Search Documents

With the sinking of the new No. 3 Shaft and the increasing depth and northward movement of the mining operations, improved ventilation of the mine workings became necessary and it was decided to sink a new upcast ventilation shaft midway between No. 2 Shaft and No. 3 Shaft.The shaft is finished to 16 ft. internal diameter and connects with the mine workings at the 2,600-ft. level. It is lined with unreinforced Concrete approximately 12 in. thick. The shaft sinking routine was drilling, blasting and mucking by hand using a 27-cub. ft. capacity bucket. The concrete lining was poured in conjunction with the sinking and was normally finished within 30 to 50 ft. of the shaft bottom.

Jan 1, 1957

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0·5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

Much of the coal and gold mining industry of New Zealand is small scale. Funding is tight and mechanisation limited. The country has many well documented small coalfields (some with significant outcropping) and alluvial gold deposits. These are generally remote, difficult to access (physically and otherwise) and of submarginal value (largely a consequence of size when viewed for extraction by traditional techniques). The industry is also burdened by environmental and bureaucratic constraints. The above over simplified setting suggests to the Author, a newcomer to New Zealand, the opportunity to consider some novel concepts based on technology and techniques developed overseas or borrowed from other industry sectors. The objective being to make viable in economic and environmental terms projects that might otherwise be stillborn if considered for exploitation by conventional means. The paper mainly discusses 2 concepts focusing on the application of augers for exposed high wall or outcrop coal and micro-tunnelling augers for alluvial gold extraction. These may be considered high mobility 'container' (as in shipping container) packaged, or 'non invasive' mining systems. It is stressed that these are but concepts and have yet to be subjected to rigorous financial or engineering scrutiny. This could only follow their acceptance by, and input from, New Zealand miners. There will also be brief mention of a new modular conveyor system which might have application within the concepts or existing small scale mineral extraction operations and mention of a project currently in progress to apply tangible 'sustainability' to underground coal mining.

Jan 1, 1996

Mineral ownership determination is not always straight forward as in many cases the relevant details are not recorded on the latest Land Transfer title held in the local Land Registry Office. To determine mineral ownership can be difficult, time consuming and expensive especially in a confused sector. Non statute minerals can be owned by the Crown, Land Owner or other persons. Statute minerals (Gold, Silver, Petroleum, Uranium) are always owned by the Crown and thus present no problems. In simple terms the only accurate and reliable method of determining the mineral ownership under subject land is to historically search back to the first registration when the land and minerals were definitely intact. Then carefully ascertain from the evidence gathered along the way to the present day whether any legislation or private agreement altered or affected the status quo.

Jan 1, 1998

By R A. Pax

Heavy machinery such as AG and SAG mills generate a significant amount of noise due to the processes that are occurring inside them. From an environmental perspective, the level of noise generated is a significant occupational safety hazard. However from a technical perspective the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of the primary comminution tumbling mills. Traditionally, the use of perfect mixing has been assumed when modelling the operation of AG/SAG mills. If this were true then the acoustic emissions from AG/SAG mills would be uniform along the length of the mill. Experimentally this has been found not to be the case. From another perspective it should not be the case because of the different conditions existing at the feed end compared to the discharge end. This paper presents the results determined by non-contact acoustics and their analysis in terms of understanding of the mechanisms occurring inside a mill.

Aug 8, 2011

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By Minchinton A

CPeX is a non-ideal explosive performance prediction model. The model takes into account the rate of energy release, the extent of chemical reac- tion and the effect of confinement on energy release. The model resolves the explosive energy into `shock' and `heave' com- ponents as a function of explosive type, hole diameter and rock type. The predictions of the model are compared for a bulk emulsion, and a prill-doped bulk emulsion in soft rock. The predictions, based on calibra- tion of the model with simple unconfined detonation velocity measure- ments, show the significant effect of non-ideality on explosive Performance.

