Search Documents

By Cyril Stanley Smith

Jan 1, 1949

Jan 1, 1949

By Louis A. Panek

The purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fen tress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal held exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The miaximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repiesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: Safe R =(1/4)4p2n2r/g=p2n2r/g [I] in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sec2.

Jan 1, 1949

By G. Richards Gwinn

THE mineral graphite has been known for hundreds of years and was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century and its commercial development did not become extensive until near the close of the nineteenth century. The common names for this mineral are graphite, plumbago, and black lead; others less frequently used are potelot, crayon noir, carbo mineralis, and kish. Graphite was named by Johann Gottlieb Werner in 1789 from the Greek word graphein, to write, and this name was applied primarily to the large crystalline, flake variety. Plumbago is a trade term used primarily for massive graphite as found in Ceylon. Black lead is also a trade term and, like plumbago, is based upon the idea that prevailed throughout the Middle Ages that graphite was a form of lead, or at least contained that metal. Graphite is a soft, black, unctuous form of carbon that crystallizes in the hexagonal system with rhombohedra1 symmetry. It occurs occasionally in six-sided tabular crystals but usually is found in foliated masses, minute disseminated scales, or earthy lumps. It has perfect basal cleavage, is gray to black, has a metallic luster and a gray streak. The specific gravity is 2.1 and hardness is 1 to 2. It is opaque even in finest particles; extremely resistant to the action of acid or heat; and a good conductor of both heat and electricity. Graphite may be separated into three classes: ( ) natural, (2) manufactured (which is sometime called artificial), and (3) colloidal. Natural graphite is divided into two classes, "crystalline" and "amorphous." Crystalline graphite may occur as flake, lump, chip or dust. Amorphous graphite is a commercial term only, as all graphite is crystalline, but grades in which the individual grains cannot be distinguished are classified by the trade as amorphous. Natural mixtures of crystalline and amorphous occur in all proportions. The term "artificial graphite" is a misnomer; "manufactured graphite" is a better term, because it actually is pure crystalline graphite,

Jan 1, 1949

By F. W. McQuiston

Idarado Mining Company's mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation I2,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. Ores The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper. lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galenn is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (I) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic inter-growth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. Plant Practice Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1949

By T. W. Guy

The increased moisture due to water-spraying for coal dust control is of interest even for mines from which the coal is to be wet-washed before screening, because in many cases wet coal dust materially de- 20-mesh X 0 sizes as pct ROM average ............................... 6.3 pct Range 2.3 to 9.5 pct 20-mesh X 0 sizes as pct 3/8 X 0 sizes average........'...................... 18.9 pct Range 12.7. to 23.9 pct creases the loading efficiency of men and equipment at the faces. It also causes a serious increase in the normal wear and deterioration of all equipment with which it comes in contact. It is important to the consumer if it increases his as-received moisture. No attempt will be made in this paper to cover the entire subject of water-spraying of coal for dust control. It will be confined to discussion and data on (I) percentages of dust in bituminous coals, (2) moisture increases due to spraying for dust control in mines or plants by methods which have proved satisfactory for periods of one to five or more years, and (3) a few suggestions for research. Size and Percentage or Coal Dust The U. S. Bureau of Mines1 classifies as coal dust all bituminous coal passing a 20-mesh sieve (0.0328 in. square opening). The percentage of such dust to be found in ROM coal, of course, varies widely with the characteristics of the seam, and with the methods used in the mining and in the preparation of the coal. ROM screen analyses of 12 U. S. coals selected at random from personal files given in Table I show: A few other screen analyses examined indicating 40 pct or more of 20-mesh X 0 dust in 3/8 in. X 0 sizes were not included because of uncertainty that they were representative. The number of results in Table I is not sufficient to give a reliable estimate of the average, or of the range to be expected, but it indicates that in every case the coal dust is a relatively large percentage of the total ROM coal, and, of course, a progressively larger percentage of resultants as the larger sizes are separated for marketing.

