURING recent years, there has been a material increase in the use of ferrophosphorus in the steel industry. It has been observed, when rolling sheets, that those made of Southern iron did not have to be rolled at as high a temperature as the others and, consequently, did not stick together. The reason was found to be the phosphorus content of Southern iron. It was therefore thought that an addition of phosphorus to sheet steel of other than Southern origin would give the same result as the use of Southern iron. At first, this addition was made by intro¬ducing phosphate rock in the blast furnace and reducing it together with the iron ore; but, because of the necessity for only small quantities of this grade of iron, the process was not satisfactory. The manufacture of ferrophosphorus was then introduced, so that additions might be made to the open-hearth furnace or ladle. Ferrophosphorus was first manufactured in the blast furnace. This method, however, can only economically produce a grade of product up to about 20 per cent. To produce a higher grade, it would be necessary to charge a larger proportion of phosphate-bearing material; and as the rate of absorption by the iron is low, there would be an increased loss of phosphorus oxides. This feature makes the production of a higher grade ferrophosphorus in the blast furnace uneconomical. The use of high-grade ferrophosphorus in the steel requires a smaller addition and involves, besides the economies in handling, an additional economy in transportation. The alloy with a higher percentage than 20 per cent. can be made only in the electric furnace. In the ordinary operation of the electric furnace in the production of ferrophosphorus, an alloy may be produced containing 26 per cent. phosphorus; this is the limit, for it does not seem possible to produce a higher phosphorus alloy even if large excesses of phosphatic materials are used. The reasons for the difficulty in raising this percentage of phosphorus are not known. The compounds Fe3P, containing 15.6 per cent., and Fe2P, containing 21.7 per cent. phosphorus, have been studied and it appears as if the alloy produced, containing percentages of

Jan 10, 1924

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939

By William Mikulas Lars Thomassen, Clair Upthegrove

Little work has been done in the field of the nickel-tin binary system. The complete diagram has been investigated on two occasions, but the results are in very poor agreement. The structure of a compound NiSn and the solubility of tin in nickel have been determined by X-ray methods. Several investigations have been made of the liquidus curve, and the compositions of the eutectics have been determined. A study of the literature, however, shows that there is no satisfactory agreement between the data presented in the various papers. The present investigation was undertaken in an attempt to determine the equilibrium conditions, and to correlate X-ray with metallographic data. The equilibrium diagram was determined by thermal and metallographic means, and the solubility of tin in nickel further investigated with X-rays. Powder diagrams were made of the intermetallic compounds, and three of the structures were partly determined. NO attempt was made to determine the range of homogeneity of the intermetallic compounds. Review of the Literature Vigorouxl prepared alloys of tin and nickel containing 74 and 92 per cent of tin. By treating these alloys with very dilute nitric acid or with sodium hydroxide he was able to separate residues, both of which analyzed 66.7 per cent tin. This corresponds to the compound NiSn and was reported as such. Guillet2 made the first investigation of the complete binary diagram Fig 1) The maximum point of the liquidus is at 43.5 per cent nickel. Several solid solution areas were found, and the compound NiSn was included on the strength of Vigoroux's work. The investigation was

Jan 1, 1937

By R. H. Terhune

THE enormous production of pig-iron, together with the many difficult and interesting problems with which its manufacture is fraught, 11as secured to this industry the exclusive attention of scientists with reference to the chemistry of iron, while some of the minor departments of its metallurgy have suffered neglect. Particularly is

