Search Documents

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991

By Taylor R. K A, Berglin C. I K

The manganese ore deposits at Groote Eylandt are quite variable both in regard to grade and physical cond- ition. In order to treat a wider range of these ores and to increase production a new primary-crusher and' concentrator complex costing $8 million has been installed and commissioned to treat ore at the rate of 12,000 tonnes per day. The initial testwork carried out to determine the method of the ore treatment required, and on which the design of the concentrator was based, is detailed. The flowsheet and equipment used is discussed together with the operation of the plant. The production achieved and product qualities obtained are given.

Jan 1, 1973

Processing of Hard-to-Treat Copper Ore and Flotation Middlings Using Chemical Treatment

Sep 13, 2010

By O Ostrovski

Iron ore reduction and iron cementation by CH4-H2-Ar gas was investigated in a laboratory isothermal fixed bed reactor. Iron ore was first reduced to metallic iron by hydrogen, then carburised to cementite by methane. Increasing temperature and hydrogen content accelerated the reduction process. Methane had almost no effect on the reduction process. Meanwhile, higher temperatures increased the rate of cementation and also the rate of free carbon deposition. The optimal temperature for cementite formation was found to be 750¦C. At this temperature, reduction of iron ore to cementite by gas containing 55 vol per cent hydrogen, 35 vol per cent methane and 10 vol per cent argon was completed in about 15 minutes. Addition of sulphur into the reducing/carburising gas strongly retarded the process of cementite formation and free carbon deposition. Cementite is an unstable phase which decomposes to iron and carbon. The rate of cementite decomposition increased with temperature up to 600¦C and above 750¦C . In the temperature range from 600¦C to 750¦C the rate of cementite decomposition decreased with temperature. Cementite was the most stable at 750¦C and least stable at 600¦C. The two-interface grain model was used to describe the process of iron ore reduction and the volume reaction model was employed to model the iron cementation process. The simulated results for both reduction and cementation are consistent with the experimental data.

Jan 1, 2000

By A B. Christie

Space-based synthetic aperture radar (SAR) data is becoming available over much of the world, includingNew Zealand. Radar imagery has a number of very advantageous features, including all-weather capability; it also has artifacts, such as layover, which require processing before these data may be used to best effect.   This paper gives an outline of SAR, details the image processing required, and discusses the use of the first New Zealand Japan Earth Resources-1 SAR data to aid geological mapping on the Coromandel Peninsula.

Jan 1, 1994

By A Jankovic, D David, P Payne

Although the majority of current steel production is supported by iron ore sourced from high-grade haematite deposits, the long-term growing demand for steel has led to higher raw material prices and opened the way for many new magnetite deposits to also be developed. There is a rich and long history of magnetite ore processing in Western countries, including large operations such as Cleveland Cliffs in the USA and LKAB in Sweden, as well as smaller operations like Savage River in Tasmania. The challenge for virtually all magnetite operations is to minimise operating costs, which is dominated by the cost of power required to fine grind the ore in order to achieve acceptable concentrate iron grade together with low impurity content. This remains the case today and will be even more important in the future when a carbon tax is expected to become a significant addition to the operating costs for magnetite deposits. Historically, the lowest operating cost was achieved by multistage fully autogenous grinding with integrated magnetic separation steps between the stages. The major benefit of fully autogenous grinding is the elimination of steel grinding media costs and the need to discriminate between steel and magnetite in coarse magnetic separation. The separation step between grinding stages progressively reduces the amount of material to be ground. Application of more efficient grinding technologies developed in the last 20 years, including high pressure grinding rolls (HPGR) for fine crushing and stirred milling for fine grinding, has provided opportunities to further reduce the operating costs associated with comminution. Both technologies are already implemented in some magnetite processing operations, although in limited capacity. The results of a theoretical option study for high capacity processing of a hard, fine-grained silica-rich magnetite ore is presented in this paper, with the emphasis on comminution circuit options. Several circuit options are ranked based on a net present value analysis incorporating an estimate of carbon tax added in the operating cost. The study demonstrates the significant advantages of applying more efficient autogenous grinding technologies.

Jan 1, 2009

Robe River Iron Associates (RRIA or Robe) is widely regarded as the worldÆs most cost-effective, consistent and reliable supplier of iron ore. It has been in operation since 1972 and globally is the fourth largest seaborne trader in iron ore exporting 25.5 million tonnes of -9.5 mm sinter fines and 4.5 million tonnes of pisolite lump (-31.5 +6.3 mm) during 1999. Robe is a joint venture that controls major iron ore resources in the Pilbara region of Western Australia. ItÆs participants are North Limited with an interest of 53 per cent (65 per cent including minority interests) and Japanese companies Mitsui (33 per cent), Nippon Steel Australia (10.5 per cent) and Sumitomo Metal Australia (3.5 per cent). Robe River Mining Co Pty Ltd manages the project which is a subsidiary of North Limited and Mitsui.

