Search Documents

By Elton A., Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11 mile bus ride up Railroad Creek to Holden. All freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting.

Jan 1, 1949

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

Jan 1, 1949

By W. G. Pfann

The problem of forming points on wires that were from 0.002 in. to 0.010 in. in diam arose in the recent appearance of silicon and germanium point contact rectifiers as elements in microwave radar.' In these devices a pointed tungsten wire makes a delicate contact with the surface of a semiconductor. Because the quality of such rectifiers is largely determined by the nature of this contact, considerable attention has been given to the formation of the metal point. Reproducibility of contour and freedom from burrs and even microscopic irregularities are considered essential. The operations involved must be simple and rapid enough for mass production. Previously tungsten wircs had been provided with conical points by a grinding method which involved rotating a wire about its axis and causing it to bear at an oblique angle against a spinning abrasive disc. This was later complemented with an electrolytic polishing treatment which removed irregularities from the ground point and also rounded it off at the tip—a desirable feature. Finally, these operations were supplanted by the electrolytic pointing method described here. Mechanism of Point Formation The wires to be pointed are partially immersed in an electrolyte in a vertical position whereupon they are provided with smooth rounded points entirely by electrochemical action. The process is independent of the depths to which the wires penetrate the electrolyte because the points are formed at the surface level. It may be used to point a single wire or many of them simultaneously and is applicable to wires of different diameters within a limited range. Solution of the immersed portion of a tungsten wire is accomplished by making it the positive electrode in an electrolytic cell, as shown in Fig I. While the wire is maintained at constant voltage the current through the cell falls continuously, principally because of the decrease in wetted area which results from solution of the tungsten. This increase in resistance occurs in a reproducible manner and is used as a control in the process. As thc immersed portion of the wire dissolves, it remains cylindrical in shape except for the short section which is wetted by the meniscus. Here the rate of solution is lower and decreases as the top of the meniscus is approached. The result is the formation of a tapered section inside the meniscus. As solution continues, the cylindrical section either dissolves entirely or drops off just before complete solution, leaving only the taper which is now sharply pointed. Further action causes this point to become rounded and then quite blunt, until finally the end of the wire is almost plane. Fig 2 shows the stages in this development. Contour PF is most representative of those used in point contact rectifiers. Thus a variety of point

Jan 1, 1949

THE compiler, or author, of the Probierbücblein is not known, and the date of its first printing is uncertain. It was obviously not written by an assayer who wished to give a coherent description of his craft for the instruction of others; this was left for Biringuccio first to do. It is easy to believe that originally the Probierbücblein was a random collection from various sources of information useful to an assayer, probably gathered by one of the profession for his own use. It must remain a matter of speculation whether this was shown to a printer, who recognized the opportunity to turn an honest penny and made an inept attempt to give the manuscript the appearance of a coherent account by writing a preface and arranging the various items in somewhat logical sequence, or whether the assayer him- self started this job and was prevented from finishing it. That some sections of the book, especially near the be ginning, present an almost continuous story, while others are chaotic in their arrangement; that several paragraphs are printed more than once in different places; that there are paragraph headings, for which the text was never written, or lost, followed by irrelevant information-all this seems evidence of a job unfinished and points to a publisher's offering for the public's quick money. The demand must have been brisk, for metal working was a profitable profession, and the jeweler who was working with metals but did not care to become completely trained in assay methods would jump at the chance of acquiring easy knowledge. Even the great Agricola has whole sections obviously plagiarized from the Probierbücblein. Neither Biringuccio nor Ercker shows any direct influence, though they and all subsequent metallurgists will in some degree be affected by

