Search Documents

By Thomas W. Dawson

The H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnages and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center to center of pulleys. It operated at a speed of 250 ft. 'per min-and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons was carried by the belt. whi1e: this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and, therefore, had to be crossed at each location to deliver coal to the river. After careful study, it was decided to transport this coal from the hoisting shaft to the river at each of these plants by belt conveyors.

Jan 1, 1925

By P. B. Bucky

THE purpose of this paper is to present a scientific method for deter-mining the proper span and shape of roof for safe and economical mining; at present, these two vital factors wherever pillars are left to support the roof are determined by local practice or general experience. To develop the method described here, experimental laboratory work was done. The arch adopted was a segment of a circle, a flat roof being considered an arch with an infinite radius. Hitherto, arches have been used underground without the background of stress analysis that generally precedes arch construction on the surface. In many cases results have not been as expected, because of the lack of knowledge of the factors affecting its strength and behavior. A theoretical and experimental study of arches should furnish informa-tion that will make it possible to design safe and economical surface structures as well as underground openings. For example, on the subject of mine drifts and tunnels, the present idea is that arching their backs increases their strength; this paper will indicate that this is not always true, and if it can be shown that under certain conditions arching becomes unnecessary an economic saving will result. In room-and-pillar work a question may arise as to whether arching the roof and gobbing the excavated material will result in timber saving, and a decrease in the dan¬gers from falls of roof. It is to be distinctly understood that each mine must be treated as an individual problem, and that answers to these ques-tions and many others can now be found after experimental laboratory data have been obtained.

Jan 1, 1934

By Oliver B. Hopkins

Peruvian production for the year 1935 amounted to 17,064,879 bbl., a record amount for any year, bringing the cumulative production of the country up to 188 million barrels. The 1935 figure is an increase of 785,769 bbl. over the 1934 total. The property of the International Petroleum Co. contributed 636,812 bbl. of this increase, and the Lobitos property 158,625 barrels. Exploration work in the country was again active, with attention focused on three areas, the Huallaga River, Lake Titicaca and the Coastal Zone of the Province of Tumbes. It is reported that in the Huallaga River area the Selden Breck Construction Co. has completed geological and engineering studies on its Pachitea River concessions and has ordered a drilling rig. In the Lake Titicaca region further studies in the vicinity of Pusi were made by Government geologists. During the period from 1906 to 1915, the Pirin anticline in this area produced 285,936 bbl. of low-grade crude. The Government holds 120,000 hectares of reserved lands in this area. In the Coastal Zone of the Province of Tumbes explorations by the Government were continued on the National Reserve, and a test location has been selected in the Quebrada Zapotal about 10 miles from the Port of Zorritos. An order has been placed in the United States for drilling equipment. LaBrea-Parinas Estate.—Production on the LeBrea-Parinas Estate reached an all-time high in 1935 of 14,756,914 bbl., an increase of 636,812 bbl. over the 1934 record. The total production from 1890 to 1935 was 148,541,523 bbl. During 1935 a total of 63,021 ft. was drilled in new wells and 5449 ft. in deepening existing wells; 23 wells were deepened and 29 new wells were completed, of which 27 were producers and 2 were dry holes. At the end of the year 2873 wells had been drilled on the Estate, of which 1838 were still productive. The remaining 1035 wells represent abandoned producers or dry holes. Practically all the drilling on the property has been done with cable tools, but during 1934 three strings of rotary tools were introduced. Experience with these outfits has shown that rotary equipment can

Jan 1, 1936

By George Frederick Kunz

The garnet-district of Bohemia is situated about 60 kilometers northwest of Prague, and is bounded on the north by Meronitz and Trebnice, 12 miles apart, and by Decany and Skan on the south. This region is covered with alluvium resting on the diluvium, which

Jan 1, 1893

Jan 1, 1966

[Billings Petroleum Section: Fraser M. Burback, chairman; N. J. Matthews, first vice-chairman; Charles B. Evans, second vice-chairman; and lion M. Madden, secretary-treasurer. Meets 3d Tues., Petroleum Club. California Coastal Section: Jack R. Severns, chairman.; Gilbert L. Jemmott, vice-chairman,- Jack A. Biren, secretary; and Robert L. Richardson, treasurer. Meets 3d Thurs.] [ ]

