Search Documents

By H. A. Hancock, L. M. Pidgeon

Equilibrium carbon monoxide pressures were measured over the reaction between chromium oxide and a number of solid ferrochromium alloys in the composition range 0.4 to 4.8 pct C and 0 to 49 pct Fe. Measurements were also made for the carbides Cr23C6 and Cr7C3 which agreed well with previous investigations. Between 1050°and 1400°C the pvessures varied from 0.1 to 56 mm and increased markedly with the iron and carbon contents of the alloys. The data were used to estimate the activity of carbon in the alloys and to calculate the equilibrium conditions for the decarburization of a useful range of ferrochromium alloys. WHEN ferrochromium is produced by the reduction of chromite with carbon in an electric arc furnace it invariably contains up to 10 wt pct C. For many purposes such as the production of stainless steel, it is necessary that the carbon content be as low as from 0.02 to 0.05 pct. Thus an important part of the ferrochromium industry consists of the production of low carbon ferrochromium. The classical Bessemer steelmaking technique cannot be used to oxidize low carbon contents in chromium and ferrochromium alloys without also oxidizing the chromium. Recently a new commercial process2-4 has been introduced for oxidizing carbon from high chromium content alloys which consists of heating the solid alloy with such oxidizing agents as Cr2O3, Fe2O3, or SiO2 in a retort at reduced pressures. By maintaining the carbon monoxide pressure below the equilibrium value for the system, the carbon can be removed as carbon monoxide without oxidizing the chromium. The equilibrium conditions for the decarburization of solid chromium carbon alloys have been determined by Boericke5 who measured the carbon monoxide pressure over the reaction between the various chromium carbides and chromium oxide. A typical reaction is shown below. Cr23C6 + 2Cr2O3 =u 27Cr + 6CO [1] These values are not applicable to the decarburization of commercial ferrochromium alloys which invariably contain major amounts of iron. The present investigation was therefore undertaken to measure the change in the equilibrium carbon monoxide pressure brought about by additions of iron to the Cr-C-0 system, thus extending the work of Boericke into the region of the production of low carbon ferrochromium. MATERIALS AND METHOD Materials. Measurements were made on two carbides of chromium, Cr233C6 and Cr7C3, and fifteen Fe-Cr-C alloys. The chromium carbides were made

Jan 1, 1963

By Carle R. Hayward

The growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding- and polishing-machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and each possesses some original features which may be of interest. Electric Heating-Furnace. The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Uufortunately, however, even the platinum-wound furnaces cleteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, 3. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with " Excello " resistance-tape, 0.014

Jan 1, 1912

By Frank Drake

Manganese-ores are known to exist in the Caucasus in a number of localities, viz., in the government of Kutais, near the village of Chiaturi; in the same goverilment near the Choruk river, southward from Batum; and in the governments of Erivan and Tiflis. In smaller quantities they are found in various other places also. The first-mentioned deposits are by far the most important; the others being not only less extensive, but remote from present means of communication, and, from their character, expensive to work, although in some cases the ore is of a superior quality. All the manganese-ore now known in the market as a Caucasian " ore comes from Chiaturi, no other deposits in the Caucasus having been worked commercially; movements have been made, however, towards the exploitat,ion of some of those on the Choruk river. The Manganese-Ore District of Chiaturi. General Remarks, Statistics, Etc.—No other known deposit of manganese-ore can approach that of Chiaturi in capacity for producing large quantities of high-grade ore at a low cost. The deposit is said to have been discovered in 1848, by the geologist Abich, but the first shipments were not made until 1879, when 871 tons* were produced. Since that time, the production has steadily increased, until now the world relies on this deposit for about one-half its supply of manganese-ore. The industry is also of great importance locally, and aftords a livelihood to a considerable proportion of the population of the district in which the deposit is situated.

