Search Documents

By Watson D. F

Armstrong's (1983) criticisms of PhiIip and Watson's (1982b) note on optimal drilling patterns are based on misinterpretation, supported by errors in geometry. Furthermore, Armstrong argues conceptually from the perspective of Matheronian geostatistics, as does also Rudenno (1983a, b). Thus, both authors embrace a global, probabiIistic method of assessing spatial data sets, an approach that must be contrasted strongly with local, deterministic interpolation methods. Some of the important assumptions of geostatistics are outlined and the non-unique nature of the method discussed. A probabilistic approach can be judged appropriate when exploration data are erratic, or known to be unreliable, or when extrapolation is desired. Where data are treated as exact, kriging can give the most biased result if tested against other interpolation methods. We reiterate our previous conclusion that the equilateral triangular grid is approximately 30 per cent more efficient (in terms of numbers of drill holes) compared with a square grid for the same maximum interpolation distance. This is simply due to the improved isotropy of sampling. New, locally-based, deterministic methods for computing ore reserves seem to be required.

Jan 1, 1984

By J E. Wajon

This paper discusses the background, requirements, need and content of plans for management of drinking water self-supplied to mining-related operations, including construction camps, especially in remote areas of Western Australia. The paper discusses the importance of cooperation between regulators, the mine site operator and the consultant in preparing a plan fully compliant with the Australian Drinking Water Guidelines to protect the quality and safety of drinking water supplied to mine sites. The paper outlines some of the issues that need to be addressed in preparing a drinking water quality management plan, such as hazard identification, risk assessment, the multiple-barrier approach and the concept of critical control points. Data requirements, monitoring, incident management, training and reporting are also covered.CITATION:Wajon, J E, 2013. Drinking water quality management for mining operations in Western Australia, in Proceedings Water in Mining 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By R Lloyd

Coal Services (Health and Safety Trust) funded ARRB Transport Research Ltd to investigate fatigue and performance of truck drivers over consecutive shifts. The main questions were to assess: What is the most important contributor to acute fatigue in mining? Is it length of shift (eg eight hours versus 12 hours) or is it time of day (eg circadian effects)? What is the limit of successive day or night shifts before chronic fatigue affects operator performance in open cut mines? The project methodology included utilising ARRB Fatigue Monitoring Devices (forced-choice stimulus reaction) in eight haul trucks, testing 24 subjects over several weeks. Each subject filled in a Fatigue Risk Questionnaire on lifestyle and health. Operators worked a 14-night, one day off, 13-day roster of 12-hour shifts in a fly-in/fly-out operation with excellent opportunities for restorative sleep between shifts. A total of 3500 hours of real-time data was collected, representing the first set of objective, real-time driver performance data for Australian mining. The data showed that for a single night of driving haul trucks, there appears to be no effect on operator fatigue from the amount of time on task (for the 12 hours). In fact performance was worse through the first eight hours than the last four. The circadian influence had a stronger affect than working more than eight hours. Of the 14 nights worked at the site, nights 13, 14, seven and two respectively, were the worst. This presents a conundrum for policy makers who may like to place caps on working hours or rosters in the hope that it will alleviate the fatigue issue. It will not. The major finding within this study is the combined influence of circadian rhythms (human body clock) and individual variability on performance. The lifestyle habits and the health of individuals have a profound effect on operator performance as shown by the strong positive correlation between high fatigue risk scores from the Fatigue Risk Questionnaire and poor performance. An individualistic approach would appear to have the best chance of reducing high potential incidents due to fatigue through successive nightshifts.