Jan 1, 2000

The energy input requirement to produce the molten slag associated with iron production to the modern Australian blast furnace, is estimated to be 2.OMJ/kg. In converting blast furnace slag to products of higher commercial value, advantage should be taken of this energy content by transporting molten slag from the furnace for beneficiation and processing in the molten state at an "off furnace site". The refined slag melt may then be converted into a variety of products for use in the building and construction industries, e.g. slag cement, slag sand and slag aggregates, insulation wool and various slag ceramic products. Some results of studies into slag melt beneficiation and conversion processes involving both molten and cold granular slag raw material, are presented.

Jan 1, 1979

By L O. Filippov, I V. Filippova

Subsea massive sulfide deposits have particular mineralogical compositions and textural features differentiating them from onshore ore. When extracted from salty water and exposed to the air, massive sulfide samples strongly oxidise and soon become covered by thin layers of iron, copper and zinc-rich sulfates and oxides, as well as elemental sulfur. The textural properties vary according to the degree of maturity and the sample position within the hydrothermal deposit. Because of the variation of secondary mineralisation and porosity level, sea floor massive sulfides respond differently from terrestrial ore to processing methods. Froth flotation, commonly applied to separate all types of sulfides from the gangue minerals, is one possible treatment technique to process sea floor ore. Sulfide recovery rate is, in most cases, excellent (>90 per cent). However, separation of the various mineral phases is difficult to obtain even when applying known methods used for onshore ore. Moreover, the flotation behaviour decreases dramatically with time of conservation, even when the samples were stored in a confined environment. High pH range, which is a good way to depress pyrite and therefore to favour the flotation of copper and zinc sulfides, does not have the same effect on subsea ore. Consequently, careful flotation procedure should be elaborated to obtain efficient mineral separation for this specific marine ore.CITATION:Filippov, L O and Filippova, I V, 2015. Processing of subsea massive sulfide ores by flotation – similarity and features with terrestrial ores, in Proceedings Third International Future Mining Conference, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By E Mare

Recent highly publicised incidences of disastrous containment failures, none more pertinent than the 2019 iron ore tailings dam failure in Brumadinho, have focused the world’s attention squarely on the often-challenging subject of tailings storage. Unwanted ultrafines, that are deemed to be unworthy of further treatment or not to have further saleable value, are therefore a significant issue for mine owners looking to reduce risks and perceptions associated with long-term storage of tailings. In this context, there are strong drivers to identify safer approaches to ultrafine tailings management, especially if it can also lead to increased revenue, together with better water stewardship and environmental outcomes. The better management of tailings needs to be considered from both containment challenge and processing opportunity perspectives. This paper focuses on the latter, reviewing from a technical and economic perspective, the feasibility of more extensive processing and/or reprocessing of specifically iron ore tailings, in a bid to reduce the overall volume for management in long-term storage. Herein the opportunity lies in recovery processing, as much as enhanced thickening and/or mechanical dewatering, and therefore the paper discusses both issues as equally important sides of the same coin. Recent interest in iron ore ultrafines processing and reprocessing studies suggests that the enhanced processing of iron ore tailings offers multiple perceived advantages. Apart from a potential reduction in tailings volume, associated with safer containment, lower environmental impact and improved water management, the prospect of increased revenue from additional Fe recovery presents supplementary motivation for iron ore players to embrace this approach, as further elaborated in this paper.

