Search Documents

By J Robertson, D Williams, H D. Plewes

The co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material (Co-Mix) with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retaining capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimise acid generation and metal leaching. When compacted, Co-Mix materials have low volume change characteristics with respect to total stress and matric suction together with high shear strength. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures or a full depth waste repository. The theoretical properties of Co-Mix blends are investigated. The results of a laboratory program to characterise the physical and hydraulic properties of co-mixed tailings and waste rock are presented. Various ratios of tailings were blended with different waste rock materials. Hydraulic conductivity tests were conducted at confining pressures ranging between 0 and 400 kPa. The saturated hydraulic conductivity for the Co-Mix materials was found to vary between 4 + 10-5 m/s and 5 + 10-9 m/s depending on blend ratio, waste rock type and confining pressure. These results together with other physical properties show excellent hydraulic and strength characteristics can be achieved for Co-Mix materials.

Jan 1, 2003

The estimate of an ore reserve is a vital statement made about a mineral occurrence by an evaluator. It is important that such a statement communicate reality to all groups involved in a mining project, be they technical, financial, company directors, Stock Exchanges or the public. Ore reserve statements should state both resources and recoverable ore reserves. Resources may be important in very long term considerations, (because mining, metallurgical technology and economics change with time) but recoverable reserves are todays reality. The important factors contributing to recoverable reserves (in a general sense) are geology, mining method (and its impact on dilution and ore loss), metallurgical recovery, costs and commodity prices. These all need to be reflected in the ore reserve statement. In this paper recoverable ore reserve concepts across a wide range of orebodies are considered and discussed with respect to geology, mining method and ore reserve calculation procedures.

Jan 1, 1987

Geosynclines have been well studied for many years, but very little has been written about the concepts of sedimentary basins in spite of the vast amount of data available. They have been regarded, perhaps, as well- understood intuitively, and therefore not worthy of study. Many of the fundamental concepts of geology were developed during the 19th Century with the construction of coal mines, canals and railways. It was a happy chance that led railway engineers in the early days to think that trains could not climb any but the smallest gradient, so, in Britain at -least, numerous railway cuttings and tunnels were made. These exposed to view and study, in a better form than Nature usually provides, a great deal of interesting geology. Because of the lack of literature about the concepts of sedimentary basins, it is not possible to be sure what the early geologists thought. It seems that sedimentary basins were regarded as recording a history of subsidence during the early stages, when a transgressive sequence accumulated; and a history of uplift during the later stages, when a regressive sequence accumulated. It seemed axiomatic that the age of folding and faulting was younger than the rocks folded or Faulted.

Jan 1, 1987

High sulphur volcanic-hosted hydrothermal environments are favourable geological environments for gold mineralisation. Numerous world-class gold deposits including Pueblo Viejo (Dominican Republic), Goldfield (Nevada), EI Indio (Chile), and Wa

Jan 1, 1994

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D A-F Batchelor

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.South-East Asia represents the world’s most productive tin province, mainly from placers. Kalimantan has been a major diamond producer, while in the 1980s a placer gold rush occurred in Indonesia and Malaysia. Reviewing extensive geological and mining data highlights phenomenal palaeo-environmental changes in the Sundaland region, interpreted to be responsible for generating ‘giant’ placers. Correlation of the Late Cainozoic stratigraphy has been facilitated from mine exposures and drill holes distributed throughout Peninsular Malaysia, the Indonesian Tin islands and Kalimantan, including contiguous marine areas with extensive shallow seismic profiling data. Knowing the association of rich placers with palaeo-environmental episodes and stratigraphical units has been helpful to facilitate their discovery. All three placer commodities responded similarly to region-wide landscape evolution following Mio-Pliocene high sea levels. Commencing with major regression, important stages comprised: a long period of landscape stability with deep weathering during the maximum Sundaland extent gradually rising sea levels/precipitation initiated slumping of mineralised regolith to form fans, later reworked by braided streams with aggradation (Old Alluvium); during episodic pluvial periods downcutting upgraded placers significant change occurred around Middle Pleistocene time with peneplanation and pedogenesis from Late Pleistocene time ‘modern’ fluviatile deposition (Young Alluvium) filled incised V-shaped valleys.Placer seams show systematic variation in stratigraphic position, in particular cassiterite especially occurs in the Old Alluvium (equivalent Upper Dahor Formation in Kalimantan). Gold is commonly richer in gravelly younger deposits, partly because of secondary precipitation within permeable alluvium. Reworked diamonds are predominantly concentrated especially in younger fluviatile alluvium.CITATION:Batchelor, D A-F, 2015. Conceptual exploration for tin, gold and diamond placer deposits in ‘Sundaland’ (Indonesia and Malaysia) by understanding the late Cainozoic stratigraphic context, in Proceedings PACRIM 2015 Congress, pp 499–506 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

