Search Documents

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

ignitions caused by cutting tools have occurred at a rate of some 14 per year in UK coal mines since 1965, mostly on the coalface. The rate has held steady despite reducing output and number of collieries. Investigations were carried out over this period into factors affecting both the concentration of firedamp in the cutting zone and the igniting source. A study into detecting and suppressing ignitions on shearers has been undertaken and it is feasible to prevent certain ignitions from spreading outside the cutting zone. Practical measures have been adopted by British Coal to identify frictional ignition sites and to lay down working procedures to minimise risk.

Jan 1, 1988

By H J. Dalstra

High-grade iron ore may be derived from banded iron formation (BIF) through four fundamentally different processes:1. syngenetic precipitation of chert free BIF,2. residual enrichment by removal of gangue minerals from BIF to form bedded (residual) ironore,3. mechanical erosion of iron oxide and chert from bedded iron ore or BIF and re-deposition andupgrading as detrital iron ore, and4. chemical removal of iron from BIF and precipitation elsewhere as a secondary (channel) irondeposit.Finally, the BIF itself may constitute iron ore if a high-grade concentrate utilised for pellets or sinters can be derived from it through mechanical (industrial) separation of iron oxide by means of crushing/milling and mineral separation.Historically, exploration for high-grade BIF hosted iron ores was focused on the residual (bedded) deposits and driven by supergene concepts. Exploration for detrital and channel type iron ores was mostly secondary to exploration for bedded deposits, but recently, a more focused exploration effort has led to the discovery of enormous moderate to low iron grade deposits in the Pilbara region of Western Australia. Exploration for high-grade iron ores using syngenetic concepts has been limited,but together with exploration using hypogene concepts offers the best hope of fi nding concealed deposits. Exploration for BIF sources suitable for concentrate ores commenced in the ‘old’ iron ore provinces after the high-grade resources were depleted and has only recently gained importance in Australian BIF provinces, mainly as a result of high iron ore prices in the last decade.

Jul 11, 2011

In the past few years the Rietveld method emerged as a routine tool for quantitative phase analysis (QPA) from X-ray diffraction data. Fast and reliable results became possible by combining modern computer technology and optimised mathematical algorithms with the fundamental parameters approach in the Bruker AXS TOPAS software. Here the routine analysis of bauxite raw material and of aluminium bath electrolyte is presented. The accuracy of bauxite quantification was tested by analysing the IUCr round robin sample. An agreement of better than one per cent was obtained for minor constituents and a maximum deviation of 2.5 per cent for the major phases. This is excellent agreement with expected results from weighting. Ten different phases were quantified in natural samples from Turkey with a precision better 0.5 per cent for the major phases and one per cent for the minor phases. Additionally, crystallite sizes were obtained from the peak profiles that give valuable information for the processability of the material. XRD data from solidified aluminium electrolytes were rapidly measured using silicon strip detector technology. With the LynxEyeTM detector full patterns were collected in 90 seconds and analysed with TOPAS. It is shown how to derive well-established measures such as bath ratio and excess AlF3 from the Rietveld results. These measures are widely used in aluminium production and readily available with very high precision. The excellent agreement with ALCAN reference data demonstrates the outstanding accuracy of the method. The mean deviation between here presented results and reference data is below 0.5 per cent for total CaF2, below 0.25 per cent for excess AlF3 and 0.02 for the bath ratio. The precision of the method was evaluated by repeated measurements.

