Search Documents

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William C. McCulloch

INTRODUCTION The particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 25,400,000 tons of bituminous coal were cleaned by air machines during 1965. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 19 16, by the Sutton, Steele and Steele Co, Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., seven other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine. 2. Arms "Concentrator," oscillating table. 3. Hey1 and Patterson oscillating table. 4. "Stump Air-Flow," pulsating air jig. 5. "Super Airflow," pulsating air jig. 6. Ridge air jig. 7. Phillip air jig. While not all coals can be beneficiated by air washing, the air washing of coals that are easy to clean can be readily proved advantageous. Of all the preparation methods, pneumatic cleaning is the most acceptable from the standpoint of delivered Btu cost. This is based on the premise that a percent of moisture is just as detrimental as a percent of ash. The principle of dry concentration has never been determined with scientific accuracy. To the present time the study has been more of an art than a science. It is possible to forecast the results of wet concentration from a study of the washability characteristics of the raw coal but only after applying rule-of-thumb methods of interpretation to the specific gravity and size distribution can it be ascertained that the raw coal is amenable to dry concentration. Air as a separating medium dates back to biblical times as exemplified in the winnowing of chaff from the grain. However, the same application of air to coal serves merely to blow the dust away and size the remaining particles. Pulsating air was the solution to the problem and largely eliminated the necessity for close screen sizing which was required on early separators. Because of the low density of air, a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. Also, the

Jan 1, 1968

By R. H. Tien

This paper presents an analytical solution of the problem of freezing of a semi-infinite slab with constant surface temperature; in this analysis accoz~nt is taken of the heat evolution during the solid-state transformations in the frozen skin. The regions where transformations occur are treated as plane isothermal heat sources; i.e., the rates of transformations are assumed to be infinite. In the model considered, three plane heat sources are assumed to be present in the frozen solid. The solution yields the temperature distribution in the solid, the rates of movement of the heat sources , and the rate of movement of the solidification front. It is shown that, although the sum of the heats of transformations in the solid is about 20 or 43 pct of the heat of fusion of iron or manganese, respectively, the effect of the heat evolution in solid-state transformations on the rate of solidification is insignzficant. IN several recent mathematical studies of solidification of liquid metals'-3 no account was taken of the heat evolution accompanying the solid-state transformations. In the case of, for example, steel, there are several phase transformations 6 -y, y -a, and the magnetic transformation. Whether or not a significant error is introduced into the mathematical simulation of solidification processes by the omission of the heat effects associated with these phase transformations is not known. The purpose of the present study is to investigate the effect of these phase transformations on the temperature distribution and the rate of solidification based solely on the heat transfer point of view. That is, for the sake of simplicity, freezing of a pure metal with solid-state transformations will be considered. The mathematical model which represents the present problem includes four moving heat sources representing freezing and phase transformations, 6— y — a — ferromagnetic. The thermal properties such as conductivity and specific heat, and so forth, are different from one phase to the other. But they are considered to be uniform over any particular phase. The usual Fourier heat flow law is employed. The concept of conservation of energy is applied at every heat source in order to estimate their rate of movement. The temperature distribution in the solid and the positions where transformations occur are expressed analytically in terms of error function solutions and four coefficients which are determined from four nonlinear algebraic equations. These coefficients can be calculated either by trial and error or by any numerical method. MATHEMATICAL ANALYSIS Fig. 1 is a schematic diagram showing the zones of different phases 1, 2, 3, and 4 in the solidified portion of a semi-infinite pure liquid metal. The heat is subtracted from the system at x = 0 which is maintained