By H. I. Aaronson, C. Wells

THIS is a preliminary report on a detailed metal- lographic investigation of the bainite reaction in a plain carbon hypoeutectoid steel. In view of the current interest in the bainite reaction and of the controversies which still exist about even the basic phenomenology of this mode of transformation, it was considered desirable to present a summary of the more important results obtained to date prior to the completion of this investigation. The steel used contained 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was homogenized for 48 hr at 1250°C. Individual specimens were then austenitized for 30 min at 1300°C and isothermally transformed for various times at temperatures above and within the bainite region, ranging from 775" through 500°C at intervals of 25°C. These specimens were carefully examined on a research metallograph; a few specimens of especial interest were also studied electron microscopically.' Bainite may be defined as the aggregate structure resulting from the precipitation of carbides from supersaturated ferrite which formed by nucleation and diffusion-limited growth. Two groups of experimental observations made during the present study provide support for this mechanism of the bainite reaction: 1—at 625°C, partial conversion of pro-eutectoid ferrite to bainite began after more than 99 pct of the austenite had decomposed and 2—the precipitation of bainitic carbides occurred only within the ferrite phase. The proeutectoid ferrite and the bainite reactions in the steel studied were found to be morphologically continuous. Following the classification scheme of Mehl and Dube,2 three principal morphologies of proeutectoid ferrite were identified in the temperature region (625" to 550°C) in which the two reactions blend—grain boundary allotriomorphs," * Grain boundary allotriomorphs are crystals which nucleate at and grow preferentially along matrix grain boundaries. Widmanstaetten side plates, and intragranular plates. Carbide precipitation converted these morphologies into their bainitic equivalents with increasing isothermal reaction time. Conversion took place more rapidly as the reaction temperature was reduced. The replacement of supersaturated ferrite by bainite, however, did not occur uniformly even within individual austenite grains and was noticeably incomplete at higher transformation temperatures, e.g., 625° to 575°C. The ferritic and bainitic forms of a given morphology thus were frequently found to coexist, often inextricably intermixed, in a given specimen. At 625" and 600°C, the conversion of ferrite to bainite was clearly seen to have occurred entirely by the nucleation of carbides at ferrite/ferrite boundaries, as shown in Fig. 1. The nature of the loci at which carbides formed at lower temperatures was often difficult to ascertain with a light microscope, although the alignment in rows of many of the carbides, illustrated in Fig. 2, suggested that nucleation had again occurred at grain boundaries or subboundaries within the ferrite. Application of the electron microscope confirmed this deduction for bainitic structures formed at these temperatures, as shown in Fig. 3. The dense black appearance of bainite formed at very low reaction temperatures in higher carbon steels3 indicates, however, that isolated lattice defects within ferrite crystals prob-

Jan 1, 1956

By R. Schuhmann

D. W. Fuerstenau (Associate Professor of Metallurgy, Dept. of Mineral Technology, University of California, Berkeley, Calif.) In his excellent paper, Dr. Schuhmann has proposed a mechanism for conlrninution which can be utilized to explain a number of phenomena which have been observed in the size reduction of solids. The difference between the product obtained from a ball mill and from a rod mill can readily be explained by Dr. Schuhmann's hypothesis. Consider that the size distribution of the product from each comminution event is given by y; - 100 (x/ki) (1) where Yi is the cumulative percent finer than size x, ki is the size modulus, and is the distribution modulus for the single comminution event. The total product from a cornminution operation will be the summation of the products from all of the individual cornrninution events. If the size moduli from the various comminution events range from kl to kn , the size distribution of the total product will be a straight line on a log-log plot only to a particle size equal to k ,. Considering 100 volurnes of feed, the value of y for x equal to kl is Riven by where y is the cumulative percent finer than size kj, z is the number of comminution events of kind i, and vi is the volume of each particle crushed. y=z1 qv1+z2 qv2 (k1/k2) +.............zn qvn (k1/kn) (3) F or particle sizes greater than k1 7 e. 6. x = k3, the value of y will be given by k3 A y = z1 qv1 + z2bv2 + Z3uV3 + zn zn qvn (k3/kn)(4) Only when x is equal to k, will y equal 100. 'Thus, the total product from a comminution operation will be a straight line on a log-log plot strictly up to a particle size equal to kl and above that size the line will curve so that y will equal 100 for the coarsest particle or k, (see Fig. 1). The actual shape of the size of distribution curve will depend upon the relative number of conmninution events of different kinds. In the case of ball milling, the ratio kn/kl may be pite large and there will be considerable deviation at the coarse sizes in a Schuhmann plot. kIowever, the grinding action in a rod mill is such that fine particles are protected from the rods by the coarse particles. Consequently, kn/kl will be quite small and the product from a rod mill will give a straight line Schuhmann plot almost to y equal 100%. In his paper, Dr. Schuhmann also has presented a very straightforward definition of grindability derived from the basic energy equation E = Ak-a (5) where E is the energy required to comminute a material to a size modulus of k and A is a constant. According to Dr. Schuhmann, the grindability of a material is the volume of material comminuted finer than unit size per unit of energy expended, this being 1/A. For comparison of grindabilities at any size two numbers are required, both = and 1/A, and anyone tabulating grindabilities should give both of these numbers. Concerning the experimental determination of grindabilities, if the material being comminuted possesses distinct cleavage, the energy re quired for comminution is given by E = Ak-(a-y) (6) where y is small number less than = . Because of cleavage, less energy will be required for comminution. To be certain that cleavage does not affect the gindability of the material being tested, it is suggested that the method used by Dr. Charles for determining grindability be used to ascertain if the deviation exponent y is zero or finite. R. Schuhmann, Jr. (Author's Reply) Dr. Fuerstenau's interesting comparison of rod milling and ball milling

