Search Documents

Jan 1, 1942

HAVING described and taught you the method of assaying silver for gold in the preceding chapter, and therein having proceeded in the order and Drover wav followed in the working of quantities of gold and silver, I could have fled this task of describing to you the first part of parting. In truth, there is no other difference in the method of arriving at the end except in respect to certain precautions that must be taken against the dangers causing loss. In order that you may guard against these, I shall repeat the procedure completely, in addition to the second part of this art, which is the method of reducing the silver to its body.

Jan 1, 1942

[ ]

Jan 1, 1942

BECAUSE it is necessary that the powders made for casting have a magistery of salt water, I wish now to teach you to prepare the salt that must form this magistery, for without it these powders would not have the toughness to hold themselves together when they are dry. In short, you take the quantity [119v] of salt that you need to prepare and put it in a rough pot, either baked or, if it suits you better, raw but well dried. This is completely covered with a lid or is luted with well- made moulding clay. Then it is encircled with brick ends at a distance of three dita, like a drying furnace. This space is filled with good charcoal; fire is applied and it is left to stand until all the charcoal is consumed by itself* Then you take that quantity of this burned or rather melted salt which you wish to use for moistening the clay and which you think can be dissolved in the water so that it wd remain very salty. It is boiled in a pot with water and then left to stand. After it has settled, your powder is moistened with it and used for moulding. When you see by testing it that the powder stands up as you wish, it is good. If not, give it some more of this water again and continue until you see that it holds enough. For without this magistery it would return to the dryness that it had before as a powder, and you could not use it without fear that it would fall from the Games. In this way this earth, either natural or artificial, is prepared and made ready, and it is used as the need occurs.

Jan 1, 1942

By Michael Perch, Charles C. Russell

Nearly 95 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69,9, and in 1938 it was 61.3, To produce a net ton of pig iron 1959 lb. of coke was required in ,1940 and 1760o lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1942

BECAUSE gold is a compound mineral praised by philosophers and all wise men as being of the highest perfection among all mixed minerals, and because of its great beauty, it is the universal opinion that it possesses extraordinary powers which are beneficial to man. For this reason it is the thing esteemed most highly in this world, after living creatures. Hence, I, too, in order to honor it, wish to begin by speaking of it now rather than of any of the other metals, and I wish in particular to tell you of its generation and of its most obvious qualities, for, although it is a metal very widely known and one that is desired and sought after by all kinds of persons, I know of few who take the trouble to find out what its substance or natural form may be. But, in order that you too may not be one of those who know it only by name or by the appearance that it shows outwardly to us, I tell you that its original and peculiar materials are none other than elemental sub¬stances, with the quantity and quality of each proportioned equally one to the other and very finely purified. From this union of elements which are of equal force there is born a pleasing and perfect elemental mixture,* and then after fermentation and decoction the elements finally become

Jan 1, 1942

PASSING over the derivation of the word as well as the description of the alum that has been written of as a liquid and that was once called natta, I tell you that the alum that is commonly called rock alum today is a congealed earthy substance, clear and transparent, of a hot and dry nature, and of a bitter taste with a certain unctuous saltiness. It has an astringent and corrosive property and is drawn from mineral stones by means of art. All that I have seen is of the same nature but of two colors,

Jan 1, 1942

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8.9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3-s in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6.9 The measure of internal friction adopted here, I/Q, is (p) X the logarithmic decrement, a measure used by some writers, and is also (I/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°°C. As shown in Fig. i, the internal friction increased by only a factor of 2 from room temperature to 300°°C., then by a factor of 100 during the next :too' interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction ~ e-HI/RT [I]

Jan 1, 1942

MELTING in a hearth and in a basket is almost the same thing; charcoal and bellows are used for both. These are made large or small according to the quantity that you wish to melt, and more or less force of the bellows is applied according to the need. The hearth, bowl, or refinery, as the masters call it, is made with bricks and clay like a forge; opposite the middle of the tuyère a round hole is made like a wash- basin, wide at the mouth and narrow at the bottom where there is a hole for emptying it. A little iron plug is put in this so that it may be closed when necessary, or a piece of brick that is cut and pointed. Now, when this has been well covered all over with ashes, and the tuyère has been arranged so that the wind strikes the center, it is first filled with charcoal and baked very well so that the metal may be kept hot once it has been melted. When it has been baked, it is again filled with charcoal, fire is applied, and it is left to inflame gradually by itself. Then put one or

Jan 1, 1942

By Philip B. Bucky

[ ] FOREWORD THIS symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge,

Jan 1, 1942

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By C. Zener, H. Nielsen, D. Van Winkle

THE internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. EXPERIMENTAL METHOD The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress. The general method of making such measurements, and of observing the temperature of the specimen during a measurement, has been described elsewhere.5,6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and 900 cycles per second. SPECIMENS The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alphabrass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n ½ where n is the mean number of grains per square millimeter. EXPERIMENTAL RESULTS This paper is concerned exclusively with the part of the internal friction that becomes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

