Search Documents

By R. P. E. Hermsdorf

THE electrolytic refining of metals for the removal of undesirable impurities has become a recognized necessity in the nonferrous field. Copper, lead, zinc, nickel, silver and gold have been produced in this manner for years. The United States Metals Refining Co., realizing that considerable quantities of lead and tin could be made available to the trade if a satisfactory method of purification of these metals could be established, decided to investigate the possibilities of electrolytic solder. In cooperation with Dr. Edward F. Kern, of the School of Mines at Columbia University, the company developed a process of electrolytic refining of lead-tin alloys using a tin-lead fluosilicate electrolyte. A pilot plant was installed in November, 1927, and the commercial unit was put in October, 1929. Since that time thousands of tons of electrolytic solder have been produced in this plant and consumed by all branches of industry that use solder.

Jan 1, 1936

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.'-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott' first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber's,' but which does not

Jan 1, 1968

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,' a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

PRESIDENT AND DIRECTOR R. C. ALLEN . CLEVELAND, OHIO PAST PRESIDENTS AND DIRECTORS H. A. BUEHLER ROLLA, Mo. JOHN M. LOVEJOY NEW YORK, N. Y. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS HENRY KRUMB NEW YORK, N. Y. PAUL D. MERICA NEW YORK, N. Y. H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. WILFRED SYKES CHICAGO, ILL..

Jan 1, 1937

News has just been received that Flight Commander William T. Hall, a Junior Member of-the Institute, was killed in action on Saturday, May 19, 1917. According to the' Toronto Star, Commander Hall was 24 years of age, a native of Toronto, and a grandson of the late William Kersteman. During the four years of his course in mining at the School of Practical Science, Toronto University, he passed every examination with honors. When war was first declared Commander Hall endeavored to join the artillery as an officer, and for that purpose secured a provisional lieu- tenancy with a Hamilton battery, but he did not receive an overseas appointment, and on being graduated as a mining engineer in 1915, he was offered a position in Chile, which he accepted. He left Toronto on May 27, 1915, and was engaged in Chile as a mining engineer for nearly a year. In the latter part of April, 1916, he decided to offer himself again for service at the front. He crossed the Andes and sailed for Liverpool, where he landed on May 13, 1916. On May 27, 1916, Capt. Hall was given a commission as lieutenant in the Royal Flying Corps. He went to the front on Sept. 1, 1916, and remained there continuously. On April 4, 1917, he was promoted from lieutenant to the rank of flight commander. No details of how Commander Hall came by his death have as yet been received.

Jan 1, 1918

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By D. R. Uhlmann, T. P. Seward, O. Chalmers

A magnetic field has been used to damp out liquid convection during the solidification of castings. Ingots of Al-2 pct Cu were poured from various sperheats (10" to 65°C) into a room-temperature graphite mold located between the poles of an electromagnet. The effect on ingot structure of varying the strength and time of application of the magnetic field was investigated, and the results are interpreted in light 01- current theories of ingot structure. In the solidification of alloy systems, thermal gradients in the melt and differences in density of the constituents are expected to produce convective motion in the liquid. The thermal convection caused by temperature gradients should be present during the freezing of both alloys and pure materials, while the solute convection caused by density differences should be of concern only for alloys. The possible influence of this natural convection on the structure of castings has been discussed by Ruddle,' Chalmers, and Tiller. More recently, an experimental investigation of such effects was carried out by Cole and Bolling. These workers took stationary molds containing lead- and tin-based alloys and. using a brine solution. quenched them from various superheats above their respective liquidus temperatures. When grids were placed across the mold diameter to suppress convection, the grid region was later observed to contain a larger percentage of columnar grains than other parts of the casting or than similar castings poured without the grids present. From thermocouple measurements, they found the temperature in the grid region to be higher than that in the region outside the grids throughout the freezing process, and concluded that convection should be an important mode of heat transfer in normal castings. In addition to such convection arising from thermal gradients or differences in density of the constituents, a further source of convective motion, which we shall call "momentum convection", may be particularly important in small (laboratory-size) castings. By this term we refer to the convective motion produced in the initial pouring process, a motion which is damped out as the linear momentum and angular momentum of the liquid are dissipated. Besides these sources of convection, which are present to some extent in all castings. external influences may also be effective in producing convective motion. Examples of such "forced" convection which have been discussed in the literature include stirring the melt, shaking the mold, rotating the mold, and so forth The purpose of the present study was to examine the effect of convection on the structure of castings poured into a cold mold. In this work, a magnetic field was employed to damp out the convective motions within the liquid, and hence control the extent of con- The effect of a magnetic field on convective currents in a conducting liquid is to induce eddy currents which oppose and damp out the convective motion. vection. The technique of magnetic damping was previously used by Utech and F1emings" in their study of convective effects on impurity banding and other substructure in alloy crystals grown unidirectionally from the melt. In their investigation, fields as small as 200 gauss were found to be effective in damping the convection currents which influence the banding. I) EXPERIMENTAL TECHNIQUE In the present study, alloys of A1-2 wt pct Cu were poured into a room-temperature graphite mold. The mold, in the shape of a circular cylinder, 2 in. ID, 2-3/4 in. OD, 5 in. inside height, and 5-1/2 in. outside