Jan 1, 1949

By Carl H. Unruh, D. L. Katz

Experimental data are presented for hydrate formation conditions for gas mixtures of carbon dioxide and methane. Equilibrium constants for carbon dioxide, defined as the mole fraction of carbon dioxide in the gas phase (dry basis) divided by the mole fraction of carhon dioxitle in the hydrate (dry basis)... were calculated usine the equilibrium constants for methane developed in an earlier paper. INTRODUCTION A series of papers have been written on gas hydrates, giving temperatures and pressures at which hydrates would form.2. 3, 4. 5, 6. 9. 12, 13, 15 Vapor-solid equilibrium constants have been developed for methane, ethane, propane and iso-butane' by which it is possible to compute for a specific gas mixture the temperature and pressure at which hydrates will form. Carbon dioxide is present in many natural gases in concentrations usually from 0.1 to 2.0 per cent. It also forms a gas hydrate with water and presumably enters the solid solution when present with a natural gas which is forming a hydrate. The equilibrium constant giving the ratio of the concentration of carbon dioxide in the gas phase to the concentration in the solid phase is required for including the effect of the carbon dioxide when computing the conditions for hydrate formation. Direct determination of the concentration of carbon dioxide in solid hydrate requires a difficult separation to be made. Therefore, this research resorted to the measurement of the temperature and pressure at which specific mixtures of methane and carbon diox- ide would form hydrates. From the equilibrium constants previously mentioned for methane, it is possible to compute the equilibrium constant for carbon dioxide, without measurement of the composition of the solid phase. Fig. 1 shows the conditions at which methane and carbon dioxide form hydrates. The methane curve FG extents to some high pressure while the carbon dioxide curve AB intersects the vapor-liquid water-liquid carbon dioxide

Jan 1, 1949

By W. L. Fink, L. A. Willey

During the war there was introduced a new higher strength aircraft alloy designated 75S.1,2,3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75.5 alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75s alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. Procedure Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75s "as rolled" sheet (0.064 in. thick). The composition4 was as follows: Weight Percentage Cu Mn Mg Zn Cr A1 with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16-in. id by %-in. od by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064-in. thickness over the junction and adjacent lead wires for a distance of I 1/2 in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3-in. by 9-in. by 0.064-in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75s extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of 3i-in., 2-in., 3-in, and 4-in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 1/2 in. Thcrmocouple~ were peened into the bottoms Of .1/8-in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1949

By David Turnbull

In most reactions involving solids the transformation kinetics may be represented by the combination of two processes —those of nucleation and of growth. For example, Mehl and his coiq-orker in their studies on the transformation of austenite to pearlite in steels have been able to describe the kinetics in terms of the rates of nucleation and of growth. By micrographic examination of their specimens they determined the nucleation rate (rate of appearance of pearlite colonies) as a function of time, of percent transformation, and of temperature. They observed that after an incubation period in which no nuclei are observed, the number of nuclei appearing per unit time per unit of untransformed grain boundary area, increases at an increasng rate with time. When recrystallization rates have been interpreted in terms of rates of nucleation and growth and the rate of nucleation determined, an incubation period followed by an increasing rate of nucleation has also been reported. Among the studies in which this phenomenon has been observed are those of Kornfeld and coworkers3 on cold-drawn aluminum wire, of Anderson and Mehl4 n the recrystallization of aluminum sheet, and of Stanlcy and Meh15 on the recrystallization of silicon ferrite sheet. The existence of an incubation period during which no nuclei are observed does not appear to have been reconciled with the generally accepted Volmer-Becker theory of nucleation in condensed systems. This theory ostensibly requires the rate of appearance of nuclei to be independent of time. Volmer-Becker Theory In order to form a stable nuclcus of a new phase B in a mother phase A, the molecules or atoms of the mother phase must surmount a free energy barrier whose height is determined by the volume free energy change accompanying the transformation and the energy of the surface separating the two phases. The free energy difference between nuclei of various sizes and the molecules or atoms of the mother phase is plotted schematically in Fig I as a function of the radius of the nucleus r. This free energy difference is plotted for two values of the change of free energy per atom, (Jb — ja) accompanying the transformation when the volumes of the two phases are infinite. One of these values of (Jb—Ja) corresponds to a temperature above the temperature To at which the phascs A and B are in equilibrium, and the other to a temperature below To. In order for a nucleus of phase B to be stable at a temperature T² < TO, its radius must be equal to or greater than the critical value r* for which the free energy of formatioil of the nucleus is a maximum, the of phase B having radii equal to or less than r* will be called embryos hfehl and Jetter," in discussing the kinetics of nucleation in solid systems, suppose that embryos of critical size are formed

