Search Documents

By Butler RD

The Singhbhum Copper Belt is an arcuate zone of verthrusting which extends over a strike length of about 180 kilometres, located in Eastern India, 150-300 kilometres west of Calcutta. The Belt is noted for its mineralisation, and both copper and uranium are currently being mined within it.

Jan 1, 1990

The ore reserves of the Frieda porphyry copper prospect in Papua New Guinea have been estimated using kriging and an alternative method. Only very erratic variograms could be obtained from the raw data and thus it can be expected that kriging variances will be unrel- iable. The frequency distributions of the two sets of estimates show expected differences and the resulting mineable reserves show similar expected differences. More drilling and the use of disjunctive kriging are needed to produce reliable estim- Ates.

Jan 1, 1979

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By Yates M. G, Rowlands A. T

Most geostatistical techniques applied to the estimation of ore reserves assume relatively unifonn grade and thickness within an ore deposit environment. In shear-hosted mineralisation this rarely occurs. The distribution of mineralisation is controlled by the kinematic and geometric variation within the shear zone. Although the kinematic variation is dependent primarily on the temperature (and consequently the depth) of formation of the deposit, the geometric variation appears to be relatively insensitive to this parameter. Shoot mineralisation is controlled either by the intersection of secoodary shear planes (brittle deformation) or the stretching lineation of the mylonitic fabric (ductile defonnation).Once the shear geometry is clearly identified, it is critical to review the distribution of grade and thickness of mineralisation. The practice of cutting high-grade intersections without reference to the shear model leads to underestimation of the amount of gold in the deposit. High-grade shoots may occur as pipe-shaped bodies within the system; their identification is essential for both resource estimation and mine planning purposes.

Jan 1, 1991

By G Ferguson a, P Carrasco, P P. A Dowd

International codes of practice offer broad definitions with respect to the classification of resources in terms of risk. Specific guidelines and protocols, to analyse sample data, carry out geostatistical appraisals, develop geological models and finally estimate and classify resources, are not addressed. Neither are detailed requirements for engineering mineable reserves from estimated resources. In addition, international codes of practice fail to distinguish between types of deposit, other than in broad terms, as for example, The AusIMM JORC Code (JORC, 1999) which makes reference to diamond and coal deposits. The objective of this paper is therefore to set in motion the process of specifying detailed protocols, acceptable to the international community, for the assessment, reduction and management of risk associated with the development and extraction of mineral deposits. Ordinarily, the main risks and issues encountered during the process of estimating resources and subsequent conversion to reserves, encompass:failure to understand relevant geological controls of mineralisation; validation of grade interpolation; optimism in geotechnical appraisals of dilution and stability and the consequent selection of inappropriate mining methods; metallurgical modelling of minerals and contaminants reporting to concentrates; appraising the hydraulics of heap leaching and the numerous factors that can affect recovery; difficulty of managing metal price cycles and changes in regulations within the constraints of long-term mining plans; and development of better evaluation techniques for mining ventures. Uncertainty is inherent in estimation and engineering work, and its identification, reduction and management should be a fundamental goal of all involved in the mining industry (Figure 1). Variability may be reduced by:following internationally accepted practices for the collection, manipulation and analysis of geoscientific data; and verifying that the procedures actually performed meet the associated standards. Increasing amounts of data will also reduce uncertainty, but only if the procedures used to collect and appraise such data follow the relevant procedures. It is thus the aim of a series of papers in preparation, Beniscelli et al (in prep), to put forward detailed guidelines, for:project sponsors û to provide a global view of the work and documentation needed to support requests for funding various phases of project development and budget approvals; geologists û to indicate a checklist of the requirements and standards for the exploration and estimation of resources; and engineers and economic analysists û the protocols for characterising, modelling, engineering and evaluating the extraction of reserves. It is therefore hoped to encourage the development of consistent standards for declaring reserves within the mining industry. Data from projects and operations will be utilised to illustrate the benefits of adopting a rigorous approach to estimating resources and engineering reserves, Beniscelli et al (in prep).

