Search Documents

By Richard Moldenke

The paper describes the making of pig iron from the Mayari iron ores of Cuba. The outstanding feature f this pig iron is a considerable content f nickel and chromium. As a marked improvement in the quality of castings has been noted when this iron is used in the foundry mixtures, a series f melting tests f mixtures of great variety of composition was conducted with the idea f getting comparative strengths from which the effect of nickel¬chromium could be seen. These tests, on account of their number, and degree of accuracy desired, were made by the crucible melting method. The paper gives the tables of results, a series f curves showing the inter-relation of the elements involved, and a summary of the conclusions derived. THE presence of nickel-chromium in pig iron made from Cuban ores is so well known that the word "Mayan" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there has been increasing interest in these ores. The TRANSACTIONS contain numerous references to them. This iron ore, which is shipped to the. United States in the nodulized state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of Mayari ore for pig iron for the better grades of finished iron products. The present point of consumption of Mayari ore is at Sparrow's Point, where Mayari pig iron of any desired composition is made. The com-

Jan 9, 1922

By Newell Alford

FORECASTS of future timber consumption in soft-coal mining are handicapped by; the lack of adequate experience records for estimating properly the timber requirements of the industry. Data were obtained from plants where records are kept or from operators who collected the information and to these were added FIG. 1.-GROWTH OF POPULATION IN UNITED STATES, FROM PEARL'S ?BIOLOGY OF DEATH." composite figures for the continental United States in 1905 and 1919 1 and for central and. Western Pennsylvania and for Illinois in 1922.2 The result, representing slightly over 928;000,000 net tons, is shown in Table 1. Some of the companies furnishing data were unable to segregate the timber into classes of use but for those who did, Table 2 shows the board feet of posts and cross bars used per ton of coal mined and the, percentage of the total timber consumed that was used in roof support. The wide variation in amounts of timber per ton of coal mined is the result of

Jan 5, 1924

By A. D. S. Gillies

The effectiveness of coal mine face ventilation and the ability of airflow to maintain satisfactory methane and respirable dust levels in the working face area has been studied through the use of scale modeling techniques and underground testing procedures. In particular, consideration has been given to examination of the effects of operation of a high airflow, machine mounted dust scrubber unit on face air patterns. Results obtained through a cooperative study with the Peabody Coal Co. demonstrate that new mining cycles can be considered that increase production efficiency while maintaining satisfactory ventilation conditions.

Jan 1, 1986

By F. W. Newhall

DURING the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Browns-ville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to the chairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corpora-tion, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which are presented in this paper. Acknowledg-ments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication.

Jan 1, 1934

By P. Somasundaran, D. W. Fuerstenau

Adsorption isotherms for dodecyl sulfonate on alumina were determined at 45°C and 25°C and the data was used for calculating the partial molar heat and entropy of adsorbed ions under various concentrations. Changes in OH and AS observed at certain concentrations agree with the postulate of interaction of surfactant ions to form two-dimensional aggregates at the solid-liquid interface. Values of the total OH and AS for the aggregation process calculated using the Clausius-Clapeyron equation is used to interpret the interactions of surfactant ions with each other as well as with the solvent molecules.

Jan 1, 1973

By Torres S. Ricardo, Encina M. Víctor, Segura O. Claudio

INTRODUCTION This paper is a conceptual resume of engineering studies that have been evaluated by the Mine Department related to production planning over the next twenty-five years. These studies have been required principally because: a) The Rio Blanco Mine, property of CODELCO- CHILE, Andina Division, faces an operational problem due to heavy snowfall in winter which enters the surface subsidence area of the cave; later melts and filters into the broken ore creating a product that is difficult to transfer through the orepasses. The phenomenon is especially serious during the spring and has been increasing over the years. This element that complicates extraction will be controlled with the procedures proposed or others that may be determined in the future. b) The mine will increase production in 1985 by 40% . LOCATION The deposit is located in the central region of the Andes Cordillera, at an altitude of approximately 3,600 m above sea level, 50 km to the northeast of Santiago. The main camp is Saladillo (at 1,300 meters above sea level) located 30 km from the mine. Due to its location, the mine is subject to heavy snow storms during the year. On many occasions the road from Saladillo to the mine is closed because of storms and avalanches. For this reason the company has self-sufficient civil facilities near the mine to cover the needs and welfare of the working force. These housing facilities are connected to the mine by underground passages. For the same weather related reason the primary and secondary crushers, and the entire concentrator complex are located underground. GEOLOGIC CHARACTERISTICS Geology Based on the geologic model developed for the Rio Blanco deposit and comparing it with standard models pertaining to copper porphyries, it can be concluded that this deposit is part of the apical sector of a mega deposit and therefore the projections of the Xio Blanco cop per mine are very favorable, both in lateral area and depth. In order to confirm and evaluate these geo- logic features, an extensive drilling program was started at the Rio Blanco deposit. Diamond drill holes were drilled to depth as well as in the areas named "La Americana", "Don Luis" and "Elguin". The area explored by the drill program is 3 km long in a north-south direction and 1.5 km wide in an east-west direction. In some sections the drilling in depth reached the 2,300 m elevation mark. The lowermost level in the mine is at elevation 3,070 m. These new studies have permitted the recognition of the following lithologic units: Andesite Andesite Breccia Granodiorites, Rio Blanco and Cascada Granodiorite Breccia Quartzmonzonite Porphyry Monzodiorites and Latites Tourmaline Breccia Dacite Pipe and Rhyolite marginal ring. The mineralogical study permits the definition of three stages of hypogene and hydroterma1 alteration of importance with a time-altered sequence. These stages correspond to a late hydrothermal stage. The kinds of alteration that have been recognized are: Potasic Alteration Propylitic Alteration

