Search Documents

By G. L. Schroeder

Investigations were conducted at two underground locations, foreman's room and 5702 area, of the Kermac Nuclear Fuels Corp. uranium mining installation, Ambrosia Lake, New Mexico. The rock environment is stratified sandstone. Pressures were varied from minus 0.4 an Hg to plus 3.8 cm Hg with respect to barometric pressure, and were maintained for periods ranging from several hours to 21 days. One cm Hg overpressure (-1.5% of normal barometric pressure) produced a 20-fold decrease in Rn flux into the foreman's room as compared to the Rn flux observed during dilution ventilation. The 5702 area experienced a 5-fold decrease in Rn flux for a similar overpressure. During 21 days of continuous 1 cm Hg overpressure in the 5702 area this reduced Rn flux was maintained. The smaller reduction in flux for the 5702 area results in part from the proximity of the foreman's room to a non-pressured area and the presence of an impermeable shale lens overlying the ceiling of the 5702 area. A 0.4 cm Hg underpressure of the 5702 area increased the Rn flux into the area by 3-fold over the non-pressured value. A barometric pressure influence on Rn flux into the mine and on air Rn concentrations in non-pressurd areas of the mine was measured. A falling barometric pressure causes an increase in the flux of interstitial gas into the mine; a rising barometric pressure decreases this flux. These effects are not seen in overpressured mine areas. Radon concentrations in rock interstices show, during overpressure, decreases of all locations monitored except in the immediate vicinity of the shale lens above the 5702 area ceiling. These reductions are the result of air flowing from the mine into the rock interstices under the influence of the pressure gradient induced by the overpressure. The relative humidity of the 5702 area was reduced after 2 days of 1 cm Hg overpressure from a pre-overpressure value of 96% to 81%. The control of harmful or noisesome gases which emanate into underground mining areas from surrounding rocks is often a costly necessity. In uranium (U) mines this problem is presented by the high interstitial concentrations of radon-222 (Rn), a radioactive noble gas of 3.82-day half-period, formed in the decay scheme of U238, and the relative ease with which this noble gas diffuses from its parent rock into the interstices of the rock and then to a working area. Long-term exposure to moderate concentrations of Rn (3000 µµc per 1) and its short-lived alpha-ray emitting daughter products, RaA (Po218) and RaC (po214), has been found to result in an increased incidence of bronchial carcinomaa2 The acceptable limit of Rn daughter products in a mine atmosphere is presently set at a concentration of short-lived radon daughters which would be in equilibrium with 100 ppc of Rn per 1 of air. Ventilation of mines is conventionally accomplished by continuously diluting the mine air with fresh air brought in by fan or natural convection from above ground surface. The diluted air is allowed to vent freely to the atmosphere. This process does nothing to retard the rate at which gases (including Rn) diffuse into the mine from surrounding rock. It merely reduces the concentrations of these gases within the mine. It is suggested that in a sufficiently permeable rock environment a slight pressurization of the mine air may induce air flow from the mine into the interstices of rock surrounding the mine. The convective flow of comparatively fresh air will reduce the concentration and the concentration gradient of undesirable gases in the rock interstices adjacent to the mine. Radon will diffuse counter-current to this convective flow at a rate proportional to its concentration gradient. In time, a steady state of convection and counter diffusion will be established. The Rn flux into the mine will never be reduced to zero, and will only asymptotically approach zero as the overpressure (and hence the convective velocity of purging air) approaches infinity. During 1963 and 1964, an investigation into the effect which such applied pressures have upon the Rn characteristics of a mine atmosphere was conducted at the Kermac Nuclear Fuels Corp. uranium mines, Ambrosia Lake (near Grants), New Mexico.