In November 1969, New Zealand Steel Ltd pioneered the commercial use of the SL/RN solid fuel direct reduction process to make sponge iron as a feed material for electric arc furnaces. Serious process problems with the use of green balls and coal injection were progressively overcome. The process was developed by New Zealand Steel along a radical route, of feeding the fine grained raw ironsand concentrate and coal directly to the kiln. Contemporaneously with this development of direct reduction, steelmaking process innovations were made that enabled the arc furnaces to operate successfully with the high volumes of acid slag. The further expansion of New Zealand Steel's primary steelmaking capacity to replace the currently imported hot and cold flat rolled products is under consideration. The requirement to produce about 600 000 tonnes of steel slabs will be an opportunity to further modify iron and steel making plant and processes to optimise the economics. The conceptual and preliminary engineering selection of options is described.

Jan 1, 1980

By C. P. BATES

In November 1969, New Zealand Steel Ltd pioneered the commercial use of the SL/RN solid fuel direct reduction process to make sponge iron as a feed material for electric arc furnaces. Serious process problems with the use of green balls and coal injection were progressively overcome. The process was developed by New Zealand Steel along a radical route, of feeding the fine grained raw ironsand concentrate and coal directly to the kiln. Contemporaneously with this development of direct reduction, steelmaking process innovations were made that enabled the arc furnaces to operate successfully with the high volumes of acid slag.

Jan 1, 1980

It is always difficult to sum up an open forum adequately and instantaneously, so, with the privilege of hindsight, and also with some time to reflect, I am exercising the Chairman's prerogative to put together my view of the overall conclusions. Hopefully, these may provide a focus for each Institute to formulate its own programme with respect to mineral industry education. First, in answer to the question, "Should there be Schools of Mines?", there was a very clear 'yes'. However, I reiterate what I said in the introduction to this forum, specific professional education for the mineral industry exists only because the mineral industry sees a need and wants it. If the mineral industry should decide that it does not need professionals with specific mineral industry training, then such training will cease to exist. As alluded by Dr Hackett, if such training ceases to exist, one must then question the need for Institutes of Mining and Metallurgy. Now, there's some food for thought! Specialist schools of mines (metallurgy and geology) can only exist in an environment of genuine interaction with, and support by, industry. For their part, schools of mines, used here in a generic sense, require leadership that is strong but responsive to industry needs. It is the leader that puts his stamp on a school, and, to a large extent, determines whether that school is 'good' or only 'mediocre'.

Jan 1, 1986

By R Barritt

Remedial options for a waste rock dump (WRD) were considered as part of closure planning studies at an active mine in Western Australia. To minimise the impact of any seepage from the landform it was determined that placement cover system utilising the moisture ‘store-and-release’ concept was appropriate. The purpose of the cover system was to:•Reduce net infiltration of meteoric water to attenuate peak concentrations for contaminants of concern in natural receptors to levels that can be assimilated without adverse impact to the surrounding ecosystem; •Provide a growth medium for establishment of a sustainable vegetation canopy; and •Improve current quality of surface water runoff from waste storage areas.The project comprised several phases of work: materials characterisation, numerical soil-plant-atmosphere (SPA) modelling and finally cover system construction and monitoring equipment installation.CITATION:Barritt, R, 2018. Conclusions from long-term cover system performance monitoring – a case study, in Proceedings Life-of-Mine 2018, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

At the LKAB, Iron Ore Mine, Kiruna, Sweden a preliminary investigation into the reliability characteristics of a fleet of load-haul-dump machines has shown that the hydraulic system is one of the most critical parts. Therefore, hydraulic system was selected for study and analysis through condition monitoring devices so that failure can be controlled or at least the failure consequences can be minimized.The hydraulic system has two different problems; one is that the contamination level is too high and the other is high temperature during operation. At high temperature, seals and tubes are a problem, because they stiffen due to carbonization, which leads to increasing leakage. The pumps and restrictions were responsible for the main temperature increase.

