Search Documents

By G Gopinath, R Balachander, H S. Venkatesh

This paper describes in detail the controlled blasting adopted and the measurements undertaken for the successful excavation of large twin tunnels under a shallow cover for a six-lane highway project in India. The tunnels are D-shaped, each 15 m in diameter, and the cover between the tunnels and the existing railway track was about 14 m. These twin tunnel tubes were characterised by two separate three-lane carriageways for each direction of traffic, and were planned with about 25 m of reinforced cement concrete (RCC) portals at the entrance and exit of the tunnels. The major challenge of the project was the blasting of tunnels in rock below an operating railway line. As the tunnels approached the area below the railway line, the ground vibrations were monitored vertically above the blasting faces and on the railway track sleepers. Vibration intensities between those generated from tunnel blasting and those from the movement of the trains were compared, and it was found that the vibrations from blasting were lower than those from the moving trains. Though the permissible level of ground vibration based on the Indian Standard (IS) code happens to be 70 mm/s, the maximum charge per delay was calculated restricting this limit to 50 mm/s. This ensured that the vibrations in the vicinity of the railway tracks never exceeded the prescribed limit of 70 mm/s. The surface ground settlement before and after the blasts were also measured using an optical levelling instrument, which confirmed that there was no significant impact on the surface movements due to blasting. Extensometer readings inside the tunnels showed that there was no deformation in the tunnel. These twin tunnels are now operational and are providing faster connectivity with safety.CITATION:Gopinath, G, Venkatesh, H S and Balachander, R, 2015. Controlled blasting for twin tunnels with a shallow cover under an operating railway line, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

A brief review of the problems in ventilating and cooling deep and hot Australian mines is presented. An overview is given on the development of the controlled partial recirculation concept. The main part of this paper describes the first majo

Jan 1, 1994

Conventional treatment of oxide and oxidised sulphide minerals by flotation involves the use of sodium sulphide for sulphidisation. Sodium sulphide is generally applied in a "slug" dosing fashion with manual regulation. However, it is recognised that "over addition" or "under addition" of sulphidising reagent can result in poor flotation recoveries. Thus, control of sodium sulphide additions is an important aspect of a sulphidisation circuit, both commercially and metallurgically. In any plant where the flotation feed is "constant" it is possible to operate at a constant rate of addition of sodium sulphide. In actual plant practice, however, it is difficult to maintain a truly constant feed for any reasonable duration because this implies not only a constant feed-rate, but also constant mineral composition and particle size range. These factors can vary significantly and ideally require corresponding variations in the additions of sodium sulphide to maintain optimum recoveries. To cope with variations in the feed, it is essential to have automatic rather than manual regulation of the sulphide reagent addition. The CPS process achieves this control by utilising a sulphide ion-selective electrode as a control instrument in sulphidisation. The CPS process which uses a selective electrode, enables the sulphide ion concentration in the flotation pulp to be monitored and controlled continuously throughout the stage of sulphidisation.

Jan 1, 1989

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Controlled recirculation of nine ventila- tion air is becoming an acceptable practice world-wide. A brief review of operating and planned schemes is given which illustrates the various purposes for using controlled recircu- lation in different types of mines. A de- tailed description is given of the operating and proposed schemes on South African gold mines. This is followed by a description of some theoretical and experimental work which has recently been carried out into certain important aspects of controlled recircula- tion. This includes: safety systems, dust filtration, blast contaminant removal, radia- tion hazards and the development of an expert computer program for the design of controlled recirculation systems.

Jan 1, 1988

By Tuck M. A

The increasing depth, mechanisation and distance of working areas from surface connections places an ever greater contaminant burden on ventilation airflows. Some British Coal mines are already experiencing significant problems in providing adequate climatic conditions in the working areas and have had to introduce air conditioning. Previous work has shown that in mines of low to moderate virgin strata temperature the application of controlled district recirculation could serve to improve climatic conditions at the working area.

