Search Documents

By A E. Waltho, W J. Shaw

Predicting the physical characteristics of various ore types has for long been a difficult problem during mining. Grade control practices tend to concentrate on the chemical grade of the ore. Estimation of physical characteristics such as beneficiation behaviour is commonly limited to the simplistic application of historical averages. Large amounts of geochemical data are often gathered during the exploration and mining stages of a project, especially in ferrous and base metal deposits. In addition to the elements of principal economic interest, samples are often analysed for suites of gangue constituents to determine whether the mineralisation lies within target specifications. This multi-element data is often put to no other use than this simple chemical classification, yet it may present the geologist or metallurgist with valuable insights into the mineral content and physical characteristics of the deposit. Normative mineral estimates have been used as a method for characterising igneous rocks for almost 100 years. The method establishes and applies a set of sequential rules, by which the chemical components of a sample are assigned to mineral components. Provided that it is possible to make some realistic assumptions about the mineral species likely to be present in a rock unit or deposit and their paragenesis, this approach can be extended to a variety of mineral deposits. The geochemical data that are routinely collected when, for example, drilling iron ore and base metal deposits, can be used to derive estimates of normative mineral content. These estimates can be used to characterise physical or metallurgical aspects of the ore, such as density, beneficiation behaviour and metal recovery. This paper examines the application of normative mineral estimates to a variety of practical resource characterisation problems. The potential for predicting the lump and fines proportions of iron and manganese ores is also discussed.

Jan 1, 1999

By D Johns, L Murray

This paper discusses pore pressures in the embankments of tailings dams by comparing real world data with common design assumptions. Assessment of pore pressures has implications on material behaviour interpretation from CPT investigations and, therefore, on the design. For example, the assumption of hydrostatic pressure is conservative for limit equilibrium stability analyses but may be un-conservative in assessing the potential for contractive behaviour and strength loss during shearing. This paper presents some real world data, the investigation methods to determine the pore pressures, and subsequent interpretation of CPT data and material parameters such as the state parameter. It also examines the design implications of assuming a hydrostatic pressure distribution, by comparing results from that assumption with those obtained using the real pore pressures.CITATION:Johns, D and Murray, L, 2018. Characterisation of pore pressure in tailings dams and the implications for design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 239–249 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Joyce, A S. Ray, P S. Thomas, J Haggman

Climate change and global warming present a significant challenge as unsustainable levels of greenhouse gas emissions arising from human activities continue to be emitted. The cement industry is responsible for between five and ten per cent of annual world carbon dioxide emissions; most arising from the manufacture of Portland cement (PC). An effective way of reducing emissions is by incorporating supplementary cementitious materials (SCMs) as partial PC replacements. SCMs are silicate or aluminosilicate based pozzolanic materials which, in finely divided form, combine with water and calcium hydroxide (lime), liberated by cement hydration, to form compounds exhibiting cementitious properties. Pitchstone is such an aluminosilicate and has the potential to act as an effective pozzolan for partial replacement of PC. In North Queensland, Australia, a vast deposit of pitchstone is mined and processed for expandable perlite aggregate. During the classification stage of the excavated natural material, waste pitchstone fines (PF) less than 0.5 mm in size are generated. This study evaluates the waste PF as a viable, eco-friendly pozzolan for the partial replacement of PC. The reactivity of the PF is compared to fly ash (FA), using the pozzolanic compressive strength activity index (SAI) after seven, 28, and 91 days ageing at 20 per cent and 40 per cent PC substitutions. PF was found to be comparable to FA as a pozzolan at 20 per cent PC substitution at all ages tested. However, for the 40 per cent substitution blends significant strength was only achieved at 91 days ageing for the FA blend. The pozzolanic reactivity was also investigated using thermogravimetric analysis to determine the degree of free lime present after 91 days. In all cases where an SCM was added, the free lime was observed to be consumed with increasing age.

Jan 1, 2008

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By M I. Pownceby, S Hapugoda, H Han, E Donskoi, L Lu

