Search Documents

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946

By D. W. Philips

THE problem of strata control has of necessity been prominent in mining, and accounts of individual experience and research abound in the literature of most mining countries. Organized research began in Britain by the formation of a committee, upon the recommendation of the Safety in Mines Research Board in 1923, to investigate methods of reducing accidents from falls of roof in coal mines. This committee examined current practice in supporting underground workings in the principal coal fields, and its findings have been published in the Board's publications. Toward the end of these investigations it was suggested by the Chief Inspector of Mines that committees of the several mining institutes be formed to examine the problem in their respective districts. The formation of these committees marked a new phase in research on strata control. The work, though being done in the separate coal fields, followed a scheme outlined by the Chief Mining Engineer of the Research Board, and was coordi¬nated by his office. FACTORS INVOLVED The subject is being considered in Britain from two aspects: I. To provide, by supports, means to prevent falls of fractured ground. 2. To develop methods whereby the strata can be maintained in the least broken condition and thus make falls less likely. The first aspect is the one that will most likely lead to immediate results from the accident standpoint. It depends largely upon the assimilation of already acquired knowledge regarding the proper¬ties of supports and their correct applica¬tion. The second aspect is perhaps more fundamental, and involves also the proper¬ties of the strata and their behavior under the influence of the forces induced by mining. The problem involves many natural factors that cannot be controlled, such as depth, inclination and thickness of seam and nature of the rocks. Other factors, which may be considered to a certain extent controllable, cannot be varied readily and with sufficient fre¬quency to facilitate easy investigation; some of these are: rate of advance of the working face, length of face, direction of the face with regard to cleat and inclination, system and arrangements of rock packing behind longwall faces. In any given case the very many factors present have a mutual influence upon the effects produced in the mine. For example, a study of the effects of rate of advance cannot be done without considering the effects of other factors such as nature of strata, direction of face and quality and arrangement of supports. Conversely, the length and direction of a working face

Jan 1, 1946

By B. M. Larsen, T. E. Brower

IN two previous papersl,2 dealing with the carbon-oxygen reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity 0[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm,; that is, if [C] X [O] is taken as 0.00222, 0[O] = [O] - 0,00222/[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.' This quantity 0[O] proves to be substantially independent of carbon content over the range 0.08 to 1.2 per cent, as well as of the basicity of the slag, and is nearly always within the limits 0.015 to 0.025 per cent when the bath is boiling normally and is in what we have termed a steady state. Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, 0[O], on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in ?[O] level following addition of Spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. VARIABILITY OF EXCESS OXYGEN IN NORMAL OPEN-HEARTH OPERATION The preceding general statements refer to the average value of ?[O] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining oxygen from the gas phase above it, or from added ore, faster than it is losing oxygen to the metal; yet when the bath starts to boil vigorously, the opposite condition may prevail for some time. The consequence of this lag is a variation of ?[O], the interpretation of which in a single heat may not be immediately obvious, This condition is illustrated in Figs. I and 2. In Fig, I, ?[O] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small ore feed causes only a small rise in 0[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1946

By Arthur B. Yates

Diamond drilling has advanced and expanded during the past few yean. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. Control A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing— even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved. however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the

Jan 1, 1946

By J. F. Myers, F. M. Lewis

THE crushing of ore, as defined by Taggart,1 is "usually a stage process, utilizing . . . machines especially suitable for the reduction of particular sizes... . down to a final stage, employed for the reduction of the finest sizes. . .. In contradistinction, comminution to 20-mesh or finer is called grinding. There is a twilight zone in which the product is 6, 10, or 14mesh limiting size which is either crushing or grinding. . .. " Since the data in this paper pertain to a rod-mill operation, comminuting a particular ore size of ¾ in. to a final stage, coarser than 20-mesh, the rod mill is designated as a "fine crusher machine" in this paper. The published literature discloses a wealth of data regarding a rod mill as a fine-grinding machine but relatively little as a fine-crushing operation. Typical of the latter operation is: (I) a description by F. J. Tuck2 in which a fine-crushing rod mill replaced crushing rolls and (2) a description by the present authors3 in which a fine-crushing rod mill was installed instead of a conventional fine-crushing machine. The experience of the authors is that a definite distinction must be made between the rod mill functioning as a fine crusher and as a fine-grinding machine. As a fine-crushing machine it prepares * relatively large amounts of ore for a subsequent fine-grinding operation; as a grinding machine, it grinds relatively small amounts of ore to some predetermined finished product. PULP MOVEMENT AND ACTION IN MILL In considering the work performed by a fine-crushing rod mill, it seems important to understand just what takes place within the mill. We were inspired to study this matter by a paper by E. W. Davis,4 which indicated that definite water classification of ore particles took place in a ball mill. However, in thinking of the rod-mill action from this point of view, we were confronted with the fact that our rod-mill discharge product showed no evidence of action by water classification. The Tennessee Copper Co. ore is relatively high in sulphides, and the gangue rock and the sulphides are of about the same hardness. In the presence of any action by classification, the coarser sizes are definitely very lean in sulphide minerals. [ ]