Jan 1, 1991

By J A Evans

A well-maintained and low cost mining operation today requires the use of condition monitoring techniques. At ERA - Ranger Mine oil analysis, vibration monitoring, infra-red themtography, and performance analysis have been successfully applied over the last four years to lower operating and maintenance costs. All condition monitoring is scheduled through a comprehensive in-house developed maintenance management system known as the Engineering Information System (EIS). (EIS) is used extensively at Ranger to ensure consistent frequency and recording .of all condition monitoring data. This paper provides an insight into the benefits of condition monitoring and explores the future direction for condition monitoring techniques at Ranger.

Jan 1, 1994

By Sjaw WJ

Conditional simulation is a set of geostatistical tools that is becoming popular as powerful personal computers make the use of these tools less costly. The more familiar set of tools for spatial estimation has a number of varieties (eg Ordinary Kriging, Simple Kriging, Multiple Indicator Kriging, etc) each suited to particular solutions of the problem of estimation, for example predicting the average grades of blocks in a region from more or less sparse data. Similarly, conditional simulation has a number of varieties, discussed in this paper, which in various ways address the problem of characterising the variability of a deposit between the known data locations.Conditional simulation can provide a number of equiprobable images of a deposit, at a finer resolution than would be economic or practical to sample, and that can be constrained by various criteria (which may be geological, statistical and geostatistical), to ensure that the images reasonably represent the deposit. These images can then be used to assess the risk involved in various practical mining decisions. Examples are provided where conditional simulation has been used for validating resource estimate parameters, optimising grade control sampling grids, and for ore block optimisation for mining grade control.

Jan 1, 1997

By A Richmond

"In some lode-style gold deposits the geological (lithological) uncertainty may have similar economic significance as the grade uncertainty. In the absence of precise knowledge of the deposit geology, geological models of these types of deposits that are used to constrain spatially the estimated (or simulated) grade values may influence significantly the contained metal. Methods for assessing geological uncertainty quantitatively are rarely considered due to their perceived inability to consider exhaustive geological interpretations, and resulting models that often appear geologically unrealistic. Furthermore, should the lodes have been subjected to folding, or where the mineralisation continuity does not follow a planar orientation along strike or down dip, standard methods of variography and interpolation using linear vectors in space often do not provide a good representation of continuity. An alternative approach is to relate spatial samples from adjacent drill holes using an unfolding plane.The paper demonstrates conditional simulation of the geometry and gold grades of a folded lode-style deposit where:simulation of lode geometry considers explicitly the geologistÆs interpretation, andsimulation of gold grade values that consider explicitly the folded nature of the lodes.The results are contrasted to the traditional approach of linear vectors in real space for a single lode interpretation.CITATION:Richmond, A, 2012. Conditional simulation of a folded lode-style gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

Conditional simulation is a branch of geo- statistics which allows the simulation of a mineral deposit so that predictions can be made about the variability of some particular parameter of the deposit. A summary of the general principles, advantages and limitations of conditional simulation is presented together with an example based on coal seam thickness.

Jan 1, 1981

By M G. Aylmore, L W. de Klerk

Roasting of refractory gold ores has been a commercial process for many years. Improvements in design of fluidised bed roasting technologies and low capital and operating costs compared with other refractory treatment processes can potentially make roasting a viable option.However, gold extraction from roasted ores carried out on laboratory scale equipment often invariably yields lower recoveries than other processes such as bio-oxidation or pressure oxidation. Non-optimal laboratory roasting conditions can incorrectly write roasting off as a process option.Low gold recoveries from the cyanidation of calcine products from roasting can often be attributed to roasting conditions not favouring gold liberation and agglomeration processes, particularly if lockups of elements such as arsenic are being pursued for environmental reasons.This paper reviews the conditions favoured for gold agglomeration and accessibility of gold to cyanide, test conditions to achieve gold liberation and agglomeration on laboratory scale and designs that incorporate staged decomposition and roasting to make roasting a more commercial option.CITATION:Aylmore, M G and de Klerk, L W, 2013. Conditions and design considerations for maximising recoverable gold in roasting of refractory gold ores, in Proceedings World Gold 2013 , pp 375-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The mechanism of caving is of interest to the mining engineer only in areas where he is directly concerned. One area is surface subsidence which is outside the scope of this paper. Another area is at the face where coal is being extracted and where control of caving is of vital importance. Coal mining systems have been developed with many considerations in mind, but in this list of considerations, strata control has seldom been given much importance. Research is in progress in Australia to endeavour to determine an optimum sequence for coal extraction underground. As information becomes avail- able from this work it is hoped that appropriate methods of controlling caving in various strata conditions will be devised. When this is done, equipment may be introduced to permit the mining operation to proceed under optimum conditions for strata control, rather than devising a mining procedure to suit the equipment available and methods developed for other reasons.

