Search Documents

Jan 1, 1943

By Carl G. Hogberg

DURING recent months, the acute shortage of steel scrap has necessitated the use of higher percentages of hot metal in the open-hearth charge. With these higher percentages, the sulphur content of hot metal has become an increasingly important factor in the control of the quality of steel. Thus, the blast-furnace operator is faced with a demand not only for more output but for a higher quality of product. More than go per cent of the sulphur charged into the blast furnace is contained in the coke. With the tremendously increased demand, the trend of coke quality has been toward higher sulphur, higher and more variable ash, and poorer physical characteristics. This has been brought about by less selective coal mining, increased production rates in coke plants and resumption of operations of many beehive ovens. In a single month last year, one blast-furnace plant in the Pittsburgh district operated with coke obtained from 52 sources. The effect of variability and quantity of coke ash on blast-furnace operation is well known. The improved results obtained with furnaces operating on coke made from washed coals compared with results on coke made from raw coals is ample proof of the effectiveness of low and uniform ash. Coal-washing plants, however, require a large capital expenditure, and are impractical for most of the large number of small producers, whose operations are confined chiefly to periods of abnormally high demand. Furthermore, not all coals are physically adaptable to washing. PRINCIPLES OF IRON DESULPHURIZATION IN FURNACE Although investigations of the blast-furnace process have not clearly revealed the detailed mechanism of iron desulphurization within the furnace, they have been sufficiently extensive to permit a postulation of the following general principles: I. Iron, in its travel from furnace top to hearth, continues to pick up sulphur until it has reached tuyere level. The zone of iron desulphurization is relatively narrow, being confined to a vertical distance extending approximately from tuyere level to the iron-slag interface in the hearth.1 2. Combustion of coke is confined to spherical zones extending approximately 40 in. from the nose of each tuyere.2 Coke ash is released as the coke burns in these combustion areas. 3. With a constant amount of sulphur in the charge, the sulphur content of the metal product is a function of hearth temperature, final slag analysis, slag viscosity, and slag volume. Both hearth temperature and slag analysis affect slag viscosity. For a slag of constant analysis, viscosity always decreases with an increase in temperature;

Jan 1, 1943

By Walter L. Maxson, Fred C. Bond

SINCE the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. STANDARD BALL-MILL GRINDABILITY TESTS The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill in all tests is 700 c.c. of the packed minus 6-mesh roll product, and the number of grams occupying 700 c.c. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter. Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I ½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity to be expected from a given mill is calculated by comparing the

Jan 1, 1943

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :'paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By W. W. Weigel

The mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. Geology The, basement formation in 'the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 fl. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Milling is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds The district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

By Carter S. Cole

Mr. Chairman, Fellow Members and Guests, our chairman this morning got over into the geneological field, so perhaps I may be pardoned if I revert to some of my ancestral training and give you a text. I always like to talk about some special little text that may illustrate what we want to say. So the text that I will take for this afternoon is a very simple one, "Win the War." That is the guide for all of our actions, or should be. We should question everything we do to see what it does to contribute to winning the war. If we fail to do that, nothing else is going to count. On the wall of the office of one of the branch chiefs in the Copper Division in Washington there is a little slogan which I think we should take very deeply to heart, "The difficult we do right away. The impossible takes a little longer." I think that is a very good guide for us to follow in the work that lies ahead of us in the metallurgical field and in the handling of these secondary metals and the things that result therefrom. My subject is "Conservation and Specifications." Some people would wonder just where that fits in, and how you might define "conservation." One very good definition would be "the utmost use of our resources." If you will pardon my going back to some of my earlier experience for a little simile, those of you who know me know that for ten years after the last war I was in the railroad business. If we are with the engineman in a cab, and we have a green signal ahead of us, that is a clear signal and tells us to proceed at full authorized speed. Now suppose we come to a yellow signal that is caution, slow down to one-half authorized speed and be prepared to stop. Now if you do slow down, the chances are that that obstruction that was ahead of you will move out of the road, and you may get another yellow or caution signal at the next block, and be able to keep going at a slow speed. As of the date of Pearl Harbor our tin supply took on a very yellow tinge, and it threw the caution sign right in our faces. If we had not heeded that sign, and cut down our consumption of tin, we would not have any today; but because we have done so we are in a much better position today than we were a year ago, that is comparing our visible supply with our present rate of consumption as contrasted with the visible supply a year ago and our then rate of consumption.

