Search Documents

By W. F. Laverty

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs' absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By T. S. Lundy, R. A. Padgett

The fact that cobalt diffuses in silver at a much slower rate in a region near a free surface than in bulk material has been demonstrated in a variety of experiments. Various possible mechanisms of this near-surface effect (NSE) are examined in light of experimental evidences. The tendency for surface segregation of some solute atoms appears to be a likely mechanism to explain the effect. UNIDIRECTIONAL and isothermal diffusion from a plane source of radioactive tracer into an isotropic, homogeneous medium follows the Gaussian solution to Fick's second law, or: where A(x,t) is the position and time-dependent concentration of the diffusing species, M is the quantity of diffusant per unit area initially at x = 0, and D is the diffusion coefficient. For a given time, say t = tl, one can easily see that: d In Aixji)_____1_ r2] d(x2) 4Dti Thus, if diffusion data obtained by serial sectioning are plotted as In A(x,tl) vs x2, the diffusion coefficient is obtained from Eq. [2]. The ideal behavior seldom is observed in real systems. Deviations from ideality generally occur either at small or large values of penetration distance. The overall picture is shown schematically in Fig. 1 where Regions I, 11, and 111 are due, respectively, to some near-surface effect or effects (NSE), volume diffusion, and short-circuiting effects. For different systems and conditions of specimen preparation and analysis, the relative importance of Regions I, 11, and I11 may be drastically different. Region I is completely absent in many systems and there is no NSE. In others, however, there may be considerable difficulty in determination of volume diffusion coefficients due to the overshadowing influences of Region I. Such is particularly true when indirect techniques such as the surface concentration decrease or the Gruzin method' are used to find D. In this paper several experiments which had as their goal a better understanding of near-surface effects are reported. Specifically, it is well-known that unusual penetration behavior results for the diffusion of several impurities in ilver- and that considerable controversy exists with regard to interpretation of the published diffusion data. We chose to examine those unusual results which occur for cobalt diffusion in monocrystalline silver395 primarily because knowledge of experimental procedures and materials were readily available. Both radioactive co60 and co5' could be utilized to offer a wide range of available concentration of the diffusing species. Experiments were also performed on the diffusion of AgnO in silver. They gave base-line data for the system—both for technique evaluation and for examination of the vacancy distribution near the surface. I) PROCEDURES Cylindrical-shaped specimens 1.25 cm diam and 1 to 1.25 cm long were cut from 99.999 pct Ag single crystals obtained from Monocrystals Co., Cleveland. One end surface of each specimen was polished flat and etched with a mixture of 20 ml saturated Cr03 solu-tion-20 ml H20-3 ml concentrated HC1. Radioactive tracer (co60 or co5' or Ag'lO, each having a radio-chemical purity of greater than 99 pct) was deposited onto the prepared surface either dropwise with evaporation to dryness of the solution containing the tracer (0.5 N HC1 solution for the co60 and co5' and 0.6 N HNO3 solution for the A"'), by electroplating, or by evaporation from a tantalum or tungsten filament in an evacuated bell jar. The amount of deposited cobalt was varied from many atomic layers of cobalt containing the co60 to approximately one co5' atom per lo6 surface atoms of silver. This large variation in amount of deposited cobalt yielded information about both the influence of a thick-source layer of tracer and solubility effects on the NSE. Such variations were possible because of the large differences in half-lives,