Nov 8, 2021

By Y Yang, J Skrypniuk

The Jinfeng mine is Sino Gold's flagship project and is the second largest gold mine in China. Sino Gold Limited (SGL) holds 82 per cent equity in the Sino-Foreign joint venture Sino Guizhou Jinfeng Mining Limited (SGJML) with a Chinese partner. Jinfeng is located in a relatively remote site in southwestern Guizhou province. The orebody is considered to be the largest known Carlin type deposit in China. Jinfeng Plant has the world's third largest BIOX« bacterial oxidation facilities (790 t/d), treating highly refractory concentrate generated from crushing, semi-autogenous grinding (SAG) and ball milling and bulk sulfide flotation operations. The Jinfeng Plant construction started in February 2005, commissioning was completed in April 2007, and commercial gold production was achieved in September 2007. This paper describes the successful operations of Jinfeng Plant over the last two years. The key events of the project development are described, from the project background and process design, through to the commissioning and achieving design mill throughput of 3600 t/d resulting 180 000 ounces of gold per year. Process aspects of the BIOX« and carbon-in-leach (CIL) operations over the last two years are discussed which illustrate a very high BIOX« oxidation rate (more that 97 per cent) and excellent CIL recovery (more than 96 per cent). The management of the Jinfeng plant CIL tailings detoxification and filtration is described, and Jinfeng has became the first BIOX« processing plant to have achieved dry stacking of detoxified and pressure filtered CIL tailings. Current efforts to recover cyanide from CIL detoxified solution and the achievement of a zero discharge site water balance are also introduced. Many improvement projects have been made over the last two years which have culminated in a 15 per cent increase in mill throughput over the design and BIOX« CIL recovery increasing from 92.5 per cent to 96 per cent. Significant operating cost reductions from lowered of acid, lime and cyanide usage through process modifications and technical innovations are discussed.

Jan 1, 2009

The prospect of utilisation of phosphate ores which contain high P2O5 values associated with Al and Fe has produced a great deal of interest over many years. Processing options have generally been based on the utilisation of by-products which were required to offset the processing costs.   This paper presents a range of processing options which have been investigated at laboratory or technical scale on phosphate ores which predominantly consist of crandallite, CaAl3(PO4)2(OH)5.3H2O and millisite, Ca(NaK)Al6(PO4)4(OH)9.3H2O. Christmas Island (Indian Ocean) and Mt Weld (Western Australia) phosphate ores are good examples of such feedstocks. It is expected that these processes may also be applicable to such phosphate ores from other locations.

Jan 1, 1990

The prospect of utilization of phosphate ores which contain high P205 values associated with Al and Fe has produced a great deal of interest over many years. Processing options have generally been based on the utilization of by-products which were required to offset the processing costs.This paper presents a range of processing options which have been investigated at laboratory or technical scale on phosphate ores which predominantly consist of crandallite, CaA13(PO4)2(OH)5.3H20 and millisite, Ca(NaK)Al6(PO4)4(OH)9.3H20. Christmas Island (Indian Ocean) and Mt. Weld (Western Australia) phosphate ores are good examples of such feedstocks. It is expected that these processes may also be applicable to such phosphate ores from other locations.

Jan 1, 1990

By M I. Pownceby, S P. Suthers, V Nunna, G J. Sparrow

Global demand for iron and steel has increased substantially over the past 20 years and there has been a greater focus on developing suitable processing options to treat low-grade hematite-goethite ores containing higher levels of silica and alumina impurities. The processing applicable to reduce the impurity levels in these lower-grade iron ores depends on their mineralogy and a thorough understanding of the process dynamics associated with the separation technology. Different separation technologies used to remove silica and alumina from low-grade iron ores were reviewed. The major concentration methods that may be applied to upgrade lower-grade lump iron ores include magnetic separation, wet and dry heavy media separation, and air-pulsed jigging. The technologies applicable to beneficiating iron ore fines include wet and dry gravity and magnetic separation, flotation, and roasting followed by magnetic separation. It is necessary to investigate the application of separation technologies on a case-by-case basis to select economically viable beneficiation strategies suitable for the particular low-grade iron ore. A commercial flow sheet is expected to involve the implementation of several separation technologies.

Nov 8, 2021

By J Watt

The Hidden Valley Gold Project is located in a remote and mountainous area of the Morobe Province approximately 30 km south of the township of Bulolo and approximately 90 km south-southwest of the provincial capital, Lae. The Hidden Valley deposit was discovered in 1984 with the nearby Hamata and Kaveroi deposits discovered in 1987 and 1992 respectively. Reserves (Harmony, 2009) at these three deposits are 42.1 million tonnes of ore containing approximately 2.9 million ounces of gold and 45 million ounces of silver. A further 5.4 million ounces of gold and 84 million ounces of silver are in the resources category. The process plant is designed to treat 4.2 million tonnes per year of gold/silver ore extracted by open cut mining methods. Ore is classified into three ore types according to oxidation state: oxide, transition and primary. The silver to gold grade ratio is high for the Hidden Valley and Kaveroi ores, generally in the range 15 - 20:1, and much lower for Hamata, typically 1 - 2:1: Primary ore is the dominant ore type at Hidden Valley with sulfur grades up to about two per cent sulfur. Oxide and transition ores are more prevalent at the Hamata deposit, but its primary ore has up to five per cent sulfur grades. Variable ore types, particularly in the initial years of operation, high silver to gold ratios and limited plant site area, due to the challenging terrain, present the main processing challenges for this project. This paper describes the operating strategies and process development for the main areas of this circuit, highlighting selections of processes and equipment that achieve cost effective, yet flexible solutions to the treatment of ores from these deposits.