Jan 1, 2000

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

By J Rostami, T Afshar, M Sharifzadeh

Accurate estimation of rock load and selection of types of ground reinforcement to match post-failure behaviour of rock mass are important issues to assure tunnel stability. This paper focuses on the main factors affecting rock load to evaluate the capabilities of the existing models for prediction of rock load. Rock mass properties, project features and excavation method, as well as ground conditions and stress condition were found to be the key factors affecting the magnitude of rock load. Field data from tunnels of about 37.5?km driven in several geological structures in non-squeezing ground was used in this study. An in depth statistical analysis was performed on data to find correlations between the input parameters and measured/observed rock load. A weighting system was proposed to obtain the proper contribution of each factor for estimation of rock load in tunnelling through various ground conditions. The new classification system offered predicted values for rock load that were in a good agreement with the actual field measurements. The high disturbance factor (D>0.4) was the prime factor which controlled the rock load. Rock mass quality was the second key factor influencing rock load, which could be estimated by GSI, GSIresidual , especially when combined with tunnel depth.CITATION:Afshar, T, Sharifzadeh, M and Rostami, J, 2014. Estimation of rock load for tunnels with different disturbance factors, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The sampling of a run-of-mine (ROM) ore with the objective of controlling the fundamental variance associated with the sampling step is a poorly understood subject. Finding the effective sampling constant by repetitive sampling to establish the variance between nominally identical subsamples of a given mass of the ore is a laborious, time-consuming and very expensive exercise. In this paper, the run-of-mine ore is modelled using three components: ore, waste, and relatively fine material which shows significant liberation of the mineral phase(s) carrying the target analyte. The expression for the sampling constant of the mixture is developed from first principles. The form of the equation provides insight into the factors that are important in controlling the magnitude of the sampling constant and hence the fundamental uncertainty associated with a given mass of sample. The controlling factors are shown to be the size distribution of the ore/waste mixture, the proportion of waste mixed with the ore and the extent of liberation and the size distribution of the liberated material in the finer fractions.

Jan 1, 2008

THE object that the writer has mainly in view in presenting this paper is to draw the attention of those connected with the technical side of the industry to the unsatisfactory and by no means up-to-date methods employed in estimating the tin contents of an ore. At the same time, what is regarded, from the writer's personal experience, as a satisfactory and reliable method is explained in detail. It is a curious fact that for the last 25 years tin·assay methods have made little or no advance, while those now in general use ill connection with copper and lead ores can scarcely be compared with those then obtaining, so greatly have they been improved upon. Though it. is not altogether expected that the method herein advocated will at once meet with general approval, the writer hopes the resultant discussion may bring out points that have hitherto escaped detection.FIRE METHODSThe old Cornish method of smelting with anthracite is now obsolete. The cyanide assay, although unreliable, is still much used because of its simplicity. In the Malaya many buyers of tin ores use the cyanide assay, the smelting being carried out generally in a benzine furnace. It is essential that the smelting with cyanide be performed at a low temperature. Even then, impurities, such as Sb2S3 and...

Jan 1, 1912

Maps of mineral grade used to assess mineral reserves are most commonly generated using one of the many estimation methods available such as inverse distance weighting or ordinary kriging. Most such maps incorporate a degree of spatial smoothing which is an integral part of the averaging process. In deposits with highly variable grade which include many gold deposits, this smoothing can mask the detailed geometry of the mineralization at the economic cutoff grades being considered. In underground mining, a knowledge of this geometry is important in the choice of mining method and thus in the assessment of the minable reserves.The method of conditional simulation in geostatistics can be used to generate maps of grade which reflect the actual spatial variability of grade as measured through the variograms of the drill hole data. Simulated maps can provide a number of equiprobable images of the mineralization geometry from which a more appropriate mining model of the mineralization can be developed. Multiple simulations can also be used to assess the uncertainty existing in the current knowledge of the reserves.

Jan 1, 1990

By L Brodie-Hally

In the early-1990s, Tad Golosinski, the former the head of mining department at WASM participated in a review mining engineering courses in Australia. The review team asked various industry executives what subjects they thought graduates needed to be taught. Tad made the comment to me that the more senior executives thought that history and ethics were very important. The outcome was that the mining engineering courses were required to contain at least five per cent content dealing in ethics. The course was to be modified to reflect this. Tad thought at the time the students would think that subjects dealing in history and ethics came from retirees and professionals that were over the hill. So let me talk to you today about ethics.