Jan 1, 1961

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit or rig front, the selection of the proper material and size of sucker rods, and the design of a pumping unit require that sucker-rod loads be known with a reasonable degree of accuracy. The segregation of rig losses, the proper selection and operation of prime mover and reduction unit, and the analysis of the operation of subsurface equipment require a knowledge of polished-rod horsepower. The investigation of such problems as the instantaneous stresses set up in a pull-rod line or backside crank installation when the well is suddenly hooked on, a study of such problems as the effect of anchoring the tubing on rod load, tubing stresses and rod horsepower, and an analysis of the effect of subsurface equipment on rod loads make it necessary to have a dynamometer that is rugged, which can follow the sudden changes in load without any lag or damping effect, which will record the load in its true position with respect to polished-rod movement, and which will give a card large enough to allow the desired effects to be measured accurately. The inadequacy of the spring or fluid-pressure type of dynamometers has been covered in detail1. The data given show that dynamometers of the spring or fluid-pressure type exert a damping action on the peak loads and the inertia and friction of their load-indicating mechanism introduces a phase lag in recording the load. A dynamometer of that type will not give the load in the correct amount and will not record it in its true position with respect to stroke or time. New Type of Dynamometer Fig. 1 shows a magnetic strain-gage type of dynamometer, to be described in this paper. The strain gage A is used for measuring the load in the polished rod, a washer B and knife edge C take care of initial misalignment and reduce bending in the compression tube of the strain gage. The complete instrument can be transported in the carrying case E.

Jan 1, 1935

By A. Dubé, G. Letendre, C. E. Beaulieu

An experimental study has been made of the time dependence of internal .friction and modulus of rigidity in- freshly quenched steels at room temperature. The effects of frequency, composition, and various thermal treatments are given. The kinetic 1aws observed cannot be fully explained by the so-called first stage of tempering and the transformation of retained austenite. It is suggested that the observed phenomena are due to the progressive immobilization of dislocations introduced by the martensitic transformation. It is generally agreed that the conversion of tetraginal martensite into cubic ferrite and ce-mentite occurs in three stages which at moderate rates of heating take place in the following temperature ranges:'-3 a) The first stage involves mainly a partial loss of tetragonality of martensite and the formation of ?-carbide between 95" and 175oC. b) The second stage consists of the decomposition of retained austenite between 230 and 290' C. c) The third stage covers the formation of ce-mentite between 290o and 400' C. The kinetic laws of these heterogeneous reactions have also been the subject of isothermal studies. Thus, Roberts, Averbach. and cohen3 report a very low reaction rate with a eutectoid steel at room temperature. For example, less than 10 pet of the contraction associated with the first stage is observed after 50 hr at room temperature. Hollonlon, Jaffe, and Buffum4 show that under the same conditions less than 10 pet of the tetragonality is lost. These results have led to the belief that martensite is a relatively stable phase at room temperature. On the other hand, it is well known that important structural changes occur in martensitic steels during the first few minutes at room temperature after quenching. This pretempering has at least two important consequences. In the first place, freshly quenched steels have a tendency to crack at room temperature, a fact which leads to the necessity of tempering as soon as possible after the quench. Another important consequence of pretempering a steel for short periods of time at room temperature is the stabilization of the retained austenite. Thus, as shown by Cohen,5 a very pronounced stabilization is effected with holding periods of 30 min at room temperature. Since these two effects are apparently not caused by the heterogeneous reactions mentioned above, they must be related to the rearrangement of structural defects within the martensite and retained austenite. According to the modern theory of dislocations, the shears required to effect the austenite-marten-site transformation may be realized through the motion of dislocations at the austenite-martensite interface and within the martensite plates.6 In this way, a martensitic transformation closely resembles a plastic deformation. In cold-worked solids, high concentrations of dislocations are left immediately after the plastic deformation and it seems reasonable to assume that appreciable densities of dislocations should also appear in the wake of a martensitic transformation. A considerable part of the high hardness of martensite would then originate in the obstruction of dislocations in analogy

Jan 1, 1961

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Wanted for a mill on the Ivory Coast of Africa an experienced amalgamator and millman. Salary, $160 to $200 per month. No. 18. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Chemist-metallurgist of broad technical training, university graduate, with experience in chemical and metallurgical research work, desires position, preferably in the East. Has successful past that stands investigation. No. 73. Member, mining and metallurgical engineer; thorough technical training, Ph.D., Columbia University, aged 39, married, with-an-extensive experience in smelting, mining, and economic geological work in U. S., Mexico, and South America, desires position as assistant to the Manager or Superintendent, or as a director of experimental and research work, with a reliable mining or metallurgical company. The West, Mexico, or South America preferred. No. 98.