Jan 1, 1949

By Arch J. Alexander

Coal is produced, in commercial quantities, in thirty-five of the fifty-five counties of West Virginia. Oil and gas are produced, commercially, in forty-two counties. So, you may readily see that coal, oil and gas arc closely related as to production areas. Many of the West Virginia coal mines are studded with oil and gas wells, as drilling has been done in thirty-two of the coal bearing counties. When the drilling of oil and gas wells was placed under the regulatory control of the Department of Mines on June I, 1929, it was estimated, by the State Geological Survey, that 64,000 wells had been drilled in West Virginia and that 34,000 wells were then being operated as oil and gas producers. No records of many of these remaining 30,000 abandoned wells exist and some of them remain a standing menace to safety as our coal extraction continues. Of a total of 13,100 new wells drilled since June 1929, approximately 5200 have been drilled through coal measures. Approximately 7000 wells, which were drilled through coal measures, have been abandoned in the same period of time. Many of these wells were drilled prior to the enactment of the oil and gas laws. Prior to the enactment of the Oil and Gas Law, which established the Oil and Gas Division of thc Department of Mines in 1929, there had been several mine ex-plosions attributable to cutting into un- charted wells and the improper plugging of other wells. The most serious explosion was that of Mines No. 47 and No. 49 of the Consolidation Coal Co. in Marion Co., when one of the so-called plugged wells leaked or seeped through some 80 ft of strata to the coal bed elevation, filling the mine with gas, the gas being ignited, killing a good many men and wrecking two coal mines. Legislation, to combat well hazards to coal mines, was slow in coming. In 1928, R. M. Lambie, then Chief of the Dept. of Mines, got sufficient support from coal, oil and gas interests to get the legislature to pass our present oil and gas laws. These statutes not only protected the coal industry but went a long way toward conserving the oil and gas resources of our state. Before drilling for oil or gas on any tract of land, known to be underlaid with one or more workable seams of coal, the well operator is required to submit a map of the area showing the location of the proposed well, and to send a copy to the Dept. of Mines and a copy to the coal operator. If no objections to the location of the proposed well are made by the coal operator within ten days, a drilling permit and a number for the well are then issued and work may proceed. If, however, the location of the proposed well is objected to by the coal operator, on the grounds that the location of the well will interfere with present mine operations, projected workings, or otherwise cause a dangerous condition, the operator may file a written objection with the Dept. of Mines.

Jan 1, 1949

By George A. Connell

BORAX, a sodium borate and the principal sodium salt of boric acid, has been surrounded with romance and with a certain amount of mystery. Its early history is not entirely known but it has been contended that Marco Polo in his travels in the Orient introduced this material to the West during the Middle Ages. Without doubt its first source was from Central or Eastern Asia and perhaps from Tibet. The well-known fluxing properties of borax probably introduced its earliest use that of a soldering flux in the manufacture of jewelry. This use, as well as the remote location of most borate deposits, added greatly to the romance associated with the thought of borax. COMPOSITION The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture. The common element in all borates is boron but this element has never been discovered as such in any deposit, because of its great affinity for oxygen. Incidentally, this makes its manufacture extremely difficult and expensive. Elemental boron undoubtedly has many properties that make it quite valuable but the extreme cost involved in producing it from its oxidized form prevents its general use or manufacture of disodium tetraborate (Na2B4O7.10H2O), and, further, can be considered as the acid salt of monosodium metaborate. However, the term "acid salt" might imply that borax gives an acid reaction in solution, which is not true, since solutions of borax are decidedly alkaline, giving a pH of 9.2. Boric acid, also known as boracic acid, has the chemical formula H3BO3; it occurs in nature as the mineral sassolite. Sassolite has been