Jan 1, 1969

By N. J. Grant, Per Knudsen, J. T. Blucher

The fatigue behavior of three SAP alloys was studied in ternzs of strain rate and temperature, at high strains. The k values in the modified Manson-Coffin equation, Nk4 = C, were less than 0.5 under all test conditions, and change with strain amplitude for the lower-oxide alloys at about 2 pct strain. Lowest k values were near 0.25. Strain rate had no effect on life at 80 F, but had an increasingly greater effect with increasing temperature above 500". Life decreased with decreasing strain rate, above 500"F, and with increasing temperature. Ductility at fracture in a tension test was indicated to be an important factor in determining 1ife in these big+-strain tests with the SAP alloys. INEVITABLY, in the course of mechanical tests at elevated temperatures, particularly if significant time at temperature is involved, there are large changes in structure; these changes make it difficult to relate behavior patterns over ranges of temperature or strain rates at high temperatures. Such changes are to be expetted in low cycle fatigue at low strain rates and high temperatures. Accordingly, it was of great interest to examine the low cycle fatigue behavior of SAP / an aluminum oxide dispersion-strengthened aluminum, a type of alloy which had shown unusual structure stability to temperatures as high as 1000" to 1150°F and resisted recrys-tallization essentially to the melting temperature.'j3 Since the matrix is pure aluminum, there are no complications of averaging, agglomeration, or phase solution. It was also desirable to check the Manson-Coffin equation4?' for the SAP alloys, namely N~E~ = , where ep is the total plastic strain amplitude, k and C are constants, and N is the number of cycles to failure. Here, too, was an opportunity to check the roles of temperature and strain rate with a very stable material. Tavernelli and coffin6 had concluded that k had a value of about 0.5 for many alloys and C was equal to ~/2, where E is the fracture ductility determined from a static tension test. The results were obtained from low-temperature tests where creep and diffusion processes are unimportant. Manson7 found k = 0.6 fitted his data reasonably well; however, in later analyses of a large amount of low cycle fatigue data generated at room temperat~re@"~ he found k to vary from 0.6 for short lives to 0.21 for long-life fatigue tests. In the latter studies,89g Manson separated the total strain range into elastic and plastic components when he found that k was influenced by the nature of the strain. The use of EL (total strain) instead of EP (total plastic strain)4'5 makes a difference in the resultant k value. The ratio of changes with temperature, strain rate, and strain; further, there are the problems in the determination of the elastic strain. Based on these considerations, and the improved fit of points in a plot of by Wells and Sullivan,' is also utilized in these studies. Anderson and wahl,14 using commercial 1100 aluminum, and Blucher and Grant,15 using 99.99 pct pure aluminum, found an increase in life with increasing test temperature. Anderson and Wahl were the first to report low cycle fatigue results from SAP materials. With increasing temperature, the role of strain rate becomes more important. In this regard, care must be exercised to differentiate between frequency (wherein strain rate may vary from zero to a maximum in each cycle, sinusoidally, for example), and constant strain rate, as used in the present study, in a saw-tooth type cycle; in the latter case, the frequency is not specified but can easily be calculated from the strain and strain rate data. It has generally been found that life in low cycle fatigue tests decreases with decreasing frequency16 or with decreasing strain rate at elevated temperatures.15 Coffin,17 reviewing Eckel's work,16 also reported that k increased with decreasing frequency for acid lead, yielding values from 4.0 at a frequency fo 6.6 cycles Per day to 1-46 at a frequency of 7440 cycles per day; the value of k decreased to 0.58 at a frequency of 2.38 x lo6 cycles per day. EXPERIMENTAL PROCEDURE Three SAP alloys, of two nominal compositions, were tested. Alcoa supplied XAP 005 as 2-in.-diam extruded bar, of nominal composition A1-7 wt pct A1203. The Danish Atomic Energy Commission supplied SAP 930 (A1-7 wt ~ct Ala3) and SAP 865 (A1-13 wt pct Al&) manufactured by Swiss Aluminium Ltd., in the form Of $-in.-diam extruded rod. Metallographic comparison of the structures of XAP 005 and SAP 930 showed the former to have a more uniform oxide distribution. Button-head specimens were machined in the longitudinal direction of the bar with 0.4 in. gage length by 0.2 in. diameter, with a fillet radius of j-B in. After machining, the specimens were electropolished in a 1 to 4 mixture of perchloric acid to methanol to remove all machining marks. All test bars were in the as-extruded condition. The fatigue tests were performed on a hydraulically activated, axial strain machine, with complete reversal of strain.15 Test conditions were:

Jan 1, 1969

By A. C. Fieldner

THE older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer, I who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter "g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 5, 1925

