Search Documents

By A. C. Fraker, H. H. Stadelmaier

WIENER and Bergerl reported the existence of the nitrides Fe3NiN and Fe3PtNwith a cubic L1'2 structure. The present note shows that a similar nitride Fe3PdN can be observed and that the composition range between the iron nitride Fe4N and the nitrides Fe3NiN, Fe3PdN, and Fe3PtN is occupied by single-phase cubic nitrides with structures intermediate between L1' and L1'2. The materials used in this investigation were electrolytic iron of 99.9 pct purity, carbonyl nickel of 99.7 pct purity, sponge platinum of 99.95 pct purity, and palladium sheet of 99.8 pct. purity. Binary alloys of the transition metals were induction-melted in a crucible of fused alumina, powdered, and screened to a particle size of - 200 mesh. The powders were nitrided at 600°C in a gas mixture of ammonia and hydrogen, and the crystal structure was determined with the aid of a Wilson powder camera. The results are compiled in Table I together with information from the paper of Wiener and Berger.1 The compound at the nominal composition Fe3PdN has a diffraction pattern with prominent reflections of a face-centered cubic lattice (h2 + k2+l2 = 3, 4, 8, 11, 12, 16) and weaker superstructure lines (h2 + k2 + 12 = 1, 2, 5, 6, 9, 10, 13, 14). With decreasing palladium content the superstructure lines become weaker and approach the intensity of those of Fe4N. No analysis was made of the intensities, but it can be assumed that the structure is that found by Wiener and Bergerl in Fe3NiN and Fe3PtN, namely L1'2 (perovskite structure) with both palladium and the interstitial nitrogen fully ordered. The dependence of the lattice constant upon the solute atom (Ni, Pd, Pt) content can be explained tolerably well by simple lattice expansion due to subsequent work confirms this suggestion, it will be of significance to order-disorder theory. The author is grateful to Lester Guttman for discussions on this topic.

Jan 1, 1961

By J. W. Rutter, K. T. Aust

Observations are presented of the formation of annealing twins during the growth of a recrystallized grain into a striated, melt-grown crystal of high-purity lead. The formation of an annealing twin resulted in replacement of the original migrating boundary by a large-angle grain boundary of the caincidence-site type or by a near-twin boundary. The results support the Fullman-Fisher theory of annealing twins and demonstrate the usefulness of the coincidence-site model. FULLMAN and Fisher1 have advanced the following theory to account for the formation of annealing twins during grain growth. Whenever a grain A grows into a matrix of grains S1 and S2, a twin A' of grain A may form, as shown in Fig. 1, if the following energetic condition is satisfied: where "E" and "a" refer to the specific interfacial free energy and the area, respectively, of the boundaries indicated by the subscripts. In effect, the twinned grain will persist when the energy of the boundary between the twin(A') and the matrix grain (S, or S,) is less than that of the boundary between the original growing grain (A) and the matrix grain by an amount which exceeds the energy of the coherent twin boundary between A and A'. Experimental observations on the changes in grain boundary free energy accompanying the formation of twins1 are in agreement with the theory outlined in Eq.[l]. Direct observations of the formation of annealing twins at moving grain corners1"3 and the depend-

Jan 1, 1961

By S. Y. Ezz

The quality and extent of fluidization of fine iron ore beds with gases were investigated. Factors affecting the rate of reduction with H, and the sintering of the partially reduced material were studied. Trials to retard sintering by covering the particles' surface with nonsintering materials were successful. THE gaseous reduction of iron ores is a gas-solid reaction. Hence the fluidization technique seems ideally suited to it. However, a serious drawback

