Search Documents

By G. P. Gladis, R. H. Atkinson

Palladium has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items—at least I00 times as rare as gold. Although both visual and spectro-photometric examination demonstrated that the color of Palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400' to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

Jan 1, 1946

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

By E. V. Potter, H. C. Lukens

THE volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.2 Both sets of data show a minimum solubility between 500° and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. There- fore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. APPARATUS AND METHOD The apparatus and method were essentially the same as those described in the previous work,1 as shown in Fig, I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transition points determined under such conditions were less accurate. ABSOLUTE SOLUBILITY Procedure and Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1946

Jan 1, 1946

By M. C. Udy, P. C. Rosenthal

THE use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace, The present study presents the results of a systematic survey of. the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels, Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. EXPERIMENTAL WORK Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. [ ] Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions . was prepared with boron additions in amounts of 0.0015, 0.003, and o,006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two com¬mercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120, Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel scrap were used for melting stock. Deoxidation was carried out in the furnace with o.10 per cent aluminum. The aluminum addition was

Jan 1, 1946

By A. C. Stoddard

Early in the present century, prospect-ing was active in the area of the present Miami district. There were plenty of blue and green copper outcroppings, but very little ore of a grade that would stand shipping costs had been uncovered. Late in the first decade of the century, tunnels were driven into the north and south slopes of the Inspiration ridge, and two of them exposed disseminated copper sulphide ore. This was the original discovery of such ore on the ground of what eventually became the Inspiration Division of the consolidated company. By 1910 exploration of the ground area was well along and by 1911 underground development had been started. In the next few years a large tonnage of disseminated copper ore had been proven— sufficient to justify the expenditure of several million dollars in mine development and for mine equipment plus large sums for treatment plants. The mine and treatment plants were placed in production July 1, 1915. To Jan. I, 1945, there had been produced from the mines of the Inspiration Consoli-dated Copper Co., more than 106,000,000 tons of ore. Nearly all of this tonnage had been recovered by block caving. GeologIcal and EconomIc FActors Block caving is a mining system based on the fact that if a mass of rock has a sufficient number of fractures and planes of weakness the mass will disintegrate if the support of an area of sufficient size is taken away—that is, "undercut." If the material that caves away from the bottom of a block is drawn off the spalling is progressive. There is a limit to the speed of this spalling or caving action, which varies with the structure of the rock being caved. If the rock is drawn at a rate faster than the caving rate, and if this drawing is continued too long, a void may be created that could make a very dangerous condition if the area should drop as a block and force the air below the uncaved rock out through the raises and drifts. This can be a very destructive force. On the other hand, if the broken material is not drawn fast enough the swell of the material in place to broken material would pack the mass until it was almost solid again and could not be drawn without much blasting, or perhaps even partially undercutting again. Geologically therefore it would seem that any rock with seams and fractures would cave; but for block caving there should be enough seams and fractures in a limited area so that such an area will cave and produce a product that can be drawn safely, rapidly enough and at a cost justified by the value of the product being drawn. At the Inspiration the disseminated ores occur in two formations, the Pinal schist and the Schultze granite. There is no material difference in the grade of the ore formed in the schist and in the granite. The chief copper minerals are chalcocite, malachite, azurite and chrysocolla. Other copper minerals occur in limited quantity.

Jan 1, 1946

By G. A. Koehler

The Hiawatha mine, a producer of iron ore, is near the City of Iron River, in Iron County, Michigan. This mine, operated by The M. A. Hanna Co., has been chosen by the author as a typical iron mine in this district that is using the cut-and-fill mining system. General Geology The Hiawatha ore body lies along the steeply dipping north limb of a syncline that closes around on the east end to form a bathtub-shaped structure. Throughout this major structure there are very many smaller wrinkles or folds, which vary the direction as well as the thickness of the ore body. The total length of the ore formation with minor interruptions so far developed is about 3600 ft. The ore body throughout the entire present depth of 2000 ft. has averaged approximately 40 ft. in thickness; it is somewhat narrower at the upper levels and shows a marked increase in thickness on the bottom levels. This increase in thickness probably indicates that the bottom of the trough is near or that a major monoclinal fold has been encountered, which flattens the ore and gives apparent horizontal thickening. The footwall of this ore body is generally a black, graphitic slate, very rich in iron sulphides, quite combustible when exposed to air, and very treacherous to handle during mining operations. The hanging wall, in most places, is a cherty, fairly hard iron formation, and in general stands quite well ill open stopes. There are places, however, where black slate is found in both the hanging wall and the footwall, which makes mining difficult, as the black slate tends to slough off after being exposed to air. In these places it becomes necessary to leave a scale of ore 5 to 6 ft. thick on both hanging wall and footwall, which is not recovered. Fig. I shows a typical vertical cross section through the Hiawatha ore body. Type of Stoping Because of the size and shape of the ore body and the hard, dense structure of the ore, sublevel stoping has been an efficient and economical method of extracting the ore. This method, with various minor changes, has been used since the mine was opened in 1893. There have never been any stope-filling operations, however, until recent years, when crushing of pillars and black-slate fires forced the issue and methods were arrived at to fill all stopes. Development of Deeper Levels Shaft sinking to deeper levels in development operations has been done successfully by two methods without interference or hindrance to production. These systems are: I. Sinking an auxiliary winze a short distance from the shaft, then drifting back to the shaft location and putting up a pilot raise through to the bottom of the shaft. This raise is always in the manway compartment of the shaft, so that no work is ever done under a cage or skip. A 20-ft.