Jan 1, 2002

By M Donatelli, E Grazio, A Heissenberger

The distribution of a contaminant in a bulk mass greatly influences the effectiveness of sampling procedures. Most currently used sampling guidelines for genetically modified organisms (GMO) testing have stringent distribution requirements. Specifically, all these protocols are based upon the assumption that GM material, if present, is randomly distributed. Yet, assuming randomness is risky because the applied sampling plan may not provide an accurate estimate of the content of the contaminant. Despite the general consensus that an evaluation of the possibility of non-random distribution of GM materials within lots is a pre-requisite for the definition of effective sampling protocols, no experimental data on the distribution of GMOs in kernel lots are available anywhere in the world. Additionally, to date there is no distribution-free statistical model to estimate sampling errors, thus making the theoretical definition of optimal sampling technique impossible when randomness cannot be assumed. Here we present preliminary results of the KeLDA project, which is the first study investigating the distribution of GM materials in large soybean lots imported within the European Union. The extensive variability of GM content, observable both within and among soybean lots, indicates that heterogeneity issues cannot be overlooked when defining sampling strategies for large lots of particulate material and that randomness cannot be assumed a priori. A new statistical model free from any distribution assumptions, developed in order to estimate the sampling error associated with different sampling protocols together with the risk of false-negative results, is also presented. The new model, which is applicable to any consignment of particulate material with respect to any kind of contamination, presents two novelties: first, freedom from any distribution assumption; second, the possibility of estimating the magnitude of the sampling error associated with different sampling protocols as a function of specific distributional properties.

Jan 1, 2005

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best ægrade descriptorÆ is discussed.

Jan 1, 2007

Knelson concentrators are commonly used to recover fine liberated gold in gold processing plants. The decision to employ a gravity gold circuit consisting of centrifugal devices such as Knelsons is primarily taken on the results of GRG tests, among other considerations. While the GRG test is considered a material characterisation test, which is useful in the design stages, its use in evaluating the performance of an existing unit is questionable. The problem is exacerbated by the fact that it is time consuming and costly. This paper examines the validity of the GRG test for performance evaluation and discusses alternative test work that can be performed to evaluate the performance characteristics of an operating machine. Principles that are useful in selecting optimal operating parameters, such as optimal fluidising water flow rate for a given ore/machine combination, are also discussed and illustrated with laboratory and plant data.

Jan 1, 2007

The paper first outlines the conceptual basis for evaluating and controlling geological risk. Geological risk, the economic reflection of the uncertainties associated with tonnage, grade, and other pertinent deposit parameters, is evaluated in terms of economic risk criteria. Delineation provides the deposit information required to appraise and control this risk. The improved reliability of geological estimates resulting from additional delineation reduces the economic risk associated with mine development and production decisions. However, the benefits of delineation, subject to diminishing returns, have to be weighed up against the direct and time costs involved. These costs decrease base case economic values and shift the probability distributions of possible outcomes towards, lower values. The optimum amount of delineation normally is achieved short of the point where economic risk is minimised, depending on the mining company's relative preference for a higher base case value or a lower economic risk. Then, two open pit copper mine examples, based on actual situations, are analysed to illustrate the application of the concepts presented. The first case concerns the extension of ore reserves at an operating mine. Finally, a new mine development opportunity is considered.

Jan 1, 1994

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By N J. Arunakumaren

A coal mine is proposed for an area where a major river traverses the project area. There were initial concerns that inflow of groundwater from exposures of high permeability alluvium associated with the river system could pose mine dewatering problems together with adverse impacts on surface water resources in the river. The project included collation and analysis of geological and hydrogeological data collected historically over a long period of project investigation and evaluation. The project also included establishment of additional groundwater monitoring points to provide a reliable groundwater contours. The groundwater level contours were produced to allow numerical models to be calibrated to support estimation of groundwater inflow. River bed cross sections were also prepared to assist study of the effect of river flow on the inflow. Two separate MODFLOW groundwater models were produced to simulate long-term groundwater inflow to the mine with an upper model consisting of the Quaternary and Tertiary alluvium lumped together and a lower, separate model consisting of Mesozoic coal measures. Analytical solutions were used to predict initial inflow from the alluvium and from the coal measures.

Jan 1, 2003

By I Govender, T L. Moodley

Tumbling mills are grossly inefficient, using only 5 per cent of the total energy supplied for actual breakage. A significant proportion of this inefficiency is unavoidable owing to geometric limitations; rotating drum systems are prone to exhibiting certain regions (energy barriers) that resist particle entry thereby restricting the transfer of energy. Though such systems are inherently inefficient, improved modelling schemes may lead to slightly enhanced efficiency through better microscale predictions of key breakage drivers (stress, force). Central to achieving such incremental advances is the development of a universally accepted rheology for dense granular flows. Armed with a better understanding of these macro-scale ingredients, classical process modelling offers an efficient, spreadsheet friendly framework for recovering the spatial distributions of the comminution drivers. At this real-time level of process control, it should be possible to tune comminution operations towards more energy efficient configurations – the ultimate goal of this research. The present work employs validated DEM data to recover the full continuum field which will ultimately serve as a basis for calibrating process model outputs based on different rheological hypotheses. Such a continuumbased approach captures tensor properties like the shear stress and strain rate – both of which are necessary to developing a dense granular rheology. Moreover, DEM captures this data at the momentum transfer timescale of 10-6 s – no other measurement technique is capable of this level of spatial and temporal resolution. Importantly, the confidence in this DEM data is strengthened because it has been validated at the continuum scale using Positron Emission Particle Tracking (PEPT) kinematic measurements. Validated DEM data is derived from batch experiments conducted within a 300 mm ID laboratory drum using three and five millimetre glass beads at 60 and 75 percent critical speed; such mill speeds are typically encountered in the tumbling mill industry. Dimensional analysis is conducted using critical rheological parameters (shear rate, shear stress, granular temperature etc), which are key to not only developing a granular rheology but ultimately will be used to tune our mechanistic models.