Jan 1, 1968

By B. A. Cheadle, K. P. Steward

Axial tensile, ring tensile, closed end burst, and free end burst tests were done at room tempe.vature and 300°C on three batches of Zircaloy-2 sheathing zuith different textures. Knoop hardness tests were also done on all batches. The mechanical properties of the tubes were largely dependent on the percentages of cold work, but were also markedly affected by the textures, particularly with respect to deformation behavio'r. The deformation behavior observed confirmed Picklesimer's predictions, zuhereas Knoop hardness results could be correlated with texture and yield strength anisotropy after the ,method of Wheeler and Ireland. From the mechanical properties, and from efjectiue strain values deterrlzined at the fractures using a photoqid technique, it zuas concluded that tubing witlz a single preferred orientation of radial basal poles best combines strength and ductility for any given deqee of cold work. THE mechanical properties required in collapsible Zircaloy-2 fuel sheathing for water-cooled power reactors are strength to resist wrinkling deformation by coolant pressure and ductility to accommodate a small amount of deformation in service without rupturing. Zircaloy-2 tubing during fabrication develops pre- ferred orientations of the a Zr grains due to aniso-tropic deformation behavior, and these textures markedly affect mechanical properties. Picklesimer' had predicted the deformation behavior of tubes with various textures, but the texture required to provide the optimum strength and ductility for a given degree of cold work has not been reported. To investigate this problem, tests at three transverse to axial stress ratios were done at room temperature and 300°C on three batches of Zircaloy-2 tubing covering a wide range of textures and percentages of residual cold work. Knoop hardness values were also measured to correlate with preferred orientation and yield strength anisotropy after the method of Wheeler and relland.' 1) MATERIAL For this investigation, three batches of tube-reduced tubing were chosen from the Zircaloy-2 sheathing produced for the Douglas Point Reactor. Individual tubes were 191/2 in. long, 0.600 in. OD, and 0.0165 in. nominal wall thickness. The identities of the batches, together with their textures, are shown in Table I. The tubes had the normal Zircaloy-2 composition3 of 1.5 wt pct Sn, 0.3 wt pct Fe, Ni, Cr combined with the following oxygen concentrations: Batch VII 1140 to 1390 ppm 0 Batch VIII 1400 to 1750 ppm 0 Batch IX 880 to 1320 ppm 0

Jan 1, 1968

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.'-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott' first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber's,' but which does not

Jan 1, 1968

By J. H. Anderson, G. A. Parks, B. K. Jindal, H. Leslie Bullock

H. Leslie Bullock (Engineering Consultant, Oak Park, 111.) — In reading over the paper, I find that I have no quarrel with the thoroughness of investigation of the points studied, but I am forced to question the selection of oxides from oxides as the subject of the investigation, the inclusion of silica gel as an example, and to question the validity of some of the conclusions. Separation of oxides from oxide, in minerals where the liberation of values is possible by grinding, are comparatively rare. Most oxides are only slightly soluble and the action of carbon dioxide or other acid forming ingredient in the air must be added to humidity to produce surface action. Silica gel is a very special synthetic substance in which the adsorption is determined by total surface, pore dimensions and temperature. Quartz is our most prevalent oxide and its action in electrostatic separation is far more sensitive to its three thermal transition points than to humidity.

