Search Documents

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By E. E. Wark, I. W. Wark, J. Rogers. K. L. Sutherland

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By Nathaniel Arbiter, A. F. Taggart

The chemical reaction occurring in collection of nonmetallic minerals with amine-type collectors was early postulated by students of flotation phenomena to be metathesis between the mineral and the collector, involving exchange between the amine-bearing (aminium) ion and the cation of the mineral, and formation at the mineral surface of an oriented film of the amine salt of the mineral anion. Qualitative evidence of exchange has been obtained on several occasions at Columbia. Thus 1000 C.C. of a solution containing 495 mg of laurylamine hydrochloride was shaken 17 min. with 100 grams of barite and ground in a porcelain mill to pass a 200-mesh screen; the mixture was then set aside for 48 hr. Filtrate therefrom analyzed 476 mg. per liter of laurylamine hydrochloride. There was no substantial loss of chloride ion (78.4 mg. per liter in the original; 74 in the filtrate). No successful analyses were concluded for barium ion. Earlier, confessedly rough work with scheelite indicated a solution gain in Ca++ equivalent to about one-half the aminium ion lost. Real quantitative roof of the exchange, in the form of an established stoichiometric balance, is unknown to the authors. The data of the present paper, however, obtained from experiments designed on the basis of the exchange hypothesis, constitute strong evidence of its truth, and at the same time point the way to economic utilization of the expensive nitrogen-bearing collectors in concentration of the low-priced nonmetallic minerals. The basic postulate underlying the experiments performed was that, if the collecting reaction is of the type R+ + Y- + MX = RX + M+ + Y- where R = aminium ion, Y = the anion of the amine salt, and M and X are, respectively, the cation and anion of the mineral, the reaction should obey qualitatively the implications of the mass-action and solubility-product laws. This is to say that coating and collection should be aided by the addition to the solution of either ion (R+ or X-) of the collector-coating compound, and hindered by the addition of either of the ions M+ or y-. Experimental work comprised determination of (,) the relative solubilities of the laurylammonium salts of a variety of nonmetallic-mineral anions; and (21 the contact angles' of various minerals in solutions containing different concentrations of the postulated controlling ions. Semiquantitative flotation tests were run With barite as checks on the diagnostic character of the contact angles. The amine

Jan 1, 1947

By Edward Pesout

The McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.' Early Pulverizing Plant Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a her product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. o-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1947

By Julius Albert Krug

IN the field of mineral resources, today's problems and those we can reasonably expect in the future are so vast that nothing less than world-wide thinking and world-wide planning will suffice. I can imagine nothing more useful for the Institute to do in celebration of its seventy-fifth anniversary than to hold this conference on world mineral resources. Mineral resources are the basis of any nation's industrial production. Without expanding industrial production, the high standard of living found in the United States could not exist. Without such a standard of living it would be most unlikely that we should have a high level of culture. The hope of the world, as I see it, depends very largely on a general rise in living standards everywhere, and in the general increase of the levels of culture including a sympathetic understanding of the problems of other nations. For this reason, the proper use of the world's remaining mineral resources must be taken into account in any plans to safeguard the peace of the world. Being as exasperatingly human as human beings always seem to be,. we usually wait until almost too late to begin our plans to stave off an impending disaster. We do this as individuals, as components of particular States or Governments, and as citizens of the world. We waited, if not too late, certainly a very long time in getting started on the job of world-wide con-

Jan 1, 1947

By W. R. Seyfried

THE problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. THE PROCESS AS PLANNED In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the Company, first drafted a process in July of that year-five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or low-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F), (b) The roasted ore would then be leached with hot aqueous ammonium bisulphate to form a slurry. In this way the