By A. H. Glenn, J. E. Graham

Oil operators engaged in drilling on the Continental Shelf of Louisiana and Texas are in agreement that adverse weather and wave action are two of the greatest hazards to the safety and efficiency of their work. It was ami-pated when the offshore operations commenced that such would be the case, and experience to date has verified this assumption. Because atmospheric conditions and wave action involve tremendous amounts of energy it is highly unlikely that it will be possible to control any but the most localized weather and wave phenomena within the foreseeable future. Thus. as long as the offshore operations involve the movement of small craft and barges over exposed waters, and the transfer of personnel and heavy equipment from these craft to either fixed structures or larger craft at close quarters, the weather and wave problem will remain. Taking into consideration the persistence of the wave and weather problem and the improbability of achieving a direct solution, the Humble Oil & Refining Company, in planning its offshore campaign investigated the possibility of forecasting wave and weather conditions in order to provide warnings of dangerous conditions and increase efficiency in day-to-day planning of work. It was recognized that predictions of wave and weather conditions based on meteorology and oceanography, both geophysical sciences, are not 100 per cent accurate and application of forecasts in the offshore work was dependent on whether they provided information which was sufficiently greater in accuracy than the layman's guess to be worth the expenditure involved. During World War 11. meteorology and oceanography were used with success in reducing danger resulting from environmental conditions and increasing efficiency of operations exposed to the elements. This success was partially the result. of improvement in the scientific techniques involved and the procurement and distribution of observational data, and partially due to the large scope of the military operations which meant that a reduction of losses of a relatively small percentage of the total cost amounted to a large figure expressed in terms of dollars. Since the offshore drilling involves an extremely large financial investment, it was considered that the experience of the Armed Services in successfully employing meteorology and oceanography might be duplicated in the oil industry. In addition. the oil industry's successful experience in utilizing seismology, geology, and terrestrial magnetism; all geophysical sciences, indicated that meteorology and oceanography, also of the family of geophysical sciences and sharing their scientific assets and liabilities, might be profitably put to use. Since the immediate problem involving the sciences of meteorology and oceanography in the offshore campaign is wave action, a program was inaugurated within the Humble Oil & Refining Company during June 1947. the purpose of which was to ascertain the applicability and limitations of wave forecasting in the offshore campaign. A summary of the effective wave forecasting techniques developed during the war was prepared in the form of a forecasting manual for the Continental Shelf off Grand Isle, Louisiana, by Bates and Glenn. After completion of this manual, experimental forecasts were prepared daily over a two-month period by Graham and Thompson to determine the accuracy of the forecasts. It was considered that the accuracy of the experimental forecasts justified a more extensive test under actual operating conditions in the offshore work and the firm of A. H. Glenn and Associates was set up under the sponsorship of the Humble Oil & Refining Company to work with the Humble Grand Isle District in providing forecasts of wave and weather conditions over a one-year period. This paper discusses the service now provided to the Grand Isle District, its applicability and limitations. TYPE OF FORECASTS REQUIRED It was apparent before the commence-mence of the forecasting service that a specialized type of forecast was required. Many of the weather elements of interest to the general public, such as rain and temperature, are of minor concern to offshore operators. On the other hand, such elements as wave height and wind speed and direction are of great concern in the offshore operations since variations in wave height of a few feet in the critical range divide safe from hazardous working conditions. To be of utility. a forecasting service for the offshore work must provide detailed forecasts of the elements which affect the operation. With this in mind, it was decided that forecasts would include the following information: average wave heights to the nearest foot, wind speeds within a range of approximately 5 miles per hour, and wind directions within 221 degrees. Since the procedure for forecasting these elements involves thorough analysis of weather data, it was decided to include a generalized forecast of weather conditions such as rain and cloud cover, although these are of secondary importance.