Jan 1, 1961

By R. C. Ku, A. J. McEvily, T. L. Johnston

The microplastic response of a series ofas-quenched Fe-Ni-C martensites has been measured at 77°K. At strains less than JO'3 the flow stress is governed primarily by the transformation-induced dislocation structure of the martensite. Only at strains in excess of 10-3 is the influence of carbon manifested in the flow stress. At these macroscopic strains, typically 10-2, the solid-solution hardening is proportional to (wt pct C)1/3, and, in an alloy containing 0.39 wt pct C, amounts to 50 pct of the flow stress. THE technological significance of high-strength ferrous martensite has stimulated many investigations of its structure and properties. Although our knowledge of the characteristics of martensite has increased immensely, especially with the advent of high-resolution techniques, an understanding of the basic strengthening mechanism still remains elusive. The purpose of the present paper is to consider certain aspects of micro-plastic behavior of Fe-Ni-C martensite which we feel can help to resolve this important problem. Such alloys are particularly suitable for experimental investigation because their compositions can be adjusted to reduce the M, to a temperature low enough essentially to eliminate the diffusion of carbon in the freshly formed martensite.1 The mechanical properties in this condition are of interest inasmuch as they reflect a state that is free of the important but complicating influence of precipitation processes. In this virgin martensite the carbon is distributed as it was inherited from the parent austenite; i.e., it is present interstitially, and gives rise to tetragonality through strain-induced ordering.' In order to determine the source of strength of such alloys, Winchell and Cohen1 investigated the low-temperature macroscopic stress-strain behavior of a series of virgin martensites of increasing carbon content but of common M, temperature (-35°C). They found that the flow stress increased rapidly with carbon content up to 0.4 wt pct; beyond this point the flow stress increased at a much slower rate. It was concluded that martensite is inherently strong. To account quantitatively for the strength of virgin or as- quenched martensite in terms of the role of carbon, Winchell and cohen3 suggested that the carbon atoms, trapped in their original positions by the diffusionless martensite transformation, interfere with dislocation motion according to a model akin to that of Mott and Nabarro. 4 In this treatment, individual carbon atoms are considered to constitute centers of elastic strain and thereby generate an average stress resisting the motion of dislocations throughout the lattice. The additional stress necessary to move dislocations, over and above that necessary for motion in a carbon-free martensite, is given by where L is an effective length of dislocation capable of motion. L was assumed to be limited to the spacing between the twins that are an essential structural element of Fe-Ni-C martensites. They assumtd the spacing to be invariant and of the order of 100A. However, recent work5 has shown that L is variable and can be in excess of 1000Å, so that the assignment of an appropriate value of L is not straightforward. In contrast to the above conclusion that there is an intrinsically high resistance to plastic flow, it has been suggested by Polakowski6 that freshly quenched martensite is in fact "soft" in the sense that dislocations are initially free to move upon application of stress. The high indentation hardness and macroscopic yield stress of ferrous martensites are then a consequence of rapid strain hardening that depends upon carbon in solution. Consistent with this point of view are the results of Beau lieu and Dubé who measured the rate of recovery of internal friction as a function of aging (tempering) temperature in a freshly quenched steel containing 0.90 wt pct C, 0.37 wt pct Mn, 0.1 wt pct Cr, and 0.07 wt pct Ni. The kinetics were clearly consistent with the idea that many dislocations are unpinned in the as-quenched state and that during aging they become progressively pinned by carbon at a rate controlled by carbon diffusion in the body-centered martensite lattice. In order to provide a basis upon which to distinguish between the "hard" and "soft" interpretations indicated above, we have made studies of the initial stages of plastic deformation in Fe-Ni-C martensites similar to those'used by Winchell and Cohen. It will be shown that the results support the contention that dislocation segments in as-quenched material are indeed