Iron ore sinter mineralogy and its associated macro-/micro – structure has a strong impact on sinter quality. At a macroscopic scale, sinter ideally consists of a strong, porous matrix which bonds relict ore nuclei together. Microscopically, the sinter matrix (solidified from the melt part of the initial sinter mix) generally consists of complex calcium ferrites known as SFCA, secondary magnetite and hematite grains (precipitated from the primary sinter melt), glass and silicates. Depending on the conditions under which the sinter structure is formed, two major forms of SFCA with different morphologies are generally recognised, ie fine micro-platy SFCA (usually termed SFCA-I) and coarse columnar/prismatic SFCA. Detailed optical microscope observations of several pot grate and compact sinter samples revealed the presence of a variety of fine, coarse and dense forms of both types of SFCA. The controlled cooling tests revealed that cooling rate has an impact on the form and size of SFCA crystals. In this work, EPMA analysis of SFCA compositions from a variety of pot grate and compact sinter samples are presented. Results show that the SFCA types exhibit a broad range of complex compositions within the system Fe2O3/CaO/SiO2/Al2O3/MgO/TiO2/MnO2. Although SFCA-I and SFCA are known to be crystallographically distinct and with different, well-defined ranges in composition, there was considerable overlap in compositions of the experimental sinter samples. The development of SFCA textures depend on several parameters including the local chemistry and conditions including the maximum temperature attained and the cooling rate, within the sinter bed, thereby suggesting that SFCA identification based on morphology alone may be erroneous.

Nov 8, 2021

By N Guresin, M Rohde

A lead-zinc flotation tailings sample containing silver from BHP Billiton’s Cannington Mine has been characterised to understand occurrences of silver in the tailings by conventional elemental, X-ray diffraction (XRD) and size analyses followed by mineralogical analysis with a scanning electron microscope (SEM) equipped with mineral liberation analysis (MLA) software and the use of an adapted diagnostic leach process originally developed for gold containing materials.The tailings sample contained 67 g/t Ag, 1.8 per cent Pb and 0.52 per cent Zn. The XRD analysis showed that the sample consisted of 74 per cent silicates, nine per cent sulfides, 11 per cent magnetite and small amounts of other minerals such as fluorite, fluorapatite and rutile. The p80 and p50 of the sample were determined to be 106 µm and 38 µm, respectively. The silver distribution was high in the small size fraction with 52.1 per cent of the silver being in the -8 µm fraction. The silver minerals freibergite, acanthite, jamesonite, pyrargyrite and native silver were observed in the mineralogical analysis of the sample by SEM/MLA. The associations of the minerals were intricate and the occurrences of silver were complex. There were finely disseminated silver minerals and also coarser grains of silver minerals in composites with the host minerals. It was estimated that almost 50 per cent of the silver was contained in pyrargyrite, around 14 per cent as native silver and contained in acanthite, 12.5 per cent in galena and around ten per cent in freibergite and jamesonite.These composite particles and the type of the silver minerals present were expected to limit leaching efficiencies of the silver in hydrometallurgical processing. The diagnostic leach tests showed that around 50 per cent of the silver could be recovered by direct cyanidation and higher extractions could be achieved by more aggressive acidic systems.Cyanidation tests were conducted to confirm the findings of the diagnostic leach studies. The investigated cyanidation parameters were time (up to 48 hours), solid to liquid ratio (1:1 and 1:2), cyanide concentration (0.025 M, 0.5 M and 0.1 M) and particle size (p80 of 106 µm, 63 µm and 7.5 µm). The effects of oxygen and lead nitrate were also studied. The tests were conducted at atmospheric temperatures. The maximum silver recovery obtained was about 50 per cent for all the parameter ranges trialled except particle size. The decrease in particle size from 106 µm to 7.5 µm by fine grinding resulted in an increase in silver recoveries from 50 per cent up to approximately 82 per cent indicating that the liberation of the silver grains/minerals is one of the factors affecting the cyanidation recovery of silver in addition to the presence of refractory silver minerals not amenable to cyanidation.Low head grades of silver in the tailings and relatively low cyanidation recoveries of silver (without fine grinding) necessitate a thorough cost analysis for the cyanidation of the Cannington lead and zinc tailings to assess if cyanidation would be a suitable process option for the extraction of silver. It is clear that one of the most important factors in determining the cost feasibility will be the price of silver in the world metal market.CITATION:Rohde, M, Guresin, N and Johnson, N W, 2014. Characterisation of silver minerals in lead-zinc flotation tailings and their response to cyanidation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By E R. Ramanaidou, M S. Piggott

Transport to and handling of iron ore at Port Hedland, Western Australia, results in the generation of airborne particulates that contribute to the atmospheric dust load, with concerns about potential local environmental impacts (eg mangrove swamps) and possible human health implications. Mineral and chemical characteristics of the Background soil samples were contaminated with particles of iron ore as martite octahedra and grains of micro-platy hematite as detected by scanning electron microscopy (SEM) in the 2.5 - 10 ¦m and 10 - 50 ¦m size fractions. Fossilized wood fragments similar to those observed in Yandicoogina fines ore were also detected in some background soil samples. With a predicted increase in demand of channel iron deposits (CID) ores and the inherently dusty Marra Mamba ores (eg West Angelas, MAC, OB29/30/35, Marandoo), in conjunction with particulate emissions from hot-briquetted iron and direct reduced iron (HBI/DRI) processing plants, there is the potential for additional sources of anthropogenic dust to contribute to background levels. Mineralogical and chemical characterisation of the entire range of particulates that could be produced is necessary for a complete understanding of their potential impact on the local environment.

