Search Documents

By D. E. Munson, H. J. Sutherland

Surface subsidence caused by underground mining is described through complementary influence functions. The complementary functions developed here differ from the simple functions previously used in that the surface displacement is the result of the combined contributions of the mined and unmined zones. This eliminates computational difficulties experienced with the simple functions in determining the deflections above the rib side and in the eventual application of influence functions to complex room-and-pillar configurations. Although the analysis framework presented is intended for predicting subsidence over complex mine configurations, use of the complementary functions is illustrated adequately by application to a longwall panel of the Old Ben No. 24 coal mine.

Jan 1, 1982

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory state of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which are useful for predicting machine performance and give, acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary in commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed' in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted. In its first form, as stated by P. R. Rittinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include .the concept of surface energy; in this form it was precisely stated by A. M. Gaudin2 as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended. According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps, 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported' that support the theory in its first form by indicating that the new surface produced in. different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work" done on. the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading since it does not follow the regular breakage pattern of most materials but is relatively harder to grind at the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory' is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr/log 2.5 The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in. reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-1.5 If a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The'evaluation in terms of kw-hr per net ton of 200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of -200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned, with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1952

By S. R. Krogh, T. O. Olsen

Analytical expressions for the breakage rate as functions of mill charge, mill speed, particle size, ball diameter, and ball load are derived, using idealized models for probability of breakage (Gaudin and Meloy), energy distribution (Mempel), and arithmetic mean of effective ball energy (Langemanns). Computational results using the theoretical equations are compared to experiments. The equations enable simulation of ball mill grinding at different grinding conditions.

Jan 1, 1973

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-As the die-casting process is so very different in character from the process of making sand molds, it is often considered that entirely different methods of pouring, gating, venting, etc. should be used. There is really, however, no essential difference in the making of (lie castings and sand castings, and similar methods should be used in each process. In the matter of gating, the metal should be introduced at a central point, as nearly as possible, so that it will have an equal distance to flow from the point of entrance to the most distant points of the mold. This will cause a uniform rate of congealing of the casting and prevent streaks and cold shuts. The venting should be done in such a way that a free exit of the air in the molds can occur. It should be less difficult to take care of the venting of a die-casting mold than to vent an ordinary sand mold. In the case of a sand mold, the venting is left, to a considerable extent, to the judgment of the molder, and it is possible that no two molds will be vented in a similar manner. Further than this, after a vent has been made in a sand mold, it may become clogged by the sand and for this reason be inefficient. There is also quite a variation in the pressure of the metal entering a sand mold, due to varying heights of the pouring gate. In a die-casting mold these factors can be controlled more closely. The vents should be so disposed that the air in the mold compressed by the entrance of the metal may be able to leave the mold at a uniform rate and by exits located symmetrically. These exits are made quite small on molds at first, as they can he easily enlarged if necessary, and they are tapered so that a free flow is guaranteed without danger of the metal spurting out from the die. Uniformity of pressure of the metal as it enters the mold is very important and, as the pressure is mechanically applied, its control is not difficult. It is true that a sand mold has much less of a chilling effect on the metal poured into it than has the die-casting mold, but, outside of this point, there is a great similarity between the die-casting process and the process of making castings in sand folds. It is suggested that much would be gained by regarding these two processes as not essentially different.

Jan 4, 1919

By Claude H. P. Lupis, John F. Elliott

IN the recent past, extensive use has been made of the interaction coefficient in treating the thermody-namic behavior of components in solutions at dilute concentrations. The development of this concept by wagner1 and chipman2,3 is sufficiently well-known so that its elucidation here is not necessary. The present discussion is focused on the relationship between E and e. The usual forms of the coefficients are:

Jan 1, 1965

Jan 1, 1906

By Arthur Taggart

THIS paper describes the result of a series of experiments run in the laboratory of the School of Mines, Columbia University, during the winter of 1927-28. It shows that the several operating adjustments of a pneumatic table produce effects in the action of a, given coal that may be grouped into two classes, viz.: stroke length, speed and rocker-arm angle, which affect longitudinal travel; air supply and table slope (transverse and longitudinal), which determine transverse travel. The magnitude of the effect of the different adjustments varies. Some of the adjustments affect stratification of the bed, both as respects size and specific gravity of the bed components, as well as direction of travel. Operation of a pneumatic table is fundamentally different from that of a wet table in that the former exerts, through the air supplied, a force on the particles upward away from the deck which is lacking on the wet table while, on the other hand, it lacks the positive control over cross travel that is supplied by the wash and feed water.