Jan 1, 1899

By J. E. Schaffer

Drilling activity in Ohio increased slightly in 1939. There were 1020 completions as compared to 910 in 1938. During the past six years the number of completions has varied little (Table 1). Oil production in Ohio has been gradually declining since 1896, when the peak production of 23,941,000 bbl. was reached (Fig. 1). Since that date production has slowly declined to an estimated production in 1939 of 3,144,134 bbl., the lowest in 53 years. This total production is divided approximately into the following grades of crude oil: Pennsylvania, 1,185,456 bbl.; Corning, 1,261,615 Flg 1. bbl.; Lima, 578,500 bbl.; Lodi, Based on figures of U. S. .Bureau of 104,740 bbl.; Cleveland, 13,823 Mines and Oil andGas Journal bbl. Table 2 shows the prices paid for the various grades of crude oil.

Jan 1, 1940

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

By R. H. Frazier, F. W. Boulger

THE performance of welded structures is closely associated with the ductile-to-brittle transition temperature of the steel from which they are made. A low transition temperature is desirable because it indicates that the steel is less likely to fail suddenly at low ambient temperatures. Structures such as bridges, ships, storage tanks, and pipelines are usually made from hot rolled semikilled steel. Changes in rolling practice or chemical composition appear to be the most practical methods for improving the toughness of such materials. This results from the fact that production is likely to be seriously curtailed if improvements were obtained by recourse to heat treatment or complete deoxidation. This paper discusses the effect of variations in carbon and manganese contents on the properties of semikilled steels. The transition temperature, a property to which considerable importance is attached, varies with specimen configuration, testing method, and criterion of performance. Both the Navy tear test' and the keyhole Charpy test were used in the investigation. According to the terms used by Vanderbeck and Gensamer,V he tear test was used to measure a fracture transition and the Charpy test to measure a ductility transition. In either case the specimens absorb considerably less breaking energy in tests below the transition temperature than in tests above the transition temperature. Decreasing the testing temperature of notched-bar specimens seems to be equivalent in its effect to increasing the severity of loading on fabricated structures. Therefore, structures built from steels exhibiting lower transition temperatures in laboratory tests are expected to be less susceptible to sudden brittle fractures in service. Consequently, changes in composition which lowered the transition temperature of the experimental steels were judged desirable. Materials and Methods The steels for this study were made in a laboratory induction furnace and rolled to 3/4 in. plate, using a finishing temperature of 1850°F. Precautions taken to insure reproducible melting and testing practices are discussed in detail elsewhere.' All tests were made on hot rolled steels. The analyses of the experimental steels are given in Table I. The list includes steels with manganese contents ranging from 0.21 to 1.46 pct, at each of five carbon levels. The phosphorus, silicon, sulphur, and nitrogen contents of the steels are reasonably constant. The tensile and notched-bar properties of the experimental steels are presented in Table 11. Both upper and lower yield points are listed, and all values are averages for duplicate specimens. Transition temperatures based on three criteria are given. The keyhole Charpy transition temperatures are the temperatures at which the energy-temperature curves based on averages of four specimens cross the 20 and 12 ft-lb levels. Both definitions of Charpy transition temperatures have been used by other investigators. Charpy tests were made at intervals of 10°F, using a pendulum with an available striking energy of 220 ft-lb and a velocity of 18.1 ft per sec. The specimens were oriented parallel to the rolling direction and notched normal to the surface of the plates. The tear test transition temperatures are based on the usual' criterion of the highest temperature at which at least one of four specimens exhibits brittle behavior. The dimensions of the tear test specimens are shown in Fig. 1. The specimen is loaded eccentrically in tension, with pin and shackle fixtures, through the large holes while submerged in a liquid bath at the proper temperature. A specimen developing a fracture area with less than 50 pct shear or ductile texture is classed as brittle. Tear tests were made at intervals of 10°F.