Jan 1, 1967

By R. F. Lee, G. Purcell

Tests carried out in the Department of Mining and Metallurgy at the New Mexico Institute of Mining and Technology indicate that high density rigid foams may, with the addition of suitable fillers, have structural properties comparable with concrete. Since polyurethanes have other useful properties that are unique to the foams, they have great potential value for both mining and civil engineering applications. Polyurethane, a generic term for a wide variety of closely related foam compounds, suggests rather misleadingly that foams are simple polymers of the urethane monomer ethyl carbamate (H,NCOOC,H,) . Polyurethane foams certainly do contain urethane groups, but these need not necessarily preponderate. Other reactive groups may be, and usually are, present so that the final polyurethane product will most likely contain, in addition to urethane groups, aliphatic and aromatic hydrocarbon, ester, ether, amide and urea groups.

Jan 9, 1963

By G. Lavagnino

The old Telegraph mine lies on both sides of Bear gulch, a short branch of Upper Bingham canon, and nearly in the center of the group of mines called the Bingham Mines, about twenty-seven miles southwest of Salt Lake City. It is considered, by local miners as the most important mine of the district. The geological formation consists of Weber quartzites, with subordinate conformable limestones and shales, alternating with porphyritic rocks. These widen towards and connect with the massive backbone of the Oquirrh mountains, while the quartzite develops itself on the slope broken through by Bingham canon. The porphyry not only runs between the strata, but also cuts across them, isolating large portions near the mountain mass, and again on a smaller scale it penetrates some joints in the quartzite. It is a crystalline felspathic rock, containing variable proportions of quartz, mica, hornblende, chlorite, and iron pyrites as accessories. In places, it takes a less distinct or almost uniform fine-grained structure. It has a gray or greenish, and, when much altered, also a reddish or even white color. The quartzite is a fine-grained or almost compact grayish-white or bluish or reddish quartz-rock, containing in places fine scales of mica and grains of iron pyrites as accessories. The raised, folded, or broken masses show well-defined bedding-joints, and their general dip is 35 to 50 degrees towards north or northwest. In the porphyry occur metalliferous veins with a prevailing N.E.S.W. strike. These are in general narrow veins; their principal contents are not dissimilar from those of the other deposits; but there is considerably less oxidation near the surface and the ore is mostly richer in silver and gold. In the quartzite the ore-deposits generally occur on the joints of bedding. The more important deposits occur either in clearlydefined contact-veins or, more often, in somewhat vaguely-defined mineralized zones, that could be called contact-zones. These comprise several masses of more or less altered or decomposed rocks and the newly-distributed products of their mechanical and chemical decomposition, such as breccia and clay in seams or in more irregular bodies..