Jan 1, 2002

By B Godel, E R. Ramanaidou, M Verrall

Fortescue Metals Group Ltd Iron Bridge (IB) operation is a magnetite deposit located in the Pilbara region of Western Australia situated around 145 km south of Port Hedland. This Mesoarchean deposit belongs to the 3230 Ma Pincunah banded-iron formations (BIF), a member of the Kangaroo Caves Formation, Sulfur Springs Group (van Kranendonk, 2000).

Sep 18, 2023

By Bhattacharyya A. K

In this paper, the current methods for predicting surface subsidence due to underground coal mining are evaluated first. A single index, called a strata parameter (P), is then proposed to describe the overall character of the undermined strata in the context of surface subsidence. Based on the strata parameter, a method for predicting the maximum surface subsidence for various panel width (w)/depth (h) ratios is presented, which has been tested against specific empirical curves or data from several coalfields in different countries. From the data relating to several coalfields, a linear relationship between the reported average angle of draw and the strata parameter has been established. It has also been found that the strata parameter can be used for studying the locations of the inflection points and the shapes of transverse subsidence profiles.

Jan 1, 1995

Understanding multiphase particulate systems is essential for the further advancement of mineral processing technology. Characterisation, analysis, and simulation of these complex systems provide a fundamental basis for the development of improved mineral processing technology. One of the more recent tools that can be used to help provide a foundation for improved mineral processing technology is high resolution cone beam X-ray micro computed tomography (CT). During the past ten years point-projection X-ray micro CT systems have been used for 3D visualisation and quantitative analysis of multiphase particulate systems. Analysis of packed particle beds containing as many as 30 000 particles can be accomplished in less than three hours with special software to establish the 3D characteristics of each particle in the population and the spatial organisation of the packed particle bed. Now, due to advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. The development of software tools for the 3D characterisation, analysis, and simulation of packed particle beds using high resolution X-ray micro tomography (HRXMT) is discussed including examples of application in the areas of comminution (particle damage and preferential grain boundary fracture), exposure/liberation analysis (liberation-limited separation efficiency, including coal washability), and filtration/heap leaching (pore network structure of packed particle beds and simulated flow using the LB method of computational fluid dynamics).

Sep 13, 2010

By T Kon, K Ohno

Slag foaming is an important control item in the process of refining molten steel. This study aims to investigate the factors controlling slag foaming by observing the bubble formation behaviour resulting from the chemical reaction between iron oxide and Fe-C alloy in the slag. In this study, 0.06 g of Fe- C alloy was introduced at the bottom of a BN crucible, and 6.0 g of slag (SiO2:CaO:Fe2O3 = 40:40:30) was placed on top of it. The crucible was positioned inside an infrared image heating furnace, where the temperature was rapidly raised to 1370°C at a rate of 1000°C/min in a nitrogen stream, and then held at that temperature for a predetermined time before rapid cooling. Following rapid cooling, the internal structure of the sample was examined using a high-resolution X-ray CT device. The spherical equivalent volume was calculated based on the number of observed bubbles and their equivalent circle diameter. Additionally, the relationship between the volume ratio of small bubbles in the slag volume and the distance from the bottom of the crucible was determined, along with the calculation of bubble density and volume ratio. Under various experimental conditions, numerous bubbles with equivalent circular diameters ranging from 200 to 300 μm were consistently observed. The density and volume fraction of bubbles with circular equivalent diameters between 200 and 500 μm showed a tendency to increase as the distance from the bottom of the crucible increased. Bubbles with equivalent circular diameters of 500 μm or more consistently exhibited lower bubble densities, regardless of their height within the crucible. The formation of larger bubbles is attributed to a decrease in iron oxide concentration within the slag as the reaction progresses. However, this is believed to be due to their higher buoyancy, resulting in shorter residence times within the slag and a reduction in the number of encapsulated bubbles.

