Search Documents

By M. Metzger, L. E. Hendrickson

Grain boundary attack in 16 pct HCl was found to be substantially the same at low penetrations in zone-refined aluminum (individual impurities 0.1 at. ppm), superior electrolytically refined aluminum (51 at. ppm), and aluminum with various impurities at much higher levels. It was concluded that impurity atom segregation affecting corrosion would have been detected and that the corrosion susceptibility did not originate in this segregation but in the structure of the boundary. It was pointed out that the significance of most previous studies in this system had been obscured by an unrecognized autocatalytic copper reaction. Although general corrosion rate was also impurity-insensitive , there was shallow pitting attributed to iron seg-regation and a hillocked surface texture associated with copper; these were interpreted as due to cathodic damage affecting- cathode distribution. THE grain boundary corrosion suffered by high-purity aluminum in hydrochloric acid has been the object of some interest (the earlier work is summarized in Ref. 1). The central metallurgical question here is whether the corrosion susceptibility of a boundary originates in its structure or in impurity atom segregation. An attempt to study this question revealed large catalytic effects associated with small quantities of the copper impurity in the aluminum, 220 ppm, or in the corrodent, and these magnified the preferential boundary attack and obscured the intrinsic susceptibility question.' After the catalytic effects had been examined,"' test conditions could be designed to avoid them and methods developed for studying the shallow boundary penetrations prevailing when they were absent.= It then became possible to determine whether intrinsic boundary corrosion in aluminum involves impurity segregation. The older work provided no firm information on grain boundary segregation of specific solutes influencing corrosion although several studies suggested iron segregates.4,5 perryman4 found in 10 pct HC1 that the slowly developing (microns per month) grain boundary grooves were deeper in material of higher iron content (range 10 to 550 ppm, with 5 to 80 pprn Cu) but he did not measure the depths of general corrosion, which were probably several times greater, and his reference surfaces may have varied more than did the groove depths. Metzger and Intrater's results for 20 pct HC~,' which yielded higher time-average rates (mm per month) and deeper penetrations, suggested that boundary segregation of iron (range 4 to 230 ppm, with 22 pprn Cu) decreased the penetration rate. However. in the stronger acid the autocatalytic l.E. HENDRICKSON, Student Member AIME ,and M. METZGER, Member AIME, are Research Assistant and Professor of Physical Metallurgy, respectively, Department of Mining, Metallurgy and Petroleum Engineering, University of Illinois, Urbana, Ill. Manuscript submitted March 11, 1968. IMD effect of the copper impurity is greater1,2 and it is now evident that their corrosion rates had been much magnified by this effect and did not provide a proper basis for the analysis of segregation. In exploratory studies of other solutes (made under the same conditions), 1000 ppm additions of Mg, Mn, or Si or 100 ppm Ca were without effect.1 Montariol6 noted that boundary attack in 22 pct HC1 persisted after zone refining although with fewer deep fissures (ranges 0.06 to 4 ppm Cu, 4 to 23 ppm Fe). Autocatalytic effects may have influenced these results also and those of Perryman.4 The present objective was, as a first step, to see whether quantitative tests designed to exclude autocatalytic influences would indicate the existence of low-level impurity effects on intrinsic boundary corrosion. Comparison of electrolytically refined with zone-refined aluminum of lower copper and iron contents revealed no differences in boundary corrosion, but certain impurity-sensitive differences in general corrosion morphology were noted and investigated further at higher impurity levels. I) EXPERIMENTAL PROCEDURE A) Material. A selection from commercially available material was made with the cooperation of several producers. An electrolytically refined lot (III-A, 1 ppm Cu, 2.4 ppm Fe) studied previously3 provided a starting point. Since material of substantially higher copper content could not be used if the autocatalytic corrosion reaction were to be avoided,2,3 a lot (III-B) of about the same purity was added as a check, two zone-refined lots (I-A and I-B) with copper and iron an order of magnitude lower were selected for comparison, and an intermediate lot (11) was included. Analytical data are given in Table I. For copper in I-B and iron in I-A and I-B, the actual concentration is thought to be near the limit given, i.e., about 0.1 ppm. For titanium, vanadium, and chromium in III-B, the actual amounts are thought to be, like those in III-A, substantially lower than in the zone-refined lots (these elements concentrate in the solid on freezing). Data are given later for some additional lots surveved. B) Specimen Preparation and Procedure. one by 3 cm blanks with a notched stem were cut from 1-mm cold-rolled sheet, annealed 24 hr in air at 650°C, and quenched in an air stream (42°C per sec initial cooling rate, 100 sec to cool to 100°C). The high annealing temperature maximized diffusivities and approach to equilibrium impurity distributions. A water quench, in principle more efficient in preserving the distribution established, was undesirable because the boundaries were almost plane and they tended to shear and migrate during the quench and thus to be separated from any existing impurity atmosphere. Test procedures, previously described,3 involved electropolish-ing, etching 2 min in 10 pct HF at 24.0°C, and expos-