Aug 24, 2022

By J Seccatore, F Golin, E Munaretti, M Cardu, J C. Koppe, J Bettencourt

Contour blasting is commonly performed by employing linear charges decoupled from the boreholes. This method is common in surface and underground excavations, either for civil or mining purposes. To achieve the best results in terms of rock breakage and respect of the excavation profile, blasting theory suggests that charges should be inserted coaxial to the holes to grant uniform distribution of the explosive energy, therefore obtaining a uniform radius of damage. Nonetheless, due to readiness of operations or lack of availability of specific products on the market, non-coaxial charges are often employed in blasting practice. Non-coaxial charging methods include the employ of high-power detonating cord (40 to 100 g/m), low-power detonating cord connecting small-diameter cartridges (commonly 10 g/m detonating cord priming 1” cartridges) or string loading (a thin layer of bulk emulsion pumped with controlled flow and controlled extraction of the injecting rod). This research focuses on evaluating the effects of the first two charging methods on the quality of final walls in open pit and underground operations. Different drilling geometries and charging configurations were applied to both quarrying and tunnelling blasts. The half-cast factor, the overbreak and the underbreak were evaluated as control indicators. Rock quality designation and rock mass rating were used to classify the rock mass. The research was aimed to push contour blasts to their limits, observing for which geometry and charge configuration the blast lost its design threshold with respect to the final wall for every given rock mass. Results show the operational limits of non-coaxial charges encountered in the rock masses object of this study. In good-quality rock, smooth blasting with decoupled linear charge of 40 g/m can be extended to a spacing S = 22Øf with little or no detectable drawbacks in terms of final wall quality, in contrast with theoretical formulae for the determination of the radius of damage. On the other hand, when the rock is poor, any quality of the final wall is hardly achieved at all, in spite of any care in the details of execution of smooth blasting. It is concluded that any design criterion and theoretical approach modelling the effects of contour blasting cannot ignore the features of the rock mass.CITATION:Seccatore, J, Golin, F, Cardu, M, Munaretti, E, Bettencourt, J and Koppe, J C, 2015. Evaluating the effects of non-coaxial charges for contour blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 267–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H Parra, D Zenteno

Fragmentation modelling has been in use in the mining industry for a long time; however, there are still some aspects to tackle with regard to its use for strategic/planning and day-to-day purposes.On one hand, an important amount of resources are allocated to the task of calibrating and validating a good fragmentation model. Nonetheless, errors during the implementation stage introduce uncertainty into the prediction.On the other hand, it is common practice in the mining industry to use only discrete values to represent the fragmentation from blasting (k20, k50, k80), which provides a biased interpretation of the situation as, for instance, the best and worst possible cases are not taken into account. This is particularly critical when a continuous improvement philosophy has been adopted and modelling is used to either modify the drilling and blasting designs or plan ahead.It is well known that every site has particular conditions (rock mass, equipment, drilling and loading practices, among others) that often define unique trends in implementation. These trends can be captured using statistic and probabilistic techniques and then used as proxies for further analysis.This paper explores the potential of including implementation data in the form of probabilistic distributions into the Swebrec model to improve the performance of this engineering tool during the decision-making process.The fragmentation results of four designs were modelled using three different degrees of accuracy in the implementation for the burden, spacing and explosive column length.The data analysis showed that the probabilistic approach helps to achieve a broader perspective regarding the fragmentation that it is possible to obtain and the implications for the subsequent processes. The analysis also showed that the likelihood of producing similar fragmentation with different designs (involving different powder factors and costs associated) increases with the variability of the implementation.CITATION:Parra, H and Zenteno, D, 2015. Evaluating the inclusion of the implementation variability into fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015