Jan 1, 1988

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Silver is one of the three major metals produced from the Broken Hill mines. The accurate determination of the silver in these ores, therefore, is of economic importance.With due appreciation of the divergence of opinion of many who are interested in the subject of the determination of silver, the writer has been prompted to present the results of some recent experiments on silver losses during cupellation and conclusions from these experiments in the present paper. The losses of silver in the fire assay for this metal are due to silver retained in the slag during the fusion or scorification of the ore, and to silver volatilized from, and absorbed by the cupel during the process of cupellation.The literature describing the results of experimental work on silver losses due to the above causes is extensive, and the general conclusion of these experiments is that the silver lost in the slag is small, but that lost by cupellation is larger and more variable.The term cupellation loss in this paper refers to the total cupellation loss, no distinction being made between the absorption and volatilization losses.Volatilization loss is shown by King to be 0.5% of the total cupellation loss and, as it is generally accepted among assayers as being only a small fraction of the cupellation loss (3) (5), it will not receive further consideration in this paper.The factors causing the loss of silver by cupellation and the precautions to be obs~rved to reduce the loss in this operation are described in (1), (2), (3), (4) and (5). The...

Jan 1, 1940

By W A. Tchernykh, R P. Strelnikova

In connection with the fact that technology of ore mining by caving system is often used when mining of deposits, characterising by low stability of surrounding rock mass, the main problem for such ore mines is ensuring stability of mine workings, placing in a zone of influence of winning operations. Besides natural disturbance of ore mass, stability of workings depends on the dynamic effect of blasting operations and also on the dynamic effect of structural blocks detaching from the ore mass and colliding with crests of ore pillars in the bottom of a chamber. Decreasing of dynamic stresses may be achieved by way of creation of a compliant porous screen or an ore cushion in the chamber bottom. It is established that maximum levels of compression take place when the first impact impulse occurs, and after that increase of compression of protective slice decreases. Necessary thickness of screen slice was substantiated theoretically with due account of height of structural blocksÆ fall, their mass, deformation modulus of ore mass and ore cushion.

Jan 1, 2003

By T Howard, J E. Everett

BHP Billiton Iron Ore has replaced the conventional product quality control batch system at Yandi with the Continuous Stockpile Management System (CSMS) centred on a fully integrated æcontinuousÆ stockpile flow from mine planning through to port reclaiming. With increasing tonnage rates, tight operational coupling associated with the original batch system caused production interference which achieved final product quality but in an increasingly inefficient manner. This innovative approach places a continuous emphasis on product grade control and takes full advantage of the most appropriate blending opportunities of the mine to port planning and production system in order to reduce the natural variability of the ore to an acceptable level. To implement continuous control, product variability throughout the process is classified as long-term and short-term. Long-term variability is best controlled through the monthly mine planning process which determines monthly grade targets while taking into account optimum mine development. In the past, attempts to control long-term variability were made at the port through selective stockpiling and reclaiming which reduced operational efficiency. Short-term variability is best controlled around the monthly mine grade target by daily mine production scheduling, train sequencing, stacking into port stockpiles of appropriate size and systematical stockpile reclaiming. The implementation of the new system has maintained customer accepted shipping grades and has provided significant improvements in resource utilisation, operational efficiencies and costs.

Jan 1, 2002

By Q Liu

Open stoping is one of the widely adopted methods in underground bulk mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sublevel in the ore zone and blasted ring by ring into a stope for excavation. A mass stope blast may involve blasting rock from multi-level drift rounds and displacing the muck to specific locations in order to allow safe and easy access for ore removal. This paper presents a strategic mass stope blast that took place at a large lead and zinc underground mine in eastern Canada. The blast consisted of more than 800 holes drilled in six blocks from three different sublevels. The challenge lay in the control of ground vibration and muck movement using precise timing to complete the blasting within 6.5 seconds. During this time span, sufficient voids were created in each level to allow the muck to move from the upper to the lower levels in sequential order across the six mining blocks without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement as well as the application of electronic detonators. These detonators provided the means to accomplish the desired firing sequence including a drop raise blast at the start of the mass blast. The modelling concept is also described in the paper.