Jan 1, 2008

By B Young

Variable bench heights, interaction with underground workings and a steeply dipping orebody are challenges faced daily by geologists at Xstrata Zinc’s Black Star Open Cut (BSOC) Zinc/Lead/Silver mine in Mount Isa, Queensland.BSOC has been in operation since late 2004 and was developed to extract the surface extents of the Zn/Pb/Ag mineralisation mined in the underground lead mine. To date many large scale stopes and extensive development drives have been intersected and successfully mined. The stratigraphically hosted orebodies strike in a north-north westerly direction, dipping ~75° west. Ore production from the pit is currently at 4.5 Mt/a.Historically, sampling was conducted using a multiple spear technique from blasthole cuttings. This method proved to be relatively reliable when blasting benches at a consistent height, but a requirement to vary bench heights to safely collapse and then mine through underground workings reduced sample representivity to unacceptable levels.The purchase and commissioning of a production rig which had been converted for reverse circulation (RC) has allowed for the flexibility of a small rig, with the capacity to easily drill 48 m holes while ensuring sample quality. Sample quality is not the only benefit of introducing RC grade control. By collecting grade control data well in advance, informed decisions can be made by planning, drill and blast and mining departments weeks beforehand, rather than hours before firing. Additionally, seeking operational value to offset higher drilling costs has proved positive with benefits including increased confidence in orebody wireframes, accurate tonnage and grade for proceeding five benches along with the ability to representatively test metallurgical response on a tight grid spacing.

Aug 22, 2011

By D Jones

The development, piloting and engineering design of an innovative water treatment system for process water produced by a uranium mine mill are described. The process incorporates lime/carbonate softening (Stage 1), reverse osmosis (Stage 2) and biopolishing (Stage 3) to produce water of quality suitable for release to the receiving environment. Comprehensive performance data are presented for each stage. The unique features of the proposed process are: recycle of the lime/CO2 softening sludge to the uranium mill as a neutralant; potential use of power station off-gas for carbonation; and the potential recovery and recycle of ammonia from the RO reject stream.

Jan 1, 2003

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

By Horowitz F. G, Lamb P

As mining operations become larger and more complex, larger volumes of geological, geophysical, and production data must be manipulated and interpreted on a day-to-day basis. Because of the large volume of data, more sophisticated data storage strategies, interpretation tools, and visualisation tools must be used by exploration and mining operations in order to remain competitive. Critical to better practice is an understanding of the basic syntax and character of geological and mining data, expressed in the form of a data model. In the short-term, a data model can be used to implement or evaluate schemes for data storage or exchange. It can be used to evaluate software. In the longer term, a data model is essential to the design of the next generation of software for 3D geological modelling. In this and the related paper (Lin et al, 1995) the data model in use by CSIRO is presented, together with: 1. examples of the use of data transfer in the linkage of existing mining software; and 2. examples of the use of the data model in software design.

Jan 1, 1995

By Landy D. M, Ward M. O, Power W. L

Geological structures are irregular and intricate, so creating a 31) solid geology model is a complicated process. A software system can only partially automate this process, since geological knowledge and experience are required. Therefore, the interaction of a geologist is critical for such a system. This paper discusses some useful advanced functions for enhancing the visualisation and manipulation of 3D solid geology models: flexible attribute display, multiple views, auxiliary display objects, and geologically sensitive operations. It also describes some experiments to explore the effectiveness of these functions and presents sample output. Most existing 3D solid geology modelling systems are implemented in an ad hoc way, which greatly reduces their reusability and extensibility. This paper presents a generic framework for 3D solid geology modelling systems, which is based on object-oriented technology. The deficiencies of current systems may be improved by using this generic framework. A modelling process based on drillhole data is discusses as a case study.

