Search Documents

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

By Susanto A

As part of the current NERDDC funded project studying Dragline/Hopper/ Crusher/Conveyor systems for overburden removal, an investigation was carried out to assess the feasibility of automating the swing-to-dump phase of the dragline digging cycle in order to main- tain consistent performance of spotting the bucket above the hopper prior to dumping. The study involved design of automatic position controls for the hoist, drag and swing drives and simulation of detailed mathe- matical models of the three electromechanical systems and their associated electrical control schemes. The design of the hoist and drag systems to position the bucket in the boom plane is relatively straightforward. Simulation results show fast and accurate performance, with no evidence of interaction between the two drive systems through the ropes. The design of the swing position control system involves special strate- gies to cater for variable inertia and to damp the pendulum oscillations of the bucket. The use of a bucket pendulum model and variable dynamic compensation embedded within the feedback control loop, along with optimal speed/angle slowdown trajectories, has yielded fast and damped positioning responses under simulation.

Jan 1, 1989

By Toop G. W, Martin M. T

At the Cominco Ltd plant in Trail, British Columbia, the Betts lead electrorefining operation requires that antimony and arsenic be present in the lead bullion for anode slimes stability control. Until 1986 the antimony and arsenic inputs from concentrates to the Lead Smelter needed to be supplemented with high antimony and arsenic content recycles from the Silver Refinery operation to maintain a satisfactory composition. Subsequently the antimony and arsenic inputs have increased as a result of increasing levels of antimony in Sullivan lead concentrate and the purchase of larger quantities of silver/gold bearing concentrates that inherently have higher antimony and arsenic levels. The increase has exceeded the limits required by the Betts process. It therefore became necessary to install a partial softening process downstream of the Continuous Drossing Furnace to satisfactorily control the bullion composition. Process control and oxygen injection techniques used in the partial softening process are reviewed. Approximately 8 tonnes/day of softening slag are produced having a combined antimony and arsenic content of 25 percent. This slag is reduced in a recently commissioned short rotary furnace followed by vacuum distillation of the metal for recovery of the antimony and arsenic values.

Jan 1, 1989

By R Nicholson, N D. Cox, N W. A Lambert

"This paper reports on the long-term operation of a particle density meter (PDM) at the Bloomfield coal handling and preparation plant (CHPP). This unit has been operating continuously for over three years, providing real-time data to the operators to allow the monitoring of flotation circuit performance. PDM outputs include slurry density, solids concentration on both mass and volumetric basis, and particle density. Knowing the average particle density of a stream allows for the optimisation of the process in real-time.The calibration of the solids concentration measurement device proved very difficult as the factory calibration techniques and existing laboratory analysis did not give accurate or reliable results. The solids concentration device had to be re-engineered and a new calibration method developed that gave accurate and repeatable results. Independent verification of samples taken from the PDM was undertaken as part of the trial process.The operational reliability of the PDM was a major point of investigation. The initial installation of the unit revealed issues with large, misplaced material of up to 20 mm periodically entering the unit, leading to feed blockages. The presence of these misplaced, oversized particles in the flotation circuit was resolved by installing innovative automatic back flush systems on the PDM.From a plant perspective the PDM has been an invaluable instrument that has enabled irregularities in the flotation circuit performance to be identified, which sampling had not and could not readily identify. This was achieved by close monitoring of real-time tailings composition on a minute by minute basis over short and extended periods. Variations in the tailings stream with respect to particle density and solids concentration were traced back to other issues in the plant. In addition, the PDM has allowed cell optimisation with respect to reagent dose rate to be improved. The PDM with real-time feedback can negate the need for large sampling campaigns and analysis during plant optimisation programs.Citation:Lambert, N, Cox, N and Nicholson, R, 2016. Particle Density Meter, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By B Ekberg, R Salmimies, T Kinnarinen, A HSkkinen

The regeneration of the ceramic filter medium used in iron ore dewatering is often done by combining backwashing, ultrasonic cleaning and chemical regeneration. Of these three, the first two are applied more frequently, whereas chemical regeneration is done only when needed, eg once a day. Chemical regeneration of the ceramic filter medium in iron ore processing can involve the use of oxalic acid to dissolve the iron oxide particles. Even while performing simple chemical regeneration, meaning no ultrasound to assist the cleaning, the changes in the performance and in the structure of the filter medium could not be explained solely based on the dissolution or the removal of particles from the surface. Good regeneration results were obtained at 35 and 50¦C, meaning that the final permeability of the filter medium corresponded to that of unused filter medium. Permeability of the medium after regeneration at 15¦C was also good after 12 h, but did fall short of those regenerated at higher temperatures. Changing the acid concentration did not seem to have a significant effect on the regeneration.CITATION:Salmimies, R, Kinnarinen, T, Ekberg, B and HSkkinen, A, 2013. Particle dissolution in the chemical regeneration of the ceramic filter medium used for magnetite dewatering, in Proceedings Iron Ore 2013 , pp 473-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Particle Mechanics and the Design of Cyclone Tribochargers Triboelectric separation is a dry electrostatic technique that has shown promise in several particle processing applications. A tribocharger uses contact or friction to differentially charge particles of different materials, which are then separated by an electric field. The initial tribocharging process is poorly understood, with tribocharger design and operation largely a matter of trial and error. A better physical understanding of tribocharger operation would therefore be of immense value in the optimisation of triboelectric separation processes. A combination of charge measurements, trajectory modelling and high-speed video has been used to relate charging to particle mechanics in a cylindrical pneumatic cyclone, one of the most effective tribochargers for mineral separation applications, and the preliminary results are presented here. The consequences of these observations for cyclone tribocharger design and operation, and for tribocharger design in general, are discussed.  