Jan 1, 1955

By S. Frederick Ravitz

FOUR liquids are ordinarily present in the lead blast furnace during lead smelting. At the bottom is the lead bullion, which is metallic lead containing about one per cent of impurities, including gold, silver, copper, bismuth, arsenic and antimony. Above this is the speiss, which consists essentially of arsenides and antimonides of iron and copper. The speiss is followed by the matte, which consists principally of sulfides of iron, copper and lead1. The top layer is the slag, of which the major constit-uents are silica, lime, alumina, zinc oxide and iron oxide. Similar products are obtained from the dross furnace, which treats the dross obtained in decopperizing lead bullion. The distribution of gold and silver among these various products is of considerable importance in the smelting of lead. In general, the matte and speiss cannot be treated in the lead smelter, and usually are sent to a copper smelter. It is usually desirable, therefore, to keep their gold and silver contents as low as possible, and to collect the precious metals in the bullion. If the bullion, speiss, matte and slag exist together in equilibrium, the gold and silver should distribute themselves among these four liquids in a definite manner, which, other conditions being equal, should depend only on the amounts of gold and silver in the charge to the furnace. It is thus apparent that a knowledge of whether such equi-librium exists is necessary before attempting to study the effects of various compositions of matte and speiss on the distribution of gold and silver among the furnace products2. Moreover, systems consisting of four liquids in equilibrium are very rare, and are of considerable scientific interest.

Jan 1, 1936

By Truman Aldrich

THE Clinton group of the Silurian holds the red or fossiliferous ore; its outcrops have been mapped by the State or U. S. Geological Survey. This group is from 100 to 500 ft. thick in Alabama. There are places where it is entirely missing (doubtless islands in the Silurian Sea). In Etowah County, in part of Greasy Cove and vicinity, the upper seam is a coral reef impregnated with the red ore; in this same county, step, faults bring up the ore in three or four separate ridges practically parallel. In Blount County and on Raccoon Mountain, the ore runs under the carboniferous rocks and outcrops in the valleys. In examining some bore holes made in drilling for oil, the writer found the Clinton group continuing under the Warrior coal field wherever the drill has gone deep enough. It demonstrates the possibility of a source for red ore not seriously thought of until lately. The following bore holes made principally for oil, given in Bulletin No. 22, Geological Survey of Alabama, show the presence of either ore or red rock, and suggest vast resources yet to be outlined and developed for ore in the future. The locations are given by number on the map. Hole No. 1 was drilled 6 miles southeast of Russellville, Franklin County, by the Woodward Oil & Gas Co. It passed through 160 ft. of Clinton, but only a small show of red ore was found at 1280-1400 feet. A test well, No. 2, drilled near Atwood, Franklin County, in section 26, township 8, range 14, penetrated the Clinton at 1608 ft. and found 38 ft. of limy red rock, also 8 ft. of some blood red ending at 1820 ft., making 46 ft. of red rock in all. It is reported that some good ore was cut through but this work was done by a churn drill. The hole was continued by diamond drill from here. At least 400 ft. of the formation was classified as Clinton.

Jan 10, 1924

The following list contains the names of members whose death notices have been printed in MINING AND METALLURGY from March 15, 1947 through March 15, 1948 Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns Year of Election - Name - Date of Death - Issue Containing Biography - Page 1938 ABERNATHY, G E , (M) Feb 6, 1948 April 1948 266 1935 ARCHER, M T, (M) Oct 26, 1947 Dec 1947 633 1947 ATIKINSON, JAMES E, (S) Feb 6, 1948 June 1947 309 1940 AYRES, VINCENT L, (M) Oct 14, 1947 Jan 1948 59 1915 BABCOCK, JAMES E , (M) April 1, 1947 June 1947 309 1942 BAGGALEY, WILLIAM BLAIR, (A) Aug 28, 1947 Jan 1948 59 1897 BUIN, II POSTER, (M) Mar 9, 1948 April 1948 219 1945 BAMPFIELD, A E (M) Unknown Mar 1948 215