Jan 1, 1946

By Claus G. Goetzel

Pressing of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal iriction. As long as curved surfaces, re-cessej, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more dificult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB) Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. Variable Factors in Molding Powdered Metal Parts Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2:1 would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only 1.5, a compression ratio of 5:1 would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1946

Jan 1, 1946

By L. D. Jaffe, John H. Hollomon

Fox many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure,1 and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearlitic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. QUENCH-CRACKING Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1946

By Paul J. Sirkegian

A detail of the guide rollers is shown on Fig. I; and Fig. 2 shows a photograph of a guide roller that has been in service for several months on the haul-back cable. The former practice of supporting and guiding the haul-back cable on slusher hoists at Kimberly was accomplished by using the conventional type of snatch-block pulley, but it was found that an excessive amount of cable whipping and unreasonable wear on both rope and pulley resulted from this type of cable support. The guide, which is wholly made in the Corporation's shops, consists of two vertical and one horizontal roll assembled in a frame that is lagged to the cap timber in a slusher drift. In some slusher drifts more than one guide-roller assembly is used, depending upon the length of the drift. The installations usually are placed at 30-ft. intervals. We have found by actual experience that these rollers have increased the life of the haul-back cable approximately 200 per cent, as compared with the usage of the conventional sheave-block pulley. Cable Care The underground rigging crew and the slusher operators are trained in rope splicing. No cable clamps or knots are permitted on slusher cables and all cable "eyes" are spliced. The standard practice has been to use preformed cables of ?-in. diameter for haulage and ½-in. diameter for the haul back. The preformed cables have proved to be important factors for safety in use and speed in making splices. No external lubrication is used on the cables. It has been found that dry ropes have about 400 per cent longer life than those that were lubricated under these operating conditions. An accurate record is kept of all cable life and the tonnage moved by the slushers in each working place, and if the rope wear is excessive in any particular working place, an investigation is made to determine the reason. Wire-rope Sling for Snatch-block Anchor The rope sling is shown by Figs. 3 and 4. These slings support the snatch-block pulley for the haul-back rope. The standard practice at Kimberly is to use a roller-bearing snatch-block pulley 10 in. in diameter. The snatch-block housings are equipped with a clevis attachment in preference to swivel hooks, as it has been found that the more rigid clevis keeps the cable in better alignment. The snatch blocks are hung from the cable sling, which is wrapped around the posts of the drift sets as shown on Fig. 3. This method of anchoring the pulley provides better anchorage and flexibility than those of the rigid or spring-mounted types. When the slusher-drift headings are being advanced, the snatch blocks are hung from a "gin" pole ahead of the last set of timbers' An employee is assigned on each production shift to take care of the lubrication of all slusher hoists that are being used and he is provided with tools for minor repairs.

Jan 1, 1946

By F. H. Kihlstedt

THE Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 6o per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in [ ] Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1946