Jan 1, 1949

By Morris Muskat

The detailed analogy between flow systems in porous media and the corresponding poten-tiometric model systems is developed under conditions where it may be desirable to take into account variable pay thickness, variable porosity, and permeability, and also the dependence of the fluid density on pressure. It is shown that in such models it is only necessary that the electrolyte thickness be made everywhere proportional to the millidarcy-feet of the formation. In contrast to the iso-vol type model, previously suggested as a basis for the analogy, the porosity does not enter directly in the construction of the model. It is introduced only in translating the electrical voltage gradient measurements into the equivalent fluid travel times. A discussion of this procedure is given. I NTRODUCTION It is now some 50 years since it was pointed out&apos; that on the basis of Darcy&apos;s law Laplace&apos;s equation must govern the steady state flow of homogeneous fluids through porous media. It is 16 years since the obvious implication of this fact, namely, that such steady state homogeneous flow systems in porous media could be simulated by electrical analogies, was first applied2 to problems of practical interest with respect to oil production. In these initial studies major emphasis was placed on the use of electrolytic models, made of blotting paper, to give a direct and graphic history of the fluid particle motion in regular and infinite well networks. However, it was also noted there that the basic requirement of the model was that it give a potential distribution similar to the pressure distribution in the flow system, and that from the electrical measurement of the potential distribution the fluid particle motion could be graphically or numerically determined. This was demonstrated by application to the five-spot infinite network, for which a conducting metallic sheet was used to establish the equipotential contours. As anticipated, the fluid particle motion computed from these contours agreed well with that given directly by the blotting paper model. For irregular well distributions it was found more convenient to use electrolytic bath analogs rather than metallic sheets. Several investigations,3&apos;4 as applied specifically to cycling well patterns, have been reported with these models, which have become known as "potentiometric models." However, the extremely laborious nature of both the electrical measurements by direct probing and the associated interprctive computations retarded the widespread use of these procedures. The electrical measurements can be accelerated by using a four-probe electrodc,5,6 which provides a means for simultaneously determining the streamline paths along which the fluid particles must move and the voltage gradients along these paths which are proportional to the fluid velocitics. With the increasing frequency of discovery of condensate pools, as drilling depths are becoming greater, the applicability of the potentiometric model to production problems, and especially to the study of well patterns for cycling, has been given a fresh impetus. Although the formal theory for determining the motion of fluid particles in porous

Jan 1, 1949

By B. D. Cullity

This investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy—the thermoelectric efficiency—has been discussed by Telkesl in a recent review of the subject. She gives the thermoelectric efficiency as: W o Efficiency = -Wo ______________i____________ TR-TC+ O2TR-Tc) where W, = power output in external load (watts) Wi = rate of heat input to hot junction (watts) TE,T, = temperature of hot and cold junctions (oA) K1,Kz = thermal conductivity of the two thermocouple materials (watts/cm°C) p,,pz = electrical resistivity of the two thermocouple materials (ohm cm) 9 = thermoelectric power (volts0/C) For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of pfoperties. Bismuth-selenium Alloys work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson who gives the diagram reproduced in There are two intermediate phases in this system, BiSe and Bi²Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedra1 crystal

Jan 1, 1949

By H. H. Reamer, B. H. Sage, J. S. Billheimer

Jan 1, 1949

By B. M. Loring, W. H. Baer, G. M. Carlton

It is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen. Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). The material for this investigation consisted of extruded rods 1 1/4 to 136 in. in diam. The chemical compositions were as follows: The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0.015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to 3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements. AT

Jan 1, 1949

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By Norman Weiss

Most papers on xanthate have dealt with principles rather than practice. On the assumption that many millmen are interested in knowing where and in what manner the xanthates are being used in mills other than their own, this paper will summarize the results of a recent survey of North American plants. A brief background story and a description of the xanthates will be followed with the results of that survey; then a few observations will be made on storage, feeding, and ore testing. The first xanthate was made in 1822 by Zeise of the University of Copenhagen. With commendable scientific detachment (or perhaps a bad cold) Zeise ignored a more pervading quality of the substance and named it for its color, after the Greek word "xanthos," meaning yellow. During the first 80 years of its recorded existence xanthate found use only in small quantity as an insecticide; after the turn of the century there was some further demand for it in the vulcanization of rubber. It was not until 1922, by coincidence the centennial of Zeise&apos;s discovery, that C. H. Keller of San Francisco, seeking sul-phidizing agents, recalled xanthate in connection with his experience years earlier when he had seen this material used in Europe to combat grape phylloxera. His successful tests with the new flotation reagent culminated in the basic xanthate patent (U. S. 1,554,216) in 1925. In the minds of many metallurgists the introduction of xanthate as a flotation reagent is identified with the beginnings of alkaline circuits, the first use of chemical collectors, and the beginning of selective flotation. Actually, these preceded xanthate by a number of years. The alkaline circuit in lead-zinc flotation was introduced by Lyster as early as 1912. In 1922 Sheridan and Griswold made their momentous discovery (Timber Butte) that alkali cyanides and zinc sulphate effectively inhibited the flotation of pyrite and sphalerite in pulps made alkaline with sodium carbonate or bicarbonate. The use of lime to retard pyrite in copper flotation began within two years after Ralston directed attention to its possibilities in 1917. These were the beginnings of modern selective flotation, which was practiced successfully on copper-iron ores at Nacozari in 1922, and at Inspiration, Cananea, and others only shortly afterward. In the lead-zinc mills, selective flotation was of even greater economic importance at that time. The Sunnyside plant of U. S. Smelting, Refining, and Mining Co. used the process earlier than 1920, and Consolidated, Timber Butte, and others soon followed. As a chemical collector xanthate was relatively a latecomer, for the Corliss patent of 1917 covered the first of these, alpha-naphthylamine, and the Perkins patent of 1919 the second, thiocarbanilid. Both of these were in extensive use before Keller&apos;s xanthate made its commercial debut in 1923. There is general agreement, nonetheless, that the introduction of xanthate was