Jan 1, 1949

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but cannot be obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Co. in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1973

[*E. O'C. Acker '86 Jinzoc Adachl '88 T. H. Aldrich '96 *Truman H. Aldrich '78 Walter H. Aldridge '89 *Anson W. Allen '87 John H. Allen '84 *Thomas Andrews '94 *William R. Analeby '90]

Jan 1, 1946

By Roy E. Gilbert

IN what ways can conventional geophysical methods be used in the search for quartz-sulphide veins covered by several feet of overburden? The New Park Mining Co., in search of an answer to this question, empirically tested simple geochemical, electrical, and magnetic methods over known ore bodies and geologic structures. Geochemical methods were the only ones found to be applicable to direct ore search. Indirect uses were found for electrical and magnetic tests. Experiments were conducted in the southeastern part of the Park City mining district. Ore in this part of the district is found principally in steeply dipping veins which are localized along faults and fractures that cut Paleozoic sediments and quartz diorite intrusives. Extensive soil cover effiectively hides both veins and country rock. The type of vein most likely to

Jan 1, 1953

By E. H. Crabtree, W. F. Netezband

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,' or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9' per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By R. D. Pehlke, J. V. Gluck

A study was made of' the effects of up to five additional solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450" to 650°C. The experimental measurements were made in a multielectrode galvanic cell apparatus employing fused LiCl-KCl as the electrolyte. The solute additions included indium, lead, tin, cadmium, copper, silver, antimony, or gold. A range of positice and negative interactiotls with zinc was covered. The experinzer~tal observations were cowlpared with the activity coefficients calculated usitlg either Wagner's first-order Taylor series rnodel or a proposed second-order solution itrteraction model. hi general, the truncated first-order Taylor series proposed by Wagner gaue good results for "dilute" solutions (XBi > 0.90) contaitzing up to six solutes. The second-order model, which includes a second-order cross-interaction term, produced a slight improvement in predictions for solutions with XZn = 0.015 and a significant improvement for solutions with XZn = 0.050 hear the limit of Henry's law region). Seveval of the quaternary solutions studied contained a total solute content of 0.215 mole fraction, and fairly good success was achieved in predicting the activity coefficient 01- zinc. ThE study of thermodynamic interactions between dilute solutes in liquid metallic solutions has occasioned much recent interest. It is useful to recall in this respect that Wagner's well-known expression for the activity coefficient' is a practical application of the problem of representing a given function, i .e., In ?, by means of a sequence of polynomials. No specific physical model of a solution is involved in its use. As suggested by Wagner, a Taylor Series is used to expand In ? about a point of infinite dilution with respect to all solutes. The partial differential coefficients of the series have been termed "interaction parameters". Various authors'-6 have proposed formalisms for parameters, the definitions being designed to meet some specific experimental or physical condition. A usual assumption is that terms above first-order in the Taylor Series may be neglected. In that case, the logarithm of the activity coefficient is expressed as a linear function of solute concentrations. The resulting expression is presumed valid for any number of additional solutes as long as the solution can be regarded as "dilute". This assumption can be termed "the hypothesis of additivity". However, experimental tests of that hypothesis for quaternary or higher-order solutions have been extremely limited. Primarily such tests have been confined to studies of effects of added metallic elements on either the activity of carbon or the solubility of gases in liquid iron.7-13 The only known previous study of an all-metal system is the limited work of Okajima and pehlke14 on the effects of multiple solute additions on the activity of cadmium in liquid lead. The present investigation is a portion of the work to determine the effects of various solute additions on the activity of zinc in dilute solution with molten bismuth in the range 450" to 650C It was shown for such ternary solutions that second-order Taylor Series terms could be evaluated at the same time as first-order terms, with no additional experimentation required. A second-order solution model was described which, under certain conditions, is a rigorous representation of solute activity in a ternary solution. (In the sense employed in this paper, the term "model", as distinguished from "equation", is taken to mean an empirical correlation or formalism, but not a hypothetical physical system per se.) Presumably such a model could be extended to produce a better representation of In ? in solutions of even higher order. The feasibility of a generalized Taylor Series approach to solution interactions and inclusion of second-order terms also has been discussed recently by Lupis and Elliott in independent work concurrent with the present investigation. In addition, they discussed empirical means of estimating certain second -order coefficients.17 The utility of such solution models rests on the ability of a truncated series to represent adequately the experimental facts in multicomponent solutions. Questions that arise include: Do the second-order terms really make a significant contribution? How far away from "dilute" solution may such models be applied? Are the types and varieties of the additional solutes important? among others. In order to provide some answers to these questions, an experimental study was made of the effects of two or more additional solutes on the activity of zinc in dilute solution with molten bismuth. Comparisons were then made with calculated activity coefficients obtained using the previously determined ternary interaction parameters. INTERACTION MODELS As an example of the approach to defining activities in multicomponent solutions, consider the Taylor Series expansion for a quaternary system, i.e., three dilute solutes. Writing terms through second order, the result is:''