Jan 1, 2005

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Taylor, M Smith, A Tunnadine, D Nikolakopoulos

As Olympic Dam rapidly expands into the Southern Mine Area (SMA) the Mine Geology team has concurrently ramped up underground diamond drilling to sustain rates of above 175 km/a. With >10 underground rigs double-shifting, traditional paper sections used for the management of drill programs were no longer optimal due to scale of operations. An opportunity was identified to modernise monitoring of all underground diamond drill programs, through the integration of logged copper sulfide estimates with Olympic Dam’s first-fully integrated deposit-scale geological model in Leapfrog Geo. This paper describes the transition within the Mine Geology team from reliance on 2D paper sections, towards near-real time 3D geological modelling for optimising end-of-hole decisions in the field. This transition was enabled by innovative database solutions informing locally constrained implicit models, limited by a distance buffer around active underground fan drilling. Due to the high volume of historic drilling, there were significant computational challenges with the implementation of daily production style implicit models at Olympic Dam and initial testing of regular updates to implicit gradeshells and sulfide domains required in excess of 12 hrs to run. The enabling solution was to optimise the interfaces between the AcQuire database, Deswik MDM and Leapfrog Geo to create a dynamic, streamlined workflow that was easily completed by Mine Geologists in accordance with daily production duties. Geologists are now building rapid implicit models for a range of variables from an integrated data set of logged sulfide estimates and existing assays, spatially constrained by 150 m buffers around active drilling using a unique drill fan identifier flagged during the planning phase. Once the live-implicit models are updated, they are exported for visualisation on field tablets to be used during logging and core checks at the start and end of every shift. To manage the risk of ‘going digital’ interpretation remains at the forefront of the drill section close-out process, with Mine Geologists critically reviewing the finished sections on a standardised template with new learnings wireframed and communicated to stakeholders. The Live Field Model has enabled a step-change in the geological effectiveness of diamond drilling, reducing over – and under-drilling ore-waste at Olympic Dam continuing to push drilling effectiveness towards 20 per cent of intercepts >2 per cent Cu. In addition, upside or risk identified during the proactive management of drilling execution can be rapidly capitalised or mitigated.

Mar 22, 2022

By S Jeffrey, S Mundell, F Arboleda

In the current cycle of low commodity prices and rising costs, mine managers continue to focus on optimising mine performance and productivity. A critical component of strengthening performance and productivity is ensuring material is routed correctly and efficiently through the core mine production activities of drilling, blasting and grade control.By the time a blast is planned, an enormous amount of intellectual property has been invested in the exploration, resource development, feasibility studies and mine planning activities. The value of that knowledge is either realised or diminished during mine production. Efficient execution of the process is critical and is reflected by the quality and timeliness of the information produced.Multiple teams are involved in the mining extraction process. These teams are all under time pressure to keep the mine equipment operating. One of the root causes of this pressure is the dependency between the teams. They do not operate in isolation, but are a link in a chain depending on the outcomes of each activity. It is essential communication is efficient so tasks can be completed according to the production schedule. Unfortunately, communication fails when unintegrated systems are used because of:- different teams seeing different data, hence there is not an overall, up-to-date view of progress and priorities- lack of cross-functional visibility of data leading to failure to identify errors in time to address or correct issues- teams tending to be siloed and focusing on their part of the process rather than the overall objective.With different systems used for the parts of a common goal, supervisors and managers lack visibility of the process. This makes it difficult to identify process improvement opportunities.Streamlined communications help consolidate all data and activities resulting in improved cooperation between mine production teams. This outcome increases the confidence and efficiency of material routing decisions. It also reduces potential impact to mine performance from errors in early stage tasks like drilling and grade control. Having everyone collaborating off the same trusted data, helps teams identify with common goals and find business improvement opportunities as they appear.CITATION:Arboleda, F, Mundell, S and Jeffrey, S, 2016. Driving mine performance through communication, in Proceedings International Mine Management Conference, pp 117-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By S G. Walters