Jan 1, 1888

By J. I. Budnick, W. B. Ittner III, D. P. Seraphim

A reliable technique has been developed for producing single crystals of tantalum in the form of small diameter wires. By suitably heat treating these and polycrystal samples, first in an oxygen atmosphere and finally in vacuum, it has been found possible to reduce residual resistivities to 10-3 microhm-cm. The purity of these samples is thus comparable to the purities obtained in zone-refined silver, copper, and aluminum. THE growth and purification of pure single crystals of the transition metals is, in general, difficult. The high melting and annealing temperatures of these metals make it necessary to employ rather special techniques in any crystallization process. In addition, the transition metals show a great affinity for and are easily contaminated by nitrogen, oxygen, and carbon. Recently, however. a number of investigators have been successful in growing,

Jan 1, 1961

By D. H. Henley, F. F. Craig, W. W. Owens

The oil recovery performance of systems producing entirely by bottom-water encroachment has been experimentally determined in a series of scaled laboratory-model tests. The effects of well spacing, fluid mobilities, rate of production, capillary and gravity forces, well penetration and well completion techniques on the oil recovery performance have been investigated. The laboratory tests were performed using two uniform, un-consolidated sand-pack models. The models have ratios of the interwell distance to the formation thickness of 12 and 2, respectively. Tests at constant total fluid production rate were performed simulating a range of uniform reservoir characteristics and operating conditions encountered in field operations. The performance was determined by material balance and by observation of the encroachment of dyed fluids into the models. The results of the model tests agreed with those obtained mathematically when the conditions previously considered in theoretical studies were simulated, that is, when the oil and water are of equal density and no capillary forces exist. The model study of bottom-water drive indicated that certain variables can aoect the oil recovery performance to a greater degree than can be predicted by present analytical methods. In one comparison, the oil recovery at a water-oil ratio of 20 (obtained at a wide well spacing) varied as much as threefold, depending upon the system's properties and the production rate. Lesser effect of mobility ratio and no eflect of capillary forces over the range studied were observed. The test 'results also showed that the deeper the well penetration into the oil column, the greater the total water production to a producing WOR of 20. However, the ultimate sweep efficiency, and so the oil recovery to this level of WOR, did not vary significantly with well penetration. Horizontal fractures at the top of the formation did not significantly change the sweep characteristics of the reservoir models when values of radius and fracture capacity encountered in actual reservoirs were used. Impermeable pancakes at the bottom of the well moderately increased the oil recovery efficiency both at water breakthrough and at high water-oil ratios. A method is outlined by which the oil recovery performance of other uniform bottom-water drive systems can be estimated from the information obtained in these model tests. INTRODUCTION When oil is produced from a well which partially penetrates an oil zone completely underlain by water, the water rises directly beneath the well in a symmetrical cone when the system is uniform. Two different flow mechanisms can cause the water cone to form—coning and bottom-water drive. In coning, the aquifer is relatively inactive and the cone is formed beneath the well by the pressure gradients associated with the oil flow to the well. The oil can be produced by a solution-gas drive, an edge-water drive or other driving forces in the interwell area. In a bottom-water drive, the driving force for oil production comes from an upward encroachment of the underlying active aquifer. Two papers have analyzed the theoretical performance characteristics of bottom-water drive reservoirs. In the initial mathematical investigation, Muskat' established the equations which determine the pressure distribution in this type of reservoir and solved these equations for certain conditions. Specifically, it was assumed that the water and oil had equal mobilities and equal densities, there were no capillary forces, the pressure throughout the oil zone remained above the bubble-point pressure, a constant pressure existed at the initial water-oil contact and the oil was completely displaced by the encroaching water. These assumptions were used in obtaining analytical solutions. In general, Muskat found that the sweep efficiency to initial water breakthrough to the well was larger for the thicker oil zones, the closer well spacings, the lower ratios of vertical to horizontal permeabilities, the smaller the penetration of the well into the oil zone and the smaller the bore size of the well. The production history after water breakthrough was expressed as a volumetric sweep efficiency at a given producing water-oil ratio. The results indicated that cumulative oil production at producing water-oil ratios of 10 is less affected by the well spacing than is the water-free production history. Muskat studied well spacing which today would be regarded as close. The maximum value of his dimensionless well spacing (ratio of interwell distance to formation thickness) was 4.3. This would require the development of a 50-ft-thick oil sand on less than 10-acre spacing if the vertical and horizontal permeabilities were equal, with