Jan 1, 1981

By P. G. Meikle, C. T. Holland

The effect of the condition of friction upon the ultimate unit compressive strength as determined between the compressed faces of precisely machined coal specimens and specially prepared testing platens has been examined. Reductions of 30 to 40% in the ultimate unit compressive strength of these model coal pillars have been verified when lubricants areused between the faces as compared to non-lubricated faces. Increase in unit compressive strength due to confinement at each of three levels of friction appears to follow generally the widely accepted "1/2 power law", i.e. S - C (L/T)1/2 where S is the unit ultimate strength, C is a constant dependent on the coal being tested and the coefficient of friction acting at the compression surfaces and L and T are the least width and thickness of the specimen, respectively. Results suggest that the surface condition of both the specimen and platens should be mentioned in detail in conjunction with compression testing, for although the term (L/T)1/2 is adequate for all practical purposes, the coefficient C is directly dependent on the condition of interfacial friction, all else remaining constant. One phase of the investigation of the confining effect of friction on the ultimate unit compressive strength of small coal specimens has recently been completed at the School of Mines of West Virginia University. The efficient control of ground is of fundamental importance to successful mining operations and the design of support pillars has always presented the mining engineer with a difficult and intriguing engineering problem. Since about the turn of the century, many investigators have performed extensive laboratory tests on small coal specimens in efforts to solve some of the perplexing problems of strata control and pillar action in coal mines. A detailed review of this work would serve no purpose here, but a brief mention of the more significant contributions is in order. Muller16 was perhaps the first to illustrate the effect of confining pressure on the strength of coal specimens in compression. His work has recently been more carefully expanded by the experiments of Murrell17 in Great Britain. Rice and Enzian l9 observed that as the size of cubical test specimens increased, the unit compressive strength decreased. These observations were later supplemented by Lawall and Holland, 13 by Greenwald4,5 et a1 at the U. S. Bureau of Mines, by Gaddy3 as well as by Steart,22 Millard15 et a1 and Evans2 et al. Gaddy3 seems to have been first to quantify this relationship with his equation: S = K/vd , where S - ultimate unit compressive strength (psi), K = a constant dependent on the coal, and D =edge dimension (in inches). Holland7 concluded that the strength of coal as affected by lateral dimensions and thickness could be expressed as where K = a coefficient dependent upon the coal, L = least width of pillar (in.) and T = thickness of pillar (in.). Data supplied by this formula have been compared to the estimated stresses in pillars that had been standing for long periods in coal mines and in the cases so far studied the results indicate that the formula predictions are sufficiently accurate for engineering purposes (Holland11 ). This equation therefore is believed to be the simplest and most accurate tool available at the present time for approximating the strength of a coal pillar (over a specified range of L/T) in situ. However, Holland7,9 has indicated that friction between the coal pillars and the top and bottom rock

Jan 1, 1965

By Arcy A., D&apos Shock

This paper delineates the scope of the developments which have taken place in expanding the utilization of the soluble salt provinces. The location, geology, extractive technology, as well as the growth of uses are reviewed. An expanding recent growth has been in the use of solution cavities for storing hydrocarbons. The development of the technology to obtain and operate these storage cavities as well as the development of the methodology for solution mining of the soluble salts are discussed.