Jan 1, 1968

By Steve H. Carpenter, Henry E. Otto

The explosive welding of metals is dependent upon the production of a jetting action caused by the collapsing of one metal plate against another. Successful welds are generally accomplished if the yield strength of the metals is in the range of 10,000 to 90,000 psi and the sonic velocity of the metal is greater than the detonation velocity of the explosive if direct contact explosive is being used.' Should the detonation velocity exceed the velocity of sound in the metal it may still be possible to obtain the jetting action and a good weld. However, in most cases where a high detonation velocity is used complications arise because of reflected shock waves which tear the bond apart as fast as it is put together.' Explosive welding of lead presents several problems since its yield strength and sound velocity are very low. Various values have been published3-5 for the velocity of sound in lead ranging from 2000~ to 23004 m per sec. Most of the high-order explosives have detonation velocities on the order of 6000 to 8000 m per sec, which precludes their use. The dynamites have a lower detonation velocity of around 2800 m per sec which is still somewhat too high. Lower-order explosives such as ammonium nitrate (1070 m per sec) must be used to weld lead in the as-received condition if the explosives are used in direct contact. Rather than use low-order explo'sives it was decided to alter the sonic velocity of the lead. The sonic velocity is directly related to the modulus of the material according to the following expression: Fig 1—Interface of explosive weld of lead to steel. Lead is on top As-polished Magnification 75 times as well as the yield strength. Bolling et al. 6 show that the shear modulus of lead single crystals increases from about 0.72 X1011 dynes per sq cm at 300°K to about 0.98 X1011 dynes per sq cm at 0°K, an increase of approximately 3 5 pct. This gives an increase in the sonic velocity of around 700 m per sec. Hence, the sonic velocity of lead at cryogenic temperatures is approximately equivalent to the detonation velocity of the low-order dynamites. We have obtained high-quality lead to steel explosive welds using a 40 pct dynamite in direct contact with the lead. Prior to detonation the lead was chilled with liquid nitrogen (78°K) to increase the strength and sonic velocity. Welds were made while the lead was cold. Specimen sizes were 3 by 6 in. A preset angle of 5 deg with a 0.10-in. standoff at the base was the geometrical setup used. The amount of explosive used for optimum welding of an 1/8 -in. -thick lead sheet to a steel plate was found to be 7 g per sq in. A PETN sheet explosive line wave generator was used to insure a linear detonation front through the dynamite. A photomicrograph of a lead-steel weld is shown in Fig. 1. The typical wave effect that constitutes a good explosive weld is present. When tested in shear, the weld failed in the lead, indicating that the bond is stronger than the lead base metal. Higher-order explosives were also tried without success. We believe this indicates the importance of matching the detonation velocity and the sonic velocity for successful explosive welding. Note Added in Proof. High quality explosive welds of lead to steel have recently been obtained at ambient temperature using a low velocity (1000 M per sec) free running dynamite. The weld interface obtained is comparable to Fig. 1. 'S. H. Carpenter, R. H. Wittman, and R. J. Carlson: Proceedings of the First International Conference of the Center for High Energy Forming, Syracuse University Press, syracu.se, N. Y., in press. 'A. HI Holtzman and G. R. Cowan: Welding Risearch. Council Bull., No. 104, April, 1965. 'Metals Handbook, 8 ed., p. 1062, Metals Park, Ohlo. 'J. M. Walsh, M. H. Rice, R. G. McQueen, and F. L. Yarger: Phys. Rev., 1957, vol. 108, pp. 196-216; 'L. V. Al'tshuler, K. K. Krupnikov, B. N. Ledener, V. I. Zuchikhin,

Jan 1, 1968

By Everett D. Jackson

The largest deposits of chromite in the United States occur in tabular layers in the lower part of the Stillwater Complex, Montana. Nearly 900,000 long tons of chromite concentrates have been produced from mines and mills in this area, and reserves equivalent to more than 2,500,000 long tons of Cr2O3 remain in the ground. Layered concentrations of chromite (known as chromitite zones) occur only within olivine-rich layers of the Peridotite member of the Ultramafic zone of the Stillwater. As many as thirteen chromitite zones, lying conformably one above another, have been found, but only five of them are thick enough to be of any conceivable economic interest, and only two of them have been mined to date. Individual chromitite zones can be recognized by their distinctive internal character and by their stratigraphic position in the Peridotite member. The chemical composition of chromite varies consistently between and within the different chromitite zones. The zones range in thickness from about an inch to more than 12 feet, and the Cr2O3, content of their chromite ranges from 36.6 to 49.2 weight per cent. In any given area, the G chromitite zone is the thickest, but the chromite of the H chromitite zone has the highest grade. Laterally, the thickness of the chromitite zones is related to the thickness of the Peridotite member; in general all are thicker in the eastern part of the Stillwater than in the western part.