Jan 6, 1914

By B. E. Warren

Jan 1, 1965

By P. N. Richards, M. K. Ormay

The present Paper extends the previous work on cold reduced, low carbon steels to preferred orientations developed after various heat treatments. In recrystal-lized rimmed steel, cube-on-comer orientations increased with cold reductions up to 80 pct. Above that {111}<112> and a partial fiber texture with (1,6,11) in the rolling direction dominated. During grain growth, cube-on-corner orientations have been observed to grow at the expense of {210}<00l>. In re-crystallized Si-Fe (111) (112) and cube-on-edge type orientations are dominant near the surface and the (1,6,11) texture near the midplane for reductions up to 60 pct. With larger reductions {111)}<112> and the (1,6,11) texture are dominant. In cross rolled capped steel a relationship of 30 deg rotation was observed between the (100)[011] of the rolling texture and the main orientations after re crystallization. Most orientations present in recrystallized specimens can be related to components of the rolling texture by one of the following rotations: a) 25 to 35 deg about a (110) b) 55 deg about a (110) C) 30 deg about a (Ill) THE orientation texture of recrystallized steel is of interest where the product is to be deep drawn, because preferred orientation is related to anisotropy of mechanical properties such as the plastic strain ratio (r value);1,2 and in electrical steel applications where a high concentration of [loo] directions in the plane of the sheet improves the magnetic properties of the material. It is interesting to note that both these aims are to a large extent achieved commercially, even though the orientation texture of cold rolled steel does not show large variation3 and the recrystallized orientations are generally given as being related to the as rolled orientations mostly by 25 to 35 deg rotations about common (110) directions.4-6 There is, as yet, no single completely accepted theory on recrystallization. The three mechanisms that have been investigated and discussed are: a) Oriented growth b) Oriented nucleation c) Oriented nucleation, selective growth Largely from the observations of the recrystalliza-tion process by means of the electron microscope,7-11 there is now considerable evidence that the "nucleus" of the recrystallized grain is produced by the coalescence of a few subgrains to form a larger composite subgrain, which finally grows by high angle boundary migration into the deformed matrix. From the intensive work on the recrystallization of rolled single crystals of iron, Fe-A1 and Fe-Si al-loys4-" he following observations have been made: 1) The change in orientation during primary recrys-tallization can usually be described as a rotation of 25 to 36 deg about one of the (110) directions. 2) The (110) axes of rotation often coincide with poles of active (110) slip planes. 3) If several orientations are present in the cold rolled structure, the (110) axis of rotation will preferably be a (110) direction that is common to two or more of the orientations. 4) With larger amounts of cold reduction (70 pct or more) departure from these observations became more frequent. 5) After larger cold reductions, rotations on re-crystallization about (111) and (100) directions have been observed. K. Detert12 infers that a rotation relationship of 55 deg about (110) directions is also possible, by stating that the recrystallized orientation {111}<112> can form from the orientation {100}<011> of cold reduced partial fiber texture A.3 The observation by Michalak and schoone13 that (lll)[l10] formed during recrys-tallization in fully killed steel containing (111)[112],— as well as (001)[ 110] which is related to the {111}<011> by a 55 deg rotation about <110>-implies a possible 30 deg rotation relationship about the common [Ill]. Heyer, McCabe, and Elias14 have recrystallized rimmed steel after various amounts of cold reduction, by a rapid and by a slow heating cycle and found that the preferred orientations strengthened with increased cold reduction. The most pronounced orientation up to about 70 pct cold reduction was found to be {1 11}< 110>, after 80 pct cold reduction both {111}<110> and {111}<112>, after 85 and 90 pct cold reduction, {111}<112>, and after 97.5 pct cold reduction it was {111}<112> and (100)(012). In the present work, the orientation textures of the recrystallized specimens are examined under various conditions of steel composition, amount and method of cold reduction, and method of recrystallization. The relationships between the preferred orientations of the as rolled and recrystallized specimens, and the conditions for the formation of the various orientations during recrystallization are investigated.