Jan 1, 1961

By Irving Cadoff, Kurt Komarek, Edward Miller

THE lead-telluride phase diagram as compiled by ansen' has one intermetallic compound, PbTe, with solid-solubility limits extending from 22 to 45 wt pct Te (31.4 to 57.1 at. pct). Pelzel2 redetermined the solubility limits on the lead-rich side of the compound by measuring the relative areas of the two phases in samples annealed in the liquid + compound region, and obtained data that agreed with that of Hansen. Recent studies of the semiconducting properties of PbTe3 however, have indicated that addition of either lead or tellurium to PbTe does not produce samples having carrier concentrations greater than about 10 19 cm-3. Assuming that each impurity atom results in one ionized charge carrier, this carrier concentration corresponds to a solubility range of less than 0.04 at. pct. Fritts and Karrar4 have also observed two phases in samples containing from 0.15 to 3.0 pct excess Pb. To resolve the discrepancy between these data, the solid solubility limits of the compound PbTe were reinvestigated, using several other techniques. Ten 25-g samples with compositions of 1/2, 1, 3, 5, and 10 wt pct excess Pb and Te and two 100-g samples of 15 and 65 wt pct Te were prepared, sealed in evacuated quartz capsules, and melted at 950oC. The 1 pct excess Pb and Te and the 15 and 65 wt pct Te alloys were homogenized for 96 hr at 450°C; the remaining specimens were annealed 50°C below the solidus temperature reported in Hansen. The specimens were polished and etched with dilute HNO,. All the samples were two phase, the second phase appearing at grain boundaries or as spheroidized inclusions in the grains. In the case of the tellurium rich specimens, the second phase could be identified as a eutectic. Debye-Scherrer powder diffraction patterns of the i, 1, 3, 5, and 10 pct excess samples were obtained using CuKa filtered radiation. The films were indexed as the B1 or NaCl structure. The calculated lattice parameter of PbTe was the same for all the specimens, with an average of a0 = 6.460 ± 0.0005A. Lines due to excess lead or tellurium were very faint but could be clearly seen in all the films. The relative areas of the two phases in the 15 and 65 wt pct Te samples were corrected for the differences in density of Pb, Te, and PbTe, and taken as proportional to the relative volumes of the two phases. The corrected relative volumes agreed with a phase diagram having negligible solubility of both lead and tellurium in lead tellurium. The density of the two specimens was obtained to give a third independent determination of the phase limits. The specimens were broken into small pieces to eliminate any internal porosity, and adherent air bubbles were removed by vigorous shaking under water for several hours. The density of lead (11.34 g per cm3) and of tellurium (6.25 g per cm3) was taken from the International Critical Tables and that of stoichiometric PbTe (8.25 g per cm3) calculated from the lattice parameter. For the 15 wt pct Te samples, the density assuming no solubility was calculated to be 9.89 g per cm3; the observed density was 9.86 g per cm8. For the 65 wt pct Te alloy, the density calculated for the case of no solubility was 7.24 g per cm3; the measured density wag 7.22 g per cm3. These results are consistent with those of planimetry and X-ray. SUMMARY Data have been presented which show that the solid solubility of both lead and tellurium in PbTe is

Jan 1, 1961

By N. A. Parlee, A. E. Lord

Measurements of the solubility of lead in liquid iron were made at 1550°, 1600°, 1650°, and 1700°C using two different methods, i.e., 1) liquid iron-liquid lead equilibration and 2) liquid iron-lead vapor equilibration. LEAD was long considered insoluble in liquid iron1. Today steels containing 0.15 to 0.35 pct Pb are used. One laboratory has found a solubility of about 0.5 pet in the 1600°C range. Recently Miller and Elliott2 gave 0.60 pct as the result of one determillation at 1540°C. Because these findings resulted from the