Jan 1, 1968

By R. Taggart, R. H. Ericksen, D. H. Polonis

MarTENSITIC a has been observed to form spontaneously from the retained ß phase during the preparation of thin foil specimens of metastable Ti-Cr alloys containing from 6.9 to 20 wt pet Cr. Similar spontaneous martensite reactions have been reported in thin foils of 0 brass' and other alloys.2 4 The absence of retained austenite in iron-based alloys has also been attributed to spontaneous decomposition during thinning.5 The present work indicates that a unique situation occurs during which the spontaneous transformation takes place when the transitional ? phase is present in the as-quenched or partially aged ß phase. Alloys containing 6.9, 7.0, 8.0, 12.0, and 20.0 wt pet Cr were prepared by the levitation melting of "io-chrome" chromium and iodide titanium. The 0.5-in.-diam ingots were vacuum-annealed at 1000oC, and wafers 0.020 in. thick were then cut from the ingots. These wafers were wrapped in molybdenum foil, encapsulated in Vycor under a reduced pressure of purified helium, and then held for 30 min at 1000°C. The specimens were quenched in water to retain the metastable high-temperature ß phase. The quenched alloys were thinned by mechanical grinding to about 0.005 in. thick, then electropolished in a solution of 300 ml methyl alcohol, 175 ml n-butyl alcohol, and 30 ml perchloric acid at a temperature of -40°C. Needle specimens 0.005 to 0.010 in. diam were taken from each ingot and heat-treated with the foil specimens. X-ray diffraction patterns indicated the structure of the 6.9, 7.0, and 8 wt pet alloys to be a

Jan 1, 1968

By Ogden Tweto

The classes of ore deposits in the mountain province of Colorado that have been the most productive in the past and that offer the greatest promise for the future are: (1) disseminated or stockwork molybdenum deposits associated with Tertiary stocks; (2) combination precious- and base-metal veins in Tertiary volcanic rocks; and (3) base-metal replacement deposits and veins in Paleozoic sedimentary rocks. Veins in Precambrian rocks, including precious metal-bearing sulfide veins, gold-silver telluride veins, and tungsten veins, have been mined extensively in the past, but their aggregate output has been far subordinate to that of the groups named above, and the outlook for major output from them in the future is poor. Principal ore deposits of south-central Wyoming are sedimentary iron ores of Precambrian age and uranium deposits in Tertiary sedimentary rocks. Precambrian deposits of several kinds are scattered through the mountains of both states. The most promising of these, based on present indications, are vanadiferous titaniferous magnetite in southern Wyoming and southwestern Colorado and thorium-niobium rare-earth deposits associated with alkalic intrusive complexes in Colorado. Most of the mining districts of Colorado are in the Colorado mineral belt, a generally narrow but somewhat irregular belt that extends northeastward across the north-trending mountain ranges and the north-northwest trending geologic grain of the state. The belt is characterized by intrusive rocks of Laramide and younger age and by ore deposits, and it occupies environments ranging from Precambrian crystalline rocks through Paleozoic and Mesozoic sedimentary rocks to Tertiary volcanic rocks. Two ages of intrusion and ore deposition recently have been recognized in the mineral belt. One is Laramide (late Cretaceous and early Tertiary), and the other is Oligocene. As interpreted herein, the major replacement deposits and most of the sulfide vein deposits in Precambrian and sedimentary rocks are Laramide in age, and the molybdenum deposits, the tungsten and the gold telluride veins in Precambrian rocks, and the precious- and base-metal veins in volcanic rocks are Oligocene in age. In general, the Laramide deposits are mesothermal in aspect, and the Oligocene deposits are principally epithermal. The existence of two mineralization stages, in considerable part characterized by different suites of metals, has many applications in exploration.