Jan 1, 1967

By M. E. Wadsworth, A. E. Lewis, R. L. Braun

Experimental results obtained in laboratory leaching studies of primary copper sulfide ore in sulfuric acid systems pressurized with oxygen are interpreted by a computerized geometric model involving the movement of a reaction zone through the ore fragments. Physical properties of the ore, including size, shape, and mineral content, are considered. The leaching mechanism involves mixed kinetics and includes a surface reaction within a moving reaction zone plus pore diffusion of dissolved oxygen through the reacted portion of the ore fragment to the reaction zone. The results are applicable to conditions that would exist in nuclear solution mining or similar processes in which the ore is converted into rubble and then inundated by a leach solution adequately supplied with oxidants. Experimental results at 90°C are correlated with the model, which includes temperature-dependent parameters.

Jan 1, 1974

By R. T. O’Brien, J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and Ni (11) and Co (Ilj concentrations. Results have been discussed in terms of adsorption of Ni (11) and Co (11) cations and hydroxide precipitates. Possible relationships between the experimental results and the formation of lateritic nickel deposits have been discussed. The adsorption of metallic cations to the surface of silicate minerals is of significance in many industrial and natural processes. In an earlier publication,' the adsorption of Fe (111) to the quartz surface, a phenomenon of importance in flotation, was studied qualitatively using microelectrophoresis techniques. This paper reports the extension of this work to an investigation of the adsorption from aqueous solution of Co (11) and Ni (11) to the quartz surface. The adsorption of these metals was of interest for two reasons; firstly, the importance of such an adsorption process in the formation of nickel deposits by the lateritization of nickeliferous rocks, and secondly, the comparison of electrophoresis data for these metals, whose hydroxides precipitate in the pH range 7-8, with similar data for Fe (111) where the hydroxide first precipitates at pH 2.8. The development of laterites is essentially a near-surface geological process involving vertical and, in part, horizontal redistribution of elements derived from rock-forming minerals. This redistribution of elements leads to the formation of layers within the lateritic profile which are enriched in one or more of these elements and, depending on the nature of the original rocks, continued lateritization may give rise to iron ores, bauxites or nickeliferous laterites. The mechanisms discussed in this paper deal with the last mentioned type of deposit although the considered factors are applicable to laterites in general. Nickeliferous laterites are derived from basic and ultrabasic rocks containing ferro-magnesian silicates. These rocks may be partly or wholly converted to serpentinites. Besides their high Mg, Si and Fe contents, they also contain small amounts of Mn, Al, Cr, Ni, Co, Cu and Zn. The nickel content is usually near to 0.2-0.3%, but for economic use this must be increased during lateritization to over 1% and preferably over 2%. The zone of nickel enrichment is usually at some depth within the lateritic profile. Unpublished work by Mr. O'Brien on nickel-bearing laterites in eastern Australia indicated four visually different types of material which were separated from crushed samples under a stereo-microscope. Although chemical analyses indicated that all four types of fragments contained 2-4% nickel and smaller amounts of cobalt, X-ray diffraction and optical studies revealed only quartz, hematite and chromite as well as, in one of the types, a serpentine mineral. No distinct, nickeliferous minerals were detected. Furthermore, it was possible to extract some 60% of the nickel content of the laterites with cold 0.5N hydrochloric acid. It was therefore postulated that much of the contained nickel was present as amorphous, adsorbed material. In considering this fact, as well as the problem of the actual method of transfer and fixation of elements within the lateritic profile, it was further postulated that the transfer of these elements probably took place partly as solutions and partly as colloids and that the fixation of these was caused by adsorption and flocculation. The existence of nickel in solution in water draining from serpentinites has been confirmed by Smurov.2 Although we have no evidence for the transportation of nickel in the colloidal state, it is well accepted that colloids are important in the formation of laterites. Previous work by Mr. Mackenzie' has already indicated that iron may be adsorbed on quartz under conditions which could be expected in a lateritic profile, but no information was available for nickel or cobalt. Although adsorption possibly also takes place on minerals other than quartz, the latter is significant because silica is an important constituent of the silicate parent rocks. During lateritization, it is released to form free quartz and it is likely that it is initially extremely fine-grained. This would provide abundant opportunities for adsorption and it was de-