Jan 1, 1961

By J. R. Hornaday, A. E. Morris, N. A. Parlee, D. C. Carmichael

Rates of absorption and effusion of hydrogen in solid iron were measurede by a Sieverts type of apparatus. With clean a iron these rates are diffusion controlled down to 420°C and are represented by the equation D = 6.70 x e-'100' crn2 sec-I Certain surface impurities can affect these rates at all temper-atuves. Thin oxide films lower, the apparent diffusivity of annealed iron markedly. Cold-worked iron (75 pct) annealed at 430°C has practically the same solubility and diffusivity as anealed iron. THE mechanism of absorption and evolution of hydrogen in solid iron alloys is not fully understood despite the large number of investigations on the subject. While there appear to be many instances of simple solid-state diffusion control of rate, there are many cases where investigators have either concluded that surface reactions are rate controlling or that some "nondiffusible" hydrogen resides in discontinuities. The purposes of this research were 1) to develop a sound method for studying this absorption and evolution behavior, 2) to examine it in pure annealed iron, and 3) to determine the effects of important variables, such as cold work, surface condition, and composition. This paper relates the progress toward these objectives. Much of the present knowledge of the movement of hydrogen through iron alloys comes from permeability studies which involve the measurement of the rate of passage (under steady state conditions) through membranes of the order of 1 mm in thickness. This method is open to question on various grounds. If surface reactions are involved, two different surfaces operating under two different conditions must be considered. The presence of defects in the membrane even of microscopic dimensions may lead to erroneous results. A few people have studied evolution of hydrogen into vacuum, under carefully controlled (unsteady state) conditions, and some of the best diffusivity data come from these sources. Most of these methods measure rates of evolution only and thus do not make a rigorous test for reversibility of behavior. It appeared that an "unsteady state" method that would permit the measurement of both rates of evolution and absorption under controlled temperature, pressure, and other conditions would offer several advantages. Accordingly the modified Sieverts apparatus described below was designed and built. APPARATUS This apparatus is shown in Fig. 1. The sample bulb is detailed in Fig. 2. Hydrogen of 99.5 pct purity and argon of 99.99 pct purity were used. The hydrogen was deoxidized and dried by means of a Deoxo unit followed by a "Dri-erite" tower. The argon was only dried. The gas burette was graduated in tenths of a cubic centimeter, and, with the aid of a travelling magnifier, readings could be estimated to the nearest 0.01 cc. The level of mercury in the burette was adjusted by means of a leveling bulb operated by a fine screw adjustment. An electrical system, consisting of two slightly separated platinum electrodes inserted in one leg of the manometer and a small light bulb was used to obtain rapid accurate adjustment of the pressure. The capillary tubing of the Vycor sample bulb was 3 mm bore as was all tubing back to the gas burette. The samples were discs made from vacuum-melted Ferrovac-E iron of greater than

Jan 1, 1961

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By W. R. Kube, W. H. Oppelt

Five low-rank coals, including two lignites, a steam-dried lignite, and two subbituminous coals, were carbonized at 940°F, in a bench-scale carbon-ize~ with a nitrogen and hydrogen atmosphere, or both, using pressures from atmospheric to 1000 psig. Coking characteristics were observed, and yields, composition, and distribution of products from thermal degradation were determined. The influence of pressure on yields from coal carbonization, as well as on modification of coke structure, has long been of interest. One of the first attempts at pressure carbonization was that of Capps and Hulett1 who in 1917 investigated the effects of pressure ranging from 1 to 20 atm on yields at 600° C for bituminous and subbituminous coals. High-pressure carbonization has not been used commercially for coke production. More recently, carbonization at relatively high pressure in the presence of catalysts and hydrogen has been proposed for the production of metallurgical-grade coke from low-rank fuels.' Another approach involves carbonization at high pressure in a hydrogen atmosphere to produce heating gas and a solid residue that is gasified with oxygen and steam to produce the hydrogen required for hydro-genation 3-4 or, alternatively, is burned to raise steam. Recently it has been proposed to carbonize coal under pressure, burn the gas in a gas turbine to produce power, and use the solid residue as fuel in a conventional steam-power plant.5 Our primary interest in pressure carbonization stems from an attempt to determine the influence of pressure on the coking characteristics of lignite to design a high-pressure slagging gasifier using oxygen and steam. At atmospheric pressure, North Dakota lignite is generally considered to be non-coking. However, lignite and subbituminous coals have been reported to show increased agglomeration properties in steam, hydrogen, or carbon-dioxide atmospheres at elevated pressures, although no strong coke was formed at pressures up to 3000 psig.6 If lignite would agglomerate seriously under gasification conditions, proper flow of charge through the gasifier could not be maintained without installing a mechanical stirring device or destroying the caking properties of the coal before gasification. Data on the caking properties of lignite or other gasification fuel, as well as on yields of products under conditions simulating the carbonization process in the pregasification zone, were required in the preliminary design stage of the gasifier. No information was available concerning the influence of pressure and type of atmosphere on North Dakota lignite. To provide this basic data, the U. S. Bureau of Mines investigated the effect of pressure and a hydrogen or nitrogen-rich atmosphere on the yield of products and on coke formation in a bench-scale pressure carbon-izer. SCOPE OF INVESTIGATION Five coals were tested at 940°F in nitrogen and hydrogen atmospheres, at pressures from atmospheric to 1000 psig. Yields and composition of solid, liquid, and gaseous products were determined as a function of the process pressure, and attention was given to the physical appearance of the solid residue. Percentage of carbon converted, sulfur retained in char, and thermal balances were calculated. In this paper, primary consideration is given to carbonization in a nitrogen atmosphere and to data concerning the solid phase. The effect of pressure in hydrogen is presented in detail for only one lignite. More complete information on the response of the other coals in a hydrogen atmosphere will be published in a USBM Report of Investigations. DESCRIPTION OF EQUIPMENT Details of the bench-scale pressure carbonizer are given in Fig. 1. The body of the carbonizer was