Jan 1, 1968

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By J. H. Reynolds

The possibility of using a semiconductor, metal, semiconductor structure as a light detector is discussed. A brief theoretical argument is presented which predicts that this structure should have pho-toresponse characteristics similur to those of a metal-semiconductor diode, but with the magnitude of the current increased by a transistor gain factor. Measurements made at low frequencies on a particulur S-M-S device agree u~th this prediction aizd shoul that significant gain factors are attainable. The current gain is substantially higher than that predicted for the metal base transistor. It is proposed that the operation of these units is more closely approxinzated by the metal-gate model which predicts higher current gains. A qualitative discussion of its high-frequency performance indicates that detection of light modulated at microwave frequencies by a S-M-S deuice is possible. ADVANCES in the technology of chemical vapor deposition'-4 have made it possible to form a S-M-S structure consisting of a thin metallic layer sandwiched between layers of single-crystal semiconductor. It has been proposed5-7 that, if the metal layer is made sufficiently thin, this structure could be used in an amplifier having several advantages over presently available transistors including higher-frequency performance. Calculations8 predict that the maximum gain-bandwidth product is nearly an order of magnitude higher than that of a bipolar transistor having the same geometry. Maximum oscillating frequencies in the microwave range are predicted. Electrical measurements made on S-M-S devices have shown that, although the theoretical frequency characteristics are not presently attainable, current and power gain is obtained. Another possible application of the S-M-S structure is its use in a light detector. This structure is a three-layer relative of the metal-semiconductor diode. Light detection using M-S diodes is the subject of considerable present interest. They are known to have a short response time and the ability to detect light having a photon energy below the semiconductor bandgap. In this paper, the mechanism by which S-M-S photocurrent is generated is discussed. An expression is derived which shows that the response characteristics are similar to those of a M-S diode, but that the magnitude of the current is increased due to the transistorlike behavior of the device. The results of low-frequency response measurements on a particular S-M-S structure are presented. These agree with the theoretical predictions and show that significant gain factors are attainable. A qualitative discussion of the high-frequency characteristics is presented which predicts that detection of light at microwave frequencies by a S-M-S device is possible. THEORY In this discussion, the photocurrent, iT, measured across terminals attached to the semiconductor emitter and collector layers is related to the current pho-toemitted from the metal base layer. The latter will be referred to as the primary photocurrent. The behavior of the primary photocurrent is determined by the characteristics of the two metal-semiconductor diodes. The diode photoemission is illustrated in Fig. 1, which shows the emitter and collector potential barriers. The metal thickness has been greatly exaggerated. As will be discussed later, the actual barrier shape can be much more complex, but this diagram illustrates the essential features of the photoemission process. An absorbed photon having an energy greater than the barrier height can emit an electron into the emitter or collector. Since this process is discussed

Jan 1, 1968

By Wilbur I. Duvall, James F. Devine

7.4-1. Introduction. Ever since explosives were discovered and developed for mining purposes, there has existed the problem of determining what effect the air and ground vibrations resulting from blasting have on structures of various types. This problem is especially acute for surface operations such as open pit mines, quarries, and construction projects that are in the proximity of residential districts, scientific laboratories, or other vibration-sensitive structures. Because the general public is directly involved in the blasting vibration problem, it has been of major concern to local, state, and federal governments, as well as to mining and construction companies, explosive manufacturers, insurance companies, and scientific investigators. Consequently, many investigations have been conducted, both in this country and abroad, on the effects of air and ground vibration on residential and other structures. E. H. Rockwell made some of the first studies in this country on the vibrations produced by blasting and the effect that these vibrations have on structures (18). In his publications, he stressed the need for measuring the vibrations from quarry blasting in order to establish the level of vibration as a function of charge size and distance. The concept of a damage criterion for structures was developed shortly thereafter, and a displacement of less than 0.03 in. was considered safe. During the period from 1939-1942, the Bureau of Mines conducted an extensive investigation on the problem of seismic effects of quarry blasting. This work, summarized in Bulletin 442 (20) was the first major effort for establishing damage criteria for residential structures based on experimental data. An acceleration of less than 0.1 g was considered safe, 0.1 to 1.0 g was caution, and greater than 1.0 g was damage. This work