Jan 1, 1946

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

THE comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined.1,2 These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. COMPOSITION AND FABRICATION OF ALLOYS The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing [ ] from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys will be referred to hereafter by their nominal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedures calculated to produce sheet 1/16 in. thick, cold-reduced by 20, 40, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from l00° to 1500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air- pressure drop p in. water gauge across the airshaft The airshaft pressure drop is calculated by the formula: [ ] wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: [ ] With a combined over-all unit efficiency of the fan and drive of E per cent, the air- shaft power requirements become [ ] There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C$ per kw-hr. the annual airshaft power cost MI dollars per year becomes: [ ] which, expressed by the component parts, becomes : [] The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available monetary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air- shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1946

By F. N. Rhines

I. An Outline of the Theory of the Sintering of Pure Metal Powders SINTERING may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, q, 28, 34, 38, 50, 52, 54 a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." II. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A. The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature.28 Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light contact,"' as do those of many other substances, including nickel." b. Upon compression the strength of the bond is increased progressively.28 There is a limit of pressure

Jan 1, 1946

By W. J. Millard

IT is well known that the excellent mica from Brazil played a most vital role in World War II. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the United States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. TYPE OF DEPOSIT FAVORABLE The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than I:3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. THE ECONOMICS OF STRIPPING When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run II per cent good stain and better when trimmed and contain 2 kg. of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should he used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.I4 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.I5. To this should be

Jan 1, 1946

By Thomas Fraser, H. F. Yancey

PRIOR to the war just ended, Germany was the greatest coal producer in continental Europe. In 1943 the production of coal, bituminous and higher in rank, together with brown coal calculated to the equivalent amount of bituminous coal, is estimated to have been about 240 million metric tons, according to the War Department. Before the war production in Germany exceeded consumption. No other country in continental Europe except Poland had a large surplus. However, England's surplus was the largest in Europe as a whole. Before World War II the Ruhr Basin normally supplied about 70 pct of the total production of high-rank coal, the Saar and Aachen about 6 pct each, Upper Silesia about 14 pct, and Silesia and Saxony the remainder. Nearly one third of the brown coal was produced in the Rhineland, a little less than one half in central Germany west of the Elbe River, and about one fourth east of the Elbe. Bituminous coal and brown coal together constituted by far the most important energy resources of the old German Reich. Bituminous coal furnished nearly 70 pct of the total energy requirement, brown coal supplied about 25 pct, and water power, wood, petroleum and alcohol together aggregated only 7 pct. Because it was the most important single mineral resource of Germany, an excess of coal enabled the Reich to import nearly all the other mineral products that she lacked, such as iron ore from Lorraine. The area adjacent to the coal fields was supplied with gas from an interconnected grid. Similar electric grids are based on brown coal with the power stations at the mines. Coal tar provided the foundation for the development of the extensive German chemical industries as exemplified by the I. G. Farbenindustrie. For almost a century, German scientists have been adequately supported both by the State and by industry in studying improved methods of utilizing coal. In Germany the mineral rights were reserved by the State and ordered extraction of coal was enforced. Each lease comprised a relatively extensive area, which accounts for the generally large size of the mines and mining companies. In 1938 there were 160 mines in the Ruhr, with a total output of 125 million tons but go pct of the production was controlled by 20 companies. By far the largest single coal-mining company in Germany was the Gelsenkirchener Bergwerke A. G., which produced nearly 27 million tons in the Ruhr in 1937. Second was Saargruben A. G., a State-owned company operating in the Saar, which produced more than 13 million tons. Third was Bergwerksgesellschaft Hibernia A. G., with 10 million tons, also in the Ruhr. Briquettes are made from both bituminous coal and brown coal, but in 1938