Jan 1, 2009

Declining metal prices over the last few years have reduced the number of new metallurgical plants being built and limited opportunities for introducing new processes. However, technological advances are still being made. With increasing economic pressures, the emphasis is now on reducing unit costs by making equipment larger and through use of technologies with lower operating costs. This trend can be seen in the increasing size of grinding mills and flotation cells used in recent plant designs and in the adoption of HPGR crushing as an alternative to SAG milling. Few new technologies achieve widespread introduction until there are clear economic or operational drivers. These might currently include: ò          increasingly stringent environmental standards; ò          availability of exotic materials for equipment construction; ò          increasingly sophisticated instrumentation and control systems; ò          the need to treat increasingly refractory oretypes; and ò          the length of supply routes to many new plants. As a result of these drivers, a number of new and revitalised technologies will get increasing prominence in the design of new operations, such as: ò          use of ultrafine milling equipment such as MIM's Isamill for treatment of refractory gold ore concentrates; ò          use of thiourea as an alternative for cyanide in sensitive locations; ò          novel hydrometallurgical routes for treating base metal ores in remote locations; ò          paste thickening for tailings deposition; and intensive cyanidation of gravity concentrate

Jan 1, 2000

By G M. Taylor

The application of high technology to monitor and control fire life safety, critical functionality in tunnels and underground spaces generally has progressed at an ever accelerating rate over the past decade. Today these systems comprise some of the most complex and little understood aspects of the tunnel/underground facility construction industry, with this area being perceived as high risk comprising impenetrably complex ‘black box’ technology covered in blinking LEDs. This paper will seek to explode some urban myths and common misconceptions associated with such systems, providing its intended audience with a review of what all this technology comprises and where the real risks lie in its delivery lie.The author contends (and looks to support such contention via this paper) that by applying baseline project and risk management processes to the procurement of this widely misunderstood black box technology, the quality of the final outcome can be much improved, driving innovation, reducing both cost and significantly mitigating delivery risk.CITATION:Taylor, G M, 2014. Procuring control and intelligent traffic systems for major new build projects – avoiding pitfalls and maximising value, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

An effective production control system should maximise recovery of economic material from the resource. To do this, internal waste must be accurately delineated and efficiently removed. Achieving this is most difficult in low grade blocks just above and just below the cut off grade, where ore:waste separation follows assay or statistical, rather than geological boundaries. Difficulties arise from sampling errors, configuration of the economic mineralisation, and local variations in geology. Mine bench parameters and mining equipment size apply further constraints to the actual field separation of the ore from the waste. At BCL, management of the resource starts with an effective orebody model for planning, scheduling and ore:waste prediction. Ore production from each mining location is reconciled with concentrator tonnage and grade, and the reconciled grades are compared with the planning orebody model to highlight any Differences.

Jan 1, 1986

Utah Development Company operates a mine at Blackwater with a present annual production of 4 000 000 tonnes of coking coal. Mineable seams outcropping on the company's lease are part of the Permian Mammoth Rangal Coal Measures. Current operations are based pre- dominantly on the Main Lower seam. Coal quality variations occur along the seam strike, in the direction of seam dip, within the seam plies and in isolated anomalous areas. Raw coal of non-specification quality is washed to reduce ash and sulphur and to improve the free swelling index. Raw coal meeting specification quality is sent directly to product, by-passing the washplant. Careful attention to mining, coal preparation and product blending is necessary to ensure that the combined product meets specifications.

Jan 1, 1974

By J de Vries

Arthur Page, a past President of AT&T said:All businesses in a democratic society begin with public permission, and exist by public approval. Product stewardship in its most basic form is simply risk management applied to the products we produce. Conceptually it may be considered as a more expansive approach to many existing safety, heath and environmental programs. Key differences include the extension of responsibility beyond the direct control of management, and consideration of the implications your products and processes have on the broader community, as opposed to the confines of an individual mine site or operation. This paper reviews the processes used by Orica Ltd to manage its product stewardship program. OricaÆs product stewardship program is expansive and supports activities and business that range from manufacture and delivery of commercial explosives and sodium cyanide to mines throughout the world, supply and operation of municipal water facilities, and manufacture and distribution of consumer products such as household paints and adhesives. We highlight the development of the program through experience both good and bad, and by use of case studies to illustrate how an active product stewardship program is an effective business risk mitigation strategy.

Jan 1, 2006