Jan 1, 1970

The production of petroleum in India (including Burma) increased from 334,811,624 gal.' ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

By R. A. Wagstaff

SINCE the time of the early Egyptians, the use of copper has been a boon to the life of most of the civilized world. Its use has been varied; in many connections, the art by which it attained its greatest usefulness has been lost. In this paper an endeavor will be made to take into consideration some of the many changes that have occurred during the last 40 years of copper-smelting operations. During that period the copper blast furnace has been almost forced out of existence by new methods of ore concentration-first, gravity concentration, and then flotation. These new methods of concentration introduced many new factors into the metallurgy of copper. The product was wet, it was fine and it was high grade. To overcome all these factors many changes have been necessary throughout the smelting agenda. New equipment has been necessary for transportation, unloading, sampling, bedding and moisturing in all smelting plants, especially the custom smelter. During the early days of "flotation," little was known about filtering or the use of an alkaline circuit; often the concentrate going to the smelter contained 20 to 25 per cent moisture. It is easy to imagine the difficulty arising with a product of this nature when it had to be shoveled by hand labor. To meet these conditions, mechanical unloading and sampling devices were soon developed. In many instances such good progress was made that actual costs for handling this unfavorable product were lower than those formerly incurred on the old product. Today most sampling of copper ores and concentrates is being done by mechanical sampling, pipe or augur sampling, or shovel sampling. Where concentrates are uniform in metal content, a great many of the plants now use pipe or augur sampling. For spotty ores, the old shovel sample with cone and quartering during the final stages is still in use. Where big tonnages are handled, mechanical sampling of concentrates is being done, with satisfactory results. To curtail slow and tedious cutting and mixing procedure, mechanical mixing boxes, splitters and cutters are used to cut down labor costs. MILLING As crude ores become scarcer, the use of milling operations increases. The few crude ores that are still smelted are used as fluxing types. To use these ores finer grinding has been found advantageous. This has made for better bedding and fluxing conditions, which in turn makes for faster smelting, lower fuel consumption and better metal recovery. The degree of fineness is more or less determined by the nature of the product. Most plants have set a standard of through ¾ -in. mesh screen for roaster- reverberatory smelting and through ¾ in. mesh screen for converter fluxes. For some refractory ores; even finer grinding has been found to be advantageous for good reverberatory smelting.

Jan 1, 1944

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,' Zr-Si,' and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies' and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.' Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,' was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By W. L. Zeigler

THE gravity concentrator of the Hecla Mining Co. was originally constructed in 1888 by the Milwaukee Mining Co., which was operating the Gem of the Mountains mine. It was purchased by the Hecla Mining Co. in 1900, and placed in operation 2 years later. At that time [ ] the capacity was only about 200 tons a day, but many additions and changes in equipment have been made so that the present capacity is about 800 tons. One of the outstanding improvements made was the substitution of Callow flotation cells for vanners, which occurred in 1915. The recent building of a flotation plant for treating jig tailings, and the construction of a modern surface plant at the mine, following the

Jan 1, 1928