Jan 1, 1952

By A. W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall, for oreshoots mined were more continuous than drilling indicated. The Geophysics Dept of Michigan Technological University developed a portable induced polarization drill hole probe with a 3-electrode configuration and a sampling radius of 5 ft ±. A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec intervals and readings are taken every 2 ft. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the 1P potential is sampled for 10 ms and recorded. Resistivity (ohm-ft) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous S values noted. The low resistivity amygdaloid contains sills of high resistivity basalt. Verified by core logs, contacts between amygdaloid and basalt could be picked to ± 0.5 ft from resistivity alone. Lithologic logs of long-steel holes, based on resistivity, then replaced sludge logging. An S value of 30 mv/v was established as the lower limit of diagnostic 1P effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found. During the past ten years, the Calumet Div. of Calumet &Hecla, Inc has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings in the Osceola No. 6, 13, 14 and 15 shafts. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling re-

Jan 1, 1964

By Albert Sauveur

This paper explains the possibility of using advantageously a boiling solution of sodium picrate to reveal dendritic segregation in steel. The mechanism of the action of the reagent is described. The failure of manganese alone to produce persistent dendritic segregation is also considered. IRON, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.1 For this purpose, a cupric solution, such as Le Chatelier's, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free., from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters, which represents the same spot as that shown in Fig. 1. The fillings

Jan 2, 1924

By S. J. M. van Leeuwen, R. Feenstra

The effect of jets on bit penetration has been investigated by means of a 50-ton drilling machine and 8½-in. commercial jet bits, drilling under representative bottom-hole conditions. The conclusions apply to the drilling of impermeable rock only. Penetration rate is in all cases primarily hampered by a differential pressure effect, known as dynamic hold-down. Jet action can reduce this slightly. Major gain in penetration rate, up to 25 or 50 per cent, is already ohtained at medium-high jet power. At high bit load, penetration by soft to medium-hard-formation bits is further hampered by bit-balling. Its alleviation requires intensive tooth scavenging, which is best performed by slanted nozzles with trailing, high-velocity, high-volume jets, hitting bottom in front of the teeth. Penetration may then improve by a 100 per cent. At high bit load, bottom-balling limits the penetration of insert-type bits. In this case bottom scavenging is required, which is most effectively performed with high velocity jets from nozzles extended close to bottom. As a result of this measure, penetration may improve 70 per cent in non-friable rock, and less in friable rock. This will make the insert-type bit more versatile. Toothed hard-formation hits suffer at high bit load from both bit- and bottom-balling. Slanted nozzles, possibly much extended, with high-velocity, high-volume jets then have best prospects. INTRODUCTION For years the use of jet bits in oil well drilling has been increasing, in conjunction with ever greater hydraulic horsepower. To the same extent, the need for efficient use of the horsepower has grown.' This paper, it is hoped, will contribute to an understanding of how effective jet action may be obtained. It deals with the effect of jets on phenomena that are known' " to hamper bit penetration. To study this effect, laboratory drilling tests were performed with 8½-in. commercial bits under bottom-hole pressures representative of deep wells. The investigation has been restricted to the drilling of practically impermeable rock. In the following sections, the increase in bit penetration rates due to jetting is discussed for conditions which made the troublesome phenomena stand out one at a time. A brief definition and interpretation of these phenomena is given in Appendix A. Appendix B gives the results of measurements of fluid velocities along the hole bottom, performed in stationary flow tests. Descriptions of equipment, bits, rocks and mud are collected in Appendix C. Unless otherwise mentioned, drilling conditions were kept standard as given in Table 1. CUTTING TRANSPORT TO THE ANNULUS Jet action was for some time believed to merely improve the transport of cuttings from bottom to annulus, resulting in a clean hole bottom. Flow tests performed in 1954 at the Battelle Memorial Institute6 showed, however, that jet velocities of the order of 40 ft/sec sufficed to clear even large (0.4-in.) chips from bottom in the time between two successive tooth actions. In the field, optimum jet velocities are appreciably higher, indicating that other effects must be involved. This much is confirmed by the results of our drilling experiments in soft rocks performed under atmospheric pressure, i.e., in absence of pressure-differential effects. Fig. 1 shows that variation in the nozzle velocity from 40 to 330 ft/sec had no effect on penetration rate, unless the bit penetrated more than 7 mm per revolution, which is about half the tooth height. At such high rates—150 ft/hr at 100 rpm—cuttings would be caught in the tooth cavities, leading to bit-balling, which was noticed on inspection of the bit. The jets thus assisted in keeping the tooth cavities clean. This is just perceptibly reflected in the penetration-rate curves of Fig. 1: Much the same results were obtained in hard rocks with hard-formation three-cone bits. The conclusion is that transport of loose cuttings towards the annulus does not require a powerful jet action. In the following sections we shall see that in deep-well drilling other phenomena are of greater importance. DYNAMIC HOLD-DOWN It is generally accepted that, in deep-well drilling, bit penetration is hampered primarily by the existence of a difference in pressure between the fluid in the hole and that in the rock at the depth of cutting.2-5 In the drilling