Jan 1, 2005

By M J. Schultz, R L. Rude, D M. Tomko

The US Mine Safety and Health Administration (MSHA) conducted compliance assistance diesel particulate matter (DPM) sampling throughout the underground metal and non-metal mining industry. Based on that sampling, MSHA identified mines that were having difficulty meeting the DPM limit. To provide further assistance, MSHA then visited approximately 60 of the mines that were experiencing difficulty complying with the DPM standard. As part of these visits, DPM exposures were measured and control technologies for DPM were observed and assessed. Controls consisted of ventilation, clean engines, environmental cabs, alternative fuels, diesel particulate filters (DPF) and work practices. The focus of the follow-up compliance assistance visits was to assess control effectiveness and to make recommendations to mines experiencing difficulty in meeting the DPM standard. At each mine visited, the ventilation controls were evaluated, engine emissions were determined for equipment in use, environmental cabs were examined, and operational practices were noted. Additionally, control technologies, including alternative fuels and DPF were evaluated in several mines. A comparison was made of mine and section airflow to equipment particulate indices. Based on engine emissions, horsepower and operating time, the contribution of individual engine emissions to total emissions was made. Environmental cab integrity, positive pressure and air filtration systems were checked and operational practices relating to DPM exposure were assessed. This paper summarises the preference and magnitudes of controls that were typically used or needed for successful control of DPM. Additionally, results of the assessments of alternative fuels (including bio-diesel and water emulsion fuels) and DPF are presented.

Jan 1, 2005

The Fosterville Goldfield has a modest past production (0.3 Moz), but is now emerging as a significant goldfield (2.6 Moz resources, including 1.1 Moz reserves) with implications for exploration within the orogenic gold provinces of the Lachlan Fold Belt in Australia and the Buller Terrane on the West Coast of New Zealand. Fosterville is located 20 km east of the 22 Moz Bendigo Goldfield and is geologically similar to other Victorian goldfields, however the nature of the gold mineralisation differs significantly. Unlike other Victorian goldfields there is no primary free gold at Fosterville. The gold occurs in as sub-SEM resolution particles, in fine grained arsenopyrite and pyrite crystals disseminated through the wall rocks in fault controlled quartz-carbonate vein stockworks. The Fosterville Goldfield comprises several subparallel fault systems striking 340¦ over an exposed strike length of 28 km. The Fosterville Fault system comprises the west dipping (~75¦), reverse Fosterville Fault and several less steeply west dipping splay faults formed in the footwall. The splay faults extend through east dipping beds from the Fosterville Fault across a syncline hinge into stratigraphically controlled positions on the west dipping limb of the syncline. The predominant control on gold mineralisation is the intersection of the bedding on the east dipping limb of the syncline and faulting which, is in turn controlled by the orientation of bedding in the west dipping limb of the syncline. The mineralised shoots are thus subparallel to the plunge of the syncline and show a plunge reversal about a culmination in the footwall syncline. This provides a very powerful exploration tool with bedding û cleavage intersection lineations measured in outcrop and oriented core indicating the plunge of mineralisation. Mineralisation is also, albeit less commonly, controlled by local variations in strike and dip of the host fault and at metre scale by host lithology. As the faults and mineralisation are stratigraphically controlled, detailed stratigraphic interpretations are essential to provide control on structural interpretations for resource modelling. Compared to other Victorian goldfields, the Fosterville Goldfield formed later (385 Ma to 360 Ma cf 440 Ma), at lower temperatures and at shallower depths (fluid inclusion studies of Au associated veins suggest vein formation at ~270¦C (range 140¦C to 385¦C) and at depths of 2.6 - 5.7 km).

Jan 1, 2005

The formation and distribution of gold placers in active collisional mountain belts are directly related to the tectonic, topographic, climatic and erosional constraints prevailing on either side of the orogen at the time of placer formation. In the absence of pre-existing placer deposits, these factors combine to concentrate placer development on the side of the orogen facing the prevailing winds, where most of the erosion and uplift occurs. Drainage network changes and glaciation can significantly alter placer distribution with respect to source areas within the orogen. After collision stops, placer formation will proceed on both sides of the orogen as exhumation of the mountain belt ensues. Incorporation of pre-existing placers formed on ancient mountain belts into younger placers in subsequent orogens, may be recognised by anomalous placer distribution compared to the above model. Most of the relatively young giant placers such as those inNew Zealand, Chile, Bolivia and Columbia, exhibit these general patterns. Their character and mode of formation have important implications for the formation and distribution of much older placers, such as those in South Africa's Witwatersrand Basin.