Jan 1, 1985

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By R. F. Sheldon

Largest uranium deposit in the Northwest is Dawn Mining Co.'s Midnite mine on the Spokane Indian B Reservation. The orebodies lie along the contact of granite and metamorphosed sedimentary rock and are controlled by faults and shear zones near the granite contact. In the oxidized zone the deposits consist mainly of the secondary uranium mineral meta-autunite; sooty uraninite and primary uranium minerals are known to occur at greater depths. Elevations in the mine area range from 2500 to 3500 ft. The rolling hills and low, rounded mountains are covered with grass and evergreen trees.

Jan 5, 1959

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955

By C. G. Dunn, M. Sharp

HE orientations of 137 crystals of copper pro-T duced by secondary recrystallization in a cube texture matrix have recently been obtained. Although the crystals were not prepared for the purpose of determining a secondary recrystallization texture, the orientations obtained proved to be rather interesting, as they confirmed, in part, published results and also disclosed additional preferred orientations in the texture. The investigation of Dahl and Pawlek,&apos; Bowles and Boas,&apos; and Kronberg and Wilson3 showed respectively that the orientations of secondary grains growing in a cube texture matrix were related to those of the primary grains by a rotation of approximately 30" about [001], the rolling direction, by 30" about a <111> direction, and by either 22" or 38" about a <111> direction. Kronberg and Wilson also obtained a component of the texture similar to that of Dahl and Pawlek except the angle of rotation about [001] was 19". When the cube texture matrix was deformed a small amount, Kronberg and Wilson also obtained large grains on subsequent annealing corresponding to a rotation of 15" about the normal to the sheet, but these grains should not be classified as secondary recrystallization grains since they were produced subsequent to mechanical straining. The particular texture obtained, of course, depends on the composition of the copper and the processing schedule employed, since these factors markedly affect the primary recrystallization texture and the sharpness of any cube texture produced. In the present investigation, pieces of OFHC copper in the form of M in. round bars were cold forged to a thickness of about 0.40 in., annealed 1 hr at 350°C in an atmosphere of hydrogen, and cold rolled crosswise to a thickness of 0.200 in. These pieces were given a penultimate anneal of 1 hr at 350°C in hydrogen and a 90 pct cold-rolling reduction lengthwise to a thickness of 0.020 in. Indentations generally were put in one end of the as-cold-rolled strips to promote earlier formation of secondary grains.

Jan 1, 1953

By W. D. Douglas, M. J. Hampshire, G. J. C. Young

This paper describes the replacement of a conventional filtration, clarification, and zinc precipitation plant by a carbon-in-pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers early laboratory studies to the design and erection of the full-scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies employed to solve them.

Jan 1, 1985

By Roswell Johnson

THE Manual of the Oil and Gas Industry, under the Revenue Act of 1918, published by the Treasury Department for the guidance of oil companies in preparing their estimates of future recoverable oil for the purpose of calculating depletion, gives the first large public collection of comparative decline curves for the whole country. It is a matter of both scientific and practical interest to so arrange these data that the pools can be readily compared. There are certain difficulties in such a comparison, however: 1. The economic limit varies from 50 to 2000 bbl. a year in different pools taken. (2) Because of this variation in economic limit, the range of data shown makes comparison possible only for wells of intermediate size. In order to be as inclusive as possible, I have taken as an expression of the rate of decline the amount of oil produced in the period during which a well drops from 3000 to 2000 bbl. a year.. No period of smaller production could be used because of the high economic limit in California; and no period of larger production and yet include the small well areas of the Appalachian. As it is, the Lima-Indiana wells are excluded. In a few instances, curves were extrapolated to obtain the reading, where the curve seemed regular enough to warrant it. In general, the amount of oil, in barrels, produced while a well declined from 3000 bbl. to 2000 bbl. a year is shown in Table 1.

Jan 1, 1920

By Frederick N. Rhines

Pure copper that has been allowed to oxidize at an elevated temperature in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cuprie oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig, la). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composetl of oxide particles precipitated in a matrix of metallic copper, that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,&apos; it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but mill separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (I) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By Frank Firmstone