Jan 1, 1965

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By Thomas M. Drown

In experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

By Thomas MacFarlane

I. INTRODUCTION. AMONG the industrial enterprises which have, from time to time, been undertaken in our Dominion, few have been more uniformly unsuccessful than those which have had for their object the development of our mineral resources. These resources have not been regarded as insignificant. On the contrary, it is supposed that we possess in our ore deposits something more than mere points of mineralogical interest. Some people are enthusiastic enough to believe that our mineral wealth will yet occasion the establishment in our backwoods of happy and industrious communities, causing, in fact, our wilderness to blossom as the rose. These enthusiasts do not shut their eyes to the serious obstacles which at every stage interfere with the carrying out of mining enterprises in this country, and which tempt one to believe that no such enterprise can ever be conducted to a desirable end, but they entertain the conviction that as our capitalists, miners, and technologists reach the years of discretion, and handle our mines in an economical, vigorous, and judicious manner, and as our statesmen become alive to the necessity of fostering, without extremely protecting, our metallurgical industries, mines and furnaces will gradually prosper, and so develop as to become a tower of strength to our agricultural, manufacturing, and mercantile interests. The fact that our past experience does not generally justify such glowing anticipations makes one all the more anxious to put on record the history of a successful mine, such as the Silver Islet has, on the whole, been. My connection with its discovery and early development was a very intimate one, and I propose in this paper to sketch its history and character, and sum up the amount of silver it has so far yielded. An additional reason for the appearance of this paper is that the Transactions of the Institute contain only a few references to the Silver Islet Mine. Although this mine is reported successful, we have, of course, no guarantee that it will not fall a victim to the same influences which have

Jan 1, 1880

By Arthur L. Hawthorne

10.1-1. Relative Position of Maintenance as Compared to the Overall Mining Costs. The basic issue regarding the importance of maintenance in the modern mining industry must be faced squarely by the top manage- ment of each company before any real progress can be made in organizing a maintenance program for optimum effectiveness. Just a few decades ago the maintenance at coal mines consisted primarily of a blacksmith for sharpening picks and shoeing mules; as a result, probably less than 5%of the total mining cost went to maintenance and some 80% was operating expenses (operating labor). With each succeeding advance in equipment design towards larger, more complex, and more productive units, the pendu- lum swings the other way. As an example, haulage trucks have progressed through various stages in the past 20 years from 15-ton units to a 240-ton truck now in the "shakedown" or experimental stage. The following com- parison between 15-ton, 50-ton, and 100-ton haulage trucks clearly illus- trates this changing cost pattern in terms of percent of overall costs for running each size unit. [Maintenance 24% 44 % 51 % Operating labor 59 % 33 % 16% Operating supplies (fuel oil) 4 %. 4% 3% Labor burden and vac. pay 6 % 4% 3% Depreciation Total] From the preceding figures it is interesting to note that, as a rule, operat- ing costs go down as the equipment gets larger and the maintenance costs increase with the larger units. This same trend in cost variation applies to nearly all mechanical equipment used in surface mining from the large