Jan 1, 1949

By A. B. Parsons

PUBLICATION of this little volume is a luxury that the Institute itself could scarcely afford. In truth, no engineer nor geologist, no assayer nor metallurgist would be likely to enhance his knowledge, improve his technique, or cut his own operating costs by reading this excellent translation of two booklets first published circa A.D. 1520. It is doubtful if the present enterprise would, in a practical or tangible way, "promote the arts and sciences connected with the economic production of the useful minerals and metals." And such, is the prescribed purpose for which the funds of the Institute should be spent. Fortunately for the Institute, the Seeley W. Mudd Memorial Fund is not so circumscribed; and the Fund Committee enjoys, greater liberty of action. The sponsorship by the Mudd Fund in 1942 of the publication of The Pirotechnia of Vannoccio Biringuccio, as translated by Dr. Smith and Mrs. Gnudi, was an innovation-indeed something of an experiment. Not only was the content of the volume significant mainly for its "cultural" and "scholarly" attributes; -but the format, an outstanding example of the fascinating art of bookmaking, bore no resemblance to the ordinary technical book. The Committee, frankly, was surprised at the enthusiastic reception accorded the volume. When a second edition was required, the Committee became convinced that the publication of material of this type, particularly if printed and bound in attractive form, was an appropriate avenue for utilizing a moderate proportion of the monies available from the Fund. The Bergbüchlein and the Probierbüchlein antedate by some years the first publication of De la Pirotechnia and of De re Metallica; but Georgius Agricola, the author of the latter work, made good use of the material in the earlier volumes. As pointed out in the Introduction, both

Jan 1, 1949

By R. C. Thompson

The lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 450-ton operation. General Description The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1949

By J. S. Bryner

In the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light rnicroscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silicalJ replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/8 in. diam zoo-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. Description OF Method The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper I X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1949

By Robert W. Metcalf

THE name "tripoli" is used to designate a number of more or less similar types of silica of sedimentary origin. Usually they are spoken of as "soft" silicas, and are light, very fine grained, porous, and friable. Structure is microcrystalline or cryptocrystalline. The deposits are the residual product of weathering and occur in massive form, either blocky or in friable masses. Tripoli is the end product of the weathering of siliceous Limestones, cherty limestones, or cherts. Weathering removes the calcium carbon- ate, leaving a finely divided siliceous residue to which the name "tripoli" has been applied. Authorities differ as to whether the chert accumulates first and is converted into tripoli or the tripoli is derived by direct decay from various forms of silica during initial weathering of the Limestone. It has also been asserted that tripolis were formed in situ in essentially their present condition as a flocculent, colloidal silica, but it is now believed by most geologists that varying degrees of pressure, combined with one or more methods of origin, have influenced the characteristics of the deposits. Considerable confusion has existed as to what constitutes tripoli. Owing to the similarity of names, tripolite, a type of diatomaceous earth found originally in Tripoli in northern Africa, has been erroneously called tripoli. Tripoli, however, contains no diatoms, the distinguishing characteristic of diatomaceous earth. The material mined in the Missouri-Oklahoma area has been considered by the trade to be the type material, and many feel that the term "tripoli" should more properly be restricted to the product of this region. Although also designated as soft silica, it would be less misleading, perhaps, if the siliceous material mined in southern Illinois were called amorphous silica. Both the Missouri-Oklahoma and Illinois materials are very high in silica. Different in composition, as it is very much lower in silica content than tripoli or amorphous silica, yet included under the classification of tripoli in Bureau of Mines statistical data, is the small but important output of rottenstone in Lycoming County, Pennsylvania. The principal justification for grouping these three types of silica is similarity of use.

Jan 1, 1949