Jan 1, 1988

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By E S. B Santiago, C P. N Moreto, L V. S Monteiro, G H. C Melo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Iron oxide-copper-gold (IOCG) systems of the Carajás mineral province (Amazon craton, Brazil) are structurally controlled by regional-scale shear zones and have formed by multiple episodes of fluid circulation and hydrothermal alteration in the Neoarchean (2.71–2.68 Ga and 2.56 Ga) and Palaeoproterozoic (1.90–1.87 Ga).Collectively, fluid inclusion, boron, oxygen and hydrogen isotope data and Cl/Br–Na/Cl ratios in fluid inclusions reveal that regional circulation of non-magmatic brines (eg evaporative fluids/evolved sea water) and mixing with other fluid sources (eg meteoric or magmatic) is an important attribute in the genesis of the Carajás IOCG systems. The ?33S and d34S compositions of sulfides from the Neoarchean and Palaeoproterozoic IOCG systems suggest that the ore-bearing fluids have assimilated sulfur from crustal reservoirs. Nevertheless, most ?33S measurements have indicated mass independent fractionation (MIF) effect for both systems which points to the possible involvement of surface sulfur sources.CITATION:Xavier, R P, Monteiro, L V S, Moreto, C P N, Melo, G H C and Santiago, E S B, 2015. Non-magmatic versus magmatic fluids in the genesis of Archean and Palaeoproterozoic iron oxide-copper-gold systems of the Carajás Mineral Province (Brazil), in Proceedings PACRIM 2015 Congress, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

All companies and individuals who embark on a business venture incur costs. For the most part these costs can be conveniently categorised, firstly into capital and operating costs and then into the various elements of these major cost centres. Although the nature of expenditure naturally differs as between industries certain broad cost types are characteristic of all heavy industries. The capital costs of gaining access to an orebody, equipping a new mine, building a treatment plant and perhaps refining and smelting facilities are likened to capital expenditure by a manufacturer on new plant and equipment required for an expansion or new product innovation. Similarly the day to day costs of labour and materials employed in the running of a mining operation can be likened to similar costs in other heavy industry. There is another group of costs that are not so easily categorised. Most industries incur unavoidable costs that do not form part of the direct or capital costs of physical production. These costs include taxes and other payments to government and research expenditure. The mining industry has a particularly heavy burden of non-production costs and it is the objective here to highlight and analyse a few of them. These costs are exploration expenditure, infrastructure expenditure, royalties and income tax. This is not to suggest that these are the only major non-production costs that the mining industry needs to bear. The industry may incur significant costs for environment protection, land tenure maintenance and on liaising with Government on a wide variety of matters. It is for reasons of subject manageability that the list is confined to the four costs mentioned. For the mining industry, exploration and infrastructure expenditure, royalties and income tax have several distinguishing features. Firstly, they are generally proportionately large costs. Exploration and infrastructure expenditure for example, could well exceed mine development costs. Depending on how royalties are levied, they may be very high in relation to profits earned and many in fact exceed profits. Secondly, except for income tax, they are costs that are generally not payable by other industries. Exploration expenditure is in some respects comparable with industrial research and development. However, because mines are wasting assets exploration is necessary for survival, and it is likely to form a larger part of costs per dollar of profits or sales than R&D. It can therefore be said that exploration is of far more significance to the miner than R&D is to the typical industrial company. Furthermore, unlike exploration expenditure, R&D results are transportable and patents permitting, transferable. The infrastructure burden that miners must carry is unique to the industry. Whereas urbanised industry is not usually liable for the capital cost of power, water, transport, townships and community facilities, the miner must finance these projects himself. Neither the payment of royalties, nor of course, income tax are unique to the mining industry. Royalties are more properly described as a unique charge on some primary industries but however described, they are a charge that manufacturing and service industries do not have to pay. Whilst we all pay income tax, the mining industry's uniqueness derives from the special problem that the industry has in arriving at annual net income in view of the capital intensity of the industry, partly due to expenditure on infrastructure, the indefinite life of capital equipment and its unpredictable residual value, funds expended on exploration and long lead times associated with a mine development. The third distinguishing feature of these costs is that, with the possible exception of exploration expenditure, they are heavily influenced by the policies and actions of Government. As such the industry has a responsibility to promote the industry by emphasising its potential to improve national product including exports and by requesting that the Government provide for the industry in its long term planning and seek its co-operation to prevent the industry incurring inequitable penalties relative to other industries.Finally, exploration and infrastructure expenditure are significant because they are front-end charges on a project. When due allowance is given the time value of money and the deferment of income from a mining development to which they relate, exploration and infrastructure expenditure assume greater importance than the raw money expenditure suggests. For all these reasons, exploration and infrastructure expenditure, mining royalties and mining income tax are worthy of detailed study. This is the purpose of this paper. The objective is to examine the determinants that give rise to them and provide some thoughts on their impact on on-going and potential mining developments and, where relevant, to make some suggestions as to how they may be minimised.