SINCE I have told you of the distillation of waters and the extraction of oils from things-all ingenious and useful processes-I wish to continue to speak of the arts. I am reminded that I first wish to write down for you the discourse that I made to you on another occasion a few days ago concerning the operation of a mint, so that if you have lost it from your memory (and this would not be surprising since you have had no practice in it) you may repossess it if you should need to practice it or even to talk about it, and if you find yourself in this activity it may not be new to you. I told you, as I believe you will remember and so again I repeat, that a very great and constant diligence is required by one who wishes to operate a mint well, or to have it operated, because it has many parts which it is necessary for anyone who enters this work to understand very well; indeed, if he wishes that all the work of his helpers be done well, he will have to do it himself. And if it were possible, he should have a hundred hands and a hundred eyes together, and at the same time should be in different places, because some loss often occurs in what is handled because of the carelessness of the workers or because of their little real trustworthiness. It is understood that such things require great hard labors and many kinds of knowledge. The material handled in this work is most often either gold or silver all ready to be spent, and these things are very attractive to those who handle them. In addition to being made into pieces of money likely to disappear, it is very easy to lose, and whatever part is lacking for any reason whatever [132v] brings detriment and loss to the patron since it is a thing of value. Therefore, in short, anyone who wishes to exercise this art well, without being fraudulent therein, must watch the weights with all care because the essence of this art is naught but the division of a quantity of weight into many exactly defined pieces and the alloying of gold by carats and of silver by leghe, exactly established in accordance with what the prince grants you as remedy.* If through negligence you exceed in perfection

Jan 1, 1942

Jan 1, 1942

By Hugh S. Spence

The use of natural feldspathic rocks, as opposed to straight feldspar, for ceramic purposes is not new. "Cornwall stone," a semi-kaolinized granite containing fluorite, has long been used by the English pottery trade instead of feldspar, and "Carolina stone," a similar rock, is now being offered to the American trade. A recent report of the U. S. Bureau of Mines states that trachyte, a glassy volcanic rock, is being used in California instead of feldspar in ceramic bodies. In Germany, phonolite and basalt have been investigated, and possibly also used, as ceramic raw materials, and extensive research has been conducted in Russia in recent years looking to the utilization of the immense bodies of nepheline syenite of the Kola Peninsula, which is the host rock of the apatite deposits now being exploited on a large scale in the Murmansk region; the nepheline is recovered as a by-product of the concentration of the apatite. Long used principally as a raw material for the pottery and allied industries, where, in bodies, glazes, enamels, etc., it serves as a fluxing ingredient and forms, on firing, a glassy bond with the more refractory clay, flint and coloring particles, feldspar has been finding ever increasing employment in glass. In 1936, over half of the nearly quarter of a million tons of feldspar sold in the United States went to the glass trade. Its usefulness for this purpose is due to the resistance to thermal shock which it imparts to glass products, particularly bottles, containers and tableware, because of its alumina content, which averages from 16 to 20 per cent. Active search has been wade on the American continent during the past few years for other minerals of feldspathoid type, with comparable or higher alumina content, that, may be suitable for glass and other ceramic purposes. One of the most important results of this work has been the delimiting in central Ontario of large bodies of nepheline syenite of excellent, ceramic grade.

Jan 1, 1942

Jan 1, 1942

By W. A. Bruce

THIS paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to sell-spacing problems are shown.

Jan 1, 1942

By S. E. Buckley, M. C. Leverett

The production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. Introduction Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,l and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. Role of Dissolved Gas When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually. contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1942

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,12, 7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 3 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By F. L. Burchard, Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Coolie, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. DevELopments during 1941 Nearly 1600 wells were drilled in the district during 1941 as compared with more than 1700 in 1940. However, the ratio of successful drilling operations was higher and some 1200 oil wells were completed. Production held about even with the previous year, as did the number of producing oil wells. Known oil reserves increased slightly throughout exploration, which generally was carried on at greater depths than in former years. The average depth of discovery wells was 300 ft. deeper than in 1940. Although discoveries were evenly divided numerically between horizons above the base of the Strawn series and those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the increase in oil reserves. The largest single addition to the reserves was in the Ellenburger formation in the K.M.A. field. During the year 112 wells were completed in this horizon, bringing the total developed acreage to some 4600 acres. The Straan series in K.M.A. also received considerable development in 1941, with 114 completions. K.M.A. Pressure Maintenance Satisfactory progress was made by the K.M.A. Pressure Maintenance Association in 1941. At the end of the year, 99 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 340,548 M cu. ft. in December from a low of 208,853 M cu. ft. in February. Total volume of gas returned during 1941 was 3,306,052 M cu. ft. To the end of the year, 150 cu. ft. of gas had been returned for every barrel of oil produced from the reservoir while the input ratio for December was 397 cu. ft. Per

Jan 1, 1942