Jan 1, 1968

Jan 1, 1968

By R. C. Ku, A. J. McEvily, T. L. Johnson

AS reported in a recent paper,' we attempted to measure the response to stress of as-quenched Fe-Ni-C martensites (Ms of -35°C) in both the micro-and macrostrain regions. To avoid effects associated with the diffusion of carbon, tensile specimens were quenched from room temperature at 78°K and tested after 15 min in situ. It was assumed that the transformation had terminated and that the retained austenite was essentially stable. In the tensile tests microplastic strains of the order of 10"* were measured at stresses below 20 ksi. It was concluded that the observed strains were due to the motion of dislocations in the martensite, the dislocations having been introduced during transformation. It was argued that transformation or plastic deformation of the retained austenite did not contribute to the non-elastic deformation measured in the microstrain region. In contradiction to the above argument, Magee and paxton2 have more recently shown that the strain due to isothermal transformation of retained austenite to martensite can contribute to plastic deformation at low stresses even at 78°K. Moreover we were unaware (nost)-a culpa) of a paper by Machlin and cohen3 in which it was clearly shown by resistance measurements that isothermal transformation at 78°K leads to the formation of an additional 1 pct or so of martensite after the initial athermal transformation, even in the absence of external stress. We have verified Machlin and Cohen's results in the following manner. A capacitance microstrain gage was placed on a tensile specimen before immersion in liquid nitrogen. After 15 min at 78°K detectable burst phenomena had ceased and it was then possible to obtain a continuous record of the additional extensional strain due to spontaneous isotherma1 transformation. The results for the Fe-Ni-C series studied are shown in Fig. 1, and are similar to those of Machlin and Cohen who investigated a low-

Jan 1, 1968

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.' In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.' The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968

By John C. McDonald

CONTROLLED cold work is used between solution heat treatment and precipitation heat treatment for producing certain tempers of the commercial aluminum base alloy 2219 (designation of the Aluminum Association, U.S.A.) which contains 6.3 pet Cu as the major ingredient responsible for the age hardening. The complete composition limits for this alloy are listed in Table I. The alloy has been described in detail,' and the control of the heat treatment has also been published.2 Beneficial effects of such cold work in other alloys have also been pointed out.3'4 NO data have been published on the effects of varying amounts of cold work under fixed aging conditions. In connection with an investigation of the possibility of providing the desired cold work by explosively generated shock waves, it became desirable to investigate the effect of variable cold work, and to compare the re -sults with those obtained from explosives. The general principles of explosive hardening are well-described in the literature.' All material used was guaranteed by the supplier

Jan 1, 1968

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic location or seam characteristics modem raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality and these objectives may be sought by commencing the preparation of coal underground at the "working face." Underground preparation involves choosing those portions of the bed which can be cleaned to satisfy predetermined market requirements involving (1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1) seam under development, (2) mining equipment available and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another the (1) petrography of the coal in the bed does not re- main uniform, (2) character of roof and floor are subject to change and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content and petrography are of considerable interest and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal. The prospecting and evaluation of any area containing one or more salable coal beds by means of channel samples taken from outcrop openings and/or from diamond-drill cores can yield valuable data on coal characteristics. By correlating the data developed from distinct petrographic sections of channel and/or drill core samples, the quality of the bed according to stratification will be evident. There are few coal beds that do not show wide variations of such characteristics as ash and sulfur