Jan 1, 1977

By F Ramos

Conventional techniques for resource estimation generally involve the laborious analysis of variograms and the specification of parameters for covariance functions. In large deposits, construction of resource models and their update require significant amount of manual work, expert knowledge and time. In this paper we take a machine learning view to the problem of resource estimation. This is a non-parametric Bayesian method, leading to automatic parameter estimation (learning). Through Bayesian learning, the parameters of the model can be obtained by optimising a quantity known as the marginal likelihood. The main advantage of this approach over conventional maximum likelihood estimators is that the objective function incorporates the OccamÆs razor principle. This allows the comparison of different statistical models û for example, models designed with different covariance functions û and naturally penalises complexity, thus avoiding overfitting. Our technique presents significant flexibility for the definition of mean and covariance functions and permits the usage of more sophisticated models.The second contribution of this work is the formulation of a data fusion mechanism that continuously updates the resource model. As mining progresses, more information becomes available. For example, the hardness of the rocks can be measured while drilling blast holes, grades of ore and contaminants are obtained from cone logging. This information is in general available at a finer spatial resolution but can be more uncertain. The data fusion mechanism can seamlessly estimate the uncertainties of the different types of information and fuse them as new measurements are acquired. This procedure can significantly improve the quality of the resource model, defining new grounds for stochastic mine planning. We demonstrate the effectiveness of our approach in estimating iron ore deposits by integrating information about different grades.

Sep 26, 2011

The non-renewable energy resources of Queensland comprise coal, petroleum (oil and gas), oil shale and uranium. Coal is widely distributed., and has been developed extensively both for export and for use within the State. Proven reserves total 5 390 million tonnes recoverable of coking coal and 5 580 million tonnes recoverable of non-coking; very large resources particularly of non-coking coal are still to be quantified by further drilling. Annual production is of the order of 20 million tonnes of coking coal, principally for export, and 6 million tonnes of non-coking, mainly for power generation within the State. Petroleum resources are meagre in com- parison with those of coal. Initial recover- able reserves of liquids (mainly in the now substantially depleted Moonie Oil Field) totalled only 4.2 million m3. Initial recover- able reserves of gas (mainly in the western Surat and Bowen Basins) totalled 7 800 million m3. Annual production is of the order of 64 thousand m3 of liquids for refining in Bris- bane, and 268 million m3 of gas mainly for production of fertiliser and for industrial and domestic heating, in Brisbane. Prospects are fair for the discovery of additional reserves. Two deposits of oil shale are potentially of economic significance. The Rundle deposit at The Narrows in central Queensland has the

Jan 1, 1979

The paper reviews winder rope inspection procedures at the Non Destructive Testing (NDT) Unit of Western Australian School of Mines (WASM) and outlines measures taken to adopt the world's best practice. The measures include acquisition of a new type of rope tester, adoption of comprehensive rope rejection criteria, adoption of a standard rope inspection procedure and formal training of the wire rope inspectors.