Jan 1, 1929

By D. L. King, B. A. Schepman

A number of unique thickener mechanism designs with the operating results achieved in various installations are discussed. These unusual designs include new types of raking arms, lifting devices, and feed-wells employed to obtain higher underflow densities and minimum operator control or improved overflow clarity. Several installations of large thickeners in which the underflow lines pass upward through the center to eliminate tunnels are reviewed. The location of the lines and pumps with the maintenance and operating records are included. Several types of automatic lifting device controls are used to provide storage in the thickener. Some of the installations employing underflow density controls are achieving excellent operating results. Thickeners or sedimentation basins are used in minerals beneficiation plants for three basic purposes. These are 1) Concentration, or to raise the density of a liquid-solids slurry. 2) Clarification, or removal of finely divided solids from a slurry. 3) Hydroseparation, or removal of a specific fraction of solids from a slurry. The concepts that control the size and configuration of basins used for these purposes are different. Likewise, different equipment is properly employed to accomplish these various objectives. The pattern of liquid and solids flow in the clarification zone of a sedimentation basin used for thickening or raising the density of a pulp normally is not critical. That is, the solids normally will drop or plunge to the bottom quite readily, and the liquid separates itself from these solids so as to overflow the basin in a relatively clear condition. When clarification or removal of finely divided particles is to be accomplished, the flow patterns in the basin are extremely important. The velocity of the incoming stream must be dissipated and the liquid flow distributed ]In the tank so that the feed is not divided into streams that flow directly to the overflow carrying the fine:ly divided solids that are to be removed. Similarly, the configuration of the arms that provide the raking and thickening of the pulp is not as important in basins primarily devoted to clarification. In thickening, the design of the arms and the manner in which the pulp is moved or worked, can contribute appreciably to the thickening process and achievement of a higher density underflow. THICKENING As the grade oi ore bodies throughout the world generally decreases, and chemical processes, hydro-metallurgy, and other more refined methods of minerals beneficiation are required, problems in thickening become more acute. Difficult operating conditions, previously encountered only occasionally in thickening metallurgical slurries, or clarifying process streams in the mill, are now the rule rather than the exception. Fig. 1 illustrates some of the different types of raking arms that are successfully achieving the desired goals in pulp thickening. The conventional raking arms consist of a relatively simple truss with the blades attached to the bottom chords. This design provides proper Concentration of many 'normal' slurries. A modificaiion of this design as shown in the center is being used with excellent results on large thickener basins where it is desirable to have a

Jan 1, 1962

By Everett D. Jackson

The largest deposits of chromite in the United States occur in tabular layers in the lower part of the Stillwater Complex, Montana. Nearly 900,000 long tons of chromite concentrates have been produced from mines and mills in this area, and reserves equivalent to more than 2,500,000 long tons of Cr2O3 remain in the ground. Layered concentrations of chromite (known as chromitite zones) occur only within olivine-rich layers of the Peridotite member of the Ultramafic zone of the Stillwater. As many as thirteen chromitite zones, lying conformably one above another, have been found, but only five of them are thick enough to be of any conceivable economic interest, and only two of them have been mined to date. Individual chromitite zones can be recognized by their distinctive internal character and by their stratigraphic position in the Peridotite member. The chemical composition of chromite varies consistently between and within the different chromitite zones. The zones range in thickness from about an inch to more than 12 feet, and the Cr2O3, content of their chromite ranges from 36.6 to 49.2 weight per cent. In any given area, the G chromitite zone is the thickest, but the chromite of the H chromitite zone has the highest grade. Laterally, the thickness of the chromitite zones is related to the thickness of the Peridotite member; in general all are thicker in the eastern part of the Stillwater than in the western part.

