Search Documents

Recovery of Tantalum Capacitors from Waste Printed Circuit Boards Using a Pneumatic Separator

Sep 13, 2010

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By N Rivera, A Music, C Cisternas

In an underground mine operated with panel caving and subjected to high stresses, geotechnical events such as collapses or rock bursts are fairly recurrent. Both situations can involve risks for people, considerable production losses and increasing operational costs.This paper discusses an operational methodology for the recovery of the undercutting front carried out at El Teniente mine, which uses panel cave mining with post-undercutting, after the occurrence of severe damage due to a seismic cluster. The main objective of the recovery of the undercutting front is to prevent the spread of the collapse to the production level, risking the operational continuity. The methodology is the result of repairs that were carried out in the year 2014 at the North Reserves sector from El Teniente mine. Its characteristics are an undercutting front of almost 1000 m long, with the presence of relevant structures and faults, high stresses and high seismic activity.The practical implementation of the proposed methodology was successful since it prevented the spread of the damage, completely recovered the undercutting front and avoided production losses during the execution of the repairs. Also, considering the origin of the damage and the operations associated to the subsequent recovery of the undercutting front, in this paper we discuss the main control variables to be measured. These variables should allow any operator and short-term planner to take action in mines operated with conventional panel caving in a complex geotechnical environment.CITATION:Rivera, N, Music, A and Cisternas, C, 2016. Recovery of the undercutting front in a mine with conventional panel caving – case study at North Reserves sector, El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 713–722 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

By Clark I, Stockton N, Warren L

Nickel flotation circuits currently experience difficulties in recovering fine particles of pentlandite less than ten microns. By agglomerating these particles using shear-flocculation it is hoped to improve the recovery of these fine particles. A sample of massive sulphide ore from the Kambalda region was separated using magnetic separation to obtain a high grade pentlandite concentrate (> 90 per cent). This was finely ground to produce a sample with particles of 50 per cent minus 10 um in size. This sample was then shear-flocculated using a variety of reagents, including xanthates, dithiophosphate and mercaptobenzothiazole (MBT). The effects of reagent type and concentration, conditioning time, impeller speed and type, and pulp density were studied. Froth flotation tests were also conducted on the shear flocculated pulps to compare the effects of xanthate and MBT on the recovery of pentlandite.

Jan 1, 1992

Recovery of Vanadium from Stone Coal Through an Environmentally Friendly Acid Leaching Technology

Sep 13, 2010

By J P. Wyethe, D P. Padayache, B R. Green

The development of an ion exchange process for the recovery of vanadium from solutions containing low concentrations of vanadium and/or slurries is discussed. The process can be used to improve overall vanadium recovery throughout the plant, and/or to reduce the vanadium concentration of waste materials prior to their disposal. The development of the process on a laboratory and miniplant scale is discussed, and includes:selection of a suitable resin with the desired loading and elution characteristics; laboratory-scale testwork to evaluate the use of the resin in both resin-in-pulp and fixed bed configurations; recovery of a high-value vanadium product from the resin eluate; and a preliminary techno-economic assessment of the financial viability of the process.

Jan 1, 2000

By F R. A Jorgensen, G W. Jensen

A pilot scale experimental investigation of the condensation of zinc vapour from smelter off-gases was performed in conjunction with a mathematical modelling study of the system. The work investigated the feasibility of using the high heat and mass transfer rates associated with a fluidised bed to condense zinc directly from smelter off-gases containing zinc vapour. Of particular interest was whether zinc would revert to zinc oxide during the process of condensation, and whether a zinc fog would form and be carried out of the condenser. A 0.1 m diameter fluidised bed condenser was mounted on the top of a 200 kVA DC electric arc furnace in which mixtures of vapours and gases were generated at 1150 - 1300¦C. The gas/vapour mixtures investigated included Zn/N2, Zn/N2/CO/CO2 and Zn/N2/H2/H2O. Greater than 90 per cent of the zinc was deposited on the zircon sand bed of the condenser, and there was no sign of zinc oxide formation, suggesting that the rate of heat transfer was faster than the reaction rate for zinc oxide formation. There was also no evidence that fog was being formed in the condenser. Using the methods of Kunii and Levenspeil (1991), a mathematical model was developed to predict the behaviour of the fluidised bed condenser. The model enabled the distribution of gas/vapour temperature and bed temperature to be determined as a function of distance from the condenser inlet. Similarly the partial pressure of zinc vapour in the gas mixture, and hence the mass transfer rate of zinc to the particles, was determined. Experimental data allowed validation of the predicted bed and gas/vapour temperatures.

Jan 1, 2000

By Kelley BC, Filmer AO

The chemical oxidation kinetics of sphalerite by Fe(III) was studied at various temperatures and size fractions in sulphate media. The kinetics of Zn extraction followed a pore diffusion control mechanism with an apparent activation energy of 54-58 kJ mole. This figure, although high for a pore diffusion control process, is consistent with other studies carried out in sulphate media. An empirical statistical model, relating the extraction time to % Zn extraction, average particle size and temperature, is described by log 1 = 12.22 - 0.017% Ext. - 1.76 log D Av t - 2954 T Parallel studies were also carried out investigating the biological oxidation of sphalerite utilizing the acidophilic autotrophic bacterium Thiobacillus Ferroxidans. The effect of such kinetic parameters as pulp density, particle size and Fe(III) on bacterial growth rate and consequently zinc extraction rate, were studied and where appropriate, optimum conditions for bacterial growth were specified. Based on the results of chemical and biological leaching studies, it was apparent that rapid zinc extraction from sphalerite was predominently due to oxidation by Fe(III). The biological oxidation process catalyses the oxidation and regeneration of Fe(III). The proposed combined chemical-biological leach system was simulated in semi continuous fashion. The sphalerite oxidation rates obtained in this system were similar to that predicted by the chemical leach empirical model. 1. Senior Research Metallurgist, CRA Research, Boolaroo, N.S.W. 2. Group Leader-Hydrometallurgy, CRA Research, Boolaroo, N.S.W. 3. Senior Research Scientist, Biotechnology Australia, Roseville, N.S.W. 4. Senior Experimental Officer, Biotechnology Australia, Roseville, N.S.W.