Jan 1, 1968

By H. L. Gilbert, C. Travis Anderson, W. J. Kroll

IN a previous paper,1 the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.2 When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8in. in diameter. The supply of direct current of high amperage for producing the . desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flexible tubing of the movable electrode, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decided to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 1900°C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica according to the reaction: Si02 + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1948

In our sessions devoted to geophysical prospecting, the greater part of the time heretofore has been given to the presentation of theoretical subjects or highly technical details by specialists directly engaged in the development and perfection of the various methods. This was necessarily so, for we wanted such information available for the benefit of other workers and for our members who were anxious to gain a reliable understanding of the principles involved, to enable them to form an opinion of the adaptability of this new technique to their special problems. The methods have now been actively applied by many reliable organizations for several years and in this period there has been opportunity for operating mining men, engineers and geologists to appraise them. We therefore felt that it would be desirable at this meeting to give some time to interchange of opinion concerning results from actual cases. Consequently, the Committee on Geophysical Methods of Pros pecting sent out letters of inquiry to numerous mining people, asking for frank statements of opinion based on results from geophysical surveys at their properties. We have received many replies, among which 30 or more are of specific interest. On the whole, the point of view is remarkably uniform. Except for one or two who were, perhaps, a bit irritated, the operating men who have replied consider the methods to be capable of yielding valuable information when suitable conditions exist. Their attitude is definitely one of tolerance and of confidence in the integrity and sincerity of the outstanding workers. There is, however, a very general feeling that the chances of attaining positive and trustworthy results are small unless the work is directed by, or at least carried on with the close cooperation of, a geologist or mining man who is thoroughly familiar with the local geologic and mineralogic conditions and with the relations of the orebodies to rocks and structure. From certain comments, I am inclined to think that some operators are not greatly impressed with the cheapness of the work. Probably they are not attaching much weight to cost per acre, but are thinking primarily of total cost in terms of significant results obtained. It is

Jan 1, 1932

By E. M. Porbansky

DURING the investigation of the electrical transport properties of copper, it became necessary to prepare large single crystals of the highest obtainable purity. In an effort to meet these demands, single crystals of copper have been grown by the conventional pulling technique—as has been used for the growth of germanium and silicon crystals.' Low-temperature resistance measurements made on these crystals show that, as far as their electrical properties are concerned, they are generally of significantly higher purity than the original high-purity material. The use of these pure single crystals with very high resistance ratios has made possible the acquisition of detailed information regarding the electron energy band structure of copper2-' and has stimulated widespread effort on Fermi surface studies of a number of other pure metals. It is the purpose of this note to describe our method of preparing very pure copper crystals by the Czochralski technique. Precautions were taken to prevent contamination of the melt from the crystal growing apparatus. A new fused silica growing chamber was used to prevent possible contamination from previous groqths of other materials such as germanium, silicon, and so forth. A new high-purity graphite crucible was used to contain the melt. This crucible was baked out in a hydrogen atmosphere at -1200°C for an hour, prior to its use in crystal growth. Commercial tank helium, containing uncontrolled traces of oxygen, was used as the protective atmosphere. A trace of oxygen in the atmosphere appears to be necessary for obtaining high-purity copper single crystals. A 3/8-in-diam polycrystalline copper rod of the same purity as the melt was used as a seed. The copper rod was allowed to come in contact with the melt while rotating at 57 rpm. When an equilibrium was observed between the melt and the seed (that is, the seed neither grew nor melted), the seed was pulled away from the melt at a rate of 0.5 mils per sec. As the seed was raised, the melt temperature was slowly increased, so that the grown material diminished in diameter with increasing length. When this portion of the grown crystal was -1 in. long and the diameter reduced to less than 1/8 in., the melt was slowly cooled and the crystal was allowed to increase to - 1-1/4 in. diam as it was grown. By reducing the diameter of the crystal in this manner, the number of crystals at the liquid-solid interface was decreased until only one crystal remained. Fig. 1 shows a typical pulled copper single crystal. The purity of the starting material and the crystals was determined by the resistance ratio method: where the ratio is taken as R273ok/R4.2ok. The starting material, obtained from American Smelting and Refining Co., was the purest copper available. Most of the pulled copper crystals had much higher resistance ratios than the starting material. The highest ratio obtained to data is 8000. Table I is an example of the data obtained from some of the copper crystals. Note that Crystal No. 126 had a lower resistance ratio than its starting material and this might be due to carbon in the melt. The melt of this crystal was heated 250" to 300°C above the melting point of copper. At this temperature it was observed that copper dissolved appreciable amounts of carbon. The possible presence of carbon at the interface between the liquid and the crystal will result in reducing conditions and negate the slight oxidizing condition required for high purity as discussed below. The possible explanations of the improvement in the copper purity compared to the starting material are: improvement in crystal perfection, segregation, and oxidation of impurities. Of these, the latter seems to be most probable. A study of the etch pits in the pulled crystals showed them to have between 107 and 108 pits per sq cm. The etch procedure used was developed by Love11 and Wernick.10 The resistivity of the purest copper crystal grown was 2 x 10-10 ohm-cm at 4.2oK; from the work of H. G. vanBuren,11 the resistivity due to the dislocations would be approximately 10-l3 ohm-cm, which indicates that. the dislocations in the copper crystals would contribute relatively little to the resistivity of the crystals at this purity level. Segregation does not seem likely as the reason for purification of the material, since the resistivity of the first-to-freeze and the last-to-freeze portions are approximately the same, as was observed on Crystal No. 124. On most of the crystals that were examined, the entire melt was grown into a single crystal. If the