Jan 1, 1968

By E. S. Shaw

Utah continues as a very unimportant factor in oil and gas production. During the year 1933 there were no developments of noteworthy significance. There were no completions of either producers or dry holes during the year. The only commercial production in Utah has been from the five fields listed in Table 1 and mentioned briefly in the following paragraphs. Virgin Field.—Oil was first discovered in 1907 in a well drilled in sec. 13, T.41S., R.12W. Of the first 15 wells drilled, all but three were failures. In 1920 production from four wells from 550 to 600 ft. deep was about 20 bbl. per day. San Juan Field.—The majority of drilling in this area was done during the years 1908 to 1911. Probably the first commercial well in the field was that drilled in NW.$i sec. 6, T.42S1 R.l9E., in 1909. Farnham Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1923. A number of years later a second well was drilled by The Carbon Dioxice a mica1 Co., the present operator, which markets the gas in the manufacture of "dry ice" and allied products. The eslimated production, as indicated in Table 1, includes 500 million cubic feet estimated to have been lost while drilling the discovery well. Cisco Dome.—The discovery well was drilled by The Utah Oil Refining Co. in November, 1924. The Crystal Carbon Co. markets the gas in the manufacture of carbon black. Ashley Valley Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1925. The Uintah Gas Co. markets the gas in Vernal, Utah, for fuel. Woodside Structure.—In February, 1924, gas was discovered in a well drilled by Utah Oil Refining Co. in sec. 12, T.l9S., R.l3N., on the Woodside structure. This gas is reported to contain an appreciable amount of helium. It is being held as a helium reserve by the United States Government. Salt Valley Structure.—The test of the Utah Southern Oil Co. in sec. 31, T.23S., R.21E., on the Salt Valley structure has been shut down for some time at 6120 ft. This test has passed through more than 5000 ft.

Jan 1, 1934

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Smallwood mine is part of the Iron Ore Company of Canada's Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year, 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million of crude and 7 ¼ million tons of concentrate and pellets, which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. Since both rotary and jet piercing drills are used, it is often desirable in planning to know in which regions of the orebody, or new orebodies, a particular drill will be most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock property. For the rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes, and the mine distribution curve for grinding factor index.

Jan 9, 1965

ANNUAL MEETING OF THE NEW YORK SECTION - The annual meeting of the New York Section was held at the Machinery Club, May 7. While the dinner, at which fifty attended, was in progress, the names of the nominees for next year's officers were posted. The result of the election was as follows: Chairman, E. P. Mathewson; vice-chairmen, William Y. Westervelt, R. M. Atwater, Jr.; treasurer, Wilber Judson; executive committeemen, Lucius W. Mayer, Edwin S. Berry. The subject for the evening was "Organization and Campaign in France of the 27th Engineers." Colonel O. B. Perry described the many difficulties surmounted, for it was necessary to work with untrained men ALLEN H. ROGERS WALTER S. DICKSON CHAIRMAN OF NEW YORK SECTION SECRETARY OF NEW YORK SECTION and shortage in supplies. He described the unusually fine character and physique of his officers, which made it possible to make the untrained men most efficient. He described in some detail the work of building bridges over the Meuse River and the bringing up of supplies to the first army base, in particular at the Argonne-Meuse sector; General Pershing gave a personal commendation of the work undertaken by this regiment. The Colonel described the methods of operating the transportation of ammunition and supplies to the "army dumps," by which at the time of signing the armistice there had been brought up 600,000 tons of equipment for use in the projected campaigns. An interesting item was that 3,600,000 sand bags had been provided, in case the Germans should be able to turn the line of the American troops. Captain Edwin S. Berry described the methods of sending materials to the front lines and gave figures to indicate the huge quantities required, adding that the order of preference was troops, ammunition, food, and engineers' supplies. The speakers then answered several questions given by the members present. WALTER S. DICKSON, Secretary.

Jan 6, 1919

By Paul A. Bailly

“For innovative leadership in bringing about a quantitative rationality to mineral exploration; for the impact his efforts and wide respect have made on national mineral policy issues; for his effective managerial role in major mineral discoveries; and for his lecture, ‘Managing for Ore Discoveries.’”

Jan 1, 1980

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

By H. C. Doepken

Wrought Hadfield steel was tested in axial tension at from 100° to —196°C, to determine flow and fracture stresses as well as conventional properties. Ductility and related properties, such as fracture stress, decreased continuously with temperature. Peculiarities during straining indicated possible martensite formation or mechanical twinning. THE mechanical properties of austenitic manganese steel have been summarized by Avery and Day,' including the low temperature tensile properties reported by Hadfield and coworkers2,3 " These data show the material to be brittle at both liquid oxygen and liquid 'hydrogen temperatures. Avery and Day report considerable ductility measured by Charpy V-notch tests at —100°F (-73°C). Since the review of low temperature properties by Seigle and Brick' show face-centered cubic structures, other than Hadfield steel, to be ductile at low temperatures, it was felt that a study of tensile properties, between the reported intervals, should show whether the decrease in ductility was a gradual decline or an abrupt drop beginning at some intermediate point. X-ray examinations were made in an attempt to shed further light on the mechanism of work hardening of austenitic manganese steel. The presence of a magnetic constituent has been found by Hall" and by Avery, Homerberg, and Cook." Krivobok7 demonstrated the growth of magnetic constituents on reheating cold-worked specimens. Hadfield2,3 ' and Goss found no a iron. The steel from which the specimens were taken was commercial hot rolled % in. diam rod of electric furnace steel. The ladle analysis was as follows: C, 1.40 pct: Mn, 12.11; P, 0.060; S, 0.012; Si, 0.120; Ni, 0.080; and Cr, 0.090. Fifteen specimens, 6 in. long, were cut from a