Jan 1, 1968

Jan 1, 1947

By C. W. Goodale

THE motives behind the organization of the Bureau of Safety were twofold. First, there was the policy of the company toward its employees, which was one of fairness and consideration for their welfare and which entails the prevention of injuries; second, in order to prevent injuries, a study of their causes was essential, and this study could be made only by a thorough systematic classification of accidents, which required a special department to form and carry out the plans. The Bureau of Safety was organized to begin operation Jan. 1, 1914, but practically all of the first year was spent in collecting data, making plans, etc. This department is semi-independent of others and reports directly to the president and general manager. It consists of the president of the company and the managers of the following departments: Mines, Washoe Reduction Works, Great Falls Reduction Works, Coal Department, Lumber Department, B. A. & P. railway, and the chairman of the Bureau of Safety. Working under this group is the General Safety Committee consisting of the manager of mines, as chairman, the general superintendent, two assistant general superintendents, and the heads of the following departments: mechanical, geological, purchasing, sampling works, and framing plant, as well as the safety engineer. Operating under the General Safety Committee are the group safety committees, consisting of the Anaconda group of mines, Boston & Montana group of mines, zinc group of mines,.Washoe reduction works at Anaconda, B. & M. reduction works at Great Falls, coal department, lumber department and the B. A. & P. railway. Each of these group safety committees was in charge of the superintendent or manager of the group represented and the committee consisted of the foremen of the mines or works that the committee served, as well as the safety engineer.

Jan 2, 1922

By S. T. Yuster

An analysis has been made of the factors responsible for tilted fluid contacts in petroleum reservoirs. The factors are static and dynamic with the former being controlled by those variables responsible for the capillary rise of fluids, and the latter include rate of formation tilt and hydraulic circulation. The explanation that rate of formation tilt may be responsible for tilted contacts appears untenable. The role of some of these factors in the migration, fractionation. accumulation and possibly the prospecting for oil is indicated. INTRODUCTION While it is generally considered that the segregation of gas, oil, and water in a petroleum reservoir results in approximately horizontal planes separating these phases. there are factor; which modify this simplified picture to a very great extent. Some of these factors are static. and the departure of the fluid interfaces from horizontal may represent a static equlibriun. Some of these factors may be dynamic and the interface positions may be non-equilibrium and represent a steady .state condition. Of course combinations of these two situations may also exist. The reasons most commonly given for this behavior are hydraulic circulation of fluids, change in character of the formation, and a rate of tilt of the formations more rapid than the rate at which the fluids may re-establish an equilibrium. Russell's Principles of Petroleum Geology' contains an extensive discussion of tilted fluid interfaces and their importance in the migration and accumulation of petroleum. Russell cites examples of tilted water tables at Lance Creek, Wyo.; Rock River, Wyo.: Cut Bank. Mont.; Cushing, Okla.: and Graham; Okla. Also given was the Wasson Field of West Texas which has saucer shaped oil-water and gas-oil interfaces with the saucer being deeper in the case of the oil-water contact. The Bradford Field in Pennsylvania has a tilted water table. San Ardo. Coalinga None and some other California field.; have tilled contacts. A recent paper by King Hubbert discuses the effect of hydraulic circulation of the water underlying the oil in a given stratun and it- implications in the accumulation of and drilling for the oil. The foregoing would indicate that tilted fluid interfaces are not uncommon and that it would be of importance to underbtand the forces which are responsible. Further. it would be of interest to examine certain idealized models of situations which may cause tilting with the thought in mind of deriving relatinnships between the important variables. These relationships may only hold exactly for the model* assumed but the results may apply semi-quantitatively to actual formations and at least indicate trends. The discussion will be divided into the effect of static factors and the effect of dynamic factors. STATIC FACTORS It has already been mentioned that one reason given for tilted contacts is a variation in formation properties. Specifically this is a change in the pore size of the formation capilaries. If the internal surface of the reservoir is preferetially wet by water, capillarity will cause the water 10 rise to a greater extent above the free water table in a small capillary than in a large one. Consequently the water-oil contact will be higher in the lower permeability sands than in the higher permeability sand.;. The free water table may be defined as the position the oil-water interface would take if capillarity were absent. Since the phenomenon is the capillary rise of water in an oil environment, a derivation of this shold give a relationship between the variables. Fig. 1 is an idealized model of the situation with a uniform bore circular capillary ubstitttting for the tortuous non.circular formation pore. The upward force.; on the column of water will be equated to the forces downward to give the equilibrium situation. forces upward = force downward where r is the radius of the capillary in ceritimetera. a is the interfacial ten4on oil-water in dynes per centimeter, 0 is the