Jan 1, 1970

By Gerald Sherman

In the southern field of the anthracite region of Pennsylvania, many of the coal seams dip at angles of 40" to 50" from the horizontal. For transportation purposes, "tunnels" are driven across the coal measures and, occasionally, "rock gangways," beside the seams and parallel with them. The use of gangways driven in country rock appears to be increasing, as they avoid the maintenance of long gangways in coal, which eventually are driven to the colliery boundaries, and permit mining from a number of intermediate blocks without interference. The rock consists of slates or sandstones of moderate hardness, which may range into very hard, highly siliceous, fine-grained conglomerates. In this distinctly bedded formation, the direction of the heading, whether parallel with or across the structure, makes it necessary to distribute the drill holes in a different pattern to break the ground, but does not change loading conditions. In 1932, practically all the mucking was done by hand, and it was the established custom to use four men on two drills for drilling and breaking the ground, and five for loading it out. A driver and mule was needed in addition, to assemble the rock cars at a siding or branching track in the rear, pending their final disposal. This might occupy the driver&apos;s whole time, or if the length of haul were short, he might be able to do other useful work. It was thought possible in 1932 to reduce the cost of driving such headings in rock by mechanical loading, and to investigate this subject a scraper loader was used in a section of tunnel then being driven. Operations while driving 195 ft. of this tunnel using a scraper loader were carefully observed. Time studies were made of the loading, and records made of the routine of breaking ground, but not in such detail. Tunnels or gangways in the colliery are 7 ft. high above the rails, by 10 ft. wide, which requires a minimum of 8 ft. in height, broken to allow for rails and ties. This cross section is of sufficient size to permit the use of any one of several types of power loaders, but for this demonstration it was found most convenient to use a scraper loader.

Jan 1, 1937

By S. R. Goodman, Hsun Hu

The rolling texture of an 18-8 stainless steel (Type 304L or 304) has been found to change gradu -allv from the (110)[112] brass type to the (123)[412] copper type as the rolling temperature increases from 200° to 800°C. This texture transition is accompanied by a change in the stacking-fault frequencv or probability, similar to those found pre- In a series of previous publications, it was shown that the rolling texture of high-purity silver changes gradually from the brass type to the copper type with increasing temperature of deformati~n. A similar temperature dependence of rolling texture transition was found in electrolytic copper3—by lowering the temperature of deformation, the normally observed rolling texture of copper changed gradually viously in nonferrous fcc metals—the stacking-fault frequency decreases rapidly with the formation of the copper type texture. These results strongly indicate that the temperature dependence of copper type == brass type texture transition and its correlation with stacking-fault frequency is a general phenomenon in fcc lattices. to the brass type.* In both of these metals, the