Jan 1, 1961

By E. S. Anolick, Joseph Singer

The magnetic after-effect, in the form of time decay of permeability (l/µ), has been used to obtain independent data on the solubility of' carbon in pure iron. The results differ slightly from the solubilities obtained through internal -friction experiments. The mechanism of the time decay being the magnetic analogue of internal friction, it appears necessary to explain the observed discrepancies, and some suggestions are made. THE purpose of this work was to establish the reliability of the time decay of permeability as a measure of dissolved interstitial in the body-centered-cubic lattice, and further, to establish techniques suitable for such measurements with samples of a form convenient for various other measurements. This particular sample form was the "epstein" strip, i.e., 25 cm by 3 cm by 0.035 cms. While the general conclusions are not limited by this geometry, there are two aspects of the samples that may be relevant: a) texture, and b) grain size, which ranged generally from 1 to 10 mm. Effects due to these two possible parameters were thought to be small and were not investigated. Calibrating the time decay technique and the other experimental procedures by measuring the solubility of carbon in pure iron suggested itself because of the accumulation of data on this subject through the related technique of the internal friction'; The essentials of this report have been published in a somewhat condensed form.5 Since then some additional data have been taken. It is the purpose of this paper to add these data and to provide more complete description of the experimental techniques than was possible then. The time decay of permeability is a form of the magnetic after-effect.6,7 Permeability is measured immediately after demagnetization (µº) and also long after (µ8). The time decay, ?(l/µ), is the difference 1/µ8 - 1/µ0 and has been considered to be proportional to the concentration of a dissolved interstitial6,8,9,12 The relaxation time! 7, is characteristic of a particular diffusion, and affects the permeability as follows: where he being the activation energy for diffusion of the interstitial. Reference is made to the works of snoek6 and Neel7 for a complete discussion. A brief exposition of the principal ideas may be in order here, as follows. On the basis of the simplest model, resistance against domain wall motion increases with time after demagnetization due to the diffusion of interstitials to preferred sites created by the magnetostrictive tetragonolization under the strong magnetic field. Thus permeability, measured with a small field after the abrupt removal of the large field, will continuously fall with the process of diffusion of the interstitials, and the total "time decay" (or "time decrease") should be proportional to the amount of interstitial in solid solution. In the present report, use is made only of the total time decay rather than of the nature of the progress of the decay; the only problem involved in this approach is the need for assurance that only one interstitial is contributing to the effect as used. It is felt that the special use made here of the total time decay warrants the conclusions. Other work has been going on elsewhere on the detailed study of the nature of the time decay.8'9 EXPERIMENTAL A) Materials—12-lb ingots were made in a vacuum furnace from high-purity iron and by a series of hot and warm reductions were brought down to 14-mil strip. This was cut into 25-cm epsteins. The pure iron was decarburized at 750 °C by hydrogen. The time decay measurement for the decarburized iron (see below) indicated a satisfactorily low starting level of interstitials. Grain growth to grain sizes of 1 to 10 mm was produced in the pure iron by a 700" anneal in hydrogen after a critical reduction of about 7 pct as suggested by previous trials. No measurement of texture in the pure iron was made. The grain size was taken to be large enough to be beyond any sharply critical size regarding solubility. B) Infusion of Carbon—Since the permeability measurement required about two dozen epsteins, a special method of carbon infusion had to be developed to ensure homogeneity of infused carbon. This was accomplished by setting the samples edgewise in a