The minerals industry is facing a productivity and investment crisis. The ‘Millennium Super Cycle’ from 2003–2011 was an unprecedented period of growth and investment resulting in increased throughput and development of lower grade resources to meet demand. During the boom quantity became more important than quality with throughput the key metric. This was accompanied by a general trend of decreasing feed grades across all commodities that was offset with higher production volumes.Current industry perception is that feed grade depletion is an unavoidable consequence of ore deposit geology and mass mining technologies for increasingly mature mining operations. In typical crush-grind-float operations value recovery only takes place at ~1–200 micron particle size during flotation, ie 3–4 orders of magnitude size reduction compared to primary feed. For increasingly low-grade deposits the cost of energy and capital intensity required to process and reject low value material at micron scale drives poor productivity. An alternative is to deploy a range of coarse (~10–100 mm) separation and rejection technologies. Grade Engineering® is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans.Coarse rejection can be used on size distributions ranging from run-of-mine (ROM) to semi-autogenous grinding (SAG) discharge. Grade Engineering® is based on five rock based ‘levers’ linked to combinations of screening, sensor-based sorting and heavy media separation. These involve exploitation of preferential grade deportment to specific size fractions during breakage: differential blasting to condition grade by size at bench scale; sensor based sorting at truck and conveyor scale; and differential particle density.Grade Engineering® is being developed and implemented by a consortium of over 30 mining companies, equipment suppliers and research organisations. Emerging results from collaborative site activities demonstrate potential for generating significant value, which can reverse the trend of declining productivity due to feed grade depletion.CITATION:Walters, S G, 2017. Driving productivity by increasing feed quality through application of innovative Grade Engineering® technologies, in Proceedings Tenth International Mining Geology Conference 2017, pp 263–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

By M McCurd, M Lynch, B H. Yin, S Mendoza, C W. Bumby, Y Iwasaki, B Rumsey

Iron and steel production is responsible for approximately 6.3 per cent of global anthropogenic CO2 emissions. Direct reduction of iron with hydrogen is a potential route for decarbonising the iron and steel industry. Extensive small-scale laboratory experiments have been performed to test the feasibility of hydrogen-direct reduction of iron ores sourced from diverse geographical locations. However, test results from the batch reduction of small-sample do not necessarily translate to continuous commercial-scale processes. Establishing a small-scale continuous test reactor for H2- DRI process is challenging, requiring substantial resources and investment. The limited availability of small-scale reactors that enable testing under relevant conditions has become a major obstacle for H2-DRI development, leaving a big gap between laboratory success and proof of commercial feasibility. Here, we report on the recent commissioning of a continuous counter-flow vertical shaft reactor, which has a processing capacity of 6 kg/hr iron ore pellets at up to 100 NL/min H2 flow. We believe this to currently be the largest H2-DRI facility in the Southern Hemisphere. In this talk, we will discuss the design and construction journey for this reactor, starting from the initial system design to the initial demonstration of H2 reduction of titanomagnetite ironsand pellets. This reactor now enables a range of research capacities, including the validation of laboratory results on a larger scale with practical operational variables, feasibility assessment of hydrogen direct reduction of different iron ores on a commercial scale; identification of scalability, sticking, and other potential issues before building a full-scale plant; and a viable solution for producing small-quantity DRIs for downstream melting investigations. Overall, this new research facility offers significant benefits for assisting the transformation of iron and steel production to a more sustainable and green industry.

Sep 18, 2023

Owing to the 'creeps' and consequent movements in the mines, followed by the recent fire in the southern workings, the whole of the orebody above the 800 ft. level is now very much crushed and broken. The same applies to the hanging wall or overwall coutrny, which has subsided towards the workings, so that for some years past all development work within the lode has had to be carried out with extreme care.The continual but slow subsidence of the overburden into the stopes necessitates a periodical renewal of all gangways in the lode, and, as the subsidence amounts to as much as 60 ft. in places, these new gangways must necessarily pass through the mullock-filling of old stopes in addition to broken ore. They at times pass into the broken ground of the hanging-wall for some distance, where the orebody has widened underneath by the original folding and puckering.

Jan 1, 1932

A model has been developed for drum scrubbing which allows selection of geometry and power input. Specific aspects considered are: Calculation of total static and operating volumes. Total residence time based on total operating volume. Solids residence time based on solids operating volume. Selection of the aspect ratio. Alteration of operating fill to allow for smaller or larger feed openings. Selection of proportion of critical speed. Calculation of shell and motor power requirements. The model uses either solids or total residence time to calculate the required operating volume. The solids residence time is based on the proportion of coarse solids in the feed. Material finer than the reject size is considered as part of the slurry. The solids operating volume is the static volume plus the surcharge on the discharge weir required for flow of the solids from the unit. The total operating volume is the static volume plus the surcharge on the discharge weir for the total flow to exit the scrubber. The burden density is calculated from the coarse solids bulk density and the slurry density that includes all the fine solids. Power is calculated using the Liddell and Moys correlations for burden position and shape, and the operating rotational speed. Results from the model (especially power) have been verified from industrial installations of significant size. Predicted and observed power draws are within two per cent. A check against the JKMRC mill model shows power draw prediction agreement to within four per cent.