Aug 21, 2024

By M Khanal, J Qin, B Shen, Y Duan, X Luo

Gaining confidence in interpreting rock and strata properties of the coalmine roof is necessary for design, maintenance, modelling and optimisation of roadways supports. One of the key causes of roadway instabilities experienced in underground coalmines is an extreme variable nature (thickness, competence, discontinuities etc) of the coalmine roof. Normally, the thickness and strength of the roof are characterised with the geotechnical and geological data gathered from exploration boreholes, which are drilled often at considerable distances apart. This limited data cannot capture localised geological variations in the coalmine roof. With this background, this paper explores feasibility of using measurement while drilling concept to perform geotechnical characterisation of the coalmine roof. The parameters, for example, penetration rate, rotary speed, torque, sound, vibration, obtained during the drilling process can provide valuable insights into geotechnical properties. The paper describes the progress of the experimental work conducted at the laboratory on synthesized concrete samples representing various rock strata using a field-scale drilling machine. The samples with and without interfaces have been tested to replicate various underground roof strata. The signals returned from the drill machine, as the drill bit passes through the layers, have been analysed and interpreted to characterise whether the drill response data can differentiate various strengths associated with the rock layers. The initial laboratory results are promising as they show distinct responses of the various sample blocks in a controlled environment. The drilling data can differentiate the synthesized rock samples and detect ‘signatures’ of the roof strength variability and delineation of lithological interfaces (transitions). The weight and torque on the bit vary and show dependency on the strength of the blocks.

Nov 29, 2022

By I Lumsdaine

QNI Pty Ltd operates the Yabulu Refinery located 25 kilometres north of Townsville, North Queensland. The plant treats nickel laterite ores sourced from the Philippines, Indonesia and New Caledonia. The cobalt head grade and overall recovery expectations for the 2001/2002 financial year are 0.161 per cent and 53.8 per cent respectively. Cobalt is a valuable byproduct derived from the nickel refining operation which utilises the Caron Process. Any increases in cobalt recovery that are achieved from the existing relatively low level provide significant improvements to the bottom line of the operation. Towards the end of 2000, a project was undertaken to characterise cobalt losses with the sole purpose of improving cobalt recoveries using a variety of analysis techniques. The Time-of- Flight Secondary Ion Mass Spectrometry (TOF-SIMS û University of South Australia) method was used to verify the presence of surface bearing cobalt species, originating from either co-precipitation or adsorption mechanisms. Cross-section examinations were also performed using Scanning Electron Micrscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDXS). These techniques indicated the presence of high cobalt concentrations (in the order of several per cent) within a select number of roasted and leached ore particles. The phenomenon of cobalt losses due to incomplete leaching within specific ore particles was not widely documented within the Refinery prior to these studies. In order to quantify losses via this mechanism, Mineral Liberation Analysis (MLA û JKTech Centre) was also performed on key samples. This paper serves to document a systematic approach in determining the source of significant valuable mineral losses in an established, operating plant. It discusses the use of a variety of analytical techniques, which have been adapted for the minerals processing industry, but are strongly relevant for plant investigations in the hydrometallurgical industry.

Jan 1, 2002

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Hunt

A critical aspect of geometallurgy is quantifying mineralogical and textural relationships that affect mineral processing (eg, liberation and recovery). However, to date, this has been an expensive and time consuming venture and only minimal amounts of this type of data are typically available to be included in the mine planning process. Our research is focused on developing methods that will produce the required mineralogical and textural data rapidly and inexpensively. New methods of characterising liberation potential from image analysis of coarse particulate material and direct small-scale flotation measurement are compared with measurement of liberation at final grind size (ie conventional tests on MLA). The new tests are designed to rank the liberation potential of samples in order to classify an ore deposit into domains of low, medium and high liberation potential. This parameter can then be used to adjust the cutoff used to differentiate ore from waste. Results to date show that all tests provide the same ranking for the samples. The measurement based on coarse particulate material compares favourably to the results from MLA analyses on the same samples. Further work is being carried out to determine which of the tests will be the most effective in terms of time, effort and cost

Sep 5, 2011

By A Scott, I Onederra

A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful empirical or engineering models are currently available to blasting engineers and consultants, while more sophisticated approaches using mechanistic and numerical descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The fragmentation resulting from any blast will be heavily dependent on the properties of the rock mass being blasted; however, most empirical models rely on ‘rock factors’ generated from simple rock mass properties to describe the influence of the rock on the blasting outcome. In contrast, mechanistic models need explicit rock mass properties that require sophisticated laboratory measurements and detailed structural data if realistic outcomes are to be generated. The fragmentation modeller is caught between excessively simple rock mass descriptions for the empirical models and excessively complex data requirements for the mechanistic models.This paper briefly reviews the basis of a range of fragmentation models and the rock mass properties on which they rely. Shortcomings in the way that the mining industry tends to characterise the blasting properties of rock are discussed and some practical approaches are described to quantify these properties in both operating and greenfield mining environments. Case studies are presented where specific additional breakage properties and modelling features have been needed to generate a useful description of the fragmentation achieved.CITATION:Scott, A and Onederra, I, 2015. Characterising rock mass properties for fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 149–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Scott, I Onederra