Jan 1, 1947

Jan 1, 1947

By J. F. Myers, S. D. Michaelson, F. C. Bond

THIS work was undertaken with the object of collecting plant data on rod milling, making laboratory tests on representative samples of the various ores, and arriving at a basis for comparing the relative efficiencies of different mills operating on widely different materials and under varying conditions. These efficiencies consider only power consumption and do not include the other elements of operating costs. The over-all economic efficiency may be quite different from the consumption efficiencies with which this paper is concerned. It is hoped that these collected data will be of value in indicating the most favorable conditions of rod-mill operation. Operating-plant data on 14 different installations from 11 plants throughout the United States and Canada were collected, and laboratory tests were made on samples of these ores. The plant rod mills were all operated wet, and either in open circuit or with circulating loads so small as to be negligible. Data were obtained on one roll-crushing operation at the Utah Copper Co., for comparison. The rolls were operated wet in closed circuit with 10-mesh vibrating screens, and with a high circulating load averaging about 600 pct. This particular roll operation can be considered as a model of efficiency. The collected plant data are necessarily incomplete in some instances. Each ore was assigned a code number, and the name and location corresponding to the code number are listed in Table I when permitted. [ ] The power data in every instance refer to motor input. Net power was reported by the operator for samples I-39 and I-45, and this was increased by 20 pct to compensate for motor losses and power factor. The plant rod-mill data are listed in Tables 2 and 3. In Table 2 the speeds are calculated on the basis of partly worn rod-mill liners 2 in. thick. Where D

Jan 1, 1947

By Fred J. Wright

Originally, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are. now literally the heart of the mining machine. During world war NO. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the Same time will lower costs for the oil by extending its life. Rulk purchases of oil should be limited to small sealed containers provided with a Proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives1 will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1947

By Sam F. Carter

FOR some time melters and metallurgists have recognized the fact that steels may be made to identical compositions as ordinarily analyzed, but with considerable variations in physical properties. Good melting practice signifies a combination of furnace operations that will produce steel with consistently good physical properties after proper consideration of cost, production efficiency, and chemical control. In acid practice, these operations may be classified fundamentally as: (I) the oxidizing boil, (2) recarburization and deoxidation, (3) slag adjustment, and (4) final deoxidation. These operations affect the properties of the steel through variations in the minute quantities of several microscopic, submicroscopic, and dissolved constituents, which are out of reach of ordinary analyses but are very influential upon the crystallographic slippage and the molecular cohesion of the structure. One of these constituents is the FeO left in solution in the steel. Herty has shown that steels high in dissolved FeO have decreased ductility and impact and increased hardness and electrical resistance. There is also much evidence that FeO in solution affects carbon solubility and diffusion, and consequently abnormality and carburizing behavior.

Jan 1, 1947

By John M. Hancock

IN beginning my remarks, may I make it entirely clear that since January 4, 1947, I have not been a member of the United States Delegation to-the United Nations Atomic Energy Commission I am speaking, therefore, in purely a personal capacity. Because of the interest of the engineering profession with reference to uranium, and because of the title assigned me for this talk, I am going to assume that you know what the United States Plan is for the control of atomic energy. At best, in the limited time, I could only summarize, at the risk of giving undue emphasis to the items mentioned, and at the risk of omitting many important parts of what seems so far to be a complete and well-rounded Plan for meeting the problem. I will aim to comment upon those aspects of the Plan that continue as problems and involve apparent, or obvious, misunderstandings and contrary views The control of atomic energy represents not only a problem but a challenge-both faced by- all the peoples of the world It involves a new approach to the problems of the kinds that arise between nations, problems that have not ever been solved even by international treaties in their efforts to outlaw weapons of war. These efforts range from the Kellogg-Briand treaty to outlaw war, and its obvious failure to prevent World War II, to the interdiction by the Pope of the use of the crossbow in the days of the Crusades. All previous plans have been failures-that makes

Jan 1, 1947

By C. E. Sims

THE carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example,, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath. The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner without reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature. For the carbon-oxygen reaction C + 0 [=] CO this is expressed simply as [ ] where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