Jan 1, 2004

An improved method of sample recovery for use with rotary percussion drilling has been developed. Cuttings can be recovered continuously from either dry or wet drilling, and the recovery under dry conditions is seldom below 99% of the cuttings brought to the surface by the rig. The system is designed for use with top drive drilling rigs using flush-jointed drill rods. The key feature of the system is a self-aligning mechanical seal around the drill rods. The sealing unit is removably fixed to a collar section of cas ing. the cuttings are recovered in a plastic bag attached to the bottom outlet of a cyclone. A valve at the bottom of the cyclone permits the cuttings representing various depths to I,e recovered separately for examination eind 0(iclysis. [u the Iron Monarch quarry, two percussion holes were drilled to depths if 30 metres and 28 metres using the unproved sample recovery system, and diamond drill holes bored 1 metre from each percussion hole. Samples from each hole were sectionalized over metre intervals and analysed for iron, silica, alumina and loss on

Jan 1, 1976

By C S. Kelsey, J R. Kelly

Australia is presently enjoying the fruits of a booming iron ore market. Expectations are that market strength will be supported in the short to medium term by increasing feedstock demands from steel mills, as world economies rebuild post-Covid-19. However, as cost and environmental pressures increase the longer-term market outlook will be dominated by product quality. The ‘flight to quality’ will place increasing demands on direct shipping ore miners as they compete to maintain their standing in the iron ore marketplace. China will progressively disengage from its dependence on Australian imports, leaving miners under increasing pressure to boost product quality and diversify outlets globally. Australia has vast deposits of low-grade magnetite ores located mainly in remote and arid regions of the continent. This paper proposes a dry grinding and magnetic separation process to produce premium concentrate grades from the low-grade ores, to assist in meeting future product quality demands. The premium grade concentrates could be either blended with lower quality direct shipping ores or marketed separately. The proposed dry concentration process involves the pairing of Vertical Roller Milling (VRM), a mature technology widely used in the cement industry, and Planar Magnetic Separation (PMS), a new methodology, which has been developed to the threshold of commercialisation by the private Australian company Cyclomag P/L. Two laboratory prototype planar magnetic separators with field strengths of 1800 gauss and 6000 gauss have been built and tested on a range of magnetite ore types over the past three years. In each case, following grinding to liberation sizes, a combination of roughing and cleaning operations has produced pellet grade concentrates. Vertical roller milling has competed successfully with conventional media milling in grinding cement clinker, limestone and blast furnace slags. A key advantage of dry VRM/PMS processing is its potential adaptability to stepwise modular development, which can minimise initial capital investment, while generating early revenue streams to cope with unpredictable market volatility.

Nov 8, 2021

By P Waters

BHP Billiton Iron Ore initiated a program in January 1995 at the Mt Whaleback operation in Newman, Western Australia to develop a closure plan for the overburden storage areas (OSA), which have the potential to generate acid rock drainage. The primary research program includes the development of technology for the long-term performance of OSAs with respect to slope stability, surface run-off, erosion, water infiltration and vegetation. The objective is to control acid rock drainage by preventing moisture movement into and through the OSA material. Infiltration to the underlying OSA material and closure costs are minimised due to the presence of the run-of-mine (ROM) cover material. A summary of the field data is presented to illustrate low percolation rates to the underlying OSA and key performance characteristics of the moisture store and release cover system design. Field data collected to date demonstrates that a moisture store and release cover system constructed with suitable ROM material has good potential as a final cover system at the Mt Whaleback site. The performance of the cover system on a sloped surface was significantly different as compared to placing the cover system on a horizontal surface.