Jan 1, 1974

By P Holtham, K Duffy, B, W Valery, E Tabosa, rade

Pre-concentration has potential to significantly improve Mineral Resource efficiency by removing gangue early in the process, before energy intensive and expensive comminution and fine processing. However, there are numerous options for pre-concentration and the performance and benefits of these are very case specific. To determine the best option for a particular deposit and to successfully integrate it into the overall mining and processing operations requires comprehensive evaluation. This needs to consider orebody suitability, technology capability and economic viability. The in-situ variability of a deposit and how it is influenced by mining methods and the liberation size of gangue are key factors which are generally not well understood. Geostatistical methods provide an insight into orebody variability, and the overall selection of any pre-concentration solution must be an integrated approach between geology, mining and processing. Many pre-concentration evaluations investigate the potential of just one option. Technology selection should start wide and may include: selective mining, pre-screening (with or without selective blasting), sorting (bulk and or particle), coarse gravity separation (e.g. jigging, DMS), coarse particle flotation, magnetic separation, etc. The upgrade performance of these processes is very ore specific and should be determined from testing, with detailed multi-component modelling used to determine the overall process performance. Many of these pre-concentration processes require significant ancillary equipment, feed preparation and materials handling. It is important to realistically estimate all costs to understand overall economics and select the best option. Some examples showing evaluation and comparison of pre-concentration options are presented in this paper. These include assessments of in-situ variability using geostatistical tools, process modelling of pre-concentration options and overall performance, preliminary layouts and cost estimates, and economic evaluations.

Nov 10, 2020

By C J. Greet, J Kinal, C Hitchen

Following the successful completion of a marked ball test defining the potential wear benefits the high chrome alloys may offer against forged steel, as well as laboratory test work investigating changes in pulp chemistry and improvements to metallurgical performance, a plant trial was commissioned at NewcrestÆs Ridgeway concentrator. The paper briefly describes these results.Newcrest decided to convert their media charge by the top-up method. To monitor the trial a sampling protocol was put in place whereby the pulp chemistry was monitored before, during and after the purge. The metallurgical shift data was analysed using various statistical methods to determine if the metallurgical performance had improved with the change in grinding media. While the analysis indicated that the metallurgy had improved, not all of the benefits could be assigned to the change in grinding media alone. However, the combination of reduction in media wear and the increases in copper and gold recoveries suggested that it was economically viable to operate with high chrome grinding media.As with many trials of this nature the prevailing economic conditions are fluid and a decision was made to revert back to forged steel grinding media in an effort to reduce operating costs. It was further agreed that Magotteaux could monitor the pulp chemistry and metallurgical changes in this reverse trial to confirm the results observed in the earlier conversion to high chrome grinding media.CITATION:Greet, C J, Hitchen, C and Kinal, J, 2012. Conducting high chrome grinding media trials at NewcrestÆs Ridgeway Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 56-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D Reid, A Fourie, J Ayala

This paper discusses cone penetration test correlations for loose gold tailings that were developed within a critical state soil mechanics framework. The development of a new calibration chamber for cone penetration testing that consists of a modified triaxial cell is described. Some of the early development and commissioning issues that were encountered, as well as the solutions adopted are outlined, including the system to prepare the samples and to acquire high-quality data from the testing. Also, the triaxial laboratory testing required to achieve the critical state line is described, including some of the basic precautions considered necessary as good practice. Additionally, the system adopted for volume tracking of the calibration chamber sample is described, which is essential for ensuring a reliable state parameter comparison against the acquired cone penetration test data. Finally, some laboratory test data from the calibration chamber is plotted against the soil behaviour type charts currently available from various authors.

Jul 1, 2021