Jan 1, 1953

By C. O. Dale, W. J. Rundle

THE upper Mississippi Valley zinc-lead area was the first major lead producing section in the United States. The lead ore, found near the surface in crevices, was relatively pure galena that could be smelted directly into lead, at first in log hearth furnaces and later in more efficient blast type furnaces. French Canadian fur traders encouraged the Indians to mine the lead ore and showed them how to smelt it into lead that had a high value for bullets.1 Nicholas Perrot found lead ore on the Mississippi River bluffs near the junction of Wisconsin and Illinois and in 1690 established a trading post on the Wisconsin side of the river opposite the present site of Dubuque, Iowa.2 Shortly after 1720 discovery of Mine La Mott in Missouri diverted considerable attention from the Upper Mississippi area. Mining continued on a desultory basis with operations concentrated in the Galena, Illinois-Dubuque, area. In 1740 at least 20 miners were at work in the Fever River area around Galena and are reported to have shipped 2500 70-lb pigs of lead to Kaskaskia in 1741.3 Julien Dubuque established a mining and smelting operation in 1790 near the city that bears his name 'and was granted sole right to exploit the mining operations on the lands of the Sauk and the Fox Indians. He is reported to have produced 30,000 70-lb pigs of lead in 1805. Following the death of Dubuque in 1810 the Indians refused to let the white miners enter their lands, and little was done on the Iowa side of the river until the Indians were removed by treaty with the United States government in 1832.4 Early mining was entirely for lead but as the crevices were followed down, increasing percentages of zinc sulphide and zinc carbonate were encountered and at first discarded. Later a market became available for the zinc ores, and hand jigging devices were made to separate the lead," the zinc, and the rock or waste materials. The first record of zinc production from -the area is for 1860. Production of zinc passed that of lead before 1900, reached a peak of 64,000 short tons' in 1917, fell off rapidly and continually to about 2000 short tons in 1938, and since 1940 has ranged from 11,000 to 19,000 short tons. Lead has been of considerably less importance since 1900, and at present only about 10 pct as much lead as zinc is produced. Practically all of the zinc ore has come from orebodies that are rather flat and wide with, considerable length as compared to width. Most of the early lead came from the crevice type deposit, but present production is from the predominately flat zinc orebodies. The Graham-Snyder orebody, scene of Eagle Picher operations, is practically all zinc with little or no lead being recovered. Marcasite, present in varying amounts, makes production of finished concentrates by gravity separation impractical. Satisfactory lead and zinc concentrates have been produced since flotation was introduced in the area in 1927. An acid recovery plant was operated for about 20 years after World War I, but it has been dismantled, and no recovery of the iron sulphides in the ores of the district is being made at the present time. In June 1950 there were three companies operating mines and mills, Tri-State Zinc Co., Calumet & Hecla Consolidated Copper Co., and Eagle Picher Mining and Smelting Co. The Vinegar Hill Zinc Co. had completed a shaft at a new orebody and had started to develop the mine which will supply the Cuba City mill. The Cuba Mining Co. was holding the Andrews Mine inactive. The Dodgeville Mining Co. was not operating but was exploring for additional reserves. Several small mines were selling ore to the Eagle Picher mill. A general area map is given in Fig. 1. The Eagle Picher Mining and Smelting Co. entered the area in 1946 with an active exploration campaign. Leases on a block basis were secured for the area south from the Wisconsin-Illinois line near

Jan 1, 1952

By M. Albertson

AT Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin' Was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 in.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 in.), the width at the lower lobe was about. 1000 ft., and the, width at the narrows probably. 400 to 500 ft. The original depth of water varied from 20, to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft.. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the. lake. About