Jan 1, 2003

**Add abstract here**

Jun 1, 2010

By R J. Nicholson, J M. F Clout

As part of an overall strategy to make significant new technological advances for the sustainability of the mineral processing and related process industries CSIRO Minerals has developed a new dry separation device. It represents a technology breakthrough and has the potential to radically change the way in which dry particle size classification is achieved in the minerals industry. Conventional dry separation techniques have limited applications and often suffer from low productivity, high operating costs, low separation efficiency, the need for dust control and a lack of flexibility. In the absence of efficient dry techniques, wet processing is often used. The use of wet processing either requires the introduction of water into a separation process, which causes environmental concerns through the need for water supply and tailings dams or the use of æunfriendlyÆ chemicals for dense media separations that have considerable impact on handling and disposal. Wet processing also increases operating costs due to plant instability, materials handling, thickening, filtration and product drying. The new CSIRO technology exploits a combination of natural and applied forces to achieve specific particle motions that produce size separation. In doing so, many of the traditional shortcomings of dry separation have been overcome. The CSIRO Dry Particle Size Separator is ideally suited for dry size separation applications within the size range 1 mm to 30 ¦mfor moderate moisture levels (2 per cent), have low unit throughput, produce a fixed cut size and are therefore impractical where very high unit capacity and low operating costs are required. This paper presents a review of dry separation devices together with details of the new Dry Particle Size Separator and typical results for a number of materials, including iron ore and quarry dust.

Jan 1, 2002

When mining of ilmenite deposits wet process of preparation is traditionally used. But this method needs large volume of water. The problem of water deficiency is characteristic of many regions of the Republic of Kazakhstan. The Satpayevskoye ilmenite deposit is situated in the East Kazakhstan, its location has problems with water, and the mineralogical composition of rock is unfavourable: rocks contain up to 40 per cent of clays. That is why designers made a decision to use dry process of preparation for processing of these ores. Offered scheme and equipment selection are presented in this paper.

Jan 1, 2003

By W Skinner, C G. Kelsey, J R. Kelly

The iron ore industry has reached the end of an unprecedented period of expansion triggered by China’s demand for iron ore. Lower ore prices have led producers to focus on optimising mining operations while extracting the maximum tonnage from the infrastructure presently in place or from projects already underway. A rising global surplus is expected to further force ore prices down and lead to output curtailments, which in turn will help to restore market balance. However, investment in the development of new resources and the development of new infrastructure will inevitably become necessary. Making the right decisions in relation to future processing infrastructure in a climate of uncertain demand and price volatility will not be as straightforward as in the past, where expanding the scale of a proposed operation has been the answer to ensuring economic viability. Overall cost and environmental pressures particularly in relation to wet processing will dominate the decision-making process. IMP Technologies (IMPTEC) has anticipated the need for a dry low cost processing alternative, which can open the way for the development of lower grade magnetite deposits and ensure the sustainability of processing in Australia. The lower grade magnetite deposits are generally fine grained and require grinding to p80 of 30 to 40 microns. Historically, the cost of grinding to these sizes has been and remains a key factor determining the economic viability of a magnetite processing operation. The IMPTEC Super-fine Crusher and Cyclomag Separator are the key components of a proposed radically simplified dry processing alternative, which addresses both cost and environmental issues. This paper reports on the results of pilot super-fine crushing and cyclomag separation test work, focused on supporting the feasibility of the proposed dry processing route for the production of high-grade pellet plant feed from fine grained low-grade magnetic ores.CITATION:Kelsey, C G, Kelly, J R and Skinner, W, 2017. Dry processing of magnetic iron ores – addressing cost and environmental issues, in Proceedings Iron Ore 2017, pp 215–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Artone E

screening equipment installed in e Hamersley Iron operation is described, and tails of operating parameters and screening - Iia in use are given. Tests were carried out on full-size reens in the operating plants to study the Meets of mat aperture size, feed size distri 1,ution, feed rate, screen speed and throw, angle of inclination, and feed moisture content n screen performance. Sampling equipment was signed so that undersize samples could be htained from various locations along the length of the screen, thus providing information pout the quantity and size of particles passing òhro gh the screen at any point. Conclusions derived from the testwork and relevance of these to the Hamersley Iron aeration are discussed.

Jan 1, 1984