Jan 1, 1968

By G. Y. Chin, W. L. Mammel

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain has been analyzed by Taylor and by Bishop and Hill. The Taylor analysis is based on a principle of' virtual work, and involves finding, among numerous cotnbinalions of slip systems that satisfy the imposed strain, the combination in which the sum of the glide shears is a minimum. Previously, Taylor has treated the case of axisymmetric flow when slip occurs on (111)(110) (or {110)(111)) systems only. His analysis has now been extended by computer methods to the cases of slip on {112}(111) and {123)(111) systerns and of mixed slip on {110), {1 12), and (123) planes with a common (111) slip direction, all of which are important in the deformation of bcc crystals. The results are computer-plotted as contours of the ratio of the floe strength to the critical resolved slzea-r stress for slip, for axial orientations distributed throughout the standard stereographic triangle. Implications of the computer results to texture develop,merit, texture hardening, and dislocation theories oj work hardening are discussed. WhEN a single crystal is extended in the usual tension test, the lateral dimensions can change relatively freely. In this case, the glide shear produced by slip on a single slip system is sufficient to accommodate the (tensile) deformation. Since slip is governed by a critical resolved shear stress law (the Schmid law'), the single active slip system is one for which the stress, resolved on the slip plane and in the slip direction, is the highest among the several equivalent slip systems. This amounts to saying that a value M = U/t = y/~ is a minimum among the equivalent systems, where M is the inverse of the familiar Schmid factor (a and E refer to tensile stress and strain, and T and y refer to resolved shear stress and shear strain). A grain embedded in a polycrystalline aggregate, on the other hand, cannot freely change its shape due to constraint from its neighbors. In this case, slip from five independent slip systems (to accommodate five independent strains) is generally required.' Based on the principle of virtual work and assuming that the critical resolved shear stress for slip is the same for all systems, Taylor hypothesized that, among all combinations of (five) slip systems which are capable of accommodating the imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Again, this is equivalent to saying that the value of M = CjlyjI/ is a minimum, in analogy to the single slip case. Taylor aminimum,analyzed the case of {111)(110) slip for fcc metals, and applied the analysis to crystals undergoing axisymmetric flow, that is, the same macroscopic shape change as the poly crystalline aggregate under uniaxial tension (or compression). For the twelve equivalent {111}( 110) slip systems, there are 384 independent combinations of selecting five systems to satisfy the five independent linear equations of imposed strain.4 Taylor calculated the value of M for each combination* and obtained the active com- *A number of the independent combinations were omitted from consideration in Taylor's original work (see Ref. 5). bination (minimum M) for a number of axial orientations distributed throughout the standard stereographic triangle. Later work by Bishop and Hill*'8 showed that Taylor's least-shear hypothesis was equivalent to a maximum work principle which they advanced. Using the simplified Bishop and Hill method for {111)(110) slip, Hosford and Backofen' obtained detailed contours of constant minimum M for the same axisymmetric flow case. In contrast to {111}(110) slip in fcc metals, slip in bcc metals is generally described as occurring on {ll~)(lll), {112)(111), {123) (111) systems as well as mixed slip composed of all three. Since the direction cosines of the slip plane normal and the slip direction enter as a product in the Taylor analysis, the Taylor solutions of ,M for {110)(111) slip are identical to those for { 111} 110) slip. The other three cases of slip, however, have not been solved. In view of the numerous combinations of slip systems involved in the calculations, the Taylor analysis is clearly oriented toward computerized solutions. THE TAYLOR ANALYSIS In order to obtain the active combination of (five) slip systems by solving for the minimum value of M = we first express the (small) strain components E,, with respect to the cubic axes 1, 2, 3 ([loo], [010], [001], respectively) of the crystal, in terms of the sum of the glide shears yj from slip systems j: where n, and n,j refer to direction cosines of the slip plane normal, and dri and dsi to direction cosines of the slip direction, of slip system j, all referred to the cubic axes. In practice, the strain components are given with respect to the specimen axes X, y, 2. These components are readily converted to ers through the tensor transformation where irk and 1,~ are the direction cosines between the two sets of coordinate axes.

Jan 1, 1968

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,' catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.' have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968