Jan 1, 1961

By S. R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

John Dasher (Materials and Processes Engineer, Crucible Steel Co. of America, Pittsburgh, Pa.) The authors are to be congratulated for their excellent work, dramatic results, and persuasive explanation on the neglected subject of the temperature variable in soap flotation. The explanation includes why heat is helpful in conditioning and why heat is helpful in flotation. This is a fine start, but I hope the work will be continued to show which is the major effect. In the work of Noman and Dash er(1) it was found that substantially all the benefit of heat came from the conditioning step, and that results were much better if a thick pulp was conditioned hot and then diluted with unheated (or less heated) water for flotation (or agglomerate tabling) than if the same quantity of heat was used to condition and float at some intermediate temperature. In other words, heat for conditioning gives a Rood return, but additional heat for dilution water is near or beyond the point of diminishing return. Strathmore R. B. Cooke, lwao lawsaki, and Hyung Su0p Choi (Authors' Reply) Mr. Dasher'skind comments on our paper are appreciated. In view of the relative simplicity of empirical investigationsof the temperature variable upon conditioning and flotation, it ispuzzling why the subject is so neglected. Our work, being sub sidiary to the main investigation of the effect of structure of fatty acid collectorsupon iron ore flotation, was quite restricted, but we intend to return to the subject as soon as possible. Mr. Dasher's point, that given a certain number of calories it is better to invest them for conditioning in a thick pulp rather than to spread them out for both conditioning and flotation operations, is well taken and cannot be argued. On the other hand there is no question that high temperature during the flotation of iron ores induces superior frothing characteristics, and, in particular, greatly augments the rate of flotation and markedly decreases the time required for "difficult" particles to float.

Jan 1, 1961

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today's quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By J. A. Hren, C. M. Wayman

RECENT investigators have noted anomalous behavior in the electrical resistivity of vanadium below room temperature. Rostoker and Yamamoto1 in studying the vanadium-oxygen system hypothesized that the body-centered-tetragonal phase existing from 15 to 34 at. pet O at approximately 800°K was really a low-temperature allotrope of vanadium that was stabilized by oxygen. In measuring the electrical resistance of cold-swaged vanadium rod over a range of temperatures, a small discontinuity was observed at approximately 240°K, supporting their notion of allotropy. However, the magnitude of the observed discontinuity was extremely small. Loomis and Carlson2 in studying the ductile-brittle transition in vanadium also made resistance measurements and reported a discontinuity near 200°K. More recently, White and Woods3 showed that the electrical resistivity from room temperature to approximately 100 °K was not linear and at variance with the Bloch-Griineisen law. Instead of finding a discontinuity, they observed a deviation from linearity below 200°K. In discussing their results they pointed

Jan 1, 1961

By T. Busch, R. A. Dodd

The solubility of hydrogen in pure iron and pure nickel, and of nitrogen in pure iron, has been determined and agrees well with earlier data. Nitrogen is insoluble in pure nickel and cobalt. The solubility of nitrogen in Fe-Ni alloys also confirms earlier- work. The solubility of hydrogen in Fe-Ni alloys increases non-linearly with increase in nickel content, but the solubility of hydrogen in Ni-Co and Fe-Co alloys reaches a minimum at 75 and 50 at. pet, respectively. The solubility of nitrogen in Fe-Co alloys decreases approximately linearly with increase in. cobalt content. Nitrogen is insoluble in Ni-Co alloys. Determined interaction parameters are in good agreement with predictions of Gokcen and Ohlani. THE solubility of hydrogen and nitrogen in liquid iron and iron alloys has been studied by various investigators.'-l' The method of solubility measuremerit due to Sievertsl is usually preferred when the vapor pressures of the liquid components are sufficiently small, but other techniques such as sampling the equilibrated melt and then analyzing by vacuum fusion have been used quite often. Previously reported data on the solubility of hydrogen and nitrogen in ostensibly pure liquid iron are summarized in Table I; certain of the quoted results were obtained by interpolation of the published data. Agreement between the various investigators is only fair, indicative of the experimental difficulties involved in obtaining gas solubility data. The only report found on the solubility of hydrogen in pure nickel is that of Sieverts.2 The solubility of nitrogen in iron-nickel alloys has received some attention, 10, 11 the results indicating that the solubility decreases with increase in nickel content, becoming zero for pure nickel. There is no published information on the solubility of these gases in either pure cobalt or alloys containing cobalt EXPERIMENTAL PROCEDURE Sieverts' method of solubility measurement was used throughout the investigation. The construction of the melting chamber is somewhat different from A. Optical pyrometer F. Alundum cover B. Vycor chamber G. Alumina crucible C. Furnace coils H. Alundum sand D. Glass water jacket I . Alundum thimble E. Chamber support J . Detachable vycor base sealed with de Khotinsky cement