Jan 1, 1995

By F F. Pitard

Observation from attending many conferences around the world reveals that many people are constantly shifting from the word ‘error’ to the word ‘uncertainty’ without a clear vision of what the subtle difference is. The same applies to a large swath of the scientific literature, in which these two concepts are unfortunately often used synonymously, which is a scientific flaw of the first order. In practice, as demonstrated in the Theory of Sampling (TOS), there are both sampling errors and sampling uncertainties. Sampling errors can easily be preventively minimised, while sampling uncertainty for a preselected sampling protocol is inevitable. P M Gy’s work, supported by G Matheron’s critical reviews, demonstrates beyond any possible doubt that sampling uncertainty cannot be achieved if sampling errors are not preventively minimised by applying very stringent rules that are too often ignored by sampling practitioners. A clarification, in line with the TOS, is presented to mitigate the confusion created by circles favouring the use of uncertainty versus the use of the word error. Both words are very different in nature and scope and they are both necessary in their due place and time.CITATION:Pitard, F F, 2017. From errors to uncertainty – a clarification for proper use by the Theory of Sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 355–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The green field site is one that has no history of mining and as such it presents the designer with a blank canvas, on which any number of drill and blasting options can be drafted. No matter which mining method is selected all technology and experience will need to be acquired from outside sources, applied quickly and produce the right results. North Limited, in joint venture with the Sumitomo Group (20 per cent), have developed AustraliaÆs first block cave mine at Northparkes in New South Wales, Australia. This innovative and large scale mining project was taken from a green field site in November 1993 to a fully commissioned block cave mine in December 1997. NorthparkesÆ Endeavour 26 mine is now producing at a rate of 3.9Mt per annum from a 27Mt ore block. Prior to 1993 no history of mining activity existed at Northparkes. The rock had never been blasted and many questions were raised about how it would behave. While it was clear that the Endeavour 26 (E26) orebody contained geotechnical properties appropriate to block caving, the blasting methods required to establish a block cave mine had never been used in Australia and no designs were available. The joint venture partners had no prior experience with block caving and it was immediately apparent that this blasting technology would have to be acquired from foreign sources and applied to the unique local conditions. Conceptual designs for the block cave drill and blast were first drafted in 1994, first issued for drilling in December 1995 and first blasted in January 1996. 470 km of drill metres and four million tonnes of rock were blasted to complete the undercutting project by September 1997. This paper will provide those developing new drill and blast projects with an inside view of how one small technical team solved many design challenges to successfully construct AustraliaÆs first block cave mine under strict quality controls and ambitious time constraints.

Jan 1, 1998

By J Zeni

In 2001, the Springvale Coal Mine determined a requirement for a 360 m deep vertical airway to ventilate ongoing underground longwall mining operations. The project, referred to as the Springvale No 3 Ventilation Shaft, was completed in 2003 - 2004 by blind boring a 4.25 m diameter hole from the surface to the coal seam at 360 m depth. The shaft was completed with a 3.5 m inside diameter lining made from a continuous watertight steel and concrete composite pipe. Presented from both the clientÆs and the contractorÆs perspective, the following paper describes the process of constructing a blind bored ventilation shaft for this application. Beginning with the clientÆs definition of the requirements and specifications for the shaft, the paper describes the steps followed by Springvale Coal prior to awarding the contract. Springv aleÆs process involved a thorough site investigation including procurement of geotechnical data for prospective contractors and the management of issues relating to safety, quality and the environment. The clientÆs view is followed by a description of the planning and works performed by their nominated shaft drilling contractor, Ardent Underground Pty Ltd.The contractorÆs description of the works includes the details of the blind shaft drilling and lining construction process used for this application. The design of the shaft lining installed at Springvale Coal was the first of its type to be used in Australia. The successful installation of a watertight composite shaft lining and the safety of the method, which did not require any personnel to enter the shaft or the mine, were among the positive outcomes from the project.

Jan 1, 2005

By K Barns, H Law, T Whebell, P Scobie, T Perkins, J Siliezar, M Larson

With processing a variety of orebodies at Glencore’s Ernest Henry Mining (EHM) has come a changing mineralogy and more complex requirements for treatment in the concentrator. From mid-2013 and into 2014 the grind size required to achieve sufficient mineral liberation for production of a quality concentrate has reduced significantly. What was once a final P80 of 35–45 microns was forced to 20 microns. This has necessitated some creative changes to the flow sheet that previously had a 937?kW Vertimill regrinding a rougher concentrate to 40 microns. EHM is able to utilise an existing M10 000 3 MW IsaMill previously used for magnetite processing, to provide a quick convenient solution without large scale capital expenditures. Operating the Vertimill and IsaMill in parallel in closed circuit was successful at reducing the P80 of the regrind circuit to below 20 microns which increased the final concentrate grade by four per cent. This circuit and intermediate circuits used are discussed. Performance of the Vertimill and IsaMill is compared for efficiency optimisation to improve the overall circuit performance.CITATION:Siliezar, J, Whebell, T, Perkins, T, Law, H, Scobie, P, Larson, M and Barns, K, 2014. From magnetite to chalcopyrite – a story of versatility and efficiency at Glencore’s Ernest Henry mining?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By I Thomson, L D. Black, R G. Boutilier

