Search Documents

By Leonard P. Skolnick

PROPERTIES of materials containing a hard con-stituent dispersed in a metallic matrix are dependent on the distribution of the hard phase.'-' The grain growth of titanium carbide in liquid nickel was studied in order to understand microstructural development in this and similar systems. Smith" has examined the influence of surface energy on the distribution of phases in alloys. The grain growth of tungsten carbide in cobalt has been the subject of many conflicting theories. Those prior to 1950 have been summarized by Goetzel.' Recently, Gurland and Norton3 and Gurland8 have indicated that growth occurs primarily by diffusion through the liquid phase in order to lower the inter-facial energy between the carbide and the liquid metal. In the development of the Ti-C-Ni ternary phase diagram, Stover and Wulff9 have shown that both eutectiferous dendritic titanium carbide, and primary titanium carbide which had developed crystals of cubic symmetry, were rounded by heating below the solidus, and that if primary carbide was already present the typical eutectic decomposition products were not formed. Experimental Procedure The infiltration technique was used to study the grain growth of titanium carbide in nickel. In contrast to sintering, infiltration more readily assures uniform dispersion of the two phases, and the problems associated with mixing by milling; i.e., mill contamination, breakdown of original carbide size in the operation, development of interfering surface films, etc., are avoided. In addition, the complicating effect of densification by shrinkage is eliminated. The titanium carbides used were commercial grades. Their chemical analyses, size distributions and shapes are summarized in Table I. Size analysis was conducted by microscopic count on a minimum

Jan 1, 1958

By C. L. T. Edwards

IN the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on 100 per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blast-furnace charge as good iron as that made without scrap-made with straight ore?" This question may be answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on 100 per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. OPERATION WITH 100 PER CENT STEEL SCRAP During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a 100 per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when l00 per cent steel turnings were charged. Except for occasional charges of nickel scale as an "extra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore-ore and scrap-operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from i00 per cent scrap to the regular burden, the charge hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap charge. The furnace employed had a hearth 16 ft. 0 in., bosh 22 ft. 0 in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter ¾ in., bosh angle 73° 27' and a Baker-Neuman top, with gas-engine blowers. Analyses Range of Material Charged Gravel: Si02, 64.40 to .7o.54 per cent; A1203,3-52 to 4.58; CaO, 7.27 to 9.49; M90, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83.

Jan 1, 1941

By H. M. Merry

The graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts shown in Pig. 3, and the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution, percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required. GRaphic Presentation . Close analysis is necessary of a daily operation involving such a number of factors, the relation and influence of which may be of great importance in the treatment scheme. When the analysis is made from a numerical tabulation, the chance for one or more obscure, but perhaps important, factors to escape notice is considerable, therefore the need for an accurate, readily digestible presentation of metallurgical data is obvious.. Graphic records of milling operations are frequently used, but owing to the wide range of magnitude and values, and the number of factors involved, the customary practice of assigning different values to the same ordinates, as in Fig. 1, results in a complex and intricate record which makes little appeal to a busy operating official. The methods shown in Figs. 2 and 3 are devised to display such data in a clear and legible manner, without confusion.

Jan 1, 1920

By G. Campbell

The paper by M. Lonoff looks at the importance of byproduct prices on copper production. The paper develops several interesting points on this topic, but there are some points in the theoretical discussion that could use further development. A couple of these theoretical topics will be considered here using the paper's framework of assumptions without concern about how realistic the assumptions are for the copper industry. Lonoff’s theoretical model is based on a static, homogenous world where all copper/byproduct deposits are identical, and these deposits are the main source of these metals. Due to the importance of the byproducts to the production decision, the term coproducts will be substituted for the term byproducts to reflect more accurately this condition. The conclusion is drawn that a rise in coproduct prices necessitates a decrease in copper prices because copper production is increased as a consequence of increased coproduct production. The observation that real world behavior does not always follow this pattern is dismissed as "speculation." However, it can be easily shown that within this simple framework market forces might create the observed behavior. The key question to be answered is what causes coproduct prices to rise. Three possible cases will be used as illustrations. The first case is the one implicity assumed by Lonoff. Here, the demand for coproducts increases at all prices (an outward parallel shift of the demand curve) with the demand for copper remaining constant. As reported in the paper, the results are higher coproduct prices, an increase in coproduct production, and lower copper prices due to the resulting increase in copper production. The second case is when the supply of coproducts are constrained-leading to higher market prices. Copper production, as required by the simple model, is also reduced which

Jan 1, 1984

By Howbert Van Dyne

THE Presidio mine of The American Metal Co. of Texas is situated 45 miles south of Marfa, Texas, a town on the Southern Pacific R. R., and lies approximately 20 miles north of the Mexican border. Communication with the railroad is maintained over a state highway. All supplies for mine and mill are hauled in by truck from Marfa and precipitates and concentrates are freighted to the railroad by the same means and shipped to Selby and El Paso, respectively. The mill is at the town of Shafter, 1 mile from the mine and at approximately 350 ft. lower elevation. The ore is conveyed to it by an aerial tramway which requires practically no power on account of the difference in elevation. The mill is a countercurrent decantation cyanide and gravity concentrating plant of 200 tons daily capacity. Coarse and fine crushing are done at the mill. Two near-by shallow wells in the bed of Cibolo Creek furnish an abundance of water. Power is generated for the mill and town by a Diesel engine plant.

Jan 1, 1930

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10 to Aug. 10, 1915: Members ALBERTSON, MAURICE MERTON, Mine Surveyor, Mining Corporation of Canada, Cobalt, Ont., Canada. ARMSTRONG, GEORGE CHANDLER Mgr., Indian Refining Co., Lawrenceville, Ill. BARBER, MAX HAYDEN, Min. Engr Supt., Crosby Mine, Nashwauk, Minn. BARNESON, JOHN Merchant, 310 Sansome St., San Francisco, Cal. BENSEL, JOHN A., Cons. Engr 111 Broadway, New York, N. Y . BORGESON, ANSHELM CYRUS, fin. Engr Shenango Mule, Chisholm, Minn. BROOKS, CHARLES PETER, Min. Engr 228 Dooly Bldg., Salt, Lake City, Utah. BROWN, FRANK HAROLD, U'011',. Min. Engr., Federal Co., Inc., 50 Broad St., New York, N. Y. CLARK, DOUGLAS Kellogg, Idaho.

Jan 9, 1915

Taking the Long View THE present international situation has serious implications for this nation. The possibility of total war is no more appalling than the threat of making the United States permanently into an armed camp. A period of ten years under such conditions could mean a Communist victory without firing a shot-if the present trend toward statism is allowed to continue. As individual citizens and as members of the mining profession we have the power to oppose the march toward socialism. We must not adopt shortsighted policies dictated by self-interest, but must endeavor to size up the situation as a whole and act according to what will be best in the national interest. The economic picture for the metal mining industry under present emergency conditions is apparently bright. Demand for metals exceeds supply. But there is danger that fluctuating prices will bring Government regulation. Care must be exercised in our pricing policies, or the calamity of Government intervention will be inevitable. President Truman's "loophole" reference to percentage depletion early in the year caused a brief flurry of excitement, but now that the immediate threat is over the industry has lapsed into sommolence on this subject. Special tax privileges accorded the mining industry because of inherent risks should be guarded by a continuing propaganda campaign to educate Congress and the public. If this is not done we may find ourselves losing the necessary tax protection which we now possess by a capricious act of legislation. Stockpiling minerals from abroad certainly lengthens the life of our own mineral resources. The present consumer demand for the base metals indicates foreign sources of supply for stockpiling. However, this is only one facet of the problem. For strategic military reasons it is necessary that the United States have quick sources of all minerals within our national boundaries. Undeveloped mineral deposits do not meet this need so that where it is possible to encourage our own mineral development by stockpile purchases, it should be done. A need exists for an overall controlling agency that would make purchases for the stockpile according to military necessity, current metal market conditions, and so as to strengthen the mining industry. In the course of the history of the United States we have been engulfed in several wars by the necessity of protecting our economic rights abroad trading privileges-and also because of moral obligations. Disregarding the moral side, it is difficult to reconcile fighting wars to protect world freedom of trade when in peacetime we attempt to restrain such trade by tariff barriers. When it comes to accepting subsidies from the Government in one form or another it is difficult to overlook the immediate personal gains and see in the future that where the Government lays out capital it becomes a partner in the business and not a silent one. It is apparent that hope for the traditional American way of life cannot be bought without some self-sacrifice; and we cannot wait for the other fellow to start it because it is the responsibility of each individual citizen. By taking the long view our course should be apparent and not diverge sharply from our own personal benefit.

Jan 10, 1950

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By Abdul-Fattah K. Kaddou, P. C. Rosenthal

THE authors have studied the problem of temper brittleness in steel1 employing an internal friction method. The specimens are in the form of wire, 14 B and S gage (0.064 in diam), 6 in. long. It was very desirable to have an apparatus to test the wire specimens for temper brittleness without making standard notched-bar Izod or Charpy impact tests. Such a device would have two favorable advantages: the first is that no standard impact specimen would be necessary, thus saving time and labor; the second is that there would be a direct correlation with internal friction results, thus eliminating the size factor if standard impact specimens had to be used. A search was made without result to find a commercial apparatus for this purpose. The literature was surveyed to investigate if such a test had been utilized. No such work has been reported in the literature; however, zapffe2 has described an apparatus used for testing for hydrogen embrittlement in

Jan 1, 1961

By R. D. Coleman, A. E. McIlhinney, C. E. Capes

Problems of unstable operation in continuous balling circuits may be traced to the random generation of seed agglomerates. This has been verified during the continuous operation of a laboratory balling drum with internal recycle described previously by the authors. The cyclical behavior of a balling circuit was also investigated using a simple numerical computer model. Changes are suggested in the design of balling equipment to improve stability.

Jan 1, 1976

By B. Hyatt, E. Klokholm

The reesistivity of Cu-Pd alloys of 9.6 to 29 pct Pd alloys was measured after plastic deformzation in tension. For all compositions a continzting decrease in resistivity with increasing plastic strain was observed. By comparison with the results of Damask on a brass ad Cu3Au, it was deduced that these anonzalous decreases in resistivity are due to the decrease in short-vunge order caused by cold work. An anomalous decrease in the resistivity of cold-worked CU-Pd alloys was first reported by Jaumot and Sawatzky.&apos; They observed decreases in the electrical resistivity when disordered Cu-Pd alloys drawing at room temperature. Recently, a similar anomaly was reported by Aarts and Houston-Mac-Mi1lan2 in Ag-Pd alloys containing 10 to 45 pct Pd. The plastic deformation in this case was produced by tensile strain at liquid-nitrogen temperatures. For AE-Pd alloys the relative resistivity change becomes positive for tensile strains of about 20 pct.

Jan 1, 1960

By John Blandy

EVERY new mining district has had its own peculiar experiences in inventing and experimenting upon new methods for the various operations of mining, and more particularly in the processes of crushing and dressing ores. As a matter of course, during this period many old things have been reinvented, patented, and cast aside, there to remain until at a future day other geniuses shall bring them forth again as new. In this respect the Copper Region of Michigan has not been behind other mining centres, and probably in no other part of the country has more money been expended in devising new machines and improvements upon old ones for the crushing of the rock. The appliances for washing the sand have not been so varied, simply for the reason that, having but one mineral, or rather metal, of high specific gravity to separate from rock material which varies but little in its character in any one mine, it requires much less care than is necessary in most mining centres of the world. At the beginning of operations in that district most of the work was in the control of Cornish miners, who introduced the simplest of Cornish mills, namely, wooden stem pestles, with wooden shafts and cams. These were well suited to the small mines, and particularly to the limited means of transporting more expensive machinery. As these facilities improved, they were enabled to change to iron, and to vary their patterns of rods, shafts, cams, and mortars. The most approved pattern, finally obtained, is the square or round stem, with collar adjustable by means of keys. In its present form it is a bar of cold rolled shafting, an eye in the top, an adjustable collar with key-plate and keys, the head and a shoe of chilled iron. The stem is fitted into the head by a slight taper. The battery has heretofore been of wood, lined with chilled cast plates, and bed-plate of the same, but within the past year the California pattern has been introduced. The screens are of sheet-steel, drilled with 16 holes to the inch. During this period of trial and gradual improvement in the pestle stamps, in the years 1855-6, the Ball steam-stamps were intro¬duced, and after years of labor and expense, have been made the most efficient and powerful machines ever yet used for the purpose. It is ostensibly the Nasmyth steam-hammer, and yet the

Jan 1, 1874

By E. Gybbon Spilsbury

THE introduction of underground machinery in mines, and especially the invention of the rock drill, called attention to the necessity for some motive power to drive them. The use of steam generators underground is as a general thing inadmissible, owing to the, difficulties of ventilation and the transportation of fuel, and the great loss of power by condensation in the pipes, when surface generators are used, added to the inconvenience of getting rid of the exhaust steam, has precluded the direct use of steam for this class of machinery. Water as a power has with very few exceptions proved a failure, owing to its weight and incompressibility, and there-fore the attention of mining engineers has very naturally turned to the use of compressed air. This agent not only answers all the requirements for power, but has the double advantage of greatly assisting in thoroughly ventilating remote workings, and in cooling the underground atmosphere. It is therefore clear that the successful introduction of underground machinery is dependent on the economical production of good and efficient air-compressing machinery. Although many improvements have of late years been introduced in this class of machines, the most of them are open to serious objections, the chief of which are the very small duty they perform for the power expended, and their great expense, due to the complexity of their construction. This latter fault is the chief reason why the introduction of rock drills and other underground engines is so limited, as comparatively few mines can afford to expend the required capital for the installation of a complete compressing plant. But with the introduction of a cheap and effective compressor, there is no doubt that power drills will become as generally used in mines as the hand drills are now. The great excess of power required in most machines to compress air over that given out again by the use of the air thus compressed (amounting as it does in most cases to sixty per cent.) is well known to all mining engineers. Of course a portion of this loss is due to the friction of the air through the pipes, and will always occur however effective the machine used maybe, but the chief cause -of the

Jan 1, 1880

By R. L. Perrine

This paper shows how stability theory can be used to optimize solvent recovery of oil. Application of the theory leads to definition of the limiting conditions required for stable displacement to occur. One of these conditions is that the size of a solvent "slug" must at least equal a prescribed minimum. The criteria to be satisfied are miscibil-ity and stability. Stability implies that no viscous fingering will occur and that mixing will be caused only by a dispersion process. Miscibility implies that complete recovery will be obtained from the swept regions. Thus, for any specified set of reservoir conditions, an optimum use of solvent is defined. INTRODUCTION The early outlook for solvent flooding as a means to increase oil recovery was very favorable. Some laboratory results indicated that a "slug" containing perhaps 2 to 3 per cent of a hydrocarbon pore volume could be successful. However, other data suggested as much as 30 per cent would be required. The difference is of considerable economic importance. A theoretical explanation for these divergent results has been advanced by the author.1,2 Stability theory defines conditions for two distinct flow regimes. In stable displacement, solvent and oil become mixed by a dispersion process, and the solvent requirement is small. On the other hand, unstable displacement can degenerate into viscous fingering. The practical result is a considerable increase in the extent of mixing and, thus, in the solvent required. The present paper shows how to use stability theory to optimize solvent recovery of oil. Oil is usually considered to be displaced by a small amount, or a slug, of solvent. Gas in turn follows solvent. Any fingering will permit contact of nearly solvent-free gas and oil, leading to immiscibility and reduced recovery. Thus, our optimum is defined by two restrictions — stable flow and miscibility. Although an immiscible solvent process could prove more profitable than any miscible process, such processes lie outside the selected definition of an optimum. The usefulness of computations based on the present work will depend on the validity of the general theory. Because the important idealizations required tend to minimize the predicted solvent requirement, the results should state correctly the limiting conditions required. Therefore, theoretical calculations should have practical value. This paper first reviews several principles that result from stability theory. The following section describes use of these ideas in relatively simple systems which symmetry makes appear one-dimensional. Of particular importance is the step-by-step design of 3 stable minimum-solvent slug. The use of stability theory in cases of multi-dimensional displacement is discussed and, finally, suggestions are given for simplified practical application of the theoretical results. PRINCIPLES OF STABILITY THEORY The use of perturbation methods to derive stability conditions has been shown by the author.l The discussion is presented in terms of the fractional concentration of solvent in the single hydrocarbon phase. Quite generally, any disturbance can be represented as a Fourier series, of which only the least stable term need be considered. Denoting this term at time t = 0 by cn,

By C. E. Birchenall, C L. McCabe

IN attempting to extend vapor pressure measurements of the type previously reported by Schadel and Birchenall1 for silver and by Schadel, Derge, and Birchenall&apos; for silver-silicon to other systems, it was observed that the materials melted at indicated temperatures 10" to 15" below their accepted melting points. Further investigation revealed that the thermocouple readings were in error due to appreciable conduction losses along the reference thermocouple wires. If the wire diameter of the reference couple inserted into the Knudsen cell was reduced, the correction for the indicating couple changed in a manner tending to explain the melting behavior. When extrapolated to zero wire diameter from measurements with several reference thermocouples of different wire thickness, the melting point of silver then agreed with the indicated temperature at which silver chips were observed to coalesce into a sphere. Approximately the same calibration was given by observing the melting of small wires of silver or gold in the Knudsen cell connected in series with an ammeter, where the leads into the cell were very fine in order to minimize heat conduction. Unfortunately neither of these methods seemed to yield a sufficiently precise temperature calibration to match the apparent precision of the other aspects of the vapor pressure measurement. It was decided. therefore, to redetermine the vapor pressure of silver in another setup under conditions permitting precise temperature measurement. The vapor pressure of pure silver could then be used as an internal calibration of temperature in the older unit in making runs on alloys. This has been done; the present report is a correction to ref. 1. Experimental Procedure The apparatus, shown in Fig. 1, was very similar to that employed by Harteck,3 except that the orifice sizes were smaller and the residual pressure in the vacuum system was probably much lower. A small, sharp-edged hole, nearly circular in shape, was ground into the rounded end of a quartz tube. The orifice area was then measured by tracing the image at known magnification on graph paper and counting the squares enclosed. The silver specimen was sealed into the tube to make a Knudsen cell. A tantalum jacket surrounding the cell served to increase the uniformity of temperature. This assembly was placed in the bottom of a long quartz tube with an inside diameter of about 1 in., which was connected to the vacuum system through a ground joint sealed with picein wax well removed from the furnace. A thermocouple tube inserted through the top of the vacuum line reached into the tantalum jacket so that the thermocouple junction was immediately adjacent to the Knudsen cell except for the protection tube wall. A resistance furnace could be raised to cover the end of the quartz tube containing the cell in such a way that the cell was in the uniform temperature zone 13 in. from the end of the furnace. An ionization gage was included in the vacuum system in the cold lines of wide diameter, immediately beyond the ground joint. The vacuum system consisted of a mercury one-stage diffusion pump, backed by a Welch duo-seal mechanical pump. The pumps were separated from the reactor chamber by a dry ice trap. The ionization gage always read less than 10-5 mm Hg after initial outgassing and before each run was started. Each newly filled Knudsen cell was evacuated at high temperature overnight before the first weighing was made. The cell was returned to the system, heated for a measured time at constant temperature, cooled, and reweighed. The heating and cooling times were quite short since the hot furnace was raised to receive the reactor at the beginning of the run and removed again at the end. The tube heated or cooled quickly. The total mass loss was attributed entirely to effusion of silver vapor from the quartz cell, since empty quartz cells maintained constant mass through similar heating cycles. The vaporized silver condensed on the cold walls of the quartz tube extending above the furnace. Earlier studies in the induction heated unit had shown that the same vapor pressure was found for silver, whether the silver was in contact with the tantalum metal cell or with porcelain or quartz liners. The Pt-Pt-10 pct Rh thermocouple was calibrated against a secondary standard of the same material and found to agree with the published tables. Always operating in air at temperatures below 100O°C,

Jan 1, 1954

At the meeting of the Board of Directors of this Institute on Feb. 16, 1915, the 14 members of the Board present unanimously elected Professor Kemp an Honorary Member. The nomination of Professor Kemp was signed by 21 members of the Institute, none of whom are members of the Board of Directors, and recited his qualifications for Honorary Membership in the following terms: Professor Kemp graduated from Amherst College in the class of 1881, and from the School of Mines, Columbia University, in the class of 1884. After serving as instructor in geology in Cornell University for a few years he was called back to Columbia as adjunct professor in 1891, was made full professor the following year, and has since filled that office with dignity and honor. Among the first to recognize they importance of igneous rocks in the formation of orebodies, his studies have contributed greatly to that increase of knowledge of economic geology in which the Transactions of the Institute has had an influential part, and he is recognized both abroad and in this country as one of the most distinguished scholars in geology which America has produced. This recognition is evident in the honorary degrees of Sc. D. conferred on him by Amherst College in 1906, and LL. D. conferred by McGill University in 1913, as well as by election to membership in the National Academy of Sciences, and a corresponding member of the Academy of Sciences of. Christiania, and the Geological Society of. Stockholm. Professor Kemp was a Manager of the American Institute of Mining Engineers from 1896 to 1898, Vice-President from 1903 to 1904, a Director from 1905 to 1912, President and President of the Board of Directors in 1912, and Past President since that time. During these years he has labored loyally for the upbuilding of the Institute, serving on many committees, as well as in the offices enumerated. He has also served as President of the American Association for the Advancement of Science, the New York Academy of Sciences, and on the governing board of the Geological Society of America and the New York Botanical Gardens. His service is not confined, however, to these labors for the good of the profession and his contributions to exact knowledge of geology. In his almost 25 years as a professor in Columbia University there have come under his influence a great group of young men in whom he has inspired unflagging zeal in the search for truth, and to whom he has set an example of unselfish service. The value of such a service cannot be overestimated and in electing him to Honorary Membership the Institute would officially recognize the measure of appreciation which his professional colleagues have long accorded to him.

Jan 4, 1915

By R. A. Brackett

The most effective means of controlling the dust in the drilling of rock has been found after careful investigation to be collection of this dust at the source. By direct collection, all the dust is collected at the collar of the drill hole and deposited into suitable containers. Equipment for handling this work can be either portable or stationary, depending upon the particular requirements and the application. For most work the portable unit is found most advantageous, and with a capacity capable of handling two drills operating simultaneously. Such a portable unit would consist of a metal cap, or hood, placed against the face of the rock through which the drill steel would be inserted. This hood is connected by a flexible rubber hose to a primary separator, where the bulk of the dust is collected. From here a second length of hose connects to the secondary stage of separation, where the fine particles of dust are collected and which is built in as an integral part of the vacuum producer. Hoods are adapted for vertical, horizontal or stope drilling, and mounted so as to become immediately effective when collaring the hole and remain in place continuously. Such dust collectors can be used with either wet or dry drilling. However, in view of the fact that when drilling dry and using the dust collector, the dust count can be maintained within safe limits, wet drilling becomes unnecessary. Furthermore, it has been found that when using the dust collector not only has the dust hazard been eliminated, but also increased footage can be obtained. Samples taken under a wide variation of conditions indicate that where the dust count required is below five million particles per cubic foot, dust collectors will be required. Opreators, in general, accept the use of this additional equipment favorably, and it is generally felt that such means of collecting the dust will soon be universally adopted. Tests made by the Connecticut Department of Health Bureau of Occupational Diseases show dust counts reduced from 203 million particles to 6.05 million by the use of the dust collector, when drilling dry.

Jan 1, 1934

By E. B. Swanson

Frequent reference has been made to the increased domestic gasoline demand recorded for 1931. This increase was in the neighborhood of 7,000,000 bbl. Although smaller relatively than that to which the oil industry had become accustomed by virtue of the experience of preceding years, the increase was of substantial amount, particularly at a time when any increase at all could be regarded with eminent satisfaction. Less has been said, however, of the 18,000,000 bbl. decline in gasoline shipments to territories and foreign countries. When the loss of business outside the United States is combined with the domestic increase, there results a net loss of some 11,000,000 bbl. in total gasoline demand. The gain of 2 per cent in domestic sales gives way to a loss of 2.5 per cent in total domestic and foreign sales. The United States actually has been losing ground in the international gasoline market since 1924, when shipments from this country equaled 72 per cent of the gasoline shipments from the leading gasoline-producing countries of the world. A loss in relative standing was recorded with each succeeding year. As long, however, as gasoline shipments showed an actual increase, the loss in relative standing was of little concern. Foreign producing centers annually supplied an increasing share of the foreign gasoline markets, but, until the past year, the demand abroad continued to increase at a pace which could accommodate all of the increased output of foreign plants and yet require increasing quantities from the United States. It was not until 1931 that the various factors were combined so as to produce an actual and substantial decrease in the foreign demand for United States gasoline. Consumption in foreign countries generally declined, while the output of foreign refineries and the foreign manufacture of substitute fuels continued to increase. From our own viewpoint, this meant a loss of some 18,000,000 bbl. of gasoline business in foreign countries, one-half of it probably due to the lowering in foreign demand and the other half to the increased output of foreign refineries and the increased utilization of substitute fuels.

Jan 1, 1932

By A. W. Gauger

For perhaps one hundred years scientists have been engaged in attempts at devising a satisfactory method of classification of coal. During this time many charts, tables and graphs have been proposed, some of which have had considerable merit, but no one system has been found to be applicable to all ranks of coal, nor has any one system received general acceptance. In many of the proposals, water eliminated between room temperature and 105" C. has been regarded as extraneous matter and calculations have been made to the air-dry or water-free basis. Such methods of calculation do not lend themselves to satisfactory grouping of the high-moisture coals.1, 2 A consideration not only of the properties of the high-moisture coals and their behavior on drying but of the generally accepted ideas of the coalification process and the role of water in this process indicates that water is an essential constituent of all coals and therefore should not be neglected. For example, in such low-rank coals as the lignites of the Northern Great Plains&apos; deposits the inherent moisture of the lignite as mined plays a very important part in the physical properties thereof. Freshly mined lignite contains upwards of 30 per cent water and is extremely tough and resistant to shock. Upon exposure to the atmosphere, the lump loses part of its moisture and checks and splits, leaving a friable and broken up residue. So far as we have been able to determine, water is the only thing lost in this process and we are forced to the conclusion that moisture plays an extremely important part in the structural properties of the original lignite. With reference to the coalification process, Mack and Hulett3 pointed out in 1917 the important part that water played therein. They observed that water cannot be removed from peat or coal by pressure alone, but only as the result of chemical reaction, and suggested that peat in its early stages may be largely a hydrosol. Slow chemical changes occur over a long period of time until finally the mass becomes more largely a hydrogel. These views are substantiated to some extent by the experi-

Jan 1, 1932

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems. A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. INTRODUCTION The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves are needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemical composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. THE PROBLEM At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1941