Jan 1, 1996

By Eupene GS

The Early Proterozioc Pine Creek Geosyncline hosts a large number of gold showings. Mineralisation types include stratiform, synsedimentary deposits within iron formation and carbonaceous mudstone; disseminations in granophyric intrusives; and quartz vein related concentrations in the form of shear fillings, saddle reefs and stockworks. Stratiform gold deposits preferentially formed near penecontemporareous faults during periods of basin instability. Intrusive basic magmas later assimilated some stratiform mineralisation and subsequently redeposited it within differentiated phases. Gold was again remobilized during regional deformation and metamorphism. Stratiform mineralisation was upgraded insitu in high strain zones and gold was mobilized into metamorphic fluids. Fluid induced fracturing during prograde metamorphism and later uplift caused the deposition of extensive gold rich vein systems. The genetic relationship between gold deposit types is reflected in the clustering of showings along regional anticlines, and provides a powerful exploration tool. The large volume of 'exhalative'òmaterial in the Geosyncline with elevated gold content suggests significant economic stratiform mineralisation may be present, and probably provides a source for later disseminated and vein deposits.

Jan 1, 1984

Determining the controls of high-grade mineralisation at Vera Nancy requires careful data collection and assessment on a global and specific deposit basis. The techniques developed over 60 years ago to analyse structure, grade and width data are just as applicable today and can be enhanced using modern geological modelling software. High ore grades at Vera Nancy are controlled by both the primary geometry of the mineralised structure and the intersections of the main mineralised veins with subordinate splay veins. The main mineralised structure dilated as a consequence of extensional tectonics while the splays acted as conduits bringing oxidising surficial fluids into mixing zones precipitating high gold grades. Near-mine exploration is focussed on identifying zones of vein flexure and splay interaction to locate the relatively small high-grade shoots. Data modelling in a 3D environment is an essential process for understanding the geometry of the system being explored.

Jan 1, 2000

By Lawless JV

Recent exploration for gold on the Pacific Rim has utilised similarities between active hydrothermal systems and epithermal gold deposits. The major control over formation of such deposits is the hydrology of the ore-depositing hydrothermal system, which varies depending upon its geologic setting.

Jan 1, 1987

By F Baars, M Zu, C A. RosiFre, L Lobato

A genetic model for the genesis of high-grade (>65 wt per cent Fe) Proterozoic, banded iron formation (BIF)-related iron deposits such as the Tom Price, Mount Whaleback deposits in the Hamersley Province (Australia), the N4E, N4W, N5 deposits at Carajßs (Brazil), the Aguas Claras, Conceitpo, and Casa de Pedra deposits in the Iron Quadrangle (Brazil), the Donkerpoort West, Kwagas East deposit in the Thabazimbi iron ore district (South Africa), or the Saksagan ore field at Krivoy Rog (Ukraine), needs to take into account the: timing of regional metamorphism with respect to the upgrade of BIF to high-grade iron ore; significance and relationship of the proto-ore to the hydrothermal alteration minerals and zonation and the process of iron enrichment; source and oxidation state of the hydrothermal fluids that caused the iron enrichment; types of geochemical processes that caused the hydrothermal alteration and iron enrichment; and significance of the widespread carbonatisation of the host rocks as a prerequisite for high-grade BIF-related iron mineralisation.We argue that a unifying model for high-grade BIF-related iron deposits cannot, presently, adequately explain the geological and geochemical characteristics observed in these deposits and, therefore, provide two end-member models that take into account the diversity of geological and geochemical ore deposit features. Our discrete model for the genesis of high-grade, BIF-related iron deposits is based on the interpreted tectonic setting, distinct hydrothermal fluid source of, and processes observed in, major BIF-related iron deposits. We divide two end-members: Proterozoic deep fault-magmatic (Carajßs) type, and Proterozoic rift-basin (Hamersley) type.Both end-members experienced varying degrees of deep weathering episodes that effected the hypogene enrichment and, ultimately, yielded the high-grade iron ore mined in many places today.

Jan 1, 2005