The social license to operate (SLO) began as a metaphor for the ability of communities to stop mining projects. Soon people began to speak of levels of social license and the ability of communities to raise costs without completely stopping exploration or mining activities. Today the concept has spread to other industries and is evolving towards becoming a general management perspective on the socio-political rights and responsibilities of the corporation. The business case underpinning the SLO perspective on management is the need to assess and manage socio-political risk. For mining companies, socio-political risk has been steadily rising for several reasons, including the efforts of non-government organisations (NGOs) to pre-empt government policy options; the entry of mining companies into jurisdictions weak in the rule of law; and the weakness of global economic and financial regulation. In this perilous world beyond the comfort zone of effective government, mining companies must build their own socio-political stability by engaging directly with stakeholders to develop a strong SLO. In order to become a practical management perspective, the SLO needs to be measurable, which amounts to measuring the socio-political risks and opportunities presented by stakeholders. We present the results of efforts since 2009 to develop a globally reliable and valid measurement tool at the project and industry levels, validated in studies in Australia, Bolivia, Mexico and the USA. A factor analysis suggested four factors that mine management can address to raise their SLO level. The most chronically neglected factor involves the political right of the corporation to foster more equitable social contracts locally and regionally in both developed and developing countries. We conclude with recommended steps to earn and maintain the social license at the project and industry levels.CITATION:Boutilier, R G, Black, L D and Thomson, I, 2012. From metaphor to management tool - How the social license to operate can stabilise the socio-political environment for business, in Proceedings International Mine Management 2012, pp 227-238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By S M. Jowitt, G M. Mudd

"The mining industry is the source for the vast majority of the metal, mineral and energy resources we use on a daily basis. New deposits are discovered over time and are developed into mines before being rehabilitated – a sequence that when repeated can help contribute to the noble notion of ‘sustainable development’, despite the generic concept of mining being the unsustainable consumption of non-renewable resources. The scale of the modern mining industry is immense – from iron ore and coal to base and precious metals, modern mines are sometimes hundreds or thousands of times bigger than their long lost historic ancestors. We also live in a world with emerging and increasing demands for so-called technology metals (aka ‘critical’, ‘e-tech’ or ‘specialty’ metals) that are needed to feed the rapid growth in renewable energy (especially solar photovoltaic panels and wind turbines), consumer electronics, sophisticated military technologies and super alloys, amongst other uses. These elements include the rare earth elements, indium, germanium, tellurium, rhenium, selenium, gallium and many others, most of which had few or no known uses in the recent past. Although the mining industry has been successful in developing ever larger mines and increasing the scale of production, the key issues underlying the future of the industry are declining ore grades, increased tailings and waste rock generation, the presence of toxic or other impurities, balancing the economics of primary and secondary products, stricter environmental conditions, more difficult exploration, increasing community expectations, as well as the processing of more complex or refractory ores, let alone the recent volatility in world commodity markets. Here, we synthesise our recent research on many of these various issues, focusing on the need to link all areas within the mining chain from mineral resources through mining to environmental performance in order to ensure we obtain the most out of our modern mining effort. The paper presents a unique and detailed assessment of the sustainability challenges and opportunities facing modern mining – and geometallurgical thinking is at the heart of this conundrum.CITATION:Mudd, G M, Jowitt, S M, 2016. From Mineral Resources to Sustainable Mining – the Key Trends to Unlock the Holy Grail?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 37–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Mineral sands are being used as the source material for new "high-tech" engineering materials. One such material, Magnesia Partially Stabilized Zirconia (PSZ) has been developed and patented world-wide by CSIRO. Derived from zircon sands, the material is currently produced by Nilcra Ceramics in Australia and is exported world-wide.The properties of the material are contrary to those generally accepted for ceramics and are far more akin to those of steel. The material resists not only abrasive wear, impact and thermal shock, but does so under corrosive conditions that frequently cause early failure of metal and cemented carbide.While the consumption of mineral sands for the production of PSZ is not going to significantly increase the demand in the short term, the material itself may well assist the productivity and processing problems within the industry.