Jan 1, 1953

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By C. N. Garman

Homestake-New Mexico Partners operate a 750-tpd carbonate leach uranium concentrate mill near Grants, N.M. The highly mineralized water available as process water leaves much to be desired. The 628 ppm as CaCO 3 makes the use of raw water very troublesome in pipes and on filter cloths. However, the residual sodium carbonate in the final filter cake going to tails makes an ideal softening agent. To take advantage of this fact, all makeup water used in the mill is first used as tailing slurry dilution water and comes to the mill from the tailings pond. The 5-acre tailings pond serves as a thickener and 100 to 150 gpm of nearly clear solution is decanted to a pump to be returned to the mill. Since this tailings water has small quantities of uranium in the solution an ion exchange scavenger unit was installed to remove as much uranium as possible. The ion exchange raffinate is then used as final filter wash ahead of the tailings slurrying step. In spite of the large settling area this return water is not clean enough for ion exchange feed. The solids present are very fine and composed of approximately 15 pct (by weight) burnable carbonaceous material common to the sandstone uranium ores in the area, 40 pct SiOz plus 45 pct CaC03. Laboratory work showed that this material responds very well to flotation. Before deciding to use flotation, various clarifying systems such as pressure leaf filters, sand filters, and continuous vacuum pre-coat filters, were considered. Each of these could have solved the problem but with much more operating labor, more reagents and greater installation costs than the flotation step. About 100 to 150 gpm of fouled water is fed to two 66-in. Fagergren cells, in series. Reagents used at the beginning were Arquad 2HT75 and Arquad C50, at the rate of about 1% lb per 8-hr shift, or about 0.0053 lb each per ton of ore. This did not completely remove the solids but does an acceptable job. Approximately 75 pct of the slimes are a size that can be caught on a 41-Whatman Paper are removed. Removal of these slimes also allows much better settling of the coarse nonfloatable material. Advantage is also taken of this fact in a small settling tank ahead of precipitation. Removal of this amount of the slimes makes the ion t:xchange feasible. PREGNANT SOLUTION CIRCUIT The carbonate? leach-caustic precipitation method of uranium concertration does not provide for any process purification step ahead of precipitation. Therefore, any fine solids getting into the pregnant solution through the filter cloth show up in the final concentrate. This, of course, lowers the grade, and, at times, the slimy nature of these very fine solids rendered final filtration of the concentrate difficult if not impossible At Homestake-New Mexico Partners a 75-ft thickener was available for gravity clarification of 100 to 120 gpm of this pregnant solution. However this did not sufficiently remove the slimes. Laboratory investigation of the whole range of flocculants that were suggested by literature, salesmen, and friends failed to turn up anything of consequence. A continuous vacuum pre-coat filter would do the job and was investigated. The capital cost and the operating labor and materials made this a last chance choice. Following work done in the metallurgical laboratory on the tailings return water, it was found that some changes in the reagent strengths and combinations made a very definite decrease in the solids in the pregnant solution. Concentrate grade improved about 5 pct anti the final product after drying had an appreciably greater bulk density. Compared to a cost of about 2.2e per ton for pre-coat filter opelation for cleaning just one circuit, flotation costs less than 1.0 per ton of ore for cleaning two circuits. While a pre-coat filter would do a more thorough job, the flotation does all that is required for either circuit. Gravity causes the froth produced to run back into the leach circuit. This does not appear to result in a build-up of objectionable slime. No extra manpower is required; the operators in the separate areas can observe the operation of the cells and mix the small quantities of reagents as needed. Normally the 66-in. Fagergren cell requires 15 hp per cell, but this very dilute slurry needs only 10 hp for both cells. Originally, a combination of the two Arquads mentioned previously served as frothers and promoters. As further testing