Most iron ores occur in mine benches as complex mixtures of lithologies and ore types. This significantly complicates their characterisation for both blast design and fragmentation modelling. A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful engineering models are currently available to blasting engineers and consultants, and more sophisticated approaches using mechanistic descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The engineering or empirical models that are in more general use within the industry, such as the Kuz-Ram model, require appropriate data if they are to generate useful fragmentation predictions. Some of these models have reached significant sophistication and have made very useful contributions to both routine blasting operations and the exploration of new blasting paradigms. However, these models struggle to adequately deal with rock that is as complex as iron ore. This paper reviews the characteristics of the most successful blast fragmentation models available to the industry and discusses approaches to the derivation of suitable rock mass properties to adequately describe blast fragmentation in a range of iron ores.CITATION:Scott, A and Onederra, I, 2015. Characterising the blasting properties of iron ore, in Proceedings Iron Ore 2015, pp 481–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By F D. I Hodgson

Twenty-seven observation test pits were excavated at four different spoils dumps at three collieries in the Witbank Coalfield. The holes were dug into the upper three metres of the spoils to ascertain if any weathering profiles, variation with age or influence of topsoil covering could be gauged. Samples from these holes were also subjected to laboratory testing (ABA, humidity cells and mineralogy on several selected samples). The test pits showed that there was a good correlation between in situ paste pH-values and ABA results for samples taken from the pits. At all the collieries, no correlation between age of spoils and in situ acidity could conclusively be drawn. The depth of soil cover also appears to be a minor consideration in determining the eventual acidity of the spoil. In the pits where acidity was found, the weathering was evident when contrasted to areas still buffered. It is unclear if the weathering leads to the acidity or vice versa, as the soil covering appeared to be similar. The spoils proved to be extremely variable with regard to particle size and material on a micro and macro scale. Evidence from most of the holes suggested that there was enough water contained in the fine material in the spoils to support the initiation of acid generation. Conclusions from this investigation are that the mineralogy of the spoils is the most important factor in determining the eventual occurrence of acidic hotspots, and that prior characterisation and selective handling will provide the best management practice for these spoils.

Jan 1, 2003

By L Matthews, D O’Dea, P C Hayes, J Manuel, B Monaghan, T Honeyands, D Pinson, J Leedham

Many different approaches have been used in the past to characterise iron ore sinter mineralogy to predict sinter quality and elucidate the impacts of iron ore characteristics and process variables on the mechanisms of sintering. Characterisation techniques include optical image analysis and point counting, X-ray diffraction and scanning electron microscopy. Each technique has its advantages and disadvantages depending on the objectives of the measurement. It is generally acknowledged that silicoferrite of calcium and aluminium (SFCA) is very important to the quality of the sinter produced; however, strict definitions of the phases and textures of SFCA are not generally agreed. This paper summarises the state-of-the-art in sinter characterisation applied in Australia by both academics and industrial researchers. The results from various techniques are compared and the relationships between the measurement results are discussed.CITATION:Honeyands, T, Manuel, J, Matthews, L, O’Dea, D, Pinson, D, Leedham, J, Monaghan, B, Li, H, Chen, J, Hayes, P C, Donskoi, E and Pownceby, M I, 2017. Characterising the mineralogy of iron ore sinters – state-of-the-art in Australia, in Proceedings Iron Ore 2017, pp 49–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The purposes of defining the mining environment for underground mass mining and the uses of characterisation data are outlined. The requirements for data in the areas of geology, surface and groundwater hydrology, topography and environmental constraints and geotechnical studies are identified. Emphasis is then placed on the collection and interpretation of geotechnical data for establishing the in situ stress regime and for rock mass characterisation. Methods used for diamond drilling, core logging, borehole logging, data analysis and presentation, rock mass modelling and rock mass classification are outlined. Finally, recent and potential advances in the state-of-the-art are identified in areas such as geophysical methods, measurement while drilling, computerised data collection and analysis, rock mass modelling, in situ stress measurement data presentation and interpretation, and some applications of rock mass characterisation data.

Jan 1, 2000