The physical and chemical structure of the oxide films formed on metals and alloys is of interest in our understanding of their protective properties. According to Pilling and Bedworth,¹ if the specific volume of the oxide is equal to or greater than that of the metal, a compact or continuous structure results; if the volume of the oxide is less, a cellular or porous structure forms. With the cellular type of coating the surface layer of oxide offers no impedance to oxidation; at a given temperature the rate of oxidation is quite constant. On the other hand, the compact type of coating acts as an effective barrier to oxygen and the rate of oxidation will follow a parabolic law. The recent work of Gulbransen2 and of Leontis and Rhines3 on the oxidation of magnesium indicates that it is not necessary for the volume of the oxide to be greater than that of the metal in order that the oxidation may follow a parabolic rate law. One exception to the rule of Pilling and Bedworth¹ is noted by Scheil;4 namely, tungsten. At 500° and 700°C long-time oxidations indicate a linear rate law with time. However, Dunn's6 0xidation measurements from 700°to 1000°C indicate that a parabolic rate law is followed. The oxide is mainly yellow WO a with a thin layer of the blue oxide. Preliminary results on the oxidation of tungsten6 in the temperature range 400° to 500°C indicate that the oxidation does proceed according to a parabolic rate law. Irrespective of the actual rate law that tungsten may obey, it is of interest to compare the results obtained on the oxidation of tungsten in the thin film region with those found when the metal is scaling. A time-temperature study of the oxides formed on both molybdenum and tungsten may indicate whether there exist any peculiarities in the oxide structures of the thin film region compared with those of the scaling region of oxidation. In a recent paper the authors7 presented an investigation of the structures of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper. The results of these studies are presented in graphical form as existence diagrams of the oxides on a time-temperature scale. The existence diagrams of the oxides occurring on some of the metals are simple and show few chemical transitions, but there are many cases in which the physical state of the oxide surface changes as a function of time and temperature, as evidenced by the appearance or disappearance of orientation effects and sharpness of patterns. In general an increase in temperature results in an increase in

Jan 1, 1947

By Foster Fraas

INTRODUCTION THAT variations in the humidity of the air and in the moisture content of a mixture of broken solids being separated electrostatically cause trouble is not new.1 Much of the reputation for unreliability commonly ascribed to the electrostatic separation processes is probably due to this one factor alone. Some operators dry thoroughly before separating; and while this is good in many instances, there are others in which it is not the remedy for trouble. Some mixtures behave best in very dry air and with the mixtures fed to the separator while hot to reduce the adsorbed water content. On the other hand, an overdried mixture on coming to equilibrium with more humid air, has been known to take up moisture selectively on one family of particles, as of coal in the presence of slate and clay, and give sharper electrostatic separation. From these observations it is concluded that there is a permissible moisture content for a particle and also for the atmosphere surrounding it, if in equilibrium, at which the particle will have a conductivity or contact potential2-4 that is ideal for electrostatic separation. This permissible moisture content varies between a wide range of limits for the different materials that are separated and with the kind of electrostatic separating process used. Water can be present as a result of adsorption and condensation from the atmosphere, as an accumulation before or during mining, or as a residue from a previous process step. The water may exist as a liquid film or as an adsorbed layer of vapor. If the water exceeds permissible limits it must be removed. Its state determines the method. Drying by evaporation is necessary for adsorbed water, for part of the liquid-film water (that is, up to several percent of the dry weight), and for free water in the internal structure. Large water contents may be removed by drainage or filtration. At just what point mechanical removal should cease and drying by evaporation begin depends upon the method of mechanical removal and its cost. Particles can also be separated according to their differences in dielectric constant when suspended in a liquid of intermediate dielectric constant. Recovery of this liquid presents a similar problem. PERMISSIBLE MOISTURE The adsorbed moisture on the outer surface of minerals can be quickly removed or replaced. Accordingly, in speaking of adsorbed moisture contents, either that of the solid or that of the surrounding air may be considered, the two values being connected by a distribution coefficient which varies with the temperature. However, such a condition does not necessarily exist in processes where an initially dry material is suddenly introduced into an atmosphere having a partial pressure of water vapor or where a moist material is suddenly introduced into a dry atmosphere. Here the resultant differences in the

Jan 1, 1947

By William Sharp

DISCOVERY of new ore in the Eureka district, Nevada, as a result of bold and persistent exploration based on a geologic interpretation of structure has recently aroused wide comment in mining circles. It may therefore be of interest to the profession to have a summary of the historical background and an account of the recent program of development. The mines of Eureka, discovered in the late 1860's, were the first important silverlead mines in the United States. They have a production record of more than fifty-one million dollars.1 After the ore bodies were apparently bottomed in the 1880's, repeated attempts to find new ore were unsuccessful until 1940, when a diamond-drill hole cut a 40-ft width of sulphide ore 1409 ft below the 841-ft level of the Locan shaft. The next hole cut 30 ft, of ore and three additional holes drilled in 1943 and 1944 showed the ore body to be continuous, Shaft sinking to reach and open up the ore body has been in progress since 1945. GEOLOGY Stratigraphy The ore in the Eureka district occurs in a series of Cambrian sediments which is exposed through a thickness of over 6000 ft. The stratigraphic column is as follows:2 [THICKNESS, FI ORDOVICIAN Pogonip limestone (upper part). Thin bedded limestone with some chert. UPPER CAMBRIAN: Pogonip limestone (lower part). Thin-bedded limestone (with shaly limestone and chert).... 425+ Dunderberg shale. Shale (clay and calcareous shale) and thin bedded limestone340+ Hamburg dolomite. Dolomite and limestonegoo+ MIDDLE CAMBRIAN: Secret Canyon shale. Shale and thin-bedded limestone1,035 Geddes limestone. Carbonaceous, flaggy limestone with some shale partings 335 MIDDLE (?) AND LOWER CAMBRIAN: Eldorado dolomite. Dolomite and limestone2,000 LOWER CAMBRIAN: Prospect Mountain quartzite. Quartzite with occasional inter calated conglomerate and shale 1,660+ The Prospect Mountain quartzite has been subdivided into two formations: Upper part, Pioche shale. Shale, quartzite with some intercalated limestone (Lower Cambrian fossils)-200 ft. Lower part, Prospect Mountain quart zite proper-I,460+ft. Total thickness6,695+] Much the most productive of these formations has been the Eldorado dolomite, which yielded more than $42,000,000 at Ruby Hill and an additional amount

Jan 1, 1947

By H. W. Page

Petroleum requirements since V-J day have been appreciably higher than predicted. Foreign operations now exceed maximum wartime levels by about 14 per cent. Domestic operations since V-J day have averaged 92 Per cent of the wartime peak. In spite of maximum foreign refinery runs, large exports of all products, except residual fuel oil, are necessary to meet foreign demand. During the next few years it is expected that foreign operations will continue at capacity, including new installations, but that, because of increases in foreign demand, exports will continue at about their present level. Domestic operations will increase during this period and crude production probably will exceed maximum efficient rates. Even after 10 years some exports probably will be required, but eventually these will be supplanted by increased output of foreign refineries, except for small tributary exports. The increase in domestic requirements will exceed the decline in exports. Unless findings of crude oil exceed present expectations, the increasing demand will be met by increased imports and synthetic methods-—such as the Hydrocarbon Synthesis Process for conversion of natural gas and coal to gasoline and distillates. Catalytic cracking installations will increase as crude availability decreases. This will help to meet the increasing demand for gasoline but will intensify the domestic shortage of residual fuel oil. Eventually larger imports will be required to satisfy the demand for this product. Introduction Under the pressure of the wartime period, there was time only occasionaly to look ahead in anticipation of what the postwar era held for the petroleum industry. Perhaps the general expectation was that a rather pronounced decline in the level of industry petroleum operations would take place shortly after the end of the war, with the impact felt mainly on the economy of the United States- It is of interest now, nine months after V-J day, to take inventory of the near-term situation and see what significant forces are at work. With this as a starting point, it should be possible to engage in something more satisfactory than pure speculation concerning trends in the immediate future and 10 to 20 years ahead. Present and Near-term Situation During the nine-month period following V-J day, foreign crude oil production and rebery operations have actually increased the These activities were at maximum capacity on V-J day but the continuation of drilling programs, the completion of new and rehabilitated refineries and of transportation facilities during the Past nine months have increased the foreign capacity. This added capacity has been fully utilized. Foreign crude oil production in May 1946 is about 14 per cent higher than during July 1945 and refining operations some 12 per cent higher' During the same period there has been a falling off in similar activities within the

Jan 1, 1947

By R. C. Thompson

THE lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 45o-ton operation. GENERAL DESCRIPTION The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1947

Jan 1, 1947