Jan 1, 1964

By R. I. Jaffee, C. T. Sims, C. M. Craighead

The fabrication of rhenium metal by powder metallurgy techniques is discussed. The following physical and mechanical properties have been measured and are reported: lattice constants, melting point, electrical resistivity, thermal expansion, spectral emissivity, modulus of elasticity, tensile properties and ductility at room and elevated temperatures, work hardening, recrystallization, grain growth, and oxidation resistance. IT is only occasionally that a metal reaches present-day technology with as little known about its properties as element No. 75, rhenium. Relatively scarce to date, it has been studied only infrequently and used less. Previous work on rhenium has been carried out primarily by European scientists. However, realization that rhenium occurs in commercial quantities in the United States recently has focused attention on this metal. Rhenium is a very dense high melting hexagonal-close-packed metal. Like tungsten and molybdenum, its highest oxide is volatile. However, when protected by reducing or inert atmospheres, its strength at high temperatures is greater than that of tungsten. Rhenium work hardens more than any other known pure metal, but, on annealing, becomes quite soft and ductile. Its vapor pressure is approximately that of tantalum, but it does not enter into the so-called "water cycle" nearly as readily as does tungsten. (The water cycle is a deleterious phenomenon causing blackening of lamp bulbs and vacuum tubes with subsequent failure of the filaments.) These and other properties, some already known and some found as a result of the current researches, have indicated that rhenium has many potential uses, primarily of an electrical or electronic nature. Rhenium or its alloys soon may be found in service as electron-tube filaments, cathodic emitters, or as electrical contact materials. In addition, rhenium or its alloys have potential use in such devices as high temperature thermocouples, and high wear-resistant parts such as precision instrument points. Rhenium, in the form of potassium perrhenate, was made available for this study by the Kennecott Copper Corp. The potassium perrhenate was reduced to rhenium metal in two stages, accompanied by leaching to remove potassium in the form of hydroxide. This impure metal was then oxidized to rhenium heptoxide and dissolved in water. The solution was neutralized with ammonium hydroxide to produce highly purified ammonium perrhenate, a typical analysis of which is shown in Table I. The ammonium perrhenate was ground to —325 mesh in a rubber-lined ball mill with Burundum balls. This operation caused a certain amount of impurity pickup, as reflected in the rhenium analysis shown in Table I. The fine ammonium perrhenate was reduced to metal with hydrogen. Particle size of the powder ranged from 1 to 25 microns, as illustrated by Fig. 1.

Jan 1, 1956