Sep 13, 2010

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

By K C. Runge, E Tabosa, A Jankovic

Flotation recovery in geometallurgical modelling is usually predicted based on relationships developed from batch flotation testing of different ore types. These batch flotation tests are usually performed at a constant set of operating conditions and at a fixed feed grind size P80. Usually the laboratory feed grind P80 is that which is expected to be produced in the full-scale flotation circuit for that particular ore type.Flotation recovery will be a strong function of the valuable mineral particle size distribution, with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation of this fraction. This valuable mineral particle size distribution is not characterised by the solids P80 parameter alone. The proportion of material in each class will also be a function of the slope of the size distribution and the degree of preferential grinding of the valuable mineral in comparison to the total mass of the ore.This paper will demonstrate (through example) how these other size distribution parameters can change with a change in grinding technology, the size and operating conditions used in a grinding unit and the characteristics of the classification technology used in conjunction with the grinding unit. Case studies will be presented that demonstrate how this can result in these parameters being very different in laboratory testing to that produced in the full-scale comminution circuit. A rule of thumb that laboratory rod milling rather than ball milling produces a size distribution most similar to that of the full-scale grinding circuit will be challenged. These differences can result in a significant change in flotation recovery. It is therefore important to consider these parameters when developing a laboratory geometallurgical program, to enable more accurate prediction of the flotation recoveries that will be achieved in the full-scale process.CITATION:Runge, K C, Tabosa, E and Jankovic, A, 2013. Particle size distribution effects that should be considered when performing flotation geometallurgical testing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 335-344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

The mineral pulp as it passes through grinding-classification, flotation and solid-liquid separation is examined in the context of it being a particulate fluid. By focussing on the complex viscosity and yield stress of the fluid, new control strategies are discussed. The mineral-particulate fluid is dominatred by non-Newtonian rheology (ie shear thinning, shear thickening, shear yield stress and compressive yield strength). The control of this Theology is seen to be dependent on the fundamental practice-particle interaction forces and with adequate information, it is possible to use the complex shear properties to advantage. The advantages, in terms of final waste and concentrate management, to high weight per cent solids in the mineral particulate fluid, are explored and control strategies outlined.

Jan 1, 1993

Over the past few years, there has been an emerging relationship between business and civil society, especially NGOs. This relationship has the potential to bring about significant change, identifying common ground between commercial and societal interests. The mining industry has been a leader in acknowledging the need for community consultation and engagement. This paper argues that partnerships can make a very significant contribution to the industry as it comes to terms with the dilemma of an open economic system pushing against a closed ecological system.The paper will pose a number of questions: where is the locus for debate about sustainability in the mining sector?; how well embedded within companies are the new competencies that Leon Davis first identified in 1995 for the mining sector?; how has education for mining engineers or exploration geologists changed to prepare people for what are very different expectations within the working environment?; how well is the industry doing in managing its own environmental impact and what is its responsibility to an agenda for sustainability which extends beyond its own operations?;and how can NGO partnerships contribute to more sustainable outcomes? The paper does not aim to answer these questions, but to explore them in the hope that the issues and possibilities raised will contribute to advancing progress towards sustainability within the industry.

Jan 1, 2002

A mining joint venture presents a real management challenge to achieve harmony with the other participants in the successful development and operation of a mine. This can best be facilitated by a detailed agreement and guided by a set of joint venture principles which recognise the differences of the interests of the parties and seek to establish sound business and personal principles by which differences not anticipated in the agreement might be resolved. The major and minor co-venturers can and do present potential difficulties to one another. This paper, one of the pair in the joint venture panel discussion session, predominately presents the minor's viewpoint. Usually commercial matters such as project finance, areas of interest, divestment, pre-emptive rights and decision-making can be adequately covered in the agreement. However, when the parties disagree and have difficulty in resolving their differences, the joint venture principles should be used to advantage to resolve relationship difficulties.