By Elmer W. Pehrson

The term "survival" in the title means the preservation of a society in which men are free from the political and economic restraints that characterize totalitarian systems, be they communist, socialist or facist. It means the ability to withstand the enemy's offensives in the fields of propaganda, commercial competition and, if necessary, war. The temptation to substitute "victory" for "survival" is great but a realistic appraisal of the creeping socialism and demagoguery that pervade our time indicates that we may have to be content with survival in status quo. "Mineral strength" means assurance that adequate supplies will be available to meet all the contingencies of cold and hot wars. The overall mineral position of the U. S. viewed in the light of these premises is far from secure. It is true that we are the leading producing and consuming nation of the world, but the Soviet Union is gaining and the Sino-Soviet Bloc confronts us with a sobering potential. The emergence of the Common Market in Europe as an economic and political unit places a third independent entity into the competition. Our total mineral output continues on an up- ward trend but the reverse is true in certain strategic commodities. Moreover, consumption is moving ahead faster than production so that there is increasing dependence on imports which has significant adverse geopolitical connotations. There is widespread belief that our resources can at least maintain present levels of self-sufficiency during this critical period in world history, but social dreamers, the labor monopoly, and trade and taxation policies have discouraged aggressive activity in exploration and development, and access to essential foreign sources is threatened by a variety of circumstances. Our stockpiles, belatedly built up to achieve minimum protection against shortages in time of war, are under. political attack and threatened with partial destruction on the basis of what are at best uncertain assumptions regarding the new: look of global warfare.

Jan 11, 1962

By Riki Kobayashi, D. L. Katz

The conditions at which methane and water form solid hydrates have been extended from 4,000 to 11,200 pounds per sq. in. The curve at high pressure had been in doubt because of Villard's report of a critical decomposition temperature. The paper explains the nature of the hydrate curve at high pressure and its dependence on fluid phase behavior. Extropolation of the methane hydrate curve indicates a pressure of 40,000 pounds per sq. in. will cause hydrates to form at a temperature of 100" F. INTRODUCTION The conditions under which natural gases form hydrates when liquid water is present have been studied by several investigators up to pressures of about 4,000 pounds per sq. in. The early work by Villard on hydrates of methane and ethylene13, ethane'', and propane14 included references to critical decomposition temperatures of the hydrates. Villard's work raised the question as to whether the pressure-temperature curve for methane-water hydrate continued above a temperature of 70.7°F. or whether this was the maximum temperature at which hydrates would form. This paper extends the experimental data on methane hydrate to 11,200 pounds per sq. in. A discussion of phase relations in the hydrate region for the hydrocarbons and of the methane-water system at high pressures is included. PREVIOUS WORK Villard suspected that methane hydrates could not be formed at temperatures above 21.5°C. (70.7°F.)la irrespective of the pressure of the liquid-vapor system. However, he was limited in his studies by his apparatus in 1888 to pressures not greater than 300 atmospheres (4,410 pounds per sq. in.) so that there has remained some doubt as to the existence of such a maximum temperature in this region. For the case of ethylene hydrates, however, Villard does specifically state the occurrence of what he terms a "critical temperature for the decomposition of the hydrates"13. Fig. lB shows a pressure-temperature projection of the three-phase locus, hydrate-ethylene rich liquid-vapor (H-L2-V) terminating at the critical locus in which L² and V assume similar properties. Throughout this paper the following phase designations will be used: H for hydrate, Ll for the water rich liquid. L2 for the