Jan 2, 1921

By Hans Allenius, R. T. Hukki

This paper describes in quantitative terms the effect of sharpness of classification on the performance of the closed grinding circuit. The analysis is based on a large number of laboratory experiments designed to simulate the two most common industrial closed grinding systems. The experimental results show quantitatively the degree of improvement achievable by more efficient classification. In an earlier paper1 the senior author has presented a trend showing qualitative analysis of mill and classifier performance in tile closed grinding circuit. According to this analysis, the master key to a major improvement appeared to be effective removal of finished fine material from the classifier sands, or in other words, improved sharpness of classification, leading simultaneously to a substantial reduction of the circulating load. One purpose of this paper is to present the results of a quantitative investigation of the closed grinding circuit. Another is to set forth the essential pertinent variables revealed by the quantitative experiments carried out by the junior author. In the two most common systems of closed-circuit grinding, (1) feed to the circuit is introduced into the grinding unit, normally the ball mill, operating in closed circuit with the classifier; or (2) feed to the grinding circuit is introduced into the primary grinding unit, normally the rod mill, discharging into the classifier in closed circuit with the secondary grinding unit, normally the ball mill. In the following discussion, these two systems are analyzed separately in the indicated order. BALL MILL - CLASSIFIER CIRCUIT The Test Apparatus and Procedure: The test appara- tus included: (1) a F 195 mm x 220 mm laboratory ball mill rotated at a speed 77% of the theoretical critical speed, and a 7-kg batch of F 20 mm-F 50 mm steel balls; (2) a conventional 65-mesh test sieve and a Ro-Tap sieve shaker serving as a classifier; and (3) a Permaran instrument manufactured by Outo-kumpu Co. for surface area determinations by the permeability method. As no continuous closed-circuit experiments could be brought about on a laboratory scale, the process was broken down into alternating grinding and sizing steps in such a way that the new feed plus the returning sands always formed a batch of 1000 gm. For each selected grinding period and for each selected sharpness of classification the basic steps were repeated six times. Steady-state conditions were then reached. Crystalline vein quartz was used as a test material. Feed to the process consisted of -10-mesh fraction of this quartz crushed in rolls. This fraction included 15% of-65-mesh material. Experimental Results: The general flowsheet is shown in Fig. 1. Table I gives the essential data obtained representing steady-state conditions under the indicated set of variables. The table is based on 110 grinding experiments, 440 screen analyses and an equal number of specific surface area determinations. Fig. 2 shows the relationship between the cumulative net energy consumption and the cumulative number of mill rotations as evaluated by separate experiments. Note that this relationship is not linear but is instead represented by a slight curve. The data given in Table I are presented in graphical form as follows: Fig. 3 shows the produced -65-mesh material in grams per minute vs. time of grinding in minutes; the sharpnesses of classification at 65 mesh were 100%, 75% and 50%. It is clearly indicated that the highest-capacity figures call for relatively short grinding times and for the sharpest possible classification. Fig. 4 presents the specific surface area on the final -65-mesh product in square centimeters per gm vs. time of grinding in minutes. In conventional mineral dressing processes, a final product characterized

Jan 1, 1969

By Kenzo Ikeda

The Kosaka smelter is situated in the extreme northern end of Hondo (the main island of Japan) 15 mi. east of Odate, on the government railroad, to which it is connected by a private railway. It contains ten blast furnaces having a maximum daily capacity of 1600 short tons of ore, conducting a slow pyritic smelting entirely without coke or limestone, and with a charge carrying over 50 per cent. of briquetted and agglomerated fines. The matte (35 per cent. Cu) is blown in two basic-lined barrel converters, the blister copper (98.8 per cent. Cu) being cast at once into anodes. The adjoining refinery contains 600 tanks with a maximum capacity of 1300 tons of cathodes per month, the byproducts being gold, silver, and bismuth. At present, working at about half capacity, the whole plant consumes 2000 kw. of hydro-electric power, and employs 850 men and women. The ores are derived from two principal sources: The relatively new Hanaoka mine, 20 mi. from the smelter, yielding copper pyrites by underground mining, and the old Kosaka open-cut mine, 1 1/2 mi. from the smelter, yielding three different ores: (a) kuromono, a compact finegrained mixture of barite (32 per cent.), zinc blende, galena, and pyrite, the whole carrying about 2.5 per cent. Cu; (6) cupriferous pyrites with 2.4 per cent. Cu; (c) siliceous ore with 2 per cent. Cu. The Hanaoka ore now constitutes approximately one-half of the charge, almost replacing the Kosaka kuromono which was the ore chiefly smelted until 1913.'

Jan 1, 1923

By Ernest M. Spokes, Martin A. Thieme

A simulation model developed to analyze scraper-pusher utilization in open pit mining systems is described. The mining simulator discussed was developed as a tool to aid management in evaluating alternative open pit haulage schemes and to reduce the risk involved in the selection of equipment.

Jan 1, 1973