Jan 1, 1997

Partnering has come to prominence in the Australian construction industry in a formal sense this decade. The high level of disputation in the building and civil construction industries in the 1980s drove its development in both Australia and North America. PartneringÆs use has been most prominent in the construction industry, particularly in the civil and construction sectors of the industry. It has found favour in some mining development projects, one of the most notable being BHP MineralÆs Cannington project in NW Queensland. This paper examines the requirements of successful partnering agreements and describes in detail the mine development partnering agreement at Cannington. In particular, the paper discusses the authorÆs experience and recommendations for partnering to avoid contractual problems and achieve win û win project outcomes for all parties to major mining projects.

Jan 1, 1999

The geotechnical factors controlling the design of the open pit slopes of the Pasminco Century Mine near Lawn Hill, Queensland are presented below. Pasminco Century is a stratiform shale hosted zinc deposit in the Lawn Hill Formation that is overlain in part by the Thorntonia Limestone Formation. Both the mineralisation and overburden is located within a competent rock mass such that intact rock strength and discontinuity spacing is generally sufficient to prevent large-scale slope failure by breakage through the rock mass. Rather, overall slope stability issues are dominated by the major discontinuities within the rock mass. The deposit is located in a structurally complex regime, it consists of a synclinal basin which is truncated by easterly striking normal faults through its centre and northern and southern limits and by an unconformity on its eastern and western margins. Deposit geometry and slope stability is further complicated by small-scale folding, a pattern of northeast and southeast striking subvertical faults and north easterly dipping thrust faults with their associated fault emplaced blocks of Lawn Hill Formation in the overburden. The large size of the deposit requires a staged mining approach with the excavation of both final pit walls around the external sides of each stage and interim pit walls along the internal boundaries between adjacent stages. The deposit geometry and major discontinuities control not only the final pit wall design but also interim wall location and orientation, excavation sequence and in some stages the excavation schedule. Two and three-dimensional limit equilibrium stability analyses were conducted using both deterministic and probabilistic approaches to determine appropriate pit wall design criteria and to select a suitable excavation sequence and schedule.

Jan 1, 2000

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022

By B Robertson

Over the 40 years that the author has been engaged in the Australian underground coal mining industry, there has been a continuous improvement in safety performance as the sector has grown in size and productivity. The underground environment hosts many hazards with significant risk profiles that are kept in check by effective health and safety management systems that have evolved largely following major underground disasters. Observations are made on the changes observed for specific aspects of the underground coal sector, with particular reference to ventilation issues, and predications are made as to the needs of the future.CITATION:Robertson, B, 2013. Past achievements and future challenges in the underground coal sector, in Proceedings The Australian Mine Ventilation Conference , pp 27-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The early records of hydraulic elevator and bucket ladder dredging in the Clutha River system indicate the success of that era of alluvial gold mining in Otago. This paper briefly reviews parameters of depth and gold grade for alluvial operations. The application of dragline technology is proposed for the economic removal of overburden to target the deeper alluvial gold areas which remain in the Otago region.

Jan 1, 1992

As in other countries, gold mining inNew Zealand has been cyclic in character. Looking at these cycles may provide insights as to what may occur in the future and that is the basis for this study.   New Zealand has experienced four gold mining cycles. The first began in 1857, peaked in 1866 and terminated in 1890. This cycle was characterised by alluvial gold mining by individuals and small groups. This is referred to as the Labour Led cycle. The second cycle began in 1890 and reached its peak in 1906 and terminated in 1929. This cycle was characterised by the use of dredges in alluvial gold mining and was also the peak of hard rock mining. This cycle is referred to as the Technology Led Cycle. The third cycle peaked in 1940. This cycle was far less significant than the previous cycles, arising out of the depression when the unemployed embarked on small scale alluvial mining. This overprinted the continuing decline that occurred after 1906. This cycle is here referred to as the Depression Overprint Cycle.   The fourth cycle began in 1984 when production began to climb rapidly from a very low base. The growth in production was spurred by rising gold prices in the early 1980s resulting in relatively low grade gold-bearing alluvial ground becoming economic. But in the 1990s, production from the new hardrock mines in Coromandel and Otago has overshadowed alluvial production. This cycle is here referred to as the Price Led cycle.   What are the future prospects for gold in New Zealand? Although there are many factors involved, this will be largely determined by two factors; firstly, continued access to prospective gold-bearing properties, and secondly, the price of gold. Based on these factors, three future industry scenarios have been developed. The first of these is industry collapse, in which access to prospective property is constrained and prices mayor may not weaken. The second is industry consolidation, in which the available ground is accumulated by a small number of large companies who can use economies of scale to weather price fluctuations. The third scenario is industry growth, in which access to prospective ground is constrained in environmentally sensitive areas but is otherwise relatively unconstrained. Efficient companies are allowed to work in a policy and economic framework that allows them to make a major contribution to the economy.   While the industry cannot control these critical factors, a good knowledge of the positive role gold mining could play in the future economy may provide a framework by which the access issue, in particular, may be addressed from a balanced perspective.

Jan 1, 1994

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998