Jan 1, 1943

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Fred C. Bond, Fred T. Agthe

When some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material. and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media during normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many commercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an important one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain laboratory tests were made from which it was found that different materials form coatings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qualities, like coal and graphite. In general, the softer materials tend to coat at coarser sizes than the harder or more brittle materials. Limestone, as an example, will coat more readily than quartz, even though limestones of different- texture and composition exhibit great differences in coating potentialities. Various materials were tested in the laboratory to show the variation in coating qualities. It was found that in most tests quartz must be ground to a fineness that would permit it to pass through 325 mesh before coating became markedly detrimental to the grinding operation. Siliceous rocks, however, tend to coat more readily than quartz. Granite, which is composed essentially of feldspar, quartz and mica, has been found to start coating at about 92 per cent through 200 mesh, and feld-spathic minerals alone usually show a tendency to coat at the same fineness. Barite has been ground in the laboratory to a fineness of 99 per cent through 325 mesh without showing serious coating of the grinding media. Gypsum coats readily. Apatite and phosphate rock usually tend to coat. Hematite usually coats, although when mixed with charcoal it does not do so. In testing the carbonate rocks and minerals, it has been found that burned magnesite, dolomite, and dolomitic limestone coat, whereas calcite and calcined calcite do not coat so readily. It has been found that commercial glass, slate, talc, steatite and coke have little tendency to coat. The relative tendencies toward coating during grinding operations, exemplified by

Jan 1, 1943

Jan 1, 1943

DAVID THOMAS 1871 R. W. RAYMOND 1872-1874 A. L. HOLLEY 1875 ABRAM S. HEWITT 1876 T. STERRY HUNT 1877 ECKLEY B. COXE 1878-1879 WILLIAM P. SHINN 1880 WILLIAM METCALF 1881 RICHARD P. ROTHWELL 1852 ROBERT W. HUNT 1883 JAMES C. BAYLES 1884-1855 ROBERT H. RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B. POTTER 1888 RICHARD PEARCE 1889 ABRAM S. HEWITT 1890 JOHN BIRKINBINE 1891-1892 H. D4. HOWE 1893 JOHN FRITZ 1894 J. D. WEEKS 1895 E. O. SPILSBURY 1896 THOMAS M. DROWN 1897 CHARLES KIRCHHOFF 1898

Jan 1, 1943

By George M. Fowler, R. E. Illidge

Part I. Developing BY GEORGE M. FOWL INTRODUCTION The Tri-State district comprises an area of about 2000 square miles in southwestern Missouri, southeastern Kansas, and north [ ] eastern Oklahoma. The part that is in and contiguous to Missouri is still sometimes designated as the Joplin district (Fig. I). EARLY OPERATIONS Mining operations in what is now the Tri-State district date from about 1848 and have been continuous to the present. Apparently the first discoveries of ore were made about the same time near the present sites of Joplin, Oronogo, and Granby. Lead minerals were found at grass roots, probably in shattered rock in shallow excavations, then these minerals were followed in shear zones to deeper horizons. The mining of zinc followed. Before 1874, zinc ore was worthless and discarded as waste. According to published records, the total production of lead to that date was 49,000 tons of metal from 70,000 tons of concentrates. PRODUCTION The aggregate ore production from the Tri-State district was recorded at interval

Jan 1, 1943

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By G. L. Craig

In order to meet the unprecedented demand for copper it has proven necessary not only to develop every primary source, but also thoroughly to exploit the vast reservoir of metal in use that is not directly serving the war effort. To accomplish this, industry has been called upon to use its resourcefulness for developing methods of recovery that have not been previously utilized. It is in this connection that we have been asked to review the methods suggested for recovering the basic constituents of various types of the so-called clad or composite steels. As a background for a discussion of recovery processes, it seems appropriate to consider clad materials in general and their processes of manufacture. A composite steel has been defined as one consisting of two or more component parts of which the smallest shall comprise at least 3 per cent of the total mass. Clad materials or composites are produced commercially by several different methods of which the most important may be classified as: I. The Blacksmith or Forge Weld Method. This method is limited to carbon steels or low-alloy steels as the presence of even small amounts of common alloying metals prevent the formation of a satisfactory weld. The principle is the application of pressure to sections in contact at elevated temperatures. Because of the tendency of the iron to oxidize, borax is generally used as a flux to absorb the iron oxide. 2. Casting Process-In this method a composite ingot, billet or cake is produced by pouring one metal onto or about another. The bond may be accomplished by the action of the molten metal against a solid, in which case the bond may be referred to as mechanical; while in other instances alloying occurs at the interface producing an anchor by the formation of component parts of the two materials. 3. Cementation Process.-In this process any number of combinations of metallic and nonmetallic constituents which are mixed together may be used as a bonding agent. The combinations, whatever they may be, are placed between the materials to be joined and subjected to pressures at elevated temperatures to produce the desired bond. 4. Fusion Welding Processes.-Gas and electric joining for direct use or subsequent fabrication. 5. The, Assembly Process.-This method involves the joining together of prefabricated bars or plates followed by hot and/or cold working the assembly to the desired finished form. This method is advantageous in many cases because of its flexibility on small quantities as compared to the casting method. It is also possible to control the relative proportion of components more accurately. In this discussion we are concerned only with the scrap resulting from the manufacture of clad materials and our interest,

Jan 1, 1943

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

Jan 1, 1943

By E. C. Carris

THE particular field of application of machines utilizing air cur¬rents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful com¬mercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the Ameri¬can Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Heyl and Patterson oscillating table, 199.7. 4. "Stump Air-Flow," pulsating air jig, 19391. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAN TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corpora¬tion, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943

By J. W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By Earl S. Greiner, Eric R. Jette

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943