Jan 1, 1962

Commonwealth of Pennsylvania, Department of Internal Affairs, Topographic and Geologic Survey, Harrisburg, Pa George H. Ashley, State Geologist All available printed Bulletins may be obtained through the Commonwealth of Pennsylvania, Division of Documents. Where a price has been set on the publication, checks should be made out to the Commonwealth of Pennsylvania. A Syllabus of Pennsylvania Geology and Mineral Resources has recently been published by the Survey as Bulletin G1, and consists of a general survey of the state An appendix of this bulletin also gives a complete bibliography of Survey publications It will be sent upon request. The State Geological Survey has gone through several phases and reorganizations, publications of three of them being numerous and important A fire, in 1927, destroyed supplies of many of the papers of the present Survey. Available bulletins of the present Survey are: Bulletin M6: Bituminous coal fields of Pennsylvania, in 4 parts available as follows: pt 1, General description of coal, 50 cents; 3, Bituminous coal resources, 25 cents, 4, Analyses of bituminous coals, 25 cents Bulletin M10, Fire clays of Pennsylvania; Mll, Molding sands of Pennsylvania; M12, Anthracite culm and silt (1928); M13, Feldspar in Pennsylvania; M14, Magnetite deposits of French Creek (1931); County Report C1, Adams County, pt 1, Geology and geography (in press), County Report C2, Geology and mineral resources of Greene County (in press); Topographic and Geologic Atlas A5, New Castle Quadrangle (1929), $1; Topographic and Geologic Atlas A27, Pittsburgh Quadrangle (1929), $1; Topographic and Geologic Atlas A168, Lancaster Quadrangle (1930), $1. The present Survey has also issued a number of short mimeo¬graphed bulletins any of which will be sent upon request Briefly they are: No. 15, Mineral resources of Pennsylvania; 20, Iron ores; 28, Magnesite; 40, White clay deposits, Monroe County; 45, White clay deposits, central Pennsylvania; 47, Manganese, Eastern Pennsylvania, 48, Pyrite from bituminous coal mines; 59, Bog

Jan 1, 1933

By H. F. Porter

MUCH has been written relative to the errors involved in the use of a galvanometer for measuring thermocouple electromotive forces. In general, it may be said that accuracy with a galvanometer is secured only at the sacrifice of durability, unless manual adjustment is made in the operation of the instrument to overcome the errors of resistance. and resistance changes. The pyrovolter and the potentiometer both require manual adjustment for every reading, readings being taken on a "null" method. To the end that some of these balances may be eliminated and only an occasional balance be made as a check reading, the "continuously deflecting pyrovolter" was developed. Essentially, the operation of the continuously deflecting pyrovolter is to determine the resistance of the thermocouple circuit, though its value is not noted or indicated, then throwing in series with the thermocouple sufficient resistance to bring the sum up to some standard value for which the indications of the galvanometer will be correct. This result may, however, be accomplished in a somewhat simpler manner, for which general method patents are now in the course of application. If we devise a galvanometer circuit so that by means of a simple adjustment the resistance of the entire circuit will be rendered equal to some constant predetermined value, we may rely on the galvanometer to give correct e.m.f. indications (assuming that the errors of temperature resistance coefficient and cold junction have been properly allowed for), and will indicate temperature continuously where the e.m.f. measured is developed by a thermocouple.

Jan 9, 1919