Jan 1, 1949

Jan 1, 1949

Jan 1, 1949

By Robert B. McCormick

THE major use for quartz crystal is in the manufacture of radio oscillator plates and telephone resonator and filter crystals. Quartz crystal is also cut and polished as a semiprecious gem stone, particularly in the colored varieties (amethyst, Brazilian topaz, and others), and often is carved into various objects of art. Prisms, wedges, lenses and other optical parts often are made of quartz crystal, usually for special- purpose instruments. Chips and small clear crystals below 100 grams in weight, called “lascas” by the trade, are the raw material for fused quartz products. HISTORICAL BACKGROUND The Greeks believed quartz to be permanently frozen water and therefore called it krustallos, which, literally translated, means clear ice; but ages before their civilization, prehistoric man had crudely cut and polished crystals for rough charms and ornaments. About 2000 B.C., the Egyptians brought the art of cutting quartz to a high level. While there are earlier examples of crystal art that have great value, working in crystal during that period became a means of artistic and religious expression that has endured through the ages. Art museums and private collections throughout the world contain many priceless pieces. They include findings from the tombs of the earliest Egyptian rulers, as well as magnificent art objects in both clear and colored crystal encrusted with silver, gold, enamel, and precious gems of oriental and European workmanship. Pierre Curie first measured the piezoelectric effect of quartz, in 188 1, by placing a weight on the surface of a quartz crystal and measuring the resulting electrical charge, which he found was proportional to the weight applied. The following year the inverse piezoelectric effect was proved by the Curies. By applying a voltage to a piece of quartz, a measurable physical displacement occurs. The first practical application of this effect was the construction of a bimorph unit to measure voltage by measuring the amount of the displacement of the end of the bimorph. The piezoelectric properties of quartz crystal remained largely a laboratory curiosity until World War I, when a supersonic device for

Jan 1, 1949

By E. A. Gulbransen, W. S. Wysong, K. Andrew

The reaction of carbon in solid solution in a metal with the surface oxide fim on many metals may be inferred from thermo-dynamic calculations for high vacua and high temperature conditions. Holm has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. considerable work has been described in the literature on the de-carburization reaction. Several general references may been 2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides on strips of various types Of chrome-nickel alloys. Some of the early experiments On the behavior Of '3 pct chrome-iron in vacua of the order of 5 X lo' mm and at a temperature Of 600°C have been reported.5 These experi-merits showed a 'low reaction with the residual Oxygen Or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600' C pure enough to reduce Crz03 formed On the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome- iron and Nichrome V has been investigated in the thin film range by Gulbransenr Phelps and Hickman,' and shown to be "203. It Was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pet nicke1 and 20 pet chromium was heated to 850°C in a high vacuum, the specimen lost weight. The rate Of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. Type Reactions Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type, They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: 1. Metal . (gas) F? metal + gas — degassing of the metal 2. zM(s) + y }i Oi(g) M MIOu(s) -oxidation

Jan 1, 1949

Jan 1, 1949

By Edward C. J. Urban

The nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than 10 years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini- tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. Development of Rock DriI,I.s Thc earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its Piston-Type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1949

By Wayne E. Glenn, R. W. French, Lincoln F. Elkins

The Lance Creek Sundance reservoir provides a case history of ro years performance of a reservoir in which unit operation has permitted effective utilization of gravity drainage augmented by primary pressure control with injection of gas into top structural wells. Detailed performance of the reservoir is presented by means of maps of Well status, reservoir pressure, individual well recovery, etc., and by pool-performance charts. Analysis of reservoir performance indicates only minor water encroachment, so that gravity, injected gas, and expansion of gas are the main oil-expulsive agents. A simplified theory of regional drainage of oil from upstructure location to downstructure location due to gravity is presented and checked by means of comparison of "reservoir" permeability and "well" permeability from the pool performance. Good order of magnitude agreement was obtained. Individual well performance and overall reservoir performance indicate possibility that maintenance of pressure makes ineffective those parts of the reservoir in which permeability is too low to permit effective drainage of oil by action of gravity. Oil from these parts can be recovered only when pressure is reduced locally by selective withdrawal or when overall reservoir pressure is finally reduced.