Jan 1, 1946

By C. G. Southmayd

ANYONE who has been confronted with the problem of predicting the performance of a sand-pump installation is vitally aware of the dearth of precise information that has been published on this important subject. Such data as have been collected are not readily available in a concise and readily usable form, so that many operators would find it a considerable chore to find the pertinent information required to undertake a detailed study. The purpose of this paper is to assemble such established data, correlate them with field experience and outline the factors that must be appraised in the determination of a satisfactory pump installation. The transportation of solids in solution is of vital interest to every mill superintendent and operator, and many of the factors that are involved in this hydraulic problem vary widely from installation to installation, and in some cases even from time to time on any one installation.. These include: type of solids (including shape of particles), size of solids (grind), percentages of fines (slimes), dilution of pulp, contour of pipe line, type of pipe, age of pipe line, effect that diameter of pipe has on characteristic flow conditions, and other factors. Some of these have been fairly well determined by experimental work but many still must be established through interpolating or extrapolating between values that have been derived from known field conditions. Most problems primarily concern the transportation of a definite weight of dry solids from one specific location to another. The type of material, shape of particles, grind and percentages of fines are established and very often the dilution at which the solids must be handled as well. The problem then evolves into a determination of the size, type and contour of the pipe line and the net effective head against which the pump must operate. Before discussing the determination of the head, it might be well to review the interrelationship between the pump discharge (capacity), the head developed by the pump and the pump speed, which will apply to any centrifugal pump installation. EFFECT OF PUMP SPEED Basically, the head developed by a centrifugal pump varies as the square of the pump speed and the discharge as the first power of the speed. However, even at constant speed a centrifugal pump will operate over a wide range of capacities, depending upon the head that must be developed to deliver the liquid or pulp to the end of the pipe line. This is shown graphically in Fig. I. If the pump in question is being driven at a constant speed of 900 r.p.m. it will deliver 500 U. S. gal. per min. against a head of 56 ft., 800 U. S. gal. per min. against a head of 50 ft., and so on. In other words, at this speed the capacity of the pump will be determined and limited by

Jan 1, 1946

By G. Sachs, L. J. Ebert, W. F. Brown

IT is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to the same strength level (i.e., the same tensile strength in a conventional tensile test), However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features-the high speed, the notch, and the bending-the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels3,4,7,8 have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests, In an attempt to analyze the fundamental nature of this test,8 it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom, The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension, This triaxial stress state occurs at a point in the interior of the notch specimen, It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present, This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors, This is contrary to the behavior of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1946

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

[ ]

Jan 1, 1946

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

Jan 1, 1946

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By Marcus A. Grossman

THE institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it," All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we should review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks.

Jan 1, 1946

By R. C. Hyslop

The object of this experiment was to obtain a usable set of field curves for determining the susceptibility of rocks with the vertical magnetometer. The need often arises for determining the susceptibility of rocks in the field in order to interpret magnetic anomalies obtained. This is particularly true when diamond drilling has been done and the relation to the surface rocks of the samples taken is desired. Many methods of measuring rock susceptibility have been developed, but in general they require careful shaping of the sample or pulverizing it in addition to delicate laboratory measuring instruments designed for the purpose. The requirements for a practical method for the determination of susceptibilities are as follows: 1. There should be as little alteration as possible of the specimen. 2. A minimum of time should be required in the preparation of the specimen and the calibration of the equipment. 3. Theequipment used should be portable. 4. An accuracy within the limits of the survey at hand should be obtainable. 5. A means of measuring the remnant magnetism should be available. Laboratory Procedure With these ideas in mind, the problem was approached in the manner in which Koenigsbergerl developed his method using the principle of the electrical theory of images of Lord Kelvin and applying it to the magnetic case. This solution of the problem states that the apparent change in the magnetic field intensity AZ due to the proximity of a specimen is given by: mk AZ = 2a2 Where k is the susceptibility of the specimen, m the strength of the pole of the needle, and a its distance from the surface of the specimen, as shown in Fig. r.2 This relation is true only for an infinite body and corrections are necessary for a finite body. Koenigsberger used in his work a variometer of special design. He suggested that a Schmidt vertical balance or horizontal magnetometer, as well as some other instrument, might be used. The Colorado School of Mines horizontal torsion magnetometer operates on this principle. In the

Jan 1, 1946

[*DAVID THOMAB ...................... 1871 *R. W. RAYMOND .1872-1874 *A. L. HOLLEY ....................... 1876 *Asurn 8. H~WITT ................... 1876 *T.ST~RYHUNT ..................... 1877 *ECKLBY B. COXB .1878-1879 *WILLIAM P. BHINN .................. 1880]

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946