Jan 1, 1961

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

R. L. Bullock (St. Joseph Lead Co., Bonne Terre, Mo.)— The progressive approach of The International Salt Co. as described by Mr. Ryon is certainly commendable as is his paper. St. Joseph Lead Co. has been shooting AN/FO in 13/8 to 1 1/4-in. holes for several months now (as of October 1960) on a trial basis. The results thus far obtained are excellent, but conclusive evidence at this date is premature. One point that he gave should interest even the most ardent skeptic. That is, they are getting a detonation of the 1 1/4-in. ANDO charges in 2 1/4-in. holes. In light of its low sensitivity and critical diameter, this would appear to be one of the worse conditions that one could expect in which to get proper detonation of AN/FO. It has been shown* that partial confinement sometimes decreases sensitivity of a column of explosive because the air space above the explosive becomes highly compressed and in turn compresses the explosive prior to passage of the detonation front. Apparently, this does not happen in their shooting and the poor explosive coupling caused by the 2 1/4-in. holes yields a minimum of overbreak and is an ideal condition for their back.

Jan 1, 1961

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By Arnlf Muan, Bert Phillips

The quenching technique has been used for- a study of phase velntiorzs within the composition triangle 2CaO.Fe2O3-FeO.Fe2O3 Fe2O3 of the system Ca-Fe-O. Desired total compositions of sanzples were attained by weighing of starting materials in required proportions and keeping them in sealed 80 pct Pt 20 pct Rh tubes during equilibration .runs. The liquidus surface has been delineated. the existence of two ternary compounds has been established, and seven ternary inwariant situations have been determined. ONE unit within the research program on refractory oxides in progress in our laboratories is the study of phase relations in the system Ca-Fe-Si-O. The present paper deals with the ternary system 2CaOFe2O3-FeO.Fe2O3-Fe2O3, which is only a small part of the enormously complex quaternary system. Many of the phases occurring in iron ore sinter products have compositions which can be closely approximated within this ternary system, and a knowledge of stability relations existing among these phases may be expected to be a useful guide for improving sintering operations. Two fundamentally different experimental approach es are commonly used in studies of systems containing iron oxides, both permitting control of the oxidation state of Fe. One method consists in keeping constant the oxygen partial pressure of the gas phase in equilibrium with condensed phases (liquid and crystalline). In the other method, which is the one used in the present investigation, the total composition of condensed phases is kept essentially constant by keeping the samples in a gas-tight container. The details of this experimental procedure will be described in a later section. PREVIOUS WORK Extensive studies of phase relations in the bounding binary system FeOFe2O3-Fe2O3 have been reported by Greig, Posnjak, Merwin, and Sosman,' by Darken and Gurry,2, 3 and recently by Phillips and Muan.4 A diagram summarizing the results of these studies is shown in Fig. 1. Particular attention is

Jan 1, 1961

By John Chipman

THE equilibrium between titanium in liquid iron and titanium oxides has been studied by Hadley and Derge.' They have shown that a minimum occurs in the oxygen content of the metal between 0.1 and 1.0 pct Ti, but its exact level was not fixed. The oxide phase in this minimum range was principally TiO, containing some iron oxide. On the other hand, for concentrations above 5 pct Ti the oxide phase was TiO and the oxygen content of the metal increased rapidly with increasing titanium content. From their observations and the free energy of Ti0 and TiOz reported by Kelley and ah,' it is possible to derive approximate values for the activity coefficients of titanium and oxygen in liquid iron-titanium alloys and the conditions for equilibrium in steel deoxidation. Neglecting possible departures from the stoichio-metric composition, the condition of equilibrium with Ti0 may be expressed as follows: TiO= Ti_ + C) log K = log NTl + log [% O] + log yTi + log fQ Here as a matter of convenience the titanium concentration is expressed in mol fraction while that of oxygen is in weight percent. The activity coefficients are yTi and fo. The value of log fo approaches zero as the concentration of titanium approaches zero, while that of log yTi approaches a limiting value of In Fig. 1 the sum of log NTi + log [% 0] is plotted for mol fractions of titanium between 0.05 and 0.50. The smooth extrapolation gives a value of —4.15 which corresponds to log K — log y:i . We therefore have the equation: According to the data of Kelley and Mah,' the free energy of formation of Ti0 at 1900°K is -82,400 cal. The free energy of solution of half a mol of oxygen in iron, taking 1 pct 0 as the standard state, is -29,300 cal. From these we write: From these equations the activity coefficient of titanium at infinite dilution in iron is found to have a value of 0.011 or log y°. = -1.96. This is only an approximate value but is certainly better than the estimated 0.05 in Basic Open Hearth Steelmaking To obtain approximate values for the activity coefficient at intermediate concentrations, it is as- sumed that log yTi(l is constant and equal to -1.96. This corresponds to a value of E;: = 3 In yTi/aNTi = 9.0 which is not unreasonable We now have the value for the activity of titanium and the percentage of oxygen in equilibrium with TiO. It is therefore a simple matter to calculate the activity coefficient of oxygen which is shown in Fig. 2. The effect of titanium is rather large, being comparable to that of vanadium, but not so large as has been reported for aluminum. The slope of the line at low concentrations corresponds to E: = aln yo/ aNTi=-0.37. At concentrations below 1 pct Ti the deoxidation constant and oxygen content for equilibrium with TiO, can be calculated from the foregoing data and the free energy of formation of TiO,, which according to Kelley and Mah is -144,600 cal at 1900°K. The free energy of solution of oxygen has been given; that of Ti to form a dilute solution with 1 pct Ti as the standard state is RT ln (0.5585 y:i/47.9) = -34,800 cal. From these data we find (for concentrations in wt pct): TiO, = Ti + 2 -0; hFTgO0= + 51,200 cal log if =-5.89 The interaction coefficients, concentrations being expressed as wt pct, are e;: = alogfTi/a[% Ti] = +0.048 and e:' = a logfo,/a[ojTi] = -0.187. The calculation gives the following results which, in view of the impurity of the oxide phase, must be regarded as approximate:

Jan 1, 1961

By A. R. Orban, R. B. Engdahl, J. D. Hummell

The initial phase of a research program on smoke abatement from Bessemer converters is described. In work sponsored by the American Iron and Steel Institute, a 300-lb experimental Bessemer converter was assembled to simulate blowing conditions in a commercial vessel. Measurements of smoke and dust were also made in the field on a 30-ton commercial vessel. During normal blows the dust loading from the laboratory converter averaged 0.51 lb per 1000 lb of exhaust gas. This was similar to the exhaust-gas loading of a commercial vessel. The addition of hydrogen to the blast gas of the laboratory converter caused a decided decrease in smoke density. Smoke was also reduced markedly when methane or ammonia was added instead of hydrogen. The research is continuing on a bench-scale investigation of the mechanism of smoke formation in the converter process. DURING the past 2 years, on behalf of the American Iron and Steel Institute, Battelle has been conducting a research program on the control of emissions from pneumatic steelmaking processes. The objective of the research program is to discover a practical method for reducing to an unobjectionable level the emission of smoke and dust from Bessemer converters. PRELIMINARY INVESTIGATION Although conceivably some new collecting technique may be devised which would be economically practicable for cleaning Bessemer gases, no such system based on presently known principles seems feasible because of the extremely large volume of high-temperature gases involved. Hence, the research is being directed toward prevention of smoke formation at the source. A thorough review was first made of former work to determine the present status of the cleaning of converter gases. No published work was found on work done in the United States on collecting smoke or on preventing its formation in the bottom-blown, acid-Bessemer converter. In Europe, however, a number of investigations have been made on the basic-Bessemer converter. Kosmider, Neuhaus, and Kratzenstein1 conducted tests on a 20-ton converter to obtain characteristic data for dust removal and the utilization of waste heat. They concluded that because of the submicron size of the dust, special equipment would be necessary to clean the exhaust gases. Dehne2 conducted a large number of smoke-abatement experiments at Duisburg-Huckingen in a 36-ton Thomas converter discharging into a stack. A number of wet-scrubbing and dry collectors were tried unsuccessfully. A waste-heat boiler and electrostatic collector with necessary gas precleaners was felt to be the best solution for this particular plant. Meldau and Laufhutte3 determined that the particle size was all below 1 µ in the waste gas of a bottom-blown converter. Sel'kin and zadalya4 describe the use of oxygen-water mixtures injected into a molten bath in refining open-hearth steel. They claim that with use of oxygen-water mixtures the amount of dust formed was reduced between 33.3 and 20 pct of its previous level, and emission of brown smoke almost ceased. Pepperhoff and passov5 attempted unsuccessfully to find some correlation between the optical absorption of the smoke, the flame emission, and the composition of the metal in a Thomas converter in order to determine automatically the metallurgical state in the melt. In a recent U. S. Patent (NO. 2,831,762)' issued to two Austrian inventors, Kemmetmuller and Rinesch, the inventors claim a process for treating the exhaust gases from a converter. By their method the inventors claim that the exhaust gases from the converter are cooled immediately after leaving the converter to a degree that oxidation of the metal vapors and metal particles to form Fe2O3 is inhibited in the presence of surplus oxygen. Gledhill, Carnall, and sargent7 report on cleaning the gases from oxygen lancing of pig iron in the ladle. They claim the Pease-Anthony Venturi scrubber removed 99.5 + pct of the smoke, thereby reducing the concentration to 0.1 to 0.2 grain per cu ft, which resulted in a colorless stack gas after the evaporation of water. Fischer and wahlster8 developed a small basic converter and compared the metallurgical behavior of the blow with that of a large converter. Later work by Kosmider, Neuhaus, and Hardt9 on the use of steam for reduction of smoke from an oxygen-enriched converter confirmed that the cooling effect of steam is detrimental to production. From review of all of the published information on the subject, it was concluded that a practical solution to the smoke-elimination problem had not been found. Accordingly, it was deemed desirable to investigate the feasibility of preventing the initial formation of smoke in the converter.