Jan 1, 1969

Jan 1, 1947

By Paul M. Tyler

FULLY a decade ago, demand for ground mica began to exceed supplies of scrap mica from manufacturing operations and of waste block from feldspar and sheet mica mining in the United States, with the result that in recent years the market has absorbed larger and larger quantities of mica recovered as a by-product from clay washing,1 as a joint product with kyanite12 and by grinding schists. So far, only schists that contain a large percentage of mica have been utilized for making ground mica, but already there has been a good deal of wishful thinking with regard to recovering mica as an aid to the prospective working of low-grade gold ores and ores of certain base metals. With wet-ground mica selling at $60 to $100 a ton and even dry-ground mica worth over $20 a ton, many ores that could not be considered as otherwise workable under present conditions will show commercial possibilities if they can be made to yield even a relatively small percentage of salable mica. An interesting paper might be written on the coming role of industrial minerals as joint products of metal mines. It is largely a matter of markets. Many years ago I watched the mess left behind the gold dredges in the mountains of Colorado and thought of the Denver sand and gravel operators who prided themselves upon their canniness in providing devices for catching gold merely as an incident to their regular business of selling what we miners classed as "tailings." Nowadays almost every milling or mining operation near settled communities finds use for at least part of its waste for road material or concrete aggregate and several eastern iron mines have gone into the crushed-stone business. Promoters now mention fertilizer "filler" as potentially salable at all the way from $1 to $10 a ton, or whatever is needed to cover costs of mining and treating the "ore" and leave the metal values as "clear profit." In emulating the pork packers in their efforts to utilize "everything but the squeal,"

Jan 1, 1938

By Richard D. Hagni

Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in millproducts. The mill dressing engineer should be more aware of the types of beneficiation problem that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations ofthe mineral constituents of an ore or mill product can be visually determined. This advantage provides solutions to many beneficiation problem. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in flocculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 1, 1979

By V 7. 0 / 300 dpi

DRILLING in the Oligocene potash basin of Alsace prior to 1927 had shown important differences of level in the salt beds thus encountered. To explain this a somewhat unsatisfactory hypothesis of faulting had been advanced. During the latter part of 1926 and the beginning of 1927- our firm was engaged by two organizations for the purpose of trying to supplement, by an electrical survey, the geological data thus far collected. As a re-sult of this exploration it was possible to affirm that salt dome structures were present in the Oligocene basin of the Upper Rhine, something heretofore absolutely unknown in that region. Two salt domes were actually outlined, one, near Meyenheim, was made the subject of a communication to the Academy of Sciences, by G. Friedel2; the other, near Hettenschlag, was briefly dis-cussed by C. and M. Schlumberger3 before the same academy. The purpose of this paper is to indicate the strati-graphic and structural conditions of the area where these salt domes were found; to discuss the results of the electrical survey which led to the location of the domes, and indicate the new geological outlook which such a discovery suggests.

Jan 9, 1928

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By Finney, W. R.

MUCH has been said and written of the "Big Inch," of the terrific obstacles encountered in its construction, of the colorful and tough men engaged in its building, but little has been publicized of the engineering and economic problems behind the scenes. Long before Pearl Harbor it was apparent to the petroleum industry that a critical oil shortage could be expected along the Atlantic seaboard, owing to delay in tanker deliveries as a result of convoy movements, and to allocation of vessels for foreign shipments. This area, with a normal consumption of approximately 1,800,000 barrels per day of oil and products, was almost entirely supplied by tanker. Pipe lines supplied an average of only 20,000 barrels per day in 1939, 40,300 barrels per day in 1940, and 55,000 barrels per day in 1941. A small amount of oil and products was also delivered via barge.