Jan 1, 1967

By Donald F. Irwin

Amid the violent economic changes of recent years that have affected Canadian gold-mining operations so deeply, the discovery and early developments of Kirkland Lake might easily be overlooked. There was more than one "false dawn" for the district before developments finally established the fact of a superb mineralized zone extending through the present operating properties. Never far from the railway, Kirkland Lake has had the benefit of direct rail service for many years. The pioneer discovery on which the first mill and cyanide plant was erected was the "Tough-Oakes," this property being on what is now the eastern end of the producing area; some time later, the "Lake Shore" was discovered at the present center of the district, and a small plant was built upon it also. Both of these early treatment plants were of pre-war design. Progress in gold metallurgy has caused a gradual change in cyanide practice since the early days at Kirkland Lake, which may be observed in the various plants now operating there. From the beginning, it was recognized that Kirkland Lake ores were more responsive to cyanidation than to alternative recovery methods, and that their mineralization contained gold in very finely divided form. Although sulfides and tellurides are present, the quantity is small, being in the order of 1 or 2 per cent by weight, so that gravity concentration is undesirable, since gold is not confined to the sulfides. Some complication is offered by the presence of tellurides, which have caused lengthy controversy over their importance in recovery methods, but which are now generally regarded as less harmful in the light of increasingly high recoveries being obtained. Nevertheless, finely divided gold intimately associated with sulfides in the presence of tellurides; and occurring in the hard Kirkland Lake porphyry ore, substantially free from natural slime-forming constituents, indicates fine grinding. This has been the universal practice although the degree of grinding has varied a little among the different mills and is considerably finer now than formerly. The natural condition as outlined caused the establishment of fine grinding at an early stage in the development of Kirkland Lake, during the period of valuation of gold at, $20.67 per ounce. With the arrival

Jan 1, 1935

Jan 1, 1926

By Irwin Roman

In a previous paper,l a method was suggested for determining the depth to a bed in the simple case of a uniform overlying layer of constant thickness. The main purpose of the present paper is to show how a slight modification of that method has been used to interpret specific data obtained in the upper peninsula of Michigan by the staff of the Depart- ment of Mathematics and Physics of the Michigan College of Mining and Technology. The method of Tagg2 has also been used on the same data, thus furnishing a comparison of the two methods, as well as a method of using the two methods jointly. The method of measuring the apparent resistivity is that suggested by Wenner,3 and illustrated in Fig. 1. A current I enters the earth at the positive pole C and leaves it at the negative pole D. The potential V of the high electrode A, with respect to the low electrode B is measured by suitable means. The separation of the collinear points in the order shown, DBA C, is I, the same for each interval. If the resistivity of the overburden is po, and that of the bed is pa, the apparent resistivity is given by