Jan 1, 1964

By Brian F. Dyson

The surface tensions at 1550°C of some Fe-S alloys (in the range 0.008 to 0.052 wt pct S), Fe-Sn alloys (0.31 to 48.4 wt pct Sn), Fe-P alloys (0.038 to 2.38 wt pct P), Fe-Cu alloys (2.15 to 22.8 wt pct Cu), and Fe-1 pct C-S alloys (0.005 to 0.076 wt pct S) along with the surface tension of the base iron have been measured by the sessile-drop method. A mean value of 1754 dynes per cm was found for the surface tension of the base iron. Sulfur was found to be highly surface-active, the surface-tension results being in quantitative agreement with existing data. Tin and copper were found to be less surface-active than sulfur while phosphoms was completely nonsurface-active. The surface tensions of Fe-1 pct C-S alloys were found to be lower than those of the Fe-S alloys containing the same sulfur content. This was shown to be a mmzifestation of the increase in the thermodynamic activity of suZfur by carbon. It is only in recent years that attempts have been made to measure the surface tension of liquid iron of known high purity.1-3 Earlier measurements4-7 were made on liquid iron containing variable amounts of what are now known to be surface -active solutes. The exact value of the surface tension of liquid iron is still, however, open to some doubt. Halden and Kingery&apos; reported a value of 1720k 34 dynes per cm at 1570°C, Kozakevitch and Urbain8 gave 1790k 25 dynes per cm at 1550°C, while Van-Tszin-Tan et al. obtained a value of 1865k 37 dynes per cm at 1550°C. The first systematic investigation into the effect of controlled solute additions on the surface tension of iron was made by Halden and Kingery.&apos; They showed that sulfur and oxygen were highly surface-active, whereas nitrogen was only slightly active, and carbon inactive. A subsequent investigation by Kingery indicated that two other group-6B elements, selenium and tellurium, were also surface-active. This highly surface-active nature of sulfur and oxygen has recently been substantiated by Kozakevitch and Urbainla and Van-Tszin-Tan et al. l1 Kozakevitch and Urbainl2 have also conducted an experimental survey of the effects of a number of metals on the surface tension of liquid iron. Their surface-active nature was, in all cases, less than that of the group 6B elements. The present investigation was undertaken to study in more detail the surface tensions of dilute Fe-S alloys and to measure the surface tensions of binary alloys of iron containing phosphorus, copper, and tin. The effect of sulfur additions on the surface tension of Fe-1 pct C alloys was also determined. EXPERIMENTAL PROCEDURE The sessile-drop method was employed in the present investigation. An apparatus was built similar in principle to that described by Humenik and Kingery.lS It consisted of a horizontal silica tube, which could be evacuated to pressures less than 10-5 torr, with its central portion surrounded by a water jacket within which was a high-frequency coil. This generated heat in a tantalum susceptor placed inside the silica tube, which in turn radiated heat to the specimen mounted on a recrystallized alumina plaque. Temperatures were measured by an optical pyrometer and photographs of the molten drop were taken on a fixed-focus plate camera giving a magnification of X2. Surface-tension values were determined from the resultant drop using the method described by Baes and Kellogg.l4 The high vapor pressure of molten iron made it necessary to conduct all the experiments under a 1/4 atm of argon (greater than 99.995 pct purity). The analysis of the base iron used in the investigation is given in Table I. Each sample was approximately 3 g in weight and had a hemispherical base to ensure a uniform advancing contact angle on melting. The iron alloys were prepared individually in the sessile-drop apparatus by drilling a hole in the top of each sample and adding the required amount of solute, the drops being analyzed after the experiment. This method of preparation had the advantage of ensuring a consistent minimal contamination by oxygen due to refractory attack and also allowed surface tension to be measured at the same time. Every precaution was taken to ensure that the specimen was not contaminated by grease when it was introduced into the apparatus, the samples being cleaned in acid, dried in alcohol, and rinsed in petroleum ether. All handling was done with tweezers. Once the specimen had been placed inside the susceptor, the furnace was evacuated and the Sample leveled. The furnace was then degassed at approximately 1000"C before the argon was introduced. In every case the surface tension was determined at 1550" C.

Jan 1, 1963

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10&apos; APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26&apos; API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.&apos; Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By W. A. Straw

IN the manufacture of telephone apparatus a number of nonferrous sheet metals are blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming, characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper.

Jan 1, 1931

By Theodore Hatch

The pneumatic rock drill operates essentially as a crusher. The rock is shattered into a powder that is removed from the drill hole by the air stream introduced through the hollow drill steel. Particles thus produced vary in size from 1/4 in. or larger down to diameters too small to be revealed by the ordinary microscope. The power consumed by the drill is proportional to the new surface area of the powdered material, therefore the greater the proportion of "dost" produced, the higher the power consumption and the lower the drilling speed. A considerable amount of material ejected from the hole settles on the rock and much of this falls back as the mound builds up to be crushed further before it is removed again. The cushion of dust at the bottom of the hole reduces the effectiveness of the blow of the bit and thus lowers the rate of drilling. The unfavorable working conditions created by the dust also reduce the drilling speed by lowering the efficiency of the operator. Thus, the dust produced by rock drills constitutes a serious drawback to economical performance on all drilling operations. To the economic objections, one must add the more important objection to the health hazard created when the dust contains free silica (quartz). The silicosis problem is a familiar one in many mines, tunnels, and other underground operations as well as in quarries and other types of open rock excavation. Dust is a necessary end product of all pneumatic drilling operations. Its production cannot be eliminated although the proportion of microscopic particles can be reduced by using improved drill steel, proper methods of sharpening, more efficient drills, etc.—improvements that increase the drilling speed largely by increasing the size of the cuttings. The absolute improvement secured in this way is not great, however, and the pneumatic drill must always remain a dust-producing machine. Definite benefits do result, on the other hand, from the use of dust-control equipment that captures the dust as it emerges from the hole and conveys it to a remote point of discharge. Dust production continues, but dust dispersion into the atmosphere is prevented. The dust is removed as rapidly as it is formed, with the following results: (I) The silicosis