Jan 1, 1949

By S. S. Clarke

Late in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of Jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of Jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1949

By R. E. Zimmerman

The separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pet successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the —48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of —48-mesh slurries. These large scale operations have been recently described by D. H. Davis.' C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investiga-tional work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investiga-tional work as well as the results of experiments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. Methods of Conducting Laboratory Tests The bulk of the research work was conducted in the laboratory of the Champion No. I Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location for the investigational work. Four types of laboratory flotation ma-

Jan 1, 1949

By Carl Belser

This paper summarizes the data on the oil-shale deposits of western Colorado, Utah and Wyoming. It is based on published reports by the U. S. Geological Survey, on the results of core drilling and sampling by the Bureau of Mines, on the drill cuttings from the Genera1 Petroleum well, on a recent unpublished report by the Geological Survey on the geology of Naval Oil-Shale Reserves No. I and No' 21 and from information supplied by geologists of private companies who have investigated the Green River formation. The paper also contains a revised estimate of the grade and tonnage of minable thicknesses of oil shale of western Colorado. Introduction The oil shales of the Green River formation of Colorado, Utah and Wyoming comprise an important natural resource for the production of synthetic liquid fuels. The oil shale in western Colorado generally is more amenable to exploitation, apparently richer, and probably more persistent than in Utah or Wyoming. Work is now being done by the Bureau of Mines near Rifle, Cola. to ascertain the best procedures for mining the oil shale, producing shale oil from the oil shale, and converting the oil into more salable products. As a part of this program, holes were drilled and cores were taken of the oil shale on Naval Oil-Shale Reserve No. I. In addi- tion, drill cuttings were obtained from a well drilled through the Green River formation by the General Petroleum Co. about 18 miles northerly of the Naval Oil-Shale Reserve. Geology During middle Eocene time a broad, shallow body of water, now called Uinta Lake, covered northwestern Colorado and east-central Utah; a similar lake, known as Gosiute Lake, was in southwestern Wyoming Each of these contemporary lakes was bounded by high hills; the drainage was to the south. The Green River formation was laid down as sediments in the bottoms of these lakes. It is 3000 ft thick and has been divided into the following four members:

Jan 1, 1949

Jan 1, 1949

By J. E. Burke

Recent investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers 1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen. Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: D = Ktm [,] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Wa1ker4 finds that, in alpha brass) the rate of growth falls off more rapidly than indicated by Eq i after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker's data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: ] where h and tz are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck3 The results obtained by Beck Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and HuV ater demonstrated expcrimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,io Making implicit use of this assumption, several authors14,16 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parkerg have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary7 are on the average more surromded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1949

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By Orville R. Lyons, A. C. Richardson

During the past few years there has been a growing demand by coal operators for detailed information about the performance characteristics of the various dryers now being manufactured, preferably in such a form that the information could be used to determine the type of dryer best suited to a particular drying problem. A few operators have been desirous of going even further, because they are of the opinion that present-day dryers are not properly designed and that fundamental studies of dryer design should be undertaken. This growing demand for a method of dryer evaluation and the indicated need for fundamental research resulted in the sponsorship by Bituminous Coal Research, Inc. of a project at Battelle Memorial Institute to investigate the thermal drying of coal. In investigating this problem, the most feasible method of attack appeared to be a survey of active operations to determine the present status of the thermal drying of coal. Data were obtained, usually by actual plant tests with the cooperation of the various preparation engineers and their staffs, for 9 screen-type dryers, 8 rotary-type dryers, 3 continuous-pallet-type dryers, 2 flash-type dryers, I tray-type dryer, and I cascade-type dryer. The testing program provided: (I) data for 24 coal-drying operations, (2) information about the inherent characteristics of the coals dried, (3) information about the previous treatment that the coal had received, and (4) information about operating costs. The data obtained through the dryer survey and relationships determined from the data make it evident that all of the types of dryers included in the survey can be operated with the same degree of effectiveness if each type of dryer is used to dry the sizes of coal for which it is best suited. It should be noted that it is usually undesirable and often impossible to dry different sizes of coal in one type of dryer. By use of the data in the report, any prospective dryer user, having determined the surface moisture percentage and screen-size analysis of the coal to be dried, the tons of water to be removed per hour, and the final surface moisture percentage desired, should be able to determine with a fair degree of accuracy: (I) the difficulty of the drying problem, (2) the approximate cost of drying, (3) the required dryer inlet gas temperature and volume and exhaust gas temperature and volume, (4) the type of dryer to use, and (5) the size of dryer required. The method of testing the dryers and determining the difficulty of drying can be used by operators already having dryers to check the performance of their particular dryer and determine whether they are operating effectively. Considerably more information was obtained from the survey of thermal drying than was anticipated when the survey was first considered. However, a great deal of work still remains to be done in the field

Jan 1, 1949