Jan 1, 1934

By R. Maddin, C. H. Mathewson, W. R. Hibbard

Recent publicationsl.2 establishing the presence of cross-slip in strained metallic single crystals oriented wholly within the area of single slip as predicted from the generalizations of Taylor and Elam3 described these markings as they appeared during the initial stages of the deformation process. At that time, the plane having a common glide direction with the primary slipping plane was reported as the cross-slip plane although the specific direction was not confirmed. Consequently, in continuation of the research, it seemed advisable to investigate the micro-graphic appearance of cross-slip together with the Laue back-reflection X ray analysis and stress-strain data during the later stages of the deformation process. Accordingly, a single crystal of brass (72.75 pct Cu, 0.01 pct Fe, 0.01 pct Pb, 27.23 pct Zn) was polished mechanically and repolished electrolytically after the manner described in the earlier paper.' Three pairs of flat surfaces, parallel to the specimen axis, and (1) perpendicular to the plane containing the pole of the primary glide plane and the specimen axis, (2) perpendicular to the plane containing the pole of the cross-slip plane and the specimen axis, and (3) perpendicular to the plane containing the slip direction and the specimen axis, were polished mechanically and repolished electrolytically, resulting in a final minimum gauge diameter of 0.4864 in. in a gauge length of 3.36 in. The specimen was elongated in tension and load-extension readings were taken following the method described in the initial investigation.' Observed reorientations were obtained from a series of Laue back-reflection photograms at the center and ends of the gauge length and at various positions around the circumference of the specimen. These were interpreted after the manner of A. B. Greninger.4 Cross-slip (Fig 1 and 2) was found with the first appearance of the primary slip clusters and usually joined members of these clusters. In addition, a third set of entirely different markings (Fig 3) could be noted. The displacement of this third set by the primary slip lines was measured as 8300 at. diam (3.04 microns). Since the specimen was carefully observed at high magnifications before any deformation and no markings of any type could be noted, it would appear that this third set was formed during the deformation process prior to the initiation of classical primary slip. Additional extensions produced no unusual change in the appearance of either cross-slip or the third set of markings. The number of lines increased with increasing elongation and appeared, generally, in areas where earlier markings were present. The continuity of the clusters of cross-slip lines in Fig 4, 5 and 6 illustrates that they are neither noticeably displaced by nor do they displace the primary lines at this stage. In Fig 7, cross-slip appears in a long narrow localized band approximately 45 degrees from the stress axis. This somewhat resembles a twin band except for the lack of a sharp boundary. After a shear of 0.257, suffcient additional glide occurred on the cross-slip plane to displace the primary slip lines (Fig 8). Generally, where a large number of cross-slip lines could be observed in an area on one flat surface, few cross-slip lines appeared on the diametrically opposite position on the parallel flat (Fig 9). These, of course, were not matched observations on the same glide ellipses. It was extremely difficult to make such comparisons. The third set of markings (Fig 10) was extensively displaced by glide on the primary slip planes. A plot of the width of primary slip clusters versus their displacement of the third set of lines is shown in Fig 11. The slope and the linearity of the plot suggest that each primary glide plane slips to a constant maximum value of shear before further slip is transferred to another plane. A shear value of 0.28 was determined in this case. Heidenreich5 has presented a similar schematic representation of glide for aluminum. After the specimen had attained an elongation of 51.8 pct, corresponding to a shear of 0.973, cross-slip appeared very prominently in certain areas as shown in Fig 12, yet at diametrically opposite positions very little cross-slip could be noted, Fig 13. Classical conjugate slip was found at this advanced stage in the deformation, Fig 14, which corresponds to the axial location shown at 12 in Fig 15. It should be noted that cross-slip occurs within the conjugate slip clusters and on the same plane as the cross-slip associated with the closely spaced primary lines which constitute a background in less distinct focus. The third set of markings noted at all stages in the deformation of the

Jan 1, 1950

Report of President The important fact of the year 1916 is that on July 25 contracts were executed by which the American Society of Civil Engineers because an additional Founder Society and arranged to make its permanent home in our building. The contracts provide for the construction of three additional stories to the building, the American Society to pay the cost tip to $250,000, this being considered equivalent to what each other Founder Society had contributed, the American Society to participate in the original Carnegie gift and have an equal share in the property with each other Founder society. The construction of the addition to the building is under way, $62,525.04 having been expended thereon in 1916. It has been found that, clue to war conditions and the advanced price of materials, the cost of the addition will be $300,000. The founder societies have been requested to assume the extra $50,000, one quarter each. This work is in charge of a Building Committee consisting of H. H. Barnes, Jr., Chairman, E. G. Spilsbury, Charles Warren Hunt and Charles F. Rand. At the request of the Founder Societies, important alterations were made in the lecture halls on the fifth floor of the building to make the same suitable for social functions of the societies. The cost, $6,642.08, was advanced by the United Engineering Society but is to be paid eventually by the Founders. The Library of the civil Engineers is being merged with the Library of the United Engineering. Society and the other founder societies. At the present time the membership of the four founder societies is 29,000 and of associate societies 23,000, so that a total of 52,000 engineers now have their headquarters in our building. The value of the real estate now owned by this Society is $1,647,171.16. This sum will be increased at the end of 1917 by the amount of the cost of the addition to the building.