Jan 1, 1943

By R. H. Atkinson

With the object of improving the melting, casting, and working of palladium and 95.5 pct Pd-4.5 pct Ru, the effects of different melting atmospheres (reducing, oxidizing, and neutral), crucible linings, and annealing atmospheres have been studied. Some interesting observations are included about the solubility and diffusion of gases in palladium. THE object of the present work was to ascertain the effect of oxidizing, inert, and reducing ambient atmospheres on the melting and casting of palladium and a Pd-Ru alloy commonly used for jewelry. The need for such a study was indicated during World War I1 when jewelers experienced difficulty in their attempts to make small castings of the torch-melted Pd-Ru alloy by the lost-wax process. When the metal was melted under oxidizing conditions similar to those used for platinum, the castings were gassy; on the other hand, if the melting atmosphere was reducing, the castings were hot-torn and brittle. General Experimental Procedure Pure palladium sponge (99.9 pct Pd) and pure ruthenium powder (99.8 pct Ru) were used for making small ingots (50 g) of palladium and 95.5 pct Pd-4.5 pct Ru by induction melting. The coil, 3 in. high by 2 in. ID with 16 turns, was energized by a 20 kva Ajax high frequency converter. The melting crucibles, so-called sand crucibles, which were made of a highly refractory fireclay, were lined with different materials, including proprietary magnesia, alundum, zircon, and zirconia

Jan 1, 1957

By Donald E. Ackerman, Norman B. Pilling

The solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion. Introduction The discovery, development and engineering application of iron alloys resistant to corrosion may well claim a place among the important developments in metallurgy of the past two decades. The varied demands of industry coupled with the skill of the metallurgist have resulted in the production of an extensive group of steels and alloys ranging from the now familiar "stainless " chromium steels of the kitchen to special alloys of great chemical complexity for particular, exacting needs. Any adequate description of the important properties of these-— physical, chemical and economic—would be a formidable undertaking.

Jan 1, 1929

By Miguel Bustamente

In 1890 I mas manager of a mining enterprise in the State of Michoacan. The ores were composed principally of iron pyrites (much decomposed), in a quartz matrix, with native gold in very irregular grains. Some portions, however, carried their metallic value in a matrix of calcite arid siderite. The mill in which the ores were treated consisted of two 800-lb. stamps, two amalgamating-plates, four pans, two automatic washers, two Frue vanners, and the necessary accessories for assaying, retorting and refining gold. The plant, originally erected with American capital, and directed by competent Americans, passed in 1890 into the hands of Mexican owners. On taking charge of the business I found on hand a large amount of ore assaying 35 grammes of gold per metric ton (about 1 oz. Troy per ton of 2000 lbs.); but the company was losing money, and was about to abandon the business. Obviously, the difficulty lay in the treatment of the ore. The extraction of gold scarcely reached one-tenth of the assayvalue ; the loss of mercury was considerable; and high freight; charges excluded the alternative of exporting the ores. This situation naturally suggested that amalgamation was not applicable to these ores, and that a more appropriate method must be adopted. The cyanide- and chlorination-methods had been tried already, without practically satisfactory results. For the first few months I employed a combined system, extracting a part of the gold by direct amalgamation, and cyaniding the concentrates. This saved 32 per cent. of the assay-value, but the cost of milling still exceeded the proceeds. Meanwhile I observed

Jan 1, 1902

R. L. Bullock (St. Joseph Lead Co., Bonne Terre, Mo.)— The progressive approach of The International Salt Co. as described by Mr. Ryon is certainly commendable as is his paper. St. Joseph Lead Co. has been shooting AN/FO in 13/8 to 1 1/4-in. holes for several months now (as of October 1960) on a trial basis. The results thus far obtained are excellent, but conclusive evidence at this date is premature. One point that he gave should interest even the most ardent skeptic. That is, they are getting a detonation of the 1 1/4-in. ANDO charges in 2 1/4-in. holes. In light of its low sensitivity and critical diameter, this would appear to be one of the worse conditions that one could expect in which to get proper detonation of AN/FO. It has been shown* that partial confinement sometimes decreases sensitivity of a column of explosive because the air space above the explosive becomes highly compressed and in turn compresses the explosive prior to passage of the detonation front. Apparently, this does not happen in their shooting and the poor explosive coupling caused by the 2 1/4-in. holes yields a minimum of overbreak and is an ideal condition for their back.