Jan 1, 1961

By C. S. Finney, John Mitchell

The decline of the beehive coking industry was inevitable, but it had filled the needs and economy of its day. A beehive plant required neither large capital investment to construct nor an elaborate and expensive organization to run. The ovens were built near mines from which large quantities of easily-won coking coal of excellent quality could be taken, and handling and preparation costs were thus at a minimum. The beehive process undoubtedly produced fine metallurgical coke, and low yields were considered to be the price that had to be paid for a superior product. Few could have foreseen that the time would come when lack of satisfactory coking coal would force most of the beehive plants in the Connellsville district, for example, to stay idle; and if there were those like Belden who cried out against the enormous waste which was leading to exhaustion of the country's best coking coals, there were many more to whom conservation was almost the negation of what has since become popularly known as the spirit of free enterprise. As for the recovery of such by-products as tar, light oil, and ammonia compounds, throughout much of the beehive era there was little economic incentive to move away from a tried and trusted carbonization method simply to produce materials for which no great market existed anyway. With the twentieth century came changes that were to bring an end to the predominance of beehive coking. Large new steel-producing corporations were formed whose operations were integrated to include not only the making and marketing of iron or steel but also the mining of coal and ore from their own properties, the quarrying of their own limestone and dolomite, and the production of coke at or near their blast furnaces. As the steel industry expanded so did the geographic center of production move westward. By 1893 it had moved from east-central to western Pennsylvania, and by 1923 was located to the north and center of Ohio. This western movement led, of course, to the utilization of the poorer quality coking coals of Illinois, Indiana and Ohio. These coals could not be carbonized to produce an acceptable metallurgical coke in the beehive oven, but could be so treated in the by-product oven. By World War I the technological and economic limitations of the beehive oven as a coke producer were being widely recognized. After the war the number of beehive ovens in existence dropped steadily to a low of 10,816 in 1938, in which year the industry produced only some 800,000 tons of coke out of a total US production of 32.5 million tons. The demands of the second World War led to the rehabilitation of many ovens which had not been used for years, and in 1941, for the first time since 1929, beehive ovens produced more than 10 pet of the country's total coke output. Production fell off again after 1945, but the war in Korea made it necessary once more to utilize all available carbonizing capacity so that by 1951 there were 20,458 ovens with an annual coke capacity of 13.9 million tons in existence. Since that time the iron and steel industry has expanded and modernized its by-product coking facilities, and by the end of 1958 only 64 pet of the 8682 beehive ovens still left were capable of being operated. Because beehive ovens are cheap and easy to build and can be closed down and started up with no great damage to brickwork or refractory, it is likely that they will always have a place, albeit a minor one, in the coking industry. The future role of the beehive oven would seem to be precisely that predicted forty years ago by R. S. McBride of the US Geological Survey. Writing with considerable prescience, McBride declared: "A by-product coke-oven plant requires an elaborate organization and a large investment per unit of coke produced per day. Operators of such plants cannot afford to close them down and start them up with every minor change in market conditions. It is not altogether a question whether beehive coke or by-product coke can be produced at a lower price at any particular time. Often by-product coke will be produced and sold at less than cost simply in order to maintain an organization and give some measure of financial return upon the large investment, which would otherwise

Jan 1, 1961