Jan 3, 1917

MINING METHODS W. J. COULTER, Chairman P. B. BUCKY, Vice-Chairman CLYDE E. WEED, Vice-Chairman ROBERT S. PALMER, Secretary Alluvial Mining CLINTON BERNARD O. B. PERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANTCHARLES THURMAN Open-Cut Mining Iron. A. D. CHISHOLM EARL E. RUNNER G. E. DIEHL G. E. LEVEQUE P. G. HARRISON SIMPSON RICHEY W. A. STERLING

Jan 1, 1943

By Thomas L. Kesler

Present Raw Materials The lithium industry has had exceptional growth since publication of the last edition of this volume, and the present scale of mining and consumption of raw materials is a great many times that of 1949. The materials of present economic importance consist of four pegmatite minerals and lithium-bearing brine. Spodumene, a lithium pyroxene, occurs in greatest abundance, and is the chief source. It has the formula LiAlSi2O6 and theoretically may contain 8.03 pct Li2O, but in the more important deposits the content is 6.5 to 7.5 pct. The hardness is 6.5, the specific gravity 3.1 to 3.2, and the color mostly pale green to white although deep green, lilac, and yellow varieties exist. The crystals are prisms with strongly developed longitudinal cleavages, and crushing characteristically produces lath-shaped particles. Giant crystals up to 47 ft long are known, but in most occurrences the predominant size range is 0.5 to 12 in. long and 0.1 to 2 in. wide. Hypogene* alteration has formed lithia-bearing sericite and coarser muscovite and rarely eucryptite, while supergene* alteration yields kaolinite and hydrous mica. Lepidolite, of second importance, is a mica of varying composition approximating K2Li3-A14Si7O21(OH,F)3. It has lamellate cleavage, book structure, and a specific gravity of 2.8 to 3. The books range in size from microscopic to a diameter of several inches. The color is mostly violet, but other colors include pink, gray, yellow, and white. Most commercial lepidolite contains 3 to 4 pct Li20 and chemically is in the higher grade range of a series of lithium micas that includes polylithionite, zinnwaldite, and protolithionite. In this series, the content of Li2O is exceptionally as high as 7 pct. Petalite and amblygonite are also of economic importance, but are used in smaller amounts. Petalite has the formula LiA1Si4O10 and is white, gray, or pink. The hardness is 6, the specific gravity 2.4, the cleavage in two planes 114° apart, and the Li2O content commonly 3 to 4.7 pct with a maximum of 4.88. Amblygonite has the formula LiA1FPO4 in which OH may substitute for F to form montebrasite. It is white and has polysynthetic twinning in two directions at 90°. Amblygonite superficially resembles potash feldspar, but has a bluish or grayish tint unlike the cream or salmon tint of the feldspar.[t] The hardness is 6 and the specific gravity 3 to 3.1, and the content of Li2O is the highest among lithium minerals that occur in significant quantity, ranging mostly from 7.5 to 9 pct with a maximum of 10.2. The brine of Searles Lake in California30 has been a commercial source of lithium since 1938. See Chap. 7, p. 108. The "lake" is a saline evaporite deposit, and the exposed part has an area of 12 sq mi. To an average depth of 71 ft, this part of the deposit consists of crystalline salts with 50 pct interstitial voids. The voids are filled with brine that contains mainly sodium and potassium compounds, but the brine also contains 0.015 pct Li2O, which is recovered as dilithium sodium phosphate containing 21 pct Li20. This deposit overlies a