Jan 1, 1986

By D I. Cliff, K Johnstone, N LaBranche

The resurgence of silicosis and coal worker’s pneumoconiosis (CWP) in mining and the recent ban of engineered stone products underscore the need to comprehensively address mineral dust exposures and the associated health hazards. Worker exposure to particulate matter, remains a pressing concern demanding nuanced exploration as all dusts are not created equal. The established link between silica and respiratory diseases necessitates a more detailed understanding of the characterisation of particulates and their health impacts. While current monitoring relies on total mass, it is increasingly evident that the size, shape, mineralogy and agglomeration of particles play a crucial role in determining health impacts. This has been evident in the engineered stone industry with workers not only facing a greater risk of silicosis, but also seeing a faster progression of the disease and a higher likelihood of dying from it. Simultaneously, the surging demand for critical minerals, integral to low-carbon economies, has seen government and industry fast tracking the exploration, mining and processing of these commodities. Critical minerals, crucial in technologies like lithium-ion batteries and high-performance alloys, are central to achieving global environmental goals. Significant funding is currently being allocated to advance the development and processing of these materials, however there remains a considerable gap in understanding potential health risks, urging comprehensive health risk assessments. To tackle these challenges, the University of Queensland has developed innovative dust characterisation methodologies, including the use of the Mineral Liberation Analyser (MLA), a scanning electron microscope, to characterise respirable and inhalable dust samples. This advanced technique, initially applied in coal and metals mining, is expanding to critical minerals mining, unravelling diverse mineralogical components and particle size distributions. This conference presentation will showcase the latest research, emphasising the use of advanced analytical techniques to deepen our understanding of the size, shape and mineralogical composition of particulate matter. By synergising insights from coalmines, metals mines, smelters, engineered stone and critical minerals assessments, we aim to proactively manage health risks, contributing to safer workplaces and responsible production practices in the mining sector.

Apr 16, 2024

By D A. Kepert, I J. Tehnas, M A. Pudovsk

BHP Billiton (BHPB) was the first company to start iron ore mining in the Pilbara at Mt Goldsworthy in 1966 through Goldsworthy Mining Limited (GML - then Consolidated Goldfields Australia, Cyprus Mines and Utah). Operations later started at Newman on Mt Whaleback in 1969 with the Mt Newman Mining Joint Venture (MNM û then comprising American Metals Climax û AMAX, Colonial Sugar Refineries û CSR and BHP). In 1986 it acquired majority ownership of MNM, and at the same time the previously 100 per cent BHPB owned but undeveloped Yandi property came on board. Purchase of Jimblebar (formerly McCameyÆs Monster) occurred in 1990 and full ownership of Goldsworthy followed in 1991. With the exception of Jimblebar (100 per cent owned), all mines are now 85 per cent BHPB and the balance with Itochu and Mitsui. This evolution of the company resulted in an eclectic mix of mines/ores, each with their varied exploration and evaluation histories. Discussion of some aspects of these histories, and reflections on changes in exploration-related activities with particular reference to discussion of advances in geological understanding since the 1960s forms the basis of this paper. BHPB presently has open cut mines at four main centres û Newman, Jimblebar, Marillana Creek (Yandi) and Yarrie û and is currently developing the former GML Area C near Yandi. With the exception of NewmanÆs Mt Whaleback mine and immediate satellites, all are contract operated. Ore is carried on BHPB railroads (696 km total) for export through the companyÆs Nelson Point or Finucane Island shipping facilities at Port Hedland. Some is directed to the BHPB Boodarie Iron hot briquetted iron plant near Finucane Island. Over 73 Mt of ore was produced by BHPB in calendar 2001, and the company has now mined over 1500 Mt in Western Australia since their operations at Yampi Sound first started in 1956.

Jan 1, 2002