By Walter Stern

The self-potential or spontaneous polarization method is one of the oldest in the field of electrical exploration. When applied in prospecting for ore bodies, it is one of the most rapid and inexpensive means of locating indications of ore bodies at shallow depth. Usually, the procedure is to survey the equipotential lines of the electrical field that is generated by the electrochemical activity of the ore near the ground-water level, and to localize the so-called negative centers or points of greatest negative anomaly. Another field procedure involves the measurement of potential differences along potential profiles, generally laid out at right angles to the assumed strike. Again, in such survey, the basis for establishing the presence of ore is the location of negative potential anomalies. The earlier writers on the subject, notably Schlumbergerl and R. C. Wells,2 did much to clarify the fundamental electrochemical phenomena involved. Interpretation of the field data, however, remained largely qualitative. In 1925, A. Petrovsky3 analyzed the relation between the shape of the potential anomaly curve and size and depth of an Ore body by assuming the subsurface body to be a polarized sphere.' Along similar lines of approach, Edge and Laby5 considered the ore body a dipping sheet with limited extent in the direction of strike, while Poldini6 based the theory on the assumption of a dipping bar. The following study endeavors to enlarge upon these earlier investigations and attempts, on the basis of the potential distribution of a polarized bar, to indicate certain characteristics of the anomaly curve that make possible the determination of depth, size and dip of a subsurface body. The Spontaneous Polarization Field Set Up by an Ore Body If a sulphide ore body is subjected to oxidation varying in degree in its upper and lower parts according to the difference in the concentration of oxygen within the surrounding medium, an electrical potential field is set up. The form and distribution of this field will be investigated herein with special reference to its components on the earth,s surface. Under the simplifying assumption that the ore body may be considered as a dipole with the point sources Q1 and Q2 situated at its upper and lower ends (Fig. I), the potential of the spontaneous polarization at point P is given by the following equation:

Jan 1, 1946

By R. J. Miller, W. A. Bates

ALTHOUGH cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowy1 in 1930, which presented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids ; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. CONSTITUTION AND PROPERTIES Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen

Jan 1, 1946

By R. H. B. Jones

THIS paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recognizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and development. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation.

Jan 1, 1946

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa.* May, '71.. 1 3 2. Bethlehem. Pa Aug., '71.. 1 10 8. Troy, N. Y Nov., '71.. 1 1S 4. Philadelphia, PaFeb., '72.. 117 5. New York, N. Y.*May: '78.. 120 5. Pittsburgh, PaOct., '72.. 125 7. Boston, MassFeb., '78.. 128 8. Philadelphia, Pa.* May, '78.. 2 3 9. Easton, POct., '78.. 27 10. New York. N. YFeb.. '74.. 2 11]

Jan 1, 1946

Jan 1, 1946

The cut-and-fill mining methods in use in the mines of The International Nickel Company of Canada Limited, at Falconbridge Nickel Mines Limited, in the Sudbury District, and at McIntyre Porcupine Mines Limited in the Porcupine District, are typical of the general cut-and-fill practice in both the base-metal mines and the gold mines in the Province of Ontario. The following pages describe the methods in use. HORIZONTAL CUT-AND-FILL STOPING Horizontal cut-and-fill stoping, as practiced in the mines of The International Nickel Company of Canada Limited, falls into two main classifications: (I) transverse cut-and-fill stoping, where ground conditions or wide ore bodies make it necessary to establish narrow stopes and pillars across the width of the ore body; (2) longitudinal cut-and-fill stoping where ore body widths and ground conditions allow safe mining of the full width of the ore body. Transverse Cut-and-fill StopiNg General Stoping Layouts Stope and Pillar Widhs.—For transverse stoping, experience has indicated that narrow stopes and pillars, 27 ft. 6 in and 22 ft., respectively, are most satisfactory. These width are multiples of 5 ft. 6 in., which is the center to center dimension of a standard square set. Thus any stope, or block of stopes, can be readily converted from cut-and-fill to square set-and-fill if ground conditions should warrant such a change. Formerly, pillars were established 16 ft. 6 in. wide, the equivalent of the width of three square sets, with the intention of extracting the pillars by mining an overhand slice one set wide and an underhand slice two sets wide. However, subsequent experience proved that a two-set overhand slice is so much more efficiently mined than a one-set slice, and 22-ft. pillars have been made standard. Chutes.—The stope chutes are established on the longitudinal center line of the stopes and are spaced at 22-ft. centers from footwall to hanging wall. The footwall chute is usually from 5 to 10 ft. from the footwall of the stope. It is offset where necessary at an angle of 52° and vertical chutes are carried from the offset at 22-ft. centers. In sections of the ore body where a flat hanging wall would cut off hanging-wall chutes within a few cuts of the sill, it has proved to be more economical to use temporary chutes or slushers, or both, for these first few cuts, rather than to el permanent chutes at the hanging wall.

Jan 1, 1946

By J. R. Long, C. E. Armantrout, A. H. Roberson, T. R. Graham, R. S. Dean

THE general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing 10 to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heusler1 recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and io per cent Al but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 [ ] has drawn a hypothetical boundary for the alpha field with few data to support such construction. The binary systems involved have received considerable attention by numerous investigators, and their general features are well established. The hopper-aluminum system (Fig, I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smiths established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig. 2) has been recently reviewed by Dean and co-workers.7 Using high-purity alloys, they place the solubility of alpha man-

Jan 1, 1946