Jan 1, 1949

BARBOUR, PERCY E., Deputy Supt., (Captain), New York State Troopers; Captain, 22nd Regiment, N. Y. N. G. BARLING, 1i. B., 1st Lieutenant, Engineer Officers' Reserve Corps. CHAPMAN, R. H., Major, Engineer Officers' Reserve Corps. DUNN, THEODORE S., 1st Lieutenant, Engineer Officers' Reserve Corps. DWIGHT; ARTHUR S., Major, Engineer Officers' Reserve Corps. FORBES, CARROLL R., Captain, Engineer Officers' Reserve Corps. GOODSPEED,. G. E., JR., 1st Lieutenant, Engineer Officers' Reserve Corps.

Jan 7, 1917

By B. J. Kochanowsky

TO improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi; Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,2 editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature." Present blasting theory is based upon two assumptions. 1) The blasting force of explosive acts in concentrical and spherical form. 2) Rock resistance against the explosive force is directly proportional to the strength characteristics of the rock. The first classical formula based on theoretical fundamental in blasting theory for explosive charge calculation was introduced by Vauban, a military engineer who lived 300 years ago. It was Vauban who proposed the famous formula L = w3 q, where L is the explosive charge, w = line of least resistance, and q = specific explosive consumption proportional to the weight of rock. Later engineers used q as proportional to the strength of the rock. Since Vauban's time different suggestions concerning blasting theory have been proposed. However, the principles stated at that time so affected the thinking of later generations that his formula is still in use and practically unchanged. The first controversy concerned the form of crater. It was found that geological features of rock affected its form. The factor q was analyzed thoroughly by Lares3 and later by Ohnesorge," Weichelt,5 Bendel,6 and others, but the assumption remained that resistance against explosive force is directly proportional to the strength of the rock blasted. The greatest controversy, which has not yet been settled, concerned w. It was noted that w3 is more appropriate for long lines of resistance and w2 for lines of resistance less than 15 ft. Based on the assumption that the explosive force acts concentrically and spherically, spacings between charges were limited to distances not greater than the length of line of least resistance. Sometimes larger spacing is recommended, but this is due to the advantageous geological and physical properties of rock and not to the action of an explosive force as such. In addition to the classical formula, empirical formulas are used widely. These state that the explosive charge is directly proportional to the volume of blasted rock in cubic yards, and the amounts of explosive required are usually expressed in pounds of explosive per cubic yard of rock. Empirical and classical formulas are contradictory. In the empirical formula, but not in the classical formula, explosive charge is taken proportional to all three space axes: line of least resistance, spacing, and bench height. In spite of this contradiction, both formulas give good results. This is possible because as now practiced the explosive charge calculation for heavy burdens need not be highly accurate. Each, open pit or quarry, usually works with a certain relation between bench height and line of least resistance and between charge spacing and line of least resistance. When these relations are changed, however, the specific explosive consumption q changes greatly. This is one of the reasons why the principles on which the formulas are based appear to be incorrect. In addition to the formulas discussed, others exist and are based more or less on the same theoretical

Jan 1, 1956

HAVING demonstrated to you above the practice of bringing silver to its ultimate fineness and perfection, it now remains for me to describe how the two kinds of metals that are found in the smelting product that you made from the ores are to be brought to their end: One is copper and the other lead, and perhaps a third is gold, if per-chance the silver that you refined in the cupeling hearth contained any. It would be almost impossible that it should not contain any, because either a little or a lot is almost always found as an admixed substance not only in silver but in. every one of the other metals as well. But in order to continue in sequence, you must suppose that there is some gold and that, of the two materials you have that I mentioned above and told you to save, one is the matte (calling it according to the usage of Germany, * since I do not know a more exact or better word for describing it to you) and the .other is the litharge that you took from the cupeling hearth. In addition, the hearths themselves are saturated and full of lead. If these things should remain in their present condition they would be useless bodies without any perfection. First, taking one of the three said parts, as a material of greater quantity and also as a thing that needs greater labor, and because, being reduced to the point I have told you with smelting and evaporation, it is nearer to its end, I shall tell you what must be done in order to bring it to pure copper. As I have told you, there are two materials on hand, one of which is the matte and the other the litharge. Each at first sight seems a half-burned thing; one has already been finished metal and the other is to be, but in my opinion the matte is nearer to its end than is the litharge because the latter has been dried by the power of the fire and re-formed from another body. Now leaving aside the discussion of this thing, after the matte has been well evaporated and reduced, it is taken and put on a forge. In front of the tuyère a receptacle is made of stones that neither calcine nor melt, or of coals and powdered clay, in the form of a little cradle that is longer than it is wide and not very deep. Its length should be about one and a half