Jan 1, 1937

By H. S. Geismer

There are three general methods available for obtaining commercial brown iron-ore: hand-screening; washing; and washing and concentrating. Hand-screening has produced a large tonnage of ore in the past, but is rapidly falling into disuse, except as a preliminary step, largely because modern furnace-practice requires all forcigii material to be separated from ores before they are deliv-

Jan 1, 1912

By David B. Reger

Sharp declines of initial production of both oil and gas occurred in West Virginia during 1943. There was only a small decrease in the number of ncw wells, but these wells did not show the quantities of oil and gas that might have been expected. The same situation prevailed both as to routine drilling in old pools and as to exploratory wildcat wells. Out of 42 wildcats drilled, 19 resulted in small commercial gas wells, and 2 in small commercial oil. No new oil pools were discovered, but the proved limits of several old pools were considerably extended, giving 4200 acres of newly proved oil territory. Three new gas pools, resulting from discoveries made in 1942 and former years, came into definite activity. The newly proved gas territory in these and in various extensions of old pools is 39,000 acres or more. It is doubtful whether the newly proved reserves of either oil or gas will balance current withdrawals. The account of operations, as gathered from trade journals and other reporting services, shows that 696 new wells were drilled, resulting in 82 oil wells with 919 bbl. of daily new production; 475 gas wells with 454,735,000 cu. ft. of daily open flow, and 137 dry holes. Also, 57 old wells were drilled to deeper sands, with 3 bbl. and 11,484,000 cu. it. of added production. On the new wells, the oil average was 11.2 bbl. per well per day, and the gas average was 957,337 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 19.68 per cent. On deeper drilling the ratio of failures was 14.03 per cent. The greatly decreased average initial gas-well production in 1943, as compared with 2,270,406 CU. ft. per well in 1942, is directly attributable to the abrupt decline of completions in the Charleston gas field, which reached its peak in 1942. Production of oil for the year was estimated by the U. S. Rureau of Mines as 3,349,000 bbl., as compared with 3,574,000 bbl. in 1942. Production of natural gas for the year is estimated by the author as 210,000, 000,000 cu. ft., compared with the U. S. Bureau of Mines final figures of 215,193,-000,000 cu. ft.* in 1942.

Jan 1, 1944

By Ralph J. Schilthuis, William Hurst

The nature of the forces that are important in producing the oil in the East Texas field and the manner in which these forces are affected by the rate of production have always been problems of outstanding interest. These questions are of great interest to the industry as a whole on account of the economic importance of the East Texas field and to the engineers in particular on account of the unique character and behavior of the field. Subsurface pressure data throughout the field have been collected systematically, so that a quite complete history of the reservoir pressures has been kept as the field has been developed and produced. Subsurface samples of the oil and gas have been taken and these have been examined to obtain data on the physical properties of the reservoir fluids under the actual conditions of temperature and pressure. All of these data have been valuable because they have afforded the basis for a careful study of the means by which the oil is produced. It is the purpose of this discussion first to point out several of the important facts revealed by the data mentioned and then to describe studies that have been made concerning the interpretation of these facts. Reservoir Pressure Data and Properties of Oil The reservoir pressure data on the East Texas field have shown conclusively that the pressures are readily affected by changes in the rate at which the field is produced. This can well be seen in Fig. 1, where the average reservoir pressures obtained from time to time are plotted with the daily production rates and the cumulative production of the field. It is noted that the average reservoir pressure has declined irregularly, depending upon the rate of production, from the estimated original value of 1625 Ib. per sq. in. to the value of 1228 lb. per sq. in. observed for Aug. 11,1934. The decline in pressure has been more rapid at the higher rates of production than at the lower rates. In contrast, the average reservoir pressure has increased, on several occasions, upon reduction of the withdrawal rate from a high value to a lower value. The reservoir pressure data have also shown that a definite gradient in pressure has existed across the field from west to east since the begin-

Jan 1, 1935