Jan 1, 1986

A simple production technique has been initiated and implemented at Oaky Creek open cut coal mine to optimise recovery of coal from the relatively thin geological seams. The production technique is based upon minimising coal dilution through careful dragline operation and the selective use of mine mobile equipment to clean the top of coal. In addition, recovery of coal from the pits has been increased by refining blasting and dragline methods.The implementation of the recovery optimisation programme at Oaky Creek has provided significant economic benefits from increased yield through the preparation plant by the reduction in dilution, and from increased raw coal tonnage through improved pit recovery methods.

Jan 1, 1990

Recovery Process of Carbon Dioxide with Metal Oxides and Metal Hydroxides

Sep 13, 2010

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A G. L Pratt, M S. Kemp

BHP has used many innovative techniques when recruiting its workforce for the Cannington Project. Looking for a balance of experience and enthusiasm it was necessary to develop pre-selection tests to reduce the initial number of applicants to a manageable number for first interviews in Townsville. Success at this stage led to an applicant, and their spouse, to go through a second interview at the mine site. The full process from application to job offer took up to six months, but the results were felt to be worth the effort. The approach taken has resulted in a highly motivated and flexible workforce. This paper outlines the philosophies behind CanningtonÆs recruitment process, highlights some of the issues associated with the approach, and offers some measures of the outcomes.

Jan 1, 1998

Recycling and Recovering Fine Particles from Auto Shredding Residue (ASR/SR) to Conserve Raw Materials and Protect Environment

Sep 13, 2010

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993

Recycling of Process Water in Sulfides Processing and Flotation Selectivity

Sep 13, 2010

Recycling of Sludge from the Production of Manganese

Sep 13, 2010

Societal influences, needs, and uses for recyclable materials are becoming increasingly important business and economic factors in the traditional natural resource companies. Several metals (such as steel, aluminium, zinc, lead and cadmium) are amenable ro recycle which eliminates solid waste generation and decreases the depletion of natural resources. In recent years, the non-ferrous industries have begun to recycle more materials and the next decade will see even larger recycle efforts. In addition to the traditonal recyclable materials, existing metallurgical plants are, or should be, able to handle and recycle materials viewed as 'hazardous'. Unfortunately, some national and regional regulations hinder, and in some cases prevent, the recycling of certain materials. Zinc Corporation of America (ZCA) is currently the largest producer of zinc metal in the USA and one of the world's largest producers of value-added zinc products. Over the last few years, ZCA has become one of the world's largest recyclers of zinc from various diverse materials. ZCA considers these recyclable materials as valuable 'land mines' that provide economic alternatives to the depletion of natural resources while serving society in the minimisation of solid waste disposal. Using the current production facilities of ZCA as a model, this paper overviews the recycling of zinc-bearing materials with special emphasis on: 1. the amenability for recycle within ZCA's pyrometallurgical and hydrometallurgical operations, 2. the quantities and economics of recycle, 3. the problems of recycling hindered by current national and regional regulations, 4. the concepts of total recycle rather than just recovering zinc while generating a modified solid waste, and 5. the motivators for recycling.

Jan 1, 1993

By Erceg MM

The Red Dome deposit is located about 15 kilometres by road west of Chillagoe in far north Queensland. The deposit is within a well known band of mineralisation which is adjacent to the Chillagoe - Mungana railway line. Earlier this century several mines were operating in this area, some of which were supplying feed-stock to the copper smelters which were operating in Chillagoe at that time.The area around Chillagoe has long been an interesting geological region with numerous locations exhibiting significant gold and base metal mineralisation.The Red Dome area of some time, however it was not became involved that the apparent. The upsurge in seventies added further investment.mineralisation had been known for until Noel Adam, a prospector,true potential of the area became the gold price in the late encouragement for additional

Jan 1, 1986

By S Logan, J Pu, J Milsom, G McDonald

Management of environmental issues is an integral part of the mine decommissioning process. In Queensland, miners must comply with environmental aspects of the Mineral Resources Act and Contaminated Land legislation. Successful decommissioning involves the integration of a final Plan of Operations, decommissioning report addressing the mineÆs commitments included in its Environmental Management Overview Strategy (EMOS), and Site Contamination Report for relinquishment of leases under the Contaminated Land Act (1991). Niugini MiningÆs Red Dome Mine is proceeding through the decommissioning process. This paper discusses the important environmental management issues including sampling programs, management of culturally significant areas, assessment of background concentrations of target analytes, the use of historical reviews and risk assessment techniques, the timing of works, and the remediation/management of large areas of impacted land. The importance of a clear communications plan between key stakeholders is also discussed.

Jan 1, 1998