Jan 1, 1942

Jan 1, 1889

By Winthrop P. Haynes

The symposium on production for the year 1944 includes more foreign papers than any one of the past three years, because of a partial relaxation of the censorship in many Western Hemisphere countries. The committee was not successful, however, in securing papers from Europe and the Near and Far East at this time, with the exception of Saudi Arabia and Bahrein. Where possible, these papers include summaries upon production for the missing war years, so that we shall have no permanent gap in the records. At the close of the war, we hope again to publish the usual more complete form of report for all important oil-producing countries. EXCERPTS FROM CIRCULAR TO AUTHORS In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each place in the table may represent one of three possibilities; either the proper entry is determinable and can be supplied by the author, or an approximate figure can be supplied which is the author's best guess and should be entered followed by an x, or it does not apply to the particular field and the space is left blank. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. . Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone. The net thickness of the producing formation should be the thickness of the producing zone, less the estimated amount to cover the portions of the zone that do not yield oil, such as dense shales, etc. It is recognized that for some fields the authors can only make rough guesses; in such cases, they should enter their best estimate followed by an x. Average production per acre-foot need not be reported as it can

Jan 1, 1945

By Walter L. Crow

MUCH has been published on highly technical phases of grinding. Very little has been written on how a mill man can improve his operations by determining the optimum size assortment of grinding balls that should be added as a makeup charge. This ball rationing is not to be confused with the ball ration used as an initial charge when the mill is started up. Ball rationing is considered for one or more of the following purposes: 1) to increase throughput of the mill, 2) to reduce the power required per ton of ore ground to the desired size, 3) to reduce steel consumption per ton of ore ground, 4) to improve product size, and 5) to lower retention time of ore in the mill.

Jan 7, 1957

By T. B. Counselman

The importance of concentration of iron ores too low in grade to be smelted direct is shown by Table I, showing 1940 ship- ments from the Lake Superior district. Canadian ores are omitted. Only in Minnesota is concentrating, other than crushing and screening, prac- ticed at present. Tonnage produced by various methods of concentration is shown in Table 2. The curves in Fig.. I show the gradual increase in tonnage of concentrated ores shipped, compared with total shipments from Minnesota. Most of the concentration work is performed on the Mesabi Range. This range is about 100 miles long, and not over 3 miles wide from the line at which the formation tapers out to a feather edge on the north to the place on the south at which, some 600 ft. thick, it is overlain with slates. Classes OF Ore The Mesabi Range contains three classes of iron ore. First is the unaltered taconite, or banded iron-bearing chert. It is estimated that there are some 60 billion tons of this material, which contains, roughly, 25 to 30 per cent iron. This material is virtually untouched, since no commercially successful method has yet been found for concentrating it to a grade suitable for the blast furnace. Intensive exgerimental work is in progress, and the problem is gradually being solved. In 1922 the Mesabi Iron Co. spent several million dollars erecting a large-scale pilot plant for concentrating and sintering the magnetic taconites on the east end of the range. An important tonnage of high-gade sinter was shipped to lower lake furnaces, proving that the taconite can be concentrated to a satisfactory grade. The costs, with equipment and methods then in use, were too high for

Jan 1, 1943