IN the summer of 1881 we were forced to break up and remove the large mass of iron which had accumulated under No. 2 furnace at Glendon, in order to prepare the foundations of the new furnace which has taken its place. We used "Atlas" powder, drilling the holes with a pair of Rand drills. These worked very well when the iron was at all uniform in hardness; but this was not often the case; and it frequently happened that the holes were hopelessly blocked when but little over a foot deep. Good tamping became, therefore very important. The common method of tamping is certainly very dangerous when there is a percussion cap in the hole, and has, no doubt, caused many of the accidents attributed directly to high explosives. We found an excellent and safe method by using plaster of Paris, mixed to the proper consistency and ponred into the holes as soon as they were loaded. Clean dry sand was mixed with the plaster to reduce the quantity needed. With proper attention the tamping would set in a few minutes, and little or no more time was required than for tamping in the ordinary way. We used a "magneto" machine (Laflin and Rand) to fire the holes; and an additiollal advantage in the plan was that any risk of cutting the exploder-wires in tamping was avoided. We found it worth while to load holes not over 13 inches deep in a block 3 or 4 feet thick since the bottom of the hole was enlarged by each shot so that the next time it could be loaded more heavily, and three or four shots in this way often did as much good as a new hole twice the depth, to drill which might have taken ten or twelve hours. The rise in temperature when boiled plaster solidifies is not sufficient to ignite the exploders, as we found by repeated trials before using it in a loaded hole.

Jan 1, 1884

By Forrest F. Craig

Both early and more recent1 laboratory measurements of gas-oil relative permeabilities were made by subjecting oil-saturated cores to external gas drives. In these runs it was generally assumed that the flowing gas/oil ratio was constant at every point throughout the core. Using this assumption, the resulting equation for the gas-oil relative permeability ratio becomes A where Q is the flow rate at the producing end of the system. This relative permeability was then specified for the average saturation of the core. The assumption and resulting equation fail to recognize that in an external drive, the oil flow rate varies from zero at the injection end to a maximum at the producing end. The assumption also fails to consider the existence of a saturation gradient during an external drive. This saturation gradient is due solely to non-steady-state flow. Some authors2,3,4 have used this erroneous method of calculating relative permeability ratios from external drives. Other authors5,6,7 have used relative permeability ratios in calculating expected field performance by external drive, using Equation (1) and making the incorrect assumption that the saturation is uniform within the driven portion of the reservoir. To find the correct relation between the relative permeability. ratio at the average saturation and the produced gas/oil ratio, the insertion in Equation (1) of a factor, F, to adjust it for oil velocity gradient has been considered. The equation then takes the form Assuming that the oil velocity is directly proportional to the distance from the injection point leads to the conclusion that, for a linear system, the average oil velocity is one-half that at the producing end. Thus, the average gas/oil ratio is twice the produced gas/oil ratio, and Equation (2) is transformed into However, here again the existence of a saturation gradient is not recognized. The produced gas/oil ratio is related to the relative permeability ratio at the saturation of the outlet end of the system. It can be shown quite readily that, if the true log k,/k, saturation relationship is linear over small ranges of saturation, then d log kjko Where aaxv and u2 are the average and outlet saturations, respectively. Examination of Equation (3) shows that the factor F cannot have a single value over the whole saturation range. Another method of dealing with external drives is that of Buckley and Leverett.&apos; Their method, which assumes no gas expansion and outlet end effects, considers fully the saturation gradient present due solely to the displacement mechanism during an external drive, and applies Equation (1) to each point along this gradient. The calculation of production history using relative permeability ratio is straightforward. However, the calculation of relative permeability ratios from production history by this method is impractical. In a recent paper, Welge,1 using an approach similar to that of Buckley and Leverett, presents a simplified method for determining the saturation at the producing end of the system. At thi; saturation, the relative permeability ratio calculated by Equation (1) applies exactly, after breakthrough of the stabilizej front. By this method, relative permeability ratios or production history may be calculated with equal ease. Use of this method as a laboratory tool in determination of relative permeability ratios by external drive requires the knowledge of the total injected fluid volume; in addition to the average saturation and producing ratio. As a preliminary test of this method of calculation, laborntory external gas drives were run on a 3% in. diameter, 11 in. long sample of Nellie Bly consolidated sandstone. This core sample had a permeability of 824 md and a porosity of 28.1 per cent. The driving fluid was air. Three different oils were used, having viscosities of 1.4, 9.8, and 125 cp, respectively. The runs were made under identical pressure differentials,

Jan 1, 1952

By G. K. Burgress, H. S. Rawdon, R. W. Waltenberg, J. J. Crowe

The main objects of this investigation were to determine, from neasurements taken at representative rail mills…

Jan 1, 1915

United Engineering Trustees, Inc. W. D. B. MOTTER, JR., &apos;44 A. L. QUENEAU, &apos;45 ALBERT ROBERTS, &apos;43, President The Engineering Foundation GEORGE D. BARRON, &apos;44 F. F. COLCORD. &apos;46 A. L. QUENEAU, &apos;45, Chairman

Jan 1, 1943