Jan 1, 1961

By A. E. Hall

The paper gives a general solution of ventilation net- works where densities play an important role and fans operating at different densities from branch densities are considered. Both the physics and computing techniques needed to deal with these networks are discussed.

Jan 1, 1977

By Oscar Glaeser

THE mine and plant of the United Verde Copper Co., located in Yavapi County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending-about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level.

Jan 1, 1929

By Bruce T. Stanley

The concepts of ore reserve estimation at the Henderson mine are reviewed presenting a geostatistical approach and procedure as applied. Specific problems encountered are recapped and explained as to the nature and resolution thereof. The methodology and results are shown, along with an approximation of computer usage and capacities needed. The scope of the paper is to set forth an example of actual application, usage, and benefits realized from such a procedure. Local Conditions The Henderson molybdenite deposit is located in central Colorado about 69 kilometers west of Denver. The geology consists of a classic subvolcanic ryolite porphyry sequence with quartz-molybdenite mineralization occurring in an extensively fractured granite stock complex. Being assymetric and bilobate in section, the orebody measures approximately 300 meters thick and 600 meters by 1200 meters in plan. The orebody is sampled by means of underground drill holes which create an east-west fan pattern spaced roughly 60 meters apart in the north-south direction. Approximately 27,000 meters of drill hole assayed on 3.04-meter intervals were available for analysis. Recovery on the core is about 95 to 100 percent, thereby affording us with reliable data all prepared to the same standards.

Jan 1, 1977

Recent start-up of a new 3450 t/d (3800 stpd) copper-zinc concentrator complex in northern Manitoba, Canada, is expected to open new reserves and dramatically cut transportation costs for Hudson Bay Mining and Smelting Co.'s Snow Lake operations. The new $C33-million mill is located in Stall Lake, Manitoba, and includes a new crushing and grinding facility and two flotation circuits for the production of 23-25% copper and 55% zinc concentrates. A small amount of lead concentrate will also be recovered. The plant will produce some 145 000 t/y (160,000 stpy) of concentrates, to be shipped by rail to the firm's Flin Flon copper smelter and zinc refinery complex, located 177 km (110 miles) to the west on the Saskatchewan-Manitoba border.

Jan 9, 1979

By Michael B. Gross

A numerical study of the vulnerability of unlined tunnels in jointed rock has been performed with the STEALTH computer program, using the CAVS model for jointed rock. CAVS, for Cracking And Void Strain, is a constitutive model that can simulate the initiation/propagation of fractures and the slip along fracture planes in a jointed rock mass. The CAVS model is unique because it represents a spatially oriented approach to rock failure, rather than the traditional invariant formulation, and because the CAVS submodels for slip friction and slip-induced dilatancy are used to represent the weakening influence of joints, rather than applying ad hoc modifications to the elastic moduli of the host rock. The CAVS model, as embedded in the STEALTH computer program, has performed numerical simulations of tunnel collapse at high overstress levels. These calculations show that the ultimate strength of the tunnel depends strongly on the joint properties, and that the results of the calculations are in qualitative agreement with the observed data for collapse of a tunnel in tuff.