Jan 1, 1995

HISTORY OF PROCESS DEVELOPMENT The manufacture of coke from coal commenced at the beginning of the 17th century by heaping coal into circular mounds in the open, covering with earth, clay or ash and slowly burning the coal in the mounds to produce a heap of coke. Naturally the process was slow in production rate with low coke recovery due to the loss of that part of the coal which was completely burnt to ash. As a natural consequence of this initial carbonisation method, a coke oven design was developed so that the coking chamber, which was constructed of brick, was circular in plan, cylindrical in section with a dome shaped roof - similar in shape to the original coal mounds. As the shape of the chamber was similar to the old dome shaped beehive, the ovens were called beehive ovens. The ovens were built in long single or double rows with retaining walls between each oven and as such were known as a battery of beehive coke ovens. In these early beehive ovens, coal was charged from hand wheeled tubs into a hole into the top of each oven, hand- levelled with a rake and the oven side opening sealed with bricks and clay except for some small holes in the opening to admit limited quantity of air for combustion. Coking commenced by the heat retained in the brickwork from the previous charge. The gases evolved from the coal, together with the admitted air, were partially burnt inside the oven to supply the heat for carbonisation and the surplus gases were burnt to waste at the top charging hole. The heat from this gaseous combustion inside the oven together with the reflected heat from the brickwork of the arched roof of the oven allowed carbonisation of the coal charge to proceed from its surface slowly downwards to the floor of the oven. At the end of the coking cycle (usually 4 or 5 days) when there was no more evolution of gases, as indicated by diminishing gas flame and a drop in oven temperature, the brickwork of the oven opening was removed. The coke was then quenched by inserting a pipe with spray holes to spray water over the coke charge in the oven after which the coke was raked from the oven. The work of charging and levelling the coal, bricking and removal of oven opening, quenching and raking out the coke all required manual labour. As these ovens only carbonised a 5 to 7 ton charge of coal per cycle of 4 to 5 days, to produce 3 to 41/2 ton of marketable coke, the labour required per ton of coke was high.

Jan 1, 1975

By A Coulson, J Hussey

Noranda Inc is a Canadian mining and metallurgical company with its activities managed through businesses in copper and recycling, zinc, aluminum, magnesium and various metals through its interest in Falconbridge Ltd. Noranda operates three base metal mines, three copper smelters, one copper refinery, one zinc refinery, one lead smelter and refinery, three copper recycling and sampling facilities seven aluminum producing facilities and one magnesium production facility in the construction stage. The mining side of Noranda has a strong history of open stope, cut and fill and shrinkage mining. The 1999 Noranda Annual Report lists a 206 million tonne resource located at Porphyry Mountain in GaspT, QuTbec. Mont Porphyre is a large tonnage, low-grade porphyry style Cu-Mo deposit that was discovered in 1994. It is located at a depth between 1.0 and 1.7 km below surface and characterised by a very competent rock mass. The Mont Porphyre resource is located adjacent to the town of Murdochville, close to NorandaÆs Mines GaspT operations. Mines GaspT closed its open pit and underground operations in 1999 after approximately 45 years of mining, but still operates a copper smelter near Murdochville. The low-grade and great depth of the Mont Porphyre resource suggested that mine design could not be based on the conventional Noranda open stoping mining practice. This paper will review NorandaÆs approach to evaluating the Mont Porphyre deposit. The approach included two definition diamond drilling campaigns, a review of current caving practice, an in-house scope study, a geotechnical logging program for diamond drill core and participation in an international study on cave mining. One interesting component of NorandaÆs approach was the scope study that involved a team of multi-disciplinary personnel drawn together for a short period of time. The objective of the scope study was to determine what conditions would be necessary to mine the deposit and to assess the merits of continuing with further exploration work. A review of current worldwide underground bulk mining practices, and in particular an evaluation of the applicability of caving mining methods, were key components of the scope study. The scope study team concluded that derivatives of caving could be applied to the mining of Mont Porphyre, but additional diamond drilling was recommended to further define the deposit and improve the level of geotechnical information. Following the recommendations of the scope study team, a diamond drilling campaign was completed during the summer and fall of 1997. The 1997 drilling campaign had two secondary objectives, in addition to the primary objective of defining the limits of the orebody. The first objective was to improve the level of geotechnical information available for the characterisation of primary block cave fragmentation. The second objective was to improve the delineation of a lower grade intrusive core. A geomechanical investigation was conducted and included particular emphasis on geotechnical data collection and analysis. A review of the actual data collection process, including several trials of different core orientation techniques, will be included in the discussion.

Jan 1, 2000