Jan 1, 1960

E. R. Rice, Wickenburg, Ariz. (communication to the Secretary*):—While this paper is primarily intended as a discussion of Mr. Riter's, I think it will be best to indicate my criticism by describing my own field-methods. It has been my experience that, for ordinary work, the regular transit-book is to be preferred to the card-system for recording notes. This is specially true when computations in the field are required, for it is then necessary to have at hand the total latitudes, departures, ancl elevations. Moreover, the transit-book is easier to carry and manipulate in wet or cramped places, and is not as liable to damage as the loose leaf or card. I use a regular transit-book in the field, and then copy my notes, sketches, etc., in an o5ce-book, entering also the latitudes, departures, and other reductions. These values are then copied into the field-book, securing a duplicate record, in case either book should be lost or mislaid. In the field-book, the notes are entered on the left-hand, and the sketches and remarks on the right-hand page. The next two pages are left blank for the latitudes, departures, bearings, reduced distances, etc. Of course, the notes for the different parts of the mine are entered in the field-book in the order in which they are surveyed; but in the they are entered systematically. It has been my experience that the system of keeping notes used by a surveyor, is particularly adapted to the needs and temperament of the individual. Otherwise, he would not be

Jan 1, 1912

By F. W. DeVries

The subject article is an excellent comparison between two potential oxidants, molecular oxygen and hydrogen peroxide, as used in the Palangana field at the time of the trials. The tests showed no advantage to using hydrogen peroxide; however, it would be unwise to generalize that the experience in these trials was universally true. During the time of the work cited, extremely high levels of an unusual impurity were recycling in the lixiviant, which substance was a catastrophically destructive catalyst for peroxide. Since this material was not removed before recycle, it was not surprising that much of the peroxide fed was decomposing in the feed piping and never made contact with the uranium mineralization. Under these conditions, indeed, peroxide showed no improvement over oxygen. This is, however, perhaps the most adverse environment encountered to date in US in-situ uranium leaching. In other operations, peroxide has proved advantageous where two factors have been exploited: 1.Despite the tendency for Hz02 to decompose to water and oxygen in the in-situ leach environment, its higher redox potential before decomposition has provided higher leach rates. In some formulations, overloading beyond the O2 saturation equivalent with peroxide has allowed higher oxidant levels, and higher leaching rates, when overloading with molecular O2, led to vapor-locking.

Jan 1, 1983

By L. O. Howard

MUCH work has been done recently on the lead-antimony system1 in connection with lead-rich alloys of commercial importance containing less than 20 per cent. antimony. Dean, Zickrick and Nix have called attention to the perpetuation in the literature of several erroneous data, such as a eutectic temperature of 228° C. at 12.5 per cent. antimony, instead of 247° at 13 per cent. The series is given as a classic example of a straight eutectiferous series in such late books as those of Heyn and Grossmann,2 Jeffries and Archer,3 Guillet and Portevin4 Pulsifer,5 Rosenhain,6 and Liddell,7 as well as the somewhat earlier works of Hofman (1918), Wang (1909) and Williams (1920). The work of Dean has definitely showed a solid solution of antimony in lead at about 2.5 per cent. antimony. While lecturing to a class in general metallurgy at the University of Idaho, the writer had the students prepare a series of lead-antimony alloys for the purpose of illustrating methods of thermal analysis. Proper proportions of powdered antimony (sold as C.P.) and test lead were mixed and melted in graphite crucibles under a reducing cover. Cooling

Jan 1, 1928

By William L. Fink, Dana W. Smith

Many investigators have attempted to determine the true nature of the internal changes taking place during aging. Merica, Waltenberg and Scottlt were the first to propose a theory of age-hardening. They attributed the age-hardening of duralumin to the precipitation of minute particles of the compound CuA12. Later Zay Jeffries and R. S. Archer2 augmented the above theory by suggesting that the small CuAl2 particles acted as "keys" causing "slip interference." Many other investigators3 have devoted much time to the mechanism of age-hardening, some corroborating the "precipitation" and "slip interference" theory, others coming to different conclusions because of effects that to them seemed unexplainable by the early theories; e.g., the increase of electrical resistance upon aging, the fact that no change in lattice parameter could be detected during the early stages of aging even at elevated temperatures, and the fact that the density did not change as would be predicted. In 1932, Merica revised4 his earlier precipitation theory to take care of these presumably anomalous effects. This revised theory, the "knot" theory, assumes that substantial age-hardening occurs before actual precipitation of solute as discrete particles. The assumed mechanism is one of diffusion of solute atoms into groups forming distorted regions which act as "hard" spots and cause slip interference. These "knots" are assumed to have approximately the same lattice arrangement as the solvent. The anomalous behavior of lattice parameter, density, and electrical conductivity, require a modification of the simple precipitation-hardening theory, only if it is assumed that the precipitation of minute particles during aging has the same effects on these properties as the formation of large particles under equilibrium conditions. Data obtained by the authors in the study of the aluminum-magnesium system5 indicated that

Jan 1, 1936

GENTLEMEN : It is my privilege to transmit herewith the reports for the calendar year 1932 of your Treasurer and the Chairmen of the following Standing Committees: Finance, Admissions, Membership, Papers and Publications, Library, and Mining and Metallurgy. To these reports you are referred for additional details of the year's activities. Finances.-Continuation of depressed conditions in the mining industry (in common with other industries) caused the income of the Institute to decline from $168,274 in 1931 to $138,331. However, economies were effected so as to reduce expenditures from $171,198 to $135,977. As a consequence the net result of the operations for the year was a-surplus of income amounting to $2,354 compared with a deficit of $2,924 in 1931. This gratifying result is accounted for in large measure by the foresight of the Finance Committee in anticipating a substantial decline in income and preparing the budget accordingly. Incidentally, the tentative budget for 1933 has been balanced at $125,000.

Jan 1, 1932

By Harwick Johnson, E. W. Schilling

THE separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordey1. Three years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in the form of curves showing exactly the effect of such treatment were lacking. Probably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines5-7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made7 and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described, but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type.

Jan 1, 1935

By G. W. Jr. Jarman

THE purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electro-static separators and air flotation or air tables.

Jan 1, 1938

By Henry M. Howe

In my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel: the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand us. Iron Molds.—If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag is much greater in the former than in the latter, because in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Jan 1, 1910

By G. H. Clamer

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919

By P. Barnes

In a paper recently read before the Institute by Mr. W. A. Goodyear, a useful presentation was made of the subject of the production of' water-gas on a large scale, by the use of a regenerative form of apparatus. By way of supplement to that paper, a brief statement of the details of a plan which was carried out at the works of the Elgin National Watch Company at Elgin, Ill., may be of interest, 'although the ultimate result of the working of the producer was not successful or satisfactory. This company had decided to build a gas-works for the supply of illuminating gas to their factory, on a much larger scale than that of the petroleum-works which had very successfully supplied the smaller buildings for many years, and in March, 1882, the material for a gas-making cupola furnace was purchased. A few weeks later it was decided to make the attempt to bnrn the gas under the steam-

Jan 1, 1884

By Samuel B. Christy

As is well known, the ore at New Almaden is cinnabar. Native quicksilver occurs also; but, as a rule, in small quantities only. Pyrite occasionally accompanies the ore. Bitumen is quite common,

Jan 1, 1885

According to Vorwärts, the German Mining Commission sent to ascertain the damage done to the mines of France says that the work of restoring these mines will furnish work for all the unemployed in Germany for the next 8 years. The commission said the work of reconstruction would have to be clone from. "the ground up," especially in the Departments of Pas de Calias, Courriere, Lens, Lievin, Drocourt, Mourchin, Carvin, and Dourgas, where the destruction was pronounced "terrible." Most of the mines have been "drowned," and in rebuilding new shafts would have to be protected against the inward pressure of water. The Germans declared the work of restoration would not only be one of great difficulty, but that in many cases it was impossible to ascertain the extent of the damage clone to each mine. They also said it was not easy to fix responsibility for the destruction because it was done by nu-merous groups of troops and the records showing where each military unit was located and at what period were not complete or available.

Jan 12, 1919