Jan 1, 1984

By A. J. Boyer, T. R. Meadowcroft

An experimental determination has been made of the efject of surface diffusion on the vapor pressure obtained in a Kwudsen cell. The results show that a knife-edge orifice in a molybdenum lid may give erroneous results for the vapor pressure of silver. when a correction suggested by winterbottom and Hirth is made, the results become meaningful. Experimental work with cylindrical orifices in molyhdenz~m lids and knife-edge orifices in ceramic lids shows that good vapor-pressure results may he obtained when the orifice is designed so that ejfusion is the only significant source of weight loss. THE Knudsen effusion cell technique has been used by many investigators to study relative and absolute vapor pressures over metals and alloys at elevated temperatures. As a result of this interest, some theoretical studies have been made of geometric factors affecting effusion from the orifice of a Knudsen cell. A review of these studies has been made by Margrave.1 Recently, Winterbottom and Hirth2 have suggested that a physical effect, that of condensation, surface diffusion, and re-evaporation, may seriously affect Knudsen cell measurements, especially when a knife-edge orifice is used. Inasmuch as many of the present vapor-pressure data have been obtained using knife-edge orifices. it was felt that an experimental evaluation of the effect of surface diffusion on Knudsen cell measurements would be of value both in the design of the cell orifice and in establishing realistic estimates of the limits of error for existing data. The experimental program was in two sections. Firstly, measurements of the vapor pressure of silver were made in cells with cylindrical and conical orifices in which the surface-diffusion contribution to the weight loss should be negligible. These results were correlated with existing data to give a reliable measure of the real vapor pressure of silver. Secondly, measurements made using knife-edge orifices were corrected using the surface-diffusion theory of Winterbottom and Hirth2 and were then compared to the real values. The experimental arrangement is shown in Fig. 1. The balance was an Ainsworth RV-AU-1 automatic recording microbalance capable of measuring weight changes of ±0.02 mg on a total load of up to 100 g. The temperature was measured by an optical pyrometer signted on the bottom of the suspended crucible. The temperature readings were calibrated in a separate experiment in which pyrometer measurements were made while at the same time thermocouple readings were taken of the temperature at the inside top and bottom of the crucible. The range of reproducibility with this technique was ±4°C. A constant voltage source maintained a temperature of ±2°C at 1200°C over 10 hr. Silver of 99.99 pct purity was used in nonporous alumina crucibles. Lids of molybdenum, tantalum, or magnesia were cemented to the crucible using a sodium silicate cement. Table I shows the characteristics of the lids used. The vapor pressure is obtained using the basic Knudsen formula:

Jan 1, 1965

By F. S. Knoll

The expanding role of electrostatics as applied to minerals and related fields is covered in this paper. New and existing forms of electrostatic separation are classified into two broad groups: separation of charged particles and separation of neutral particles. The basis for each form of separation is discussed along with particle examples and results obtained.

Jan 1, 1986

By Paul Tyler

THE extensive employment of nonmetallic minerals antedates the use of metals, but only within the last two decades has the production of nonmetals begun actually to keep pace with the complicated activities which characterize the so-called Machine Age. The economic changes ushered in by the Industrial Revolution were reflected first in an increased demand for metals and for fuels. In the modern sense, therefore, the nonmetallic mineral industries are new and afford new opportunities for engineer and economist alike. A certain amount of caution is indicated, therefore, before attempting to apply ready-made formulas to the problems of these industries. Economics is not an exact science. In the field of production technology where the number of variables is fairly well known, the principles of economics are readily applicable, but as the student proceeds through the province of marketing into the unexplored regions of psychology and sociology he must distinguish carefully between scientific reasoning and purely metaphysical speculation, even when the latter masquerades as economics. The present paper attempts to prove no preconceived theorems and is designed primarily to stimulate careful thinking on sundry neglected phases of these industries. An attempt is made to differentiate the general problems into single aspects which afford promise of being comprehended separately; also, some fundamental statistical data are presented, but merely to indicate a method of scientific approach applicable to more intensive studies.

Jan 1, 1933

By D. Gupta

Rates of autothermic reactions are sensitive to temperature variations to the extent of potential extinction of the reaction. Such reactions, when carried out in the countercurrent mode with feed-back of energy between reacting phases, may result in the possibility of multiple steady-states. In regions of great sensitivity, minor variations, especially feed-temperatures, are an important criterion for such instabilities. Mathematical models have been used to delineate the parameter-fields in which instabilities might occur. The metallurgical system chosen to experimentally verify the above theoretical findings was the exothermic